ARM: OMAP: SRAM: Split sram24xx.S into sram242x.S and sram243x.S

Split sram24xx.S into sram242x.S and sram243x.S

Signed-off-by: Tony Lindgren <tony@atomide.com>

8 files changed, 576 insertions, 95 deletions

diff --git a/arch/arm/mach-omap1/sram.S b/arch/arm/mach-omap1/sram.S
index 9e1813c77e05..126d252062d7 100644
--- a/arch/arm/mach-omap1/sram.S
+++ b/arch/arm/mach-omap1/sram.S
@@ -18,7 +18,7 @@
 /*
  * Reprograms ULPD and CKCTL.
  */
-ENTRY(sram_reprogram_clock)
+ENTRY(omap1_sram_reprogram_clock)
         stmfd   sp!, {r0 - r12, lr}             @ save registers on stack
 
         mov     r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000
@@ -53,5 +53,5 @@ lock:	ldrh	r4, [r2], #0			@ read back dpll value
 
 out:
         ldmfd   sp!, {r0 - r12, pc}             @ restore regs and return
-ENTRY(sram_reprogram_clock_sz)
-        .word   . - sram_reprogram_clock
+ENTRY(omap1_sram_reprogram_clock_sz)
+        .word   . - omap1_sram_reprogram_clock
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 6c59b267105d..c2477428e351 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -3,9 +3,13 @@
 #
 
 # Common support
-obj-y := irq.o id.o io.o sram242x.o memory.o control.o prcm.o clock.o mux.o \
+obj-y := irq.o id.o io.o memory.o control.o prcm.o clock.o mux.o \
                 devices.o serial.o gpmc.o timer-gp.o
 
+# Functions loaded to SRAM
+obj-$(CONFIG_ARCH_OMAP2420)             += sram242x.o
+obj-$(CONFIG_ARCH_OMAP2430)             += sram243x.o
+
 # Power Management
 obj-$(CONFIG_PM) += pm.o sleep.o
 
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index ab9fc57d25f1..0243480e8bfe 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -603,7 +603,8 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate)
         clk->rate = clk->parent->rate / new_div;
 
         if (clk->flags & DELAYED_APP && cpu_is_omap24xx()) {
-                __raw_writel(OMAP24XX_VALID_CONFIG, OMAP24XX_PRCM_CLKCFG_CTRL);
+                prm_write_mod_reg(OMAP24XX_VALID_CONFIG,
+                        OMAP24XX_GR_MOD, OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET);
                 wmb();
         }
 
diff --git a/arch/arm/mach-omap2/prcm-common.h b/arch/arm/mach-omap2/prcm-common.h
index cacb34086e35..54c32f482131 100644
--- a/arch/arm/mach-omap2/prcm-common.h
+++ b/arch/arm/mach-omap2/prcm-common.h
@@ -32,6 +32,7 @@
 
 
 /* Chip-specific module offsets */
+#define OMAP24XX_GR_MOD                                 OCP_MOD
 #define OMAP24XX_DSP_MOD                                0x800
 
 #define OMAP2430_MDM_MOD                                0xc00
diff --git a/arch/arm/mach-omap2/prm.h b/arch/arm/mach-omap2/prm.h
index 618f8111658a..dcdb35bfa0c0 100644
--- a/arch/arm/mach-omap2/prm.h
+++ b/arch/arm/mach-omap2/prm.h
@@ -38,13 +38,29 @@
  *
  */
 
+/* Global 24xx registers in GR_MOD (Same as OCP_MOD for 24xx) */
+#define OMAP24XX_PRCM_VOLTCTRL_OFFSET           0x0050
+#define OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET        0x0080
+
+/* 242x GR_MOD registers, use these only for assembly code */
+#define OMAP242X_PRCM_VOLTCTRL          OMAP2420_PRM_REGADDR(OMAP24XX_GR_MOD,   \
+                                                OMAP24XX_PRCM_VOLTCTRL_OFFSET)
+#define OMAP242X_PRCM_CLKCFG_CTRL       OMAP2420_PRM_REGADDR(OMAP24XX_GR_MOD,   \
+                                                OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET)
+
+/* 243x GR_MOD registers, use these only for assembly code */
+#define OMAP243X_PRCM_VOLTCTRL          OMAP2430_PRM_REGADDR(OMAP24XX_GR_MOD,   \
+                                                OMAP24XX_PRCM_VOLTCTRL_OFFSET)
+#define OMAP243X_PRCM_CLKCFG_CTRL       OMAP2430_PRM_REGADDR(OMAP24XX_GR_MOD,   \
+                                                OMAP24XX_PRCM_CLKCFG_CTRL_OFFSET)
+
+/* These will disappear */
 #define OMAP24XX_PRCM_REVISION          OMAP_PRM_REGADDR(OCP_MOD, 0x0000)
 #define OMAP24XX_PRCM_SYSCONFIG         OMAP_PRM_REGADDR(OCP_MOD, 0x0010)
 
 #define OMAP24XX_PRCM_IRQSTATUS_MPU     OMAP_PRM_REGADDR(OCP_MOD, 0x0018)
 #define OMAP24XX_PRCM_IRQENABLE_MPU     OMAP_PRM_REGADDR(OCP_MOD, 0x001c)
 
-#define OMAP24XX_PRCM_VOLTCTRL          OMAP_PRM_REGADDR(OCP_MOD, 0x0050)
 #define OMAP24XX_PRCM_VOLTST            OMAP_PRM_REGADDR(OCP_MOD, 0x0054)
 #define OMAP24XX_PRCM_CLKSRC_CTRL       OMAP_PRM_REGADDR(OCP_MOD, 0x0060)
 #define OMAP24XX_PRCM_CLKOUT_CTRL       OMAP_PRM_REGADDR(OCP_MOD, 0x0070)
diff --git a/arch/arm/mach-omap2/sram242x.S b/arch/arm/mach-omap2/sram242x.S
index 4a9e49140716..4c274510f3e9 100644
--- a/arch/arm/mach-omap2/sram242x.S
+++ b/arch/arm/mach-omap2/sram242x.S
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-omap2/sram-fn.S
+ * linux/arch/arm/mach-omap2/sram242x.S
  *
  * Omap2 specific functions that need to be run in internal SRAM
  *
@@ -27,22 +27,20 @@
 #include <asm/arch/io.h>
 #include <asm/hardware.h>
 
-#include "sdrc.h"
 #include "prm.h"
 #include "cm.h"
-
-#define TIMER_32KSYNCT_CR_V     IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
+#include "sdrc.h"
 
         .text
 
-ENTRY(sram_ddr_init)
+ENTRY(omap242x_sram_ddr_init)
         stmfd   sp!, {r0 - r12, lr}     @ save registers on stack
 
         mov     r12, r2                 @ capture CS1 vs CS0
         mov     r8, r3                  @ capture force parameter
 
         /* frequency shift down */
-        ldr     r2, cm_clksel2_pll      @ get address of dpllout reg
+        ldr     r2, omap242x_sdi_cm_clksel2_pll @ get address of dpllout reg
         mov     r3, #0x1                @ value for 1x operation
         str     r3, [r2]                @ go to L1-freq operation
 
@@ -51,7 +49,7 @@ ENTRY(sram_ddr_init)
         bl voltage_shift                @ go drop voltage
 
         /* dll lock mode */
-        ldr     r11, sdrc_dlla_ctrl     @ addr of dlla ctrl
+        ldr     r11, omap242x_sdi_sdrc_dlla_ctrl        @ addr of dlla ctrl
         ldr     r10, [r11]              @ get current val
         cmp     r12, #0x1               @ cs1 base (2422 es2.05/1)
         addeq   r11, r11, #0x8          @ if cs1 base, move to DLLB
@@ -102,7 +100,7 @@ i_dll_delay:
          * wait for it to finish, use 32k sync counter, 1tick=31uS.
          */
 voltage_shift:
-        ldr     r4, prcm_voltctrl       @ get addr of volt ctrl.
+        ldr     r4, omap242x_sdi_prcm_voltctrl  @ get addr of volt ctrl.
         ldr     r5, [r4]                @ get value.
         ldr     r6, prcm_mask_val       @ get value of mask
         and     r5, r5, r6              @ apply mask to clear bits
@@ -112,7 +110,7 @@ voltage_shift:
         orr     r5, r5, r3              @ build value for force
         str     r5, [r4]                @ Force transition to L1
 
-        ldr     r3, timer_32ksynct_cr   @ get addr of counter
+        ldr     r3, omap242x_sdi_timer_32ksynct_cr      @ get addr of counter
         ldr     r5, [r3]                @ get value
         add     r5, r5, #0x3            @ give it at most 93uS
 volt_delay:
@@ -121,32 +119,31 @@ volt_delay:
         bhi     volt_delay              @ not yet->branch
         mov     pc, lr                  @ back to caller.
 
-/* relative load constants */
-cm_clksel2_pll:
+omap242x_sdi_cm_clksel2_pll:
         .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
-sdrc_dlla_ctrl:
+omap242x_sdi_sdrc_dlla_ctrl:
         .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
-prcm_voltctrl:
-        .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
+omap242x_sdi_prcm_voltctrl:
+        .word OMAP242X_PRCM_VOLTCTRL
 prcm_mask_val:
         .word 0xFFFF3FFC
-timer_32ksynct_cr:
-        .word TIMER_32KSYNCT_CR_V
-ENTRY(sram_ddr_init_sz)
-        .word   . - sram_ddr_init
+omap242x_sdi_timer_32ksynct_cr:
+        .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010)
+ENTRY(omap242x_sram_ddr_init_sz)
+        .word   . - omap242x_sram_ddr_init
 
 /*
  * Reprograms memory timings.
  * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR]
  * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0
  */
-ENTRY(sram_reprogram_sdrc)
+ENTRY(omap242x_sram_reprogram_sdrc)
         stmfd   sp!, {r0 - r10, lr}     @ save registers on stack
         mov     r3, #0x0                @ clear for mrc call
         mcr     p15, 0, r3, c7, c10, 4  @ memory barrier, finish ARM SDR/DDR
         nop
         nop
-        ldr     r6, ddr_sdrc_rfr_ctrl   @ get addr of refresh reg
+        ldr     r6, omap242x_srs_sdrc_rfr_ctrl  @ get addr of refresh reg
         ldr     r5, [r6]                @ get value
         mov     r5, r5, lsr #8          @ isolate rfr field and drop burst
 
@@ -160,7 +157,7 @@ ENTRY(sram_reprogram_sdrc)
         movne   r5, r5, lsl #1          @ mult by 2 if to full
         mov     r5, r5, lsl #8          @ put rfr field back into place
         add     r5, r5, #0x1            @ turn on burst of 1
-        ldr     r4, ddr_cm_clksel2_pll  @ get address of out reg
+        ldr     r4, omap242x_srs_cm_clksel2_pll @ get address of out reg
         ldr     r3, [r4]                @ get curr value
         orr     r3, r3, #0x3
         bic     r3, r3, #0x3            @ clear lower bits
@@ -181,7 +178,7 @@ ENTRY(sram_reprogram_sdrc)
         bne     freq_out                @ leave if SDR, no DLL function
 
         /* With DDR, we need to take care of the DLL for the frequency change */
-        ldr     r2, ddr_sdrc_dlla_ctrl  @ addr of dlla ctrl
+        ldr     r2, omap242x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl
         str     r1, [r2]                @ write out new SDRC_DLLA_CTRL
         add     r2, r2, #0x8            @ addr to SDRC_DLLB_CTRL
         str     r1, [r2]                @ commit to SDRC_DLLB_CTRL
@@ -197,7 +194,7 @@ freq_out:
      *  wait for it to finish, use 32k sync counter, 1tick=31uS.
      */
 voltage_shift_c:
-        ldr     r10, ddr_prcm_voltctrl  @ get addr of volt ctrl
+        ldr     r10, omap242x_srs_prcm_voltctrl @ get addr of volt ctrl
         ldr     r8, [r10]               @ get value
         ldr     r7, ddr_prcm_mask_val   @ get value of mask
         and     r8, r8, r7              @ apply mask to clear bits
@@ -207,7 +204,7 @@ voltage_shift_c:
         orr     r8, r8, r7              @ build value for force
         str     r8, [r10]               @ Force transition to L1
 
-        ldr     r10, ddr_timer_32ksynct @ get addr of counter
+        ldr     r10, omap242x_srs_timer_32ksynct        @ get addr of counter
         ldr     r8, [r10]               @ get value
         add     r8, r8, #0x2            @ give it at most 62uS (min 31+)
 volt_delay_c:
@@ -216,39 +213,39 @@ volt_delay_c:
         bhi     volt_delay_c            @ not yet->branch
         mov     pc, lr                  @ back to caller
 
-ddr_cm_clksel2_pll:
+omap242x_srs_cm_clksel2_pll:
         .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
-ddr_sdrc_dlla_ctrl:
+omap242x_srs_sdrc_dlla_ctrl:
         .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
-ddr_sdrc_rfr_ctrl:
+omap242x_srs_sdrc_rfr_ctrl:
         .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-ddr_prcm_voltctrl:
-        .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
+omap242x_srs_prcm_voltctrl:
+        .word OMAP242X_PRCM_VOLTCTRL
 ddr_prcm_mask_val:
         .word 0xFFFF3FFC
-ddr_timer_32ksynct:
-        .word TIMER_32KSYNCT_CR_V
+omap242x_srs_timer_32ksynct:
+        .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010)
 
-ENTRY(sram_reprogram_sdrc_sz)
-        .word   . - sram_reprogram_sdrc
+ENTRY(omap242x_sram_reprogram_sdrc_sz)
+        .word   . - omap242x_sram_reprogram_sdrc
 
 /*
  * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode.
  */
-ENTRY(sram_set_prcm)
+ENTRY(omap242x_sram_set_prcm)
         stmfd   sp!, {r0-r12, lr}       @ regs to stack
         adr     r4, pbegin              @ addr of preload start
         adr     r8, pend                @ addr of preload end
         mcrr    p15, 1, r8, r4, c12     @ preload into icache
 pbegin:
         /* move into fast relock bypass */
-        ldr     r8, pll_ctl             @ get addr
+        ldr     r8, omap242x_ssp_pll_ctl        @ get addr
         ldr     r5, [r8]                @ get val
         mvn     r6, #0x3                @ clear mask
         and     r5, r5, r6              @ clear field
         orr     r7, r5, #0x2            @ fast relock val
         str     r7, [r8]                @ go to fast relock
-        ldr     r4, pll_stat            @ addr of stat
+        ldr     r4, omap242x_ssp_pll_stat       @ addr of stat
 block:
         /* wait for bypass */
         ldr     r8, [r4]                @ stat value
@@ -257,10 +254,10 @@ block:
         bne     block                   @ loop if not
 
         /* set new dpll dividers _after_ in bypass */
-        ldr     r4, pll_div             @ get addr
+        ldr     r4, omap242x_ssp_pll_div        @ get addr
         str     r0, [r4]                @ set dpll ctrl val
 
-        ldr     r4, set_config          @ get addr
+        ldr     r4, omap242x_ssp_set_config     @ get addr
         mov     r8, #1                  @ valid cfg msk
         str     r8, [r4]                @ make dividers take
 
@@ -274,8 +271,8 @@ wait_a_bit:
         beq     pend                    @ jump over dpll relock
 
         /* relock DPLL with new vals */
-        ldr     r5, pll_stat            @ get addr
-        ldr     r4, pll_ctl             @ get addr
+        ldr     r5, omap242x_ssp_pll_stat       @ get addr
+        ldr     r4, omap242x_ssp_pll_ctl        @ get addr
         orr     r8, r7, #0x3            @ val for lock dpll
         str     r8, [r4]                @ set val
         mov     r0, #1000               @ dead spin a bit
@@ -289,9 +286,9 @@ wait_lock:
         bne     wait_lock               @ wait if not
 pend:
         /* update memory timings & briefly lock dll */
-        ldr     r4, sdrc_rfr            @ get addr
+        ldr     r4, omap242x_ssp_sdrc_rfr       @ get addr
         str     r1, [r4]                @ update refresh timing
-        ldr     r11, dlla_ctrl          @ get addr of DLLA ctrl
+        ldr     r11, omap242x_ssp_dlla_ctrl     @ get addr of DLLA ctrl
         ldr     r10, [r11]              @ get current val
         mvn     r9, #0x4                @ mask to get clear bit2
         and     r10, r10, r9            @ clear bit2 for lock mode
@@ -307,18 +304,18 @@ wait_dll_lock:
         nop
         ldmfd   sp!, {r0-r12, pc}       @ restore regs and return
 
-set_config:
-        .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x80)
-pll_ctl:
-        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_FCLKEN1)
-pll_stat:
-        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST1)
-pll_div:
-        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL)
-sdrc_rfr:
+omap242x_ssp_set_config:
+        .word OMAP242X_PRCM_CLKCFG_CTRL
+omap242x_ssp_pll_ctl:
+        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKEN)
+omap242x_ssp_pll_stat:
+        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST)
+omap242x_ssp_pll_div:
+        .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL1)
+omap242x_ssp_sdrc_rfr:
         .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-dlla_ctrl:
+omap242x_ssp_dlla_ctrl:
         .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
 
-ENTRY(sram_set_prcm_sz)
-        .word   . - sram_set_prcm
+ENTRY(omap242x_sram_set_prcm_sz)
+        .word   . - omap242x_sram_set_prcm
diff --git a/arch/arm/mach-omap2/sram243x.S b/arch/arm/mach-omap2/sram243x.S
new file mode 100644
index 000000000000..a3fa48dc08cd
--- /dev/null
+++ b/arch/arm/mach-omap2/sram243x.S
@@ -0,0 +1,321 @@
+/*
+ * linux/arch/arm/mach-omap2/sram243x.S
+ *
+ * Omap2 specific functions that need to be run in internal SRAM
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/hardware.h>
+
+#include "prm.h"
+#include "cm.h"
+#include "sdrc.h"
+
+        .text
+
+ENTRY(omap243x_sram_ddr_init)
+        stmfd   sp!, {r0 - r12, lr}     @ save registers on stack
+
+        mov     r12, r2                 @ capture CS1 vs CS0
+        mov     r8, r3                  @ capture force parameter
+
+        /* frequency shift down */
+        ldr     r2, omap243x_sdi_cm_clksel2_pll @ get address of dpllout reg
+        mov     r3, #0x1                @ value for 1x operation
+        str     r3, [r2]                @ go to L1-freq operation
+
+        /* voltage shift down */
+        mov r9, #0x1                    @ set up for L1 voltage call
+        bl voltage_shift                @ go drop voltage
+
+        /* dll lock mode */
+        ldr     r11, omap243x_sdi_sdrc_dlla_ctrl        @ addr of dlla ctrl
+        ldr     r10, [r11]              @ get current val
+        cmp     r12, #0x1               @ cs1 base (2422 es2.05/1)
+        addeq   r11, r11, #0x8          @ if cs1 base, move to DLLB
+        mvn     r9, #0x4                @ mask to get clear bit2
+        and     r10, r10, r9            @ clear bit2 for lock mode.
+        orr     r10, r10, #0x8          @ make sure DLL on (es2 bit pos)
+        orr     r10, r10, #0x2          @ 90 degree phase for all below 133Mhz
+        str     r10, [r11]              @ commit to DLLA_CTRL
+        bl      i_dll_wait              @ wait for dll to lock
+
+        /* get dll value */
+        add     r11, r11, #0x4          @ get addr of status reg
+        ldr     r10, [r11]              @ get locked value
+
+        /* voltage shift up */
+        mov r9, #0x0                    @ shift back to L0-voltage
+        bl voltage_shift                @ go raise voltage
+
+        /* frequency shift up */
+        mov     r3, #0x2                @ value for 2x operation
+        str     r3, [r2]                @ go to L0-freq operation
+
+        /* reset entry mode for dllctrl */
+        sub     r11, r11, #0x4          @ move from status to ctrl
+        cmp     r12, #0x1               @ normalize if cs1 based
+        subeq   r11, r11, #0x8          @ possibly back to DLLA
+        cmp     r8, #0x1                @ if forced unlock exit
+        orreq   r1, r1, #0x4            @ make sure exit with unlocked value
+        str     r1, [r11]               @ restore DLLA_CTRL high value
+        add     r11, r11, #0x8          @ move to DLLB_CTRL addr
+        str     r1, [r11]               @ set value DLLB_CTRL
+        bl      i_dll_wait              @ wait for possible lock
+
+        /* set up for return, DDR should be good */
+        str r10, [r0]                   @ write dll_status and return counter
+        ldmfd   sp!, {r0 - r12, pc}     @ restore regs and return
+
+        /* ensure the DLL has relocked */
+i_dll_wait:
+        mov     r4, #0x800              @ delay DLL relock, min 0x400 L3 clocks
+i_dll_delay:
+        subs    r4, r4, #0x1
+        bne     i_dll_delay
+        mov     pc, lr
+
+        /*
+         * shift up or down voltage, use R9 as input to tell level.
+         * wait for it to finish, use 32k sync counter, 1tick=31uS.
+         */
+voltage_shift:
+        ldr     r4, omap243x_sdi_prcm_voltctrl  @ get addr of volt ctrl.
+        ldr     r5, [r4]                @ get value.
+        ldr     r6, prcm_mask_val       @ get value of mask
+        and     r5, r5, r6              @ apply mask to clear bits
+        orr     r5, r5, r9              @ bulld value for L0/L1-volt operation.
+        str     r5, [r4]                @ set up for change.
+        mov     r3, #0x4000             @ get val for force
+        orr     r5, r5, r3              @ build value for force
+        str     r5, [r4]                @ Force transition to L1
+
+        ldr     r3, omap243x_sdi_timer_32ksynct_cr      @ get addr of counter
+        ldr     r5, [r3]                @ get value
+        add     r5, r5, #0x3            @ give it at most 93uS
+volt_delay:
+        ldr     r7, [r3]                @ get timer value
+        cmp     r5, r7                  @ time up?
+        bhi     volt_delay              @ not yet->branch
+        mov     pc, lr                  @ back to caller.
+
+omap243x_sdi_cm_clksel2_pll:
+        .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
+omap243x_sdi_sdrc_dlla_ctrl:
+        .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+omap243x_sdi_prcm_voltctrl:
+        .word OMAP243X_PRCM_VOLTCTRL
+prcm_mask_val:
+        .word 0xFFFF3FFC
+omap243x_sdi_timer_32ksynct_cr:
+        .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010)
+ENTRY(omap243x_sram_ddr_init_sz)
+        .word   . - omap243x_sram_ddr_init
+
+/*
+ * Reprograms memory timings.
+ * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR]
+ * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0
+ */
+ENTRY(omap243x_sram_reprogram_sdrc)
+        stmfd   sp!, {r0 - r10, lr}     @ save registers on stack
+        mov     r3, #0x0                @ clear for mrc call
+        mcr     p15, 0, r3, c7, c10, 4  @ memory barrier, finish ARM SDR/DDR
+        nop
+        nop
+        ldr     r6, omap243x_srs_sdrc_rfr_ctrl  @ get addr of refresh reg
+        ldr     r5, [r6]                @ get value
+        mov     r5, r5, lsr #8          @ isolate rfr field and drop burst
+
+        cmp     r0, #0x1                @ going to half speed?
+        movne   r9, #0x0                @ if up set flag up for pre up, hi volt
+
+        blne    voltage_shift_c         @ adjust voltage
+
+        cmp     r0, #0x1                @ going to half speed (post branch link)
+        moveq   r5, r5, lsr #1          @ divide by 2 if to half
+        movne   r5, r5, lsl #1          @ mult by 2 if to full
+        mov     r5, r5, lsl #8          @ put rfr field back into place
+        add     r5, r5, #0x1            @ turn on burst of 1
+        ldr     r4, omap243x_srs_cm_clksel2_pll @ get address of out reg
+        ldr     r3, [r4]                @ get curr value
+        orr     r3, r3, #0x3
+        bic     r3, r3, #0x3            @ clear lower bits
+        orr     r3, r3, r0              @ new state value
+        str     r3, [r4]                @ set new state (pll/x, x=1 or 2)
+        nop
+        nop
+
+        moveq   r9, #0x1                @ if speed down, post down, drop volt
+        bleq    voltage_shift_c
+
+        mcr     p15, 0, r3, c7, c10, 4  @ memory barrier
+        str     r5, [r6]                @ set new RFR_1 value
+        add     r6, r6, #0x30           @ get RFR_2 addr
+        str     r5, [r6]                @ set RFR_2
+        nop
+        cmp     r2, #0x1                @ (SDR or DDR) do we need to adjust DLL
+        bne     freq_out                @ leave if SDR, no DLL function
+
+        /* With DDR, we need to take care of the DLL for the frequency change */
+        ldr     r2, omap243x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl
+        str     r1, [r2]                @ write out new SDRC_DLLA_CTRL
+        add     r2, r2, #0x8            @ addr to SDRC_DLLB_CTRL
+        str     r1, [r2]                @ commit to SDRC_DLLB_CTRL
+        mov     r1, #0x2000             @ wait DLL relock, min 0x400 L3 clocks
+dll_wait:
+        subs    r1, r1, #0x1
+        bne     dll_wait
+freq_out:
+        ldmfd   sp!, {r0 - r10, pc}     @ restore regs and return
+
+    /*
+     * shift up or down voltage, use R9 as input to tell level.
+     *  wait for it to finish, use 32k sync counter, 1tick=31uS.
+     */
+voltage_shift_c:
+        ldr     r10, omap243x_srs_prcm_voltctrl @ get addr of volt ctrl
+        ldr     r8, [r10]               @ get value
+        ldr     r7, ddr_prcm_mask_val   @ get value of mask
+        and     r8, r8, r7              @ apply mask to clear bits
+        orr     r8, r8, r9              @ bulld value for L0/L1-volt operation.
+        str     r8, [r10]               @ set up for change.
+        mov     r7, #0x4000             @ get val for force
+        orr     r8, r8, r7              @ build value for force
+        str     r8, [r10]               @ Force transition to L1
+
+        ldr     r10, omap243x_srs_timer_32ksynct        @ get addr of counter
+        ldr     r8, [r10]               @ get value
+        add     r8, r8, #0x2            @ give it at most 62uS (min 31+)
+volt_delay_c:
+        ldr     r7, [r10]               @ get timer value
+        cmp     r8, r7                  @ time up?
+        bhi     volt_delay_c            @ not yet->branch
+        mov     pc, lr                  @ back to caller
+
+omap243x_srs_cm_clksel2_pll:
+        .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
+omap243x_srs_sdrc_dlla_ctrl:
+        .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+omap243x_srs_sdrc_rfr_ctrl:
+        .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
+omap243x_srs_prcm_voltctrl:
+        .word OMAP243X_PRCM_VOLTCTRL
+ddr_prcm_mask_val:
+        .word 0xFFFF3FFC
+omap243x_srs_timer_32ksynct:
+        .word IO_ADDRESS(OMAP2_32KSYNCT_BASE + 0x010)
+
+ENTRY(omap243x_sram_reprogram_sdrc_sz)
+        .word   . - omap243x_sram_reprogram_sdrc
+
+/*
+ * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode.
+ */
+ENTRY(omap243x_sram_set_prcm)
+        stmfd   sp!, {r0-r12, lr}       @ regs to stack
+        adr     r4, pbegin              @ addr of preload start
+        adr     r8, pend                @ addr of preload end
+        mcrr    p15, 1, r8, r4, c12     @ preload into icache
+pbegin:
+        /* move into fast relock bypass */
+        ldr     r8, omap243x_ssp_pll_ctl        @ get addr
+        ldr     r5, [r8]                @ get val
+        mvn     r6, #0x3                @ clear mask
+        and     r5, r5, r6              @ clear field
+        orr     r7, r5, #0x2            @ fast relock val
+        str     r7, [r8]                @ go to fast relock
+        ldr     r4, omap243x_ssp_pll_stat       @ addr of stat
+block:
+        /* wait for bypass */
+        ldr     r8, [r4]                @ stat value
+        and     r8, r8, #0x3            @ mask for stat
+        cmp     r8, #0x1                @ there yet
+        bne     block                   @ loop if not
+
+        /* set new dpll dividers _after_ in bypass */
+        ldr     r4, omap243x_ssp_pll_div        @ get addr
+        str     r0, [r4]                @ set dpll ctrl val
+
+        ldr     r4, omap243x_ssp_set_config     @ get addr
+        mov     r8, #1                  @ valid cfg msk
+        str     r8, [r4]                @ make dividers take
+
+        mov     r4, #100                @ dead spin a bit
+wait_a_bit:
+        subs    r4, r4, #1              @ dec loop
+        bne     wait_a_bit              @ delay done?
+
+        /* check if staying in bypass */
+        cmp     r2, #0x1                @ stay in bypass?
+        beq     pend                    @ jump over dpll relock
+
+        /* relock DPLL with new vals */
+        ldr     r5, omap243x_ssp_pll_stat       @ get addr
+        ldr     r4, omap243x_ssp_pll_ctl        @ get addr
+        orr     r8, r7, #0x3            @ val for lock dpll
+        str     r8, [r4]                @ set val
+        mov     r0, #1000               @ dead spin a bit
+wait_more:
+        subs    r0, r0, #1              @ dec loop
+        bne     wait_more               @ delay done?
+wait_lock:
+        ldr     r8, [r5]                @ get lock val
+        and     r8, r8, #3              @ isolate field
+        cmp     r8, #2                  @ locked?
+        bne     wait_lock               @ wait if not
+pend:
+        /* update memory timings & briefly lock dll */
+        ldr     r4, omap243x_ssp_sdrc_rfr       @ get addr
+        str     r1, [r4]                @ update refresh timing
+        ldr     r11, omap243x_ssp_dlla_ctrl     @ get addr of DLLA ctrl
+        ldr     r10, [r11]              @ get current val
+        mvn     r9, #0x4                @ mask to get clear bit2
+        and     r10, r10, r9            @ clear bit2 for lock mode
+        orr     r10, r10, #0x8          @ make sure DLL on (es2 bit pos)
+        str     r10, [r11]              @ commit to DLLA_CTRL
+        add     r11, r11, #0x8          @ move to dllb
+        str     r10, [r11]              @ hit DLLB also
+
+        mov     r4, #0x800              @ relock time (min 0x400 L3 clocks)
+wait_dll_lock:
+        subs    r4, r4, #0x1
+        bne     wait_dll_lock
+        nop
+        ldmfd   sp!, {r0-r12, pc}       @ restore regs and return
+
+omap243x_ssp_set_config:
+        .word OMAP243X_PRCM_CLKCFG_CTRL
+omap243x_ssp_pll_ctl:
+        .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKEN)
+omap243x_ssp_pll_stat:
+        .word OMAP2430_CM_REGADDR(PLL_MOD, CM_IDLEST)
+omap243x_ssp_pll_div:
+        .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL1)
+omap243x_ssp_sdrc_rfr:
+        .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
+omap243x_ssp_dlla_ctrl:
+        .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+
+ENTRY(omap243x_sram_set_prcm_sz)
+        .word   . - omap243x_sram_set_prcm
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 1f23f0459e5f..554ee58e1294 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -10,6 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#undef DEBUG
 
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -24,25 +25,43 @@
 #include <asm/arch/sram.h>
 #include <asm/arch/board.h>
 
+#include <asm/arch/control.h>
+
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+# include "../mach-omap2/prm.h"
+# include "../mach-omap2/cm.h"
+# include "../mach-omap2/sdrc.h"
+#endif
+
 #define OMAP1_SRAM_PA           0x20000000
-#define OMAP1_SRAM_VA           0xd0000000
+#define OMAP1_SRAM_VA           VMALLOC_END
 #define OMAP2_SRAM_PA           0x40200000
 #define OMAP2_SRAM_PUB_PA       0x4020f800
-#define OMAP2_SRAM_VA           0xd0000000
-#define OMAP2_SRAM_PUB_VA       0xd0000800
-
-#if defined(CONFIG_ARCH_OMAP24XX)
+#define OMAP2_SRAM_VA           VMALLOC_END
+#define OMAP2_SRAM_PUB_VA       (VMALLOC_END + 0x800)
+#define OMAP3_SRAM_PA           0x40200000
+#define OMAP3_SRAM_VA           0xd7000000
+#define OMAP3_SRAM_PUB_PA       0x40208000
+#define OMAP3_SRAM_PUB_VA       0xd7008000
+
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
 #define SRAM_BOOTLOADER_SZ      0x00
 #else
 #define SRAM_BOOTLOADER_SZ      0x80
 #endif
 
-#define VA_REQINFOPERM0         IO_ADDRESS(0x68005048)
-#define VA_READPERM0            IO_ADDRESS(0x68005050)
-#define VA_WRITEPERM0           IO_ADDRESS(0x68005058)
-#define VA_CONTROL_STAT         IO_ADDRESS(0x480002F8)
+#define OMAP24XX_VA_REQINFOPERM0        IO_ADDRESS(0x68005048)
+#define OMAP24XX_VA_READPERM0           IO_ADDRESS(0x68005050)
+#define OMAP24XX_VA_WRITEPERM0          IO_ADDRESS(0x68005058)
+
+#define OMAP34XX_VA_REQINFOPERM0        IO_ADDRESS(0x68012848)
+#define OMAP34XX_VA_READPERM0           IO_ADDRESS(0x68012850)
+#define OMAP34XX_VA_WRITEPERM0          IO_ADDRESS(0x68012858)
+#define OMAP34XX_VA_ADDR_MATCH2         IO_ADDRESS(0x68012880)
+#define OMAP34XX_VA_SMS_RG_ATT0         IO_ADDRESS(0x6C000048)
+#define OMAP34XX_VA_CONTROL_STAT        IO_ADDRESS(0x480022F0)
+
 #define GP_DEVICE               0x300
-#define TYPE_MASK               0x700
 
 #define ROUND_DOWN(value,boundary)      ((value) & (~((boundary)-1)))
 
@@ -68,14 +87,21 @@ static int is_sram_locked(void)
         int type = 0;
 
         if (cpu_is_omap242x())
-                type = __raw_readl(VA_CONTROL_STAT) & TYPE_MASK;
+                type = system_rev & OMAP2_DEVICETYPE_MASK;
 
         if (type == GP_DEVICE) {
                 /* RAMFW: R/W access to all initiators for all qualifier sets */
                 if (cpu_is_omap242x()) {
-                        __raw_writel(0xFF, VA_REQINFOPERM0); /* all q-vects */
-                        __raw_writel(0xCFDE, VA_READPERM0);  /* all i-read */
-                        __raw_writel(0xCFDE, VA_WRITEPERM0); /* all i-write */
+                        __raw_writel(0xFF, OMAP24XX_VA_REQINFOPERM0); /* all q-vects */
+                        __raw_writel(0xCFDE, OMAP24XX_VA_READPERM0);  /* all i-read */
+                        __raw_writel(0xCFDE, OMAP24XX_VA_WRITEPERM0); /* all i-write */
+                }
+                if (cpu_is_omap34xx()) {
+                        __raw_writel(0xFFFF, OMAP34XX_VA_REQINFOPERM0); /* all q-vects */
+                        __raw_writel(0xFFFF, OMAP34XX_VA_READPERM0);  /* all i-read */
+                        __raw_writel(0xFFFF, OMAP34XX_VA_WRITEPERM0); /* all i-write */
+                        __raw_writel(0x0, OMAP34XX_VA_ADDR_MATCH2);
+                        __raw_writel(0xFFFFFFFF, OMAP34XX_VA_SMS_RG_ATT0);
                 }
                 return 0;
         } else
@@ -92,18 +118,30 @@ void __init omap_detect_sram(void)
 {
         unsigned long reserved;
 
-        if (cpu_is_omap24xx()) {
+        if (cpu_class_is_omap2()) {
                 if (is_sram_locked()) {
-                        omap_sram_base = OMAP2_SRAM_PUB_VA;
-                        omap_sram_start = OMAP2_SRAM_PUB_PA;
-                        omap_sram_size = 0x800; /* 2K */
+                        if (cpu_is_omap34xx()) {
+                                omap_sram_base = OMAP3_SRAM_PUB_VA;
+                                omap_sram_start = OMAP3_SRAM_PUB_PA;
+                                omap_sram_size = 0x8000; /* 32K */
+                        } else {
+                                omap_sram_base = OMAP2_SRAM_PUB_VA;
+                                omap_sram_start = OMAP2_SRAM_PUB_PA;
+                                omap_sram_size = 0x800; /* 2K */
+                        }
                 } else {
-                        omap_sram_base = OMAP2_SRAM_VA;
-                        omap_sram_start = OMAP2_SRAM_PA;
-                        if (cpu_is_omap242x())
-                                omap_sram_size = 0xa0000; /* 640K */
-                        else if (cpu_is_omap243x())
+                        if (cpu_is_omap34xx()) {
+                                omap_sram_base = OMAP3_SRAM_VA;
+                                omap_sram_start = OMAP3_SRAM_PA;
                                 omap_sram_size = 0x10000; /* 64K */
+                        } else {
+                                omap_sram_base = OMAP2_SRAM_VA;
+                                omap_sram_start = OMAP2_SRAM_PA;
+                                if (cpu_is_omap242x())
+                                        omap_sram_size = 0xa0000; /* 640K */
+                                else if (cpu_is_omap243x())
+                                        omap_sram_size = 0x10000; /* 64K */
+                        }
                 }
         } else {
                 omap_sram_base = OMAP1_SRAM_VA;
@@ -157,6 +195,13 @@ void __init omap_map_sram(void)
                 omap_sram_io_desc[0].pfn = __phys_to_pfn(base);
         }
 
+        if (cpu_is_omap34xx()) {
+                omap_sram_io_desc[0].virtual = OMAP3_SRAM_VA;
+                base = OMAP3_SRAM_PA;
+                base = ROUND_DOWN(base, PAGE_SIZE);
+                omap_sram_io_desc[0].pfn = __phys_to_pfn(base);
+        }
+
         omap_sram_io_desc[0].length = 1024 * 1024;      /* Use section desc */
         iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc));
 
@@ -191,6 +236,7 @@ void * omap_sram_push(void * start, unsigned long size)
         omap_sram_ceil -= size;
         omap_sram_ceil = ROUND_DOWN(omap_sram_ceil, sizeof(void *));
         memcpy((void *)omap_sram_ceil, start, size);
+        flush_icache_range((unsigned long)start, (unsigned long)(start + size));
 
         return (void *)omap_sram_ceil;
 }
@@ -214,8 +260,9 @@ void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl)
 
 int __init omap1_sram_init(void)
 {
-        _omap_sram_reprogram_clock = omap_sram_push(sram_reprogram_clock,
-                                                    sram_reprogram_clock_sz);
+        _omap_sram_reprogram_clock =
+                        omap_sram_push(omap1_sram_reprogram_clock,
+                                        omap1_sram_reprogram_clock_sz);
 
         return 0;
 }
@@ -224,7 +271,7 @@ int __init omap1_sram_init(void)
 #define omap1_sram_init()       do {} while (0)
 #endif
 
-#ifdef CONFIG_ARCH_OMAP2
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
 
 static void (*_omap2_sram_ddr_init)(u32 *slow_dll_ctrl, u32 fast_dll_ctrl,
                               u32 base_cs, u32 force_unlock);
@@ -259,19 +306,109 @@ u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass)
 
         return _omap2_set_prcm(dpll_ctrl_val, sdrc_rfr_val, bypass);
 }
+#endif
+
+#ifdef CONFIG_ARCH_OMAP2420
+int __init omap242x_sram_init(void)
+{
+        _omap2_sram_ddr_init = omap_sram_push(omap242x_sram_ddr_init,
+                                        omap242x_sram_ddr_init_sz);
+
+        _omap2_sram_reprogram_sdrc = omap_sram_push(omap242x_sram_reprogram_sdrc,
+                                            omap242x_sram_reprogram_sdrc_sz);
+
+        _omap2_set_prcm = omap_sram_push(omap242x_sram_set_prcm,
+                                         omap242x_sram_set_prcm_sz);
+
+        return 0;
+}
+#else
+static inline int omap242x_sram_init(void)
+{
+        return 0;
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP2430
+int __init omap243x_sram_init(void)
+{
+        _omap2_sram_ddr_init = omap_sram_push(omap243x_sram_ddr_init,
+                                        omap243x_sram_ddr_init_sz);
+
+        _omap2_sram_reprogram_sdrc = omap_sram_push(omap243x_sram_reprogram_sdrc,
+                                            omap243x_sram_reprogram_sdrc_sz);
+
+        _omap2_set_prcm = omap_sram_push(omap243x_sram_set_prcm,
+                                         omap243x_sram_set_prcm_sz);
+
+        return 0;
+}
+#else
+static inline int omap243x_sram_init(void)
+{
+        return 0;
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP3
+
+static u32 (*_omap2_sram_reprogram_gpmc)(u32 perf_level);
+u32 omap2_sram_reprogram_gpmc(u32 perf_level)
+{
+        if (!_omap2_sram_reprogram_gpmc)
+                omap_sram_error();
+
+        return _omap2_sram_reprogram_gpmc(perf_level);
+}
+
+static u32 (*_omap2_sram_configure_core_dpll)(u32 m, u32 n,
+                                                u32 freqsel, u32 m2);
+u32 omap2_sram_configure_core_dpll(u32 m, u32 n, u32 freqsel, u32 m2)
+{
+        if (!_omap2_sram_configure_core_dpll)
+                omap_sram_error();
+
+        return _omap2_sram_configure_core_dpll(m, n, freqsel, m2);
+}
 
-int __init omap2_sram_init(void)
+/* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
+void restore_sram_functions(void)
 {
-        _omap2_sram_ddr_init = omap_sram_push(sram_ddr_init, sram_ddr_init_sz);
+        omap_sram_ceil = omap_sram_base + omap_sram_size;
 
-        _omap2_sram_reprogram_sdrc = omap_sram_push(sram_reprogram_sdrc,
-                                                    sram_reprogram_sdrc_sz);
-        _omap2_set_prcm = omap_sram_push(sram_set_prcm, sram_set_prcm_sz);
+        _omap2_sram_reprogram_gpmc = omap_sram_push(omap34xx_sram_reprogram_gpmc,
+                omap34xx_sram_reprogram_gpmc_sz);
+
+        _omap2_sram_configure_core_dpll =
+                        omap_sram_push(omap34xx_sram_configure_core_dpll,
+                                        omap34xx_sram_configure_core_dpll_sz);
+}
+
+int __init omap34xx_sram_init(void)
+{
+        _omap2_sram_ddr_init = omap_sram_push(omap34xx_sram_ddr_init,
+                                        omap34xx_sram_ddr_init_sz);
+
+        _omap2_sram_reprogram_sdrc = omap_sram_push(omap34xx_sram_reprogram_sdrc,
+                                        omap34xx_sram_reprogram_sdrc_sz);
+
+        _omap2_set_prcm = omap_sram_push(omap34xx_sram_set_prcm,
+                                        omap34xx_sram_set_prcm_sz);
+
+        _omap2_sram_reprogram_gpmc = omap_sram_push(omap34xx_sram_reprogram_gpmc,
+                                        omap34xx_sram_reprogram_gpmc_sz);
+
+        _omap2_sram_configure_core_dpll =
+                                omap_sram_push(omap34xx_sram_configure_core_dpll,
+                                        omap34xx_sram_configure_core_dpll_sz);
 
         return 0;
 }
 #else
-#define omap2_sram_init()       do {} while (0)
+static inline int omap34xx_sram_init(void)
+{
+        return 0;
+}
 #endif
 
 int __init omap_sram_init(void)
@@ -279,10 +416,14 @@ int __init omap_sram_init(void)
         omap_detect_sram();
         omap_map_sram();
 
-        if (!cpu_is_omap24xx())
+        if (!(cpu_class_is_omap2()))
                 omap1_sram_init();
-        else
-                omap2_sram_init();
+        else if (cpu_is_omap242x())
+                omap242x_sram_init();
+        else if (cpu_is_omap2430())
+                omap243x_sram_init();
+        else if (cpu_is_omap34xx())
+                omap34xx_sram_init();
 
         return 0;
 }