Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
  sata_via: Delay on vt6420 when starting ATAPI DMA write
  ata: Detect Delkin Devices compact flash
  pata_efar: Enable parallel scanning
  pata_atiixp: enable parallel scan
  [libata] pata_atiixp: add locking for parallel scanning
  [libata] pata_efar: add locking for parallel scanning
  libata: Pass host flags into the pci helper
  [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
  libata: Allow pata_legacy to be built on non-ISA but PCI systems
  pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
  pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
  [libata] pata_at91: fix backslash-continued string
  pata_via: store UDMA masks in via_isa_bridges table
  pata_via: fix address setup timings underlocking
  pata_serverworks: fix error message
  pata_serverworks: fix PIO setup for the second channel
  pata_efar: fix secondary port support
  pata_cypress: fix PIO timings underclocking
  pata_cs5535: use correct values for PIO1 and PIO2 data timings
  pata_cmd64x: remove unused definitions
  ...

1 files changed, 6 insertions, 17 deletions

diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 0bd48e8f21bd..af49bfb57247 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -11,9 +11,7 @@
  *
  *
  * TODO
- *      Maybe PLL mode
- *      Look into engine reset on timeout errors. Should not be
- *              required.
+ *      Look into engine reset on timeout errors. Should not be required.
  */
 
 
@@ -27,7 +25,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME        "pata_hpt366"
-#define DRV_VERSION     "0.6.7"
+#define DRV_VERSION     "0.6.8"
 
 struct hpt_clock {
         u8      xfer_mode;
@@ -207,17 +205,8 @@ static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
 {
         struct hpt_clock *clocks = ap->host->private_data;
         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-        u32 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-        u32 addr2 = 0x51 + 4 * ap->port_no;
+        u32 addr = 0x40 + 4 * adev->devno;
         u32 mask, reg;
-        u8 fast;
-
-        /* Fast interrupt prediction disable, hold off interrupt disable */
-        pci_read_config_byte(pdev, addr2, &fast);
-        if (fast & 0x80) {
-                fast &= ~0x80;
-                pci_write_config_byte(pdev, addr2, fast);
-        }
 
         /* determine timing mask and find matching clock entry */
         if (mode < XFER_MW_DMA_0)
@@ -240,9 +229,9 @@ static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
          * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
          * problems handling I/O errors later.
          */
-        pci_read_config_dword(pdev, addr1, &reg);
+        pci_read_config_dword(pdev, addr, &reg);
         reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
-        pci_write_config_dword(pdev, addr1, reg);
+        pci_write_config_dword(pdev, addr, reg);
 }
 
 /**
@@ -372,7 +361,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
                         break;
         }
         /* Now kick off ATA set up */
-        return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv);
+        return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
 }
 
 #ifdef CONFIG_PM