powerpc/85xx: Add BSC9131 RDB Support

BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte
    shared L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel
      Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
      UP/DL Channel processing, and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
      Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
      Inversion operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
      with ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network
      acceleration including IEEE 1588. v2 hardware support and
      virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single
      port) and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD
      support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

 BSC9131RDB Overview
 ----------------------
    BSC9131 SoC
    1Gbyte DDR3 (on board DDR)
    128Mbyte 2K page size NAND Flash
    256 Kbit M24256 I2C EEPROM
    128 Mbit SPI Flash memory
    USB-ULPI
    eTSEC1: Connected to RGMII PHY
    eTSEC2: Connected to RGMII PHY
    DUART interface: supports one UARTs up to 115200 bps for console display

 Linux runs on e500v2 core and access some DSP peripherals like AIC

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 193 insertions, 0 deletions

diff --git a/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi b/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi
new file mode 100644
index 000000000000..5180d9d37989
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi
@@ -0,0 +1,193 @@
+/*
+ * BSC9131 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+        #address-cells = <2>;
+        #size-cells = <1>;
+        compatible = "fsl,ifc", "simple-bus";
+        interrupts = <16 2 0 0 20 2 0 0>;
+};
+
+&soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+        device_type = "soc";
+        compatible = "fsl,bsc9131-immr", "simple-bus";
+        bus-frequency = <0>;            // Filled out by uboot.
+
+        ecm-law@0 {
+                compatible = "fsl,ecm-law";
+                reg = <0x0 0x1000>;
+                fsl,num-laws = <12>;
+        };
+
+        ecm@1000 {
+                compatible = "fsl,bsc9131-ecm", "fsl,ecm";
+                reg = <0x1000 0x1000>;
+                interrupts = <16 2 0 0>;
+        };
+
+        memory-controller@2000 {
+                compatible = "fsl,bsc9131-memory-controller";
+                reg = <0x2000 0x1000>;
+                interrupts = <16 2 0 0>;
+        };
+
+/include/ "pq3-i2c-0.dtsi"
+        i2c@3000 {
+                interrupts = <17 2 0 0>;
+        };
+
+/include/ "pq3-i2c-1.dtsi"
+        i2c@3100 {
+                interrupts = <17 2 0 0>;
+        };
+
+/include/ "pq3-duart-0.dtsi"
+        serial0: serial@4500 {
+                interrupts = <18 2 0 0>;
+        };
+
+        serial1: serial@4600 {
+                interrupts = <18 2 0 0 >;
+        };
+/include/ "pq3-espi-0.dtsi"
+        spi0: spi@7000 {
+                fsl,espi-num-chipselects = <1>;
+                interrupts = <22 0x2 0 0>;
+        };
+
+/include/ "pq3-gpio-0.dtsi"
+        gpio-controller@f000 {
+                interrupts = <19 0x2 0 0>;
+                };
+
+        L2: l2-cache-controller@20000 {
+                compatible = "fsl,bsc9131-l2-cache-controller";
+                reg = <0x20000 0x1000>;
+                cache-line-size = <32>; // 32 bytes
+                cache-size = <0x40000>; // L2,256K
+                interrupts = <16 2 0 0>;
+        };
+
+/include/ "pq3-dma-0.dtsi"
+
+dma@21300 {
+
+        dma-channel@0 {
+                interrupts = <62 2 0 0>;
+        };
+
+        dma-channel@80 {
+                interrupts = <63 2 0 0>;
+        };
+
+        dma-channel@100 {
+                interrupts = <64 2 0 0>;
+        };
+
+        dma-channel@180 {
+                interrupts = <65 2 0 0>;
+        };
+};
+
+/include/ "pq3-usb2-dr-0.dtsi"
+usb@22000 {
+        compatible = "fsl-usb2-dr","fsl-usb2-dr-v2.2";
+        interrupts = <40 0x2 0 0>;
+};
+
+/include/ "pq3-esdhc-0.dtsi"
+        sdhc@2e000 {
+                fsl,sdhci-auto-cmd12;
+                interrupts = <41 0x2 0 0>;
+        };
+
+/include/ "pq3-sec4.4-0.dtsi"
+crypto@30000 {
+        interrupts       = <57 2 0 0>;
+
+        sec_jr0: jr@1000 {
+                interrupts       = <58 2 0 0>;
+        };
+
+        sec_jr1: jr@2000 {
+                interrupts       = <59 2 0 0>;
+        };
+
+        sec_jr2: jr@3000 {
+                interrupts       = <60 2 0 0>;
+        };
+
+        sec_jr3: jr@4000 {
+                interrupts       = <61 2 0 0>;
+        };
+};
+
+/include/ "pq3-mpic.dtsi"
+
+timer@41100 {
+        compatible = "fsl,mpic-v1.2-msgr", "fsl,mpic-msg";
+        reg = <0x41400 0x200>;
+        interrupts = <
+                0xb0 2
+                0xb1 2
+                0xb2 2
+                0xb3 2>;
+};
+
+/include/ "pq3-etsec2-0.dtsi"
+enet0: ethernet@b0000 {
+        queue-group@b0000 {
+                fsl,rx-bit-map = <0xff>;
+                fsl,tx-bit-map = <0xff>;
+                interrupts = <26 2 0 0 27 2 0 0 28 2 0 0>;
+        };
+};
+
+/include/ "pq3-etsec2-1.dtsi"
+enet1: ethernet@b1000 {
+        queue-group@b1000 {
+                fsl,rx-bit-map = <0xff>;
+                fsl,tx-bit-map = <0xff>;
+                interrupts = <33 2 0 0 34 2 0 0 35 2 0 0>;
+        };
+};
+
+global-utilities@e0000 {
+                compatible = "fsl,bsc9131-guts";
+                reg = <0xe0000 0x1000>;
+                fsl,has-rstcr;
+        };
+};