firewire: fw-sbp2: enforce a retry of __scsi_add_device if bus generation changed

fw-sbp2 is unable to reconnect while performing __scsi_add_device
because there is only a single workqueue thread context available for
both at the moment.  This should be fixed eventually.

An actual failure of __scsi_add_device is easy to handle, but an
incomplete execution of __scsi_add_device with an sdev returned would
remain undetected and leave the SBP-2 target unusable.

Therefore we use a workaround:  If there was a bus reset during
__scsi_add_device (i.e. during the SCSI probe), we remove the new sdev
immediately, log out, and attempt login and SCSI probe again.

Tested-by: Jarod Wilson <jwilson@redhat.com> (earlier version)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

1 files changed, 35 insertions, 14 deletions

diff --git a/drivers/firewire/fw-sbp2.c b/drivers/firewire/fw-sbp2.c
index 323b03bacd29..6d10934c58f1 100644
--- a/drivers/firewire/fw-sbp2.c
+++ b/drivers/firewire/fw-sbp2.c
@@ -762,22 +762,43 @@ static void sbp2_login(struct work_struct *work)
 
         sdev = __scsi_add_device(shost, 0, 0,
                                  scsilun_to_int(&eight_bytes_lun), lu);
-        if (IS_ERR(sdev)) {
-                smp_rmb(); /* generation may have changed */
-                generation = device->generation;
-                smp_rmb(); /* node_id must not be older than generation */
+        /*
+         * FIXME:  We are unable to perform reconnects while in sbp2_login().
+         * Therefore __scsi_add_device() will get into trouble if a bus reset
+         * happens in parallel.  It will either fail or leave us with an
+         * unusable sdev.  As a workaround we check for this and retry the
+         * whole login and SCSI probing.
+         */
 
-                sbp2_send_management_orb(lu, device->node_id, generation,
-                                SBP2_LOGOUT_REQUEST, lu->login_id, NULL);
-                /*
-                 * Set this back to sbp2_login so we fall back and
-                 * retry login on bus reset.
-                 */
-                PREPARE_DELAYED_WORK(&lu->work, sbp2_login);
-        } else {
-                lu->sdev = sdev;
-                scsi_device_put(sdev);
+        /* Reported error during __scsi_add_device() */
+        if (IS_ERR(sdev))
+                goto out_logout_login;
+
+        scsi_device_put(sdev);
+
+        /* Unreported error during __scsi_add_device() */
+        smp_rmb(); /* get current card generation */
+        if (generation != device->card->generation) {
+                scsi_remove_device(sdev);
+                goto out_logout_login;
         }
+
+        /* No error during __scsi_add_device() */
+        lu->sdev = sdev;
+        goto out;
+
+ out_logout_login:
+        smp_rmb(); /* generation may have changed */
+        generation = device->generation;
+        smp_rmb(); /* node_id must not be older than generation */
+
+        sbp2_send_management_orb(lu, device->node_id, generation,
+                                 SBP2_LOGOUT_REQUEST, lu->login_id, NULL);
+        /*
+         * If a bus reset happened, sbp2_update will have requeued
+         * lu->work already.  Reset the work from reconnect to login.
+         */
+        PREPARE_DELAYED_WORK(&lu->work, sbp2_login);
  out:
         sbp2_target_put(tgt);
 }