x86: multi pci root bus with different io resource range, on 64-bit

scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.

this can fix a system without _CRS for multi pci root bus.

Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

2 files changed, 355 insertions, 51 deletions

diff --git a/arch/x86/pci/Makefile_64 b/arch/x86/pci/Makefile_64
index 7d8c467bf143..8fbd19832cf6 100644
--- a/arch/x86/pci/Makefile_64
+++ b/arch/x86/pci/Makefile_64
@@ -13,5 +13,5 @@ obj-y			+= legacy.o irq.o common.o early.o
 # mmconfig has a 64bit special
 obj-$(CONFIG_PCI_MMCONFIG) += mmconfig_64.o direct.o mmconfig-shared.o
 
-obj-$(CONFIG_NUMA)      += k8-bus_64.o
+obj-y           += k8-bus_64.o
 
diff --git a/arch/x86/pci/k8-bus_64.c b/arch/x86/pci/k8-bus_64.c
index dab38310ee97..5e8a9d105edd 100644
--- a/arch/x86/pci/k8-bus_64.c
+++ b/arch/x86/pci/k8-bus_64.c
@@ -7,23 +7,29 @@
 
 /*
  * This discovers the pcibus <-> node mapping on AMD K8.
- *
- * RED-PEN need to call this again on PCI hotplug
- * RED-PEN empty cpus get reported wrong
+ * also get peer root bus resource for io,mmio
  */
 
-#define NODE_ID(dword) ((dword>>4) & 0x07)
-#define LDT_BUS_NUMBER_REGISTER_0 0xE0
-#define LDT_BUS_NUMBER_REGISTER_1 0xE4
-#define LDT_BUS_NUMBER_REGISTER_2 0xE8
-#define LDT_BUS_NUMBER_REGISTER_3 0xEC
-#define NR_LDT_BUS_NUMBER_REGISTERS 4
-#define SECONDARY_LDT_BUS_NUMBER(dword) ((dword >> 16) & 0xFF)
-#define SUBORDINATE_LDT_BUS_NUMBER(dword) ((dword >> 24) & 0xFF)
 
-#define PCI_DEVICE_ID_K8HTCONFIG 0x1100
-#define PCI_DEVICE_ID_K8_10H_HTCONFIG 0x1200
-#define PCI_DEVICE_ID_K8_11H_HTCONFIG 0x1300
+/*
+ * sub bus (transparent) will use entres from 3 to store extra from root,
+ * so need to make sure have enought slot there, increase PCI_BUS_NUM_RESOURCES?
+ */
+#define RES_NUM 16
+struct pci_root_info {
+        char name[12];
+        unsigned int res_num;
+        struct resource res[RES_NUM];
+        int bus_min;
+        int bus_max;
+        int node;
+        int link;
+};
+
+/* 4 at this time, it may become to 32 */
+#define PCI_ROOT_NR 4
+static int pci_root_num;
+static struct pci_root_info pci_root_info[PCI_ROOT_NR];
 
 #ifdef CONFIG_NUMA
 
@@ -55,77 +61,375 @@ int get_mp_bus_to_node(int busnum)
 
         return node;
 }
-
 #endif
 
+void set_pci_bus_resources_arch_default(struct pci_bus *b)
+{
+        int i;
+        int j;
+        struct pci_root_info *info;
+
+        if (!pci_root_num)
+                return;
+
+        for (i = 0; i < pci_root_num; i++) {
+                if (pci_root_info[i].bus_min == b->number)
+                        break;
+        }
+
+        if (i == pci_root_num)
+                return;
+
+        info = &pci_root_info[i];
+        for (j = 0; j < info->res_num; j++) {
+                struct resource *res;
+                struct resource *root;
+
+                res = &info->res[j];
+                b->resource[j] = res;
+                if (res->flags & IORESOURCE_IO)
+                        root = &ioport_resource;
+                else
+                        root = &iomem_resource;
+                insert_resource(root, res);
+        }
+}
+
+#define RANGE_NUM 16
+
+struct res_range {
+        size_t start;
+        size_t end;
+};
+
+static void __init update_range(struct res_range *range, size_t start,
+                                size_t end)
+{
+        int i;
+        int j;
+
+        for (j = 0; j < RANGE_NUM; j++) {
+                if (!range[j].end)
+                        continue;
+                if (start == range[j].start && end < range[j].end) {
+                        range[j].start = end + 1;
+                        break;
+                } else if (start == range[j].start && end == range[j].end) {
+                        range[j].start = 0;
+                        range[j].end = 0;
+                        break;
+                } else if (start > range[j].start && end == range[j].end) {
+                        range[j].end = start - 1;
+                        break;
+                } else if (start > range[j].start && end < range[j].end) {
+                        /* find the new spare */
+                        for (i = 0; i < RANGE_NUM; i++) {
+                                if (range[i].end == 0)
+                                        break;
+                        }
+                        if (i < RANGE_NUM) {
+                                range[i].end = range[j].end;
+                                range[i].start = end + 1;
+                        } else {
+                                printk(KERN_ERR "run of slot in ranges\n");
+                        }
+                        range[j].end = start - 1;
+                        break;
+                }
+        }
+}
+
+static void __init update_res(struct pci_root_info *info, size_t start,
+                              size_t end, unsigned long flags, int merge)
+{
+        int i;
+        struct resource *res;
+
+        if (!merge)
+                goto addit;
+
+        /* try to merge it with old one */
+        for (i = 0; i < info->res_num; i++) {
+                res = &info->res[i];
+                if (res->flags != flags)
+                        continue;
+                if (res->end + 1 == start) {
+                        res->end = end;
+                        return;
+                } else if (end + 1 == res->start) {
+                        res->start = start;
+                        return;
+                }
+        }
+
+addit:
+
+        /* need to add that */
+        if (info->res_num >= RES_NUM)
+                return;
+
+        res = &info->res[info->res_num];
+        res->name = info->name;
+        res->flags = flags;
+        res->start = start;
+        res->end = end;
+        res->child = NULL;
+        info->res_num++;
+}
+
+struct pci_hostbridge_probe {
+        u32 bus;
+        u32 slot;
+        u32 vendor;
+        u32 device;
+};
+
+static struct pci_hostbridge_probe pci_probes[] __initdata = {
+        { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
+        { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
+        { 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
+        { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+};
+
 /**
  * early_fill_mp_bus_to_node()
  * called before pcibios_scan_root and pci_scan_bus
  * fills the mp_bus_to_cpumask array based according to the LDT Bus Number
  * Registers found in the K8 northbridge
  */
-__init static int
-early_fill_mp_bus_to_node(void)
+static int __init early_fill_mp_bus_info(void)
 {
-#ifdef CONFIG_NUMA
-        int i, j;
+        int i;
+        int j;
+        unsigned bus;
         unsigned slot;
-        u32 ldtbus;
-        u32 id;
+        int found;
         int node;
-        u16 deviceid;
-        u16 vendorid;
-        int min_bus;
-        int max_bus;
-
-        static int lbnr[NR_LDT_BUS_NUMBER_REGISTERS] = {
-                LDT_BUS_NUMBER_REGISTER_0,
-                LDT_BUS_NUMBER_REGISTER_1,
-                LDT_BUS_NUMBER_REGISTER_2,
-                LDT_BUS_NUMBER_REGISTER_3
-        };
+        int link;
+        int def_node;
+        int def_link;
+        struct pci_root_info *info;
+        u32 reg;
+        struct resource *res;
+        size_t start;
+        size_t end;
+        struct res_range range[RANGE_NUM];
+        u64 val;
+        u32 address;
 
+#ifdef CONFIG_NUMA
         for (i = 0; i < BUS_NR; i++)
                 mp_bus_to_node[i] = -1;
+#endif
 
         if (!early_pci_allowed())
                 return -1;
 
-        slot = 0x18;
-        id = read_pci_config(0, slot, 0, PCI_VENDOR_ID);
+        found = 0;
+        for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+                u32 id;
+                u16 device;
+                u16 vendor;
 
-        vendorid = id & 0xffff;
-        if (vendorid != PCI_VENDOR_ID_AMD)
-                goto out;
+                bus = pci_probes[i].bus;
+                slot = pci_probes[i].slot;
+                id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
 
-        deviceid = (id>>16) & 0xffff;
-        if ((deviceid != PCI_DEVICE_ID_K8HTCONFIG) &&
-            (deviceid != PCI_DEVICE_ID_K8_10H_HTCONFIG) &&
-            (deviceid != PCI_DEVICE_ID_K8_11H_HTCONFIG))
-                goto out;
+                vendor = id & 0xffff;
+                device = (id>>16) & 0xffff;
+                if (pci_probes[i].vendor == vendor &&
+                    pci_probes[i].device == device) {
+                        found = 1;
+                        break;
+                }
+        }
+
+        if (!found)
+                return 0;
 
-        for (i = 0; i < NR_LDT_BUS_NUMBER_REGISTERS; i++) {
-                ldtbus = read_pci_config(0, slot, 1, lbnr[i]);
+        pci_root_num = 0;
+        for (i = 0; i < 4; i++) {
+                int min_bus;
+                int max_bus;
+                reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
 
                 /* Check if that register is enabled for bus range */
-                if ((ldtbus & 7) != 3)
+                if ((reg & 7) != 3)
                         continue;
 
-                min_bus = SECONDARY_LDT_BUS_NUMBER(ldtbus);
-                max_bus = SUBORDINATE_LDT_BUS_NUMBER(ldtbus);
-                node = NODE_ID(ldtbus);
+                min_bus = (reg >> 16) & 0xff;
+                max_bus = (reg >> 24) & 0xff;
+                node = (reg >> 4) & 0x07;
+#ifdef CONFIG_NUMA
                 for (j = min_bus; j <= max_bus; j++)
                         mp_bus_to_node[j] = (unsigned char) node;
+#endif
+                link = (reg >> 8) & 0x03;
+
+                info = &pci_root_info[pci_root_num];
+                info->bus_min = min_bus;
+                info->bus_max = max_bus;
+                info->node = node;
+                info->link = link;
+                sprintf(info->name, "PCI Bus #%02x", min_bus);
+                pci_root_num++;
         }
 
-out:
+        /* get the default node and link for left over res */
+        reg = read_pci_config(bus, slot, 0, 0x60);
+        def_node = (reg >> 8) & 0x07;
+        reg = read_pci_config(bus, slot, 0, 0x64);
+        def_link = (reg >> 8) & 0x03;
+
+        memset(range, 0, sizeof(range));
+        range[0].end = 0xffff;
+        /* io port resource */
+        for (i = 0; i < 4; i++) {
+                reg = read_pci_config(bus, slot, 1, 0xc0 + (i << 3));
+                if (!(reg & 3))
+                        continue;
+
+                start = reg & 0xfff000;
+                reg = read_pci_config(bus, slot, 1, 0xc4 + (i << 3));
+                node = reg & 0x07;
+                link = (reg >> 4) & 0x03;
+                end = (reg & 0xfff000) | 0xfff;
+
+                /* find the position */
+                for (j = 0; j < pci_root_num; j++) {
+                        info = &pci_root_info[j];
+                        if (info->node == node && info->link == link)
+                                break;
+                }
+                if (j == pci_root_num)
+                        continue; /* not found */
+
+                info = &pci_root_info[j];
+                update_res(info, start, end, IORESOURCE_IO, 0);
+                update_range(range, start, end);
+        }
+        /* add left over io port range to def node/link, [0, 0xffff] */
+        /* find the position */
+        for (j = 0; j < pci_root_num; j++) {
+                info = &pci_root_info[j];
+                if (info->node == def_node && info->link == def_link)
+                        break;
+        }
+        if (j < pci_root_num) {
+                info = &pci_root_info[j];
+                for (i = 0; i < RANGE_NUM; i++) {
+                        if (!range[i].end)
+                                continue;
+
+                        update_res(info, range[i].start, range[i].end,
+                                   IORESOURCE_IO, 1);
+                }
+        }
+
+        memset(range, 0, sizeof(range));
+        /* 0xfd00000000-0xffffffffff for HT */
+        /* 0xfc00000000-0xfcffffffff for Family 10h mmconfig*/
+        range[0].end = 0xfbffffffffULL;
+
+        /* need to take out [0, TOM) for RAM*/
+        address = MSR_K8_TOP_MEM1;
+        rdmsrl(address, val);
+        end = (val & 0xffffff8000000ULL);
+        printk(KERN_INFO "TOM: %016lx aka %ldM\n", end, end>>20);
+        if (end < (1ULL<<32))
+                update_range(range, 0, end - 1);
+
+        /* mmio resource */
+        for (i = 0; i < 8; i++) {
+                reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
+                if (!(reg & 3))
+                        continue;
+
+                start = reg & 0xffffff00; /* 39:16 on 31:8*/
+                start <<= 8;
+                reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
+                node = reg & 0x07;
+                link = (reg >> 4) & 0x03;
+                end = (reg & 0xffffff00);
+                end <<= 8;
+                end |= 0xffff;
+
+                /* find the position */
+                for (j = 0; j < pci_root_num; j++) {
+                        info = &pci_root_info[j];
+                        if (info->node == node && info->link == link)
+                                break;
+                }
+                if (j == pci_root_num)
+                        continue; /* not found */
+
+                info = &pci_root_info[j];
+                update_res(info, start, end, IORESOURCE_MEM, 0);
+                update_range(range, start, end);
+        }
+
+        /* need to take out [4G, TOM2) for RAM*/
+        /* SYS_CFG */
+        address = MSR_K8_SYSCFG;
+        rdmsrl(address, val);
+        /* TOP_MEM2 is enabled? */
+        if (val & (1<<21)) {
+                /* TOP_MEM2 */
+                address = MSR_K8_TOP_MEM2;
+                rdmsrl(address, val);
+                end = (val & 0xffffff8000000ULL);
+                printk(KERN_INFO "TOM2: %016lx aka %ldM\n", end, end>>20);
+                update_range(range, 1ULL<<32, end - 1);
+        }
+
+        /*
+         * add left over mmio range to def node/link ?
+         * that is tricky, just record range in from start_min to 4G
+         */
+        for (j = 0; j < pci_root_num; j++) {
+                info = &pci_root_info[j];
+                if (info->node == def_node && info->link == def_link)
+                        break;
+        }
+        if (j < pci_root_num) {
+                info = &pci_root_info[j];
+
+                for (i = 0; i < RANGE_NUM; i++) {
+                        if (!range[i].end)
+                                continue;
+
+                        update_res(info, range[i].start, range[i].end,
+                                   IORESOURCE_MEM, 1);
+                }
+        }
+
+#ifdef CONFIG_NUMA
         for (i = 0; i < BUS_NR; i++) {
                 node = mp_bus_to_node[i];
                 if (node >= 0)
                         printk(KERN_DEBUG "bus: %02x to node: %02x\n", i, node);
         }
 #endif
+
+        for (i = 0; i < pci_root_num; i++) {
+                int res_num;
+                int busnum;
+
+                info = &pci_root_info[i];
+                res_num = info->res_num;
+                busnum = info->bus_min;
+                printk(KERN_DEBUG "bus: [%02x,%02x] on node %x link %x\n",
+                       info->bus_min, info->bus_max, info->node, info->link);
+                for (j = 0; j < res_num; j++) {
+                        res = &info->res[j];
+                        printk(KERN_DEBUG "bus: %02x index %x %s: [%llx, %llx]\n",
+                               busnum, j,
+                               (res->flags & IORESOURCE_IO)?"io port":"mmio",
+                               res->start, res->end);
+                }
+        }
+
         return 0;
 }
 
-postcore_initcall(early_fill_mp_bus_to_node);
+postcore_initcall(early_fill_mp_bus_info);