ARM: at91: remove NEOCORE 926 board

The board is not available anymore and it seems its use
is very limited.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <abelloni@adeneo-embedded.com>

4 files changed, 0 insertions, 395 deletions

diff --git a/arch/arm/configs/at91sam9263_defconfig b/arch/arm/configs/at91sam9263_defconfig
index c5212f43eee6..36fed66bd4b5 100644
--- a/arch/arm/configs/at91sam9263_defconfig
+++ b/arch/arm/configs/at91sam9263_defconfig
@@ -18,7 +18,6 @@ CONFIG_ARCH_AT91=y
 CONFIG_ARCH_AT91SAM9263=y
 CONFIG_MACH_AT91SAM9263EK=y
 CONFIG_MACH_USB_A9263=y
-CONFIG_MACH_NEOCORE926=y
 CONFIG_MTD_AT91_DATAFLASH_CARD=y
 # CONFIG_ARM_THUMB is not set
 CONFIG_AEABI=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 958358c91afd..6071f4c3d654 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -352,12 +352,6 @@ config MACH_USB_A9263
           Select this if you are using a Calao Systems USB-A9263.
           <http://www.calao-systems.com>
 
-config MACH_NEOCORE926
-        bool "Adeneo NEOCORE926"
-        select HAVE_AT91_DATAFLASH_CARD
-        help
-          Select this if you are using the Adeneo Neocore 926 board.
-
 endif
 
 # ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index b38a1dcb79b8..39218ca6d8e8 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -66,7 +66,6 @@ obj-$(CONFIG_MACH_AT91SAM9G10EK) += board-sam9261ek.o
 # AT91SAM9263 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
 obj-$(CONFIG_MACH_USB_A9263)    += board-usb-a926x.o
-obj-$(CONFIG_MACH_NEOCORE926)   += board-neocore926.o
 
 # AT91SAM9RL board-specific support
 obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
deleted file mode 100644
index bc7a1c4a1f6a..000000000000
--- a/arch/arm/mach-at91/board-neocore926.c
+++ /dev/null
@@ -1,387 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-neocore926.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2007 Atmel Corporation
- *  Copyright (C) 2008 ADENEO.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/sizes.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init neocore926_init_early(void)
-{
-        /* Initialize processor: 20 MHz crystal */
-        at91_initialize(20000000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata neocore926_usbh_data = {
-        .ports          = 2,
-        .vbus_pin       = { AT91_PIN_PA24, AT91_PIN_PA21 },
-        .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata neocore926_udc_data = {
-        .vbus_pin       = AT91_PIN_PA25,
-        .pullup_pin     = -EINVAL,              /* pull-up driven by UDC */
-};
-
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
-        return !at91_get_gpio_value(AT91_PIN_PA15);     /* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
-        .model                  = 7843,
-        .x_min                  = 150,
-        .x_max                  = 3830,
-        .y_min                  = 190,
-        .y_max                  = 3830,
-        .vref_delay_usecs       = 100,
-        .x_plate_ohms           = 450,
-        .y_plate_ohms           = 250,
-        .pressure_max           = 15000,
-        .debounce_max           = 1,
-        .debounce_rep           = 0,
-        .debounce_tol           = (~0),
-        .get_pendown_state      = ads7843_pendown_state,
-};
-
-static void __init neocore926_add_device_ts(void)
-{
-        at91_set_B_periph(AT91_PIN_PA15, 1);    /* External IRQ1, with pullup */
-        at91_set_gpio_input(AT91_PIN_PC13, 1);  /* Touchscreen BUSY signal */
-}
-#else
-static void __init neocore926_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info neocore926_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-        {       /* DataFlash card */
-                .modalias       = "mtd_dataflash",
-                .chip_select    = 0,
-                .max_speed_hz   = 15 * 1000 * 1000,
-                .bus_num        = 0,
-        },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-        {
-                .modalias       = "ads7846",
-                .chip_select    = 1,
-                .max_speed_hz   = 125000 * 16,
-                .bus_num        = 0,
-                .platform_data  = &ads_info,
-                .irq            = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
-        },
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata neocore926_mci0_data = {
-        .slot[0] = {
-                .bus_width      = 4,
-                .detect_pin     = AT91_PIN_PE18,
-                .wp_pin         = AT91_PIN_PE19,
-        },
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata neocore926_macb_data = {
-        .phy_irq_pin    = AT91_PIN_PE31,
-        .is_rmii        = 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata neocore926_nand_partition[] = {
-        {
-                .name   = "Linux Kernel",       /* "Partition 1", */
-                .offset = 0,
-                .size   = SZ_8M,
-        },
-        {
-                .name   = "Filesystem",         /* "Partition 2", */
-                .offset = MTDPART_OFS_NXTBLK,
-                .size   = SZ_32M,
-        },
-        {
-                .name   = "Free",               /* "Partition 3", */
-                .offset = MTDPART_OFS_NXTBLK,
-                .size   = MTDPART_SIZ_FULL,
-        },
-};
-
-static struct atmel_nand_data __initdata neocore926_nand_data = {
-        .ale                    = 21,
-        .cle                    = 22,
-        .rdy_pin                = AT91_PIN_PB19,
-        .rdy_pin_active_low     = 1,
-        .enable_pin             = AT91_PIN_PD15,
-        .ecc_mode               = NAND_ECC_SOFT,
-        .parts                  = neocore926_nand_partition,
-        .num_parts              = ARRAY_SIZE(neocore926_nand_partition),
-        .det_pin                = -EINVAL,
-};
-
-static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
-        .ncs_read_setup         = 0,
-        .nrd_setup              = 1,
-        .ncs_write_setup        = 0,
-        .nwe_setup              = 1,
-
-        .ncs_read_pulse         = 4,
-        .nrd_pulse              = 4,
-        .ncs_write_pulse        = 4,
-        .nwe_pulse              = 4,
-
-        .read_cycle             = 6,
-        .write_cycle            = 6,
-
-        .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-        .tdf_cycles             = 2,
-};
-
-static void __init neocore926_add_device_nand(void)
-{
-        /* configure chip-select 3 (NAND) */
-        sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
-
-        at91_add_device_nand(&neocore926_nand_data);
-}
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
-        {
-                .name           = "TX09D50VM1CCA @ 60",
-                .refresh        = 60,
-                .xres           = 240,          .yres           = 320,
-                .pixclock       = KHZ2PICOS(5000),
-
-                .left_margin    = 1,            .right_margin   = 33,
-                .upper_margin   = 1,            .lower_margin   = 0,
-                .hsync_len      = 5,            .vsync_len      = 1,
-
-                .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-                .vmode          = FB_VMODE_NONINTERLACED,
-        },
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
-        .manufacturer   = "HIT",
-        .monitor        = "TX09D70VM1CCA",
-
-        .modedb         = at91_tft_vga_modes,
-        .modedb_len     = ARRAY_SIZE(at91_tft_vga_modes),
-        .hfmin          = 15000,
-        .hfmax          = 64000,
-        .vfmin          = 50,
-        .vfmax          = 150,
-};
-
-#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
-                                        | ATMEL_LCDC_DISTYPE_TFT \
-                                        | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(int on)
-{
-        at91_set_gpio_value(AT91_PIN_PA30, on);
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
-        .lcdcon_is_backlight            = true,
-        .default_bpp                    = 16,
-        .default_dmacon                 = ATMEL_LCDC_DMAEN,
-        .default_lcdcon2                = AT91SAM9263_DEFAULT_LCDCON2,
-        .default_monspecs               = &at91fb_default_monspecs,
-        .atmel_lcdfb_power_control      = at91_lcdc_power_control,
-        .guard_time                     = 1,
-        .lcd_wiring_mode                = ATMEL_LCDC_WIRING_RGB555,
-};
-
-#else
-static struct atmel_lcdfb_info __initdata neocore926_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button neocore926_buttons[] = {
-        {       /* BP1, "leftclic" */
-                .code           = BTN_LEFT,
-                .gpio           = AT91_PIN_PC5,
-                .active_low     = 1,
-                .desc           = "left_click",
-                .wakeup         = 1,
-        },
-        {       /* BP2, "rightclic" */
-                .code           = BTN_RIGHT,
-                .gpio           = AT91_PIN_PC4,
-                .active_low     = 1,
-                .desc           = "right_click",
-                .wakeup         = 1,
-        },
-};
-
-static struct gpio_keys_platform_data neocore926_button_data = {
-        .buttons        = neocore926_buttons,
-        .nbuttons       = ARRAY_SIZE(neocore926_buttons),
-};
-
-static struct platform_device neocore926_button_device = {
-        .name           = "gpio-keys",
-        .id             = -1,
-        .num_resources  = 0,
-        .dev            = {
-                .platform_data  = &neocore926_button_data,
-        }
-};
-
-static void __init neocore926_add_device_buttons(void)
-{
-        at91_set_GPIO_periph(AT91_PIN_PC5, 0);  /* left button */
-        at91_set_deglitch(AT91_PIN_PC5, 1);
-        at91_set_GPIO_periph(AT91_PIN_PC4, 0);  /* right button */
-        at91_set_deglitch(AT91_PIN_PC4, 1);
-
-        platform_device_register(&neocore926_button_device);
-}
-#else
-static void __init neocore926_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- */
-static struct ac97c_platform_data neocore926_ac97_data = {
-        .reset_pin      = AT91_PIN_PA13,
-};
-
-
-static void __init neocore926_board_init(void)
-{
-        /* Serial */
-        /* DBGU on ttyS0. (Rx & Tx only) */
-        at91_register_uart(0, 0, 0);
-
-        /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-        at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-        at91_add_device_serial();
-
-        /* USB Host */
-        at91_add_device_usbh(&neocore926_usbh_data);
-
-        /* USB Device */
-        at91_add_device_udc(&neocore926_udc_data);
-
-        /* SPI */
-        at91_set_gpio_output(AT91_PIN_PE20, 1);         /* select spi0 clock */
-        at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices));
-
-        /* Touchscreen */
-        neocore926_add_device_ts();
-
-        /* MMC */
-        at91_add_device_mci(0, &neocore926_mci0_data);
-
-        /* Ethernet */
-        at91_add_device_eth(&neocore926_macb_data);
-
-        /* NAND */
-        neocore926_add_device_nand();
-
-        /* I2C */
-        at91_add_device_i2c(NULL, 0);
-
-        /* LCD Controller */
-        at91_add_device_lcdc(&neocore926_lcdc_data);
-
-        /* Push Buttons */
-        neocore926_add_device_buttons();
-
-        /* AC97 */
-        at91_add_device_ac97(&neocore926_ac97_data);
-}
-
-MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926")
-        /* Maintainer: ADENEO */
-        .timer          = &at91sam926x_timer,
-        .map_io         = at91_map_io,
-        .handle_irq     = at91_aic_handle_irq,
-        .init_early     = neocore926_init_early,
-        .init_irq       = at91_init_irq_default,
-        .init_machine   = neocore926_board_init,
-MACHINE_END