Merge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
  amba pl011: platform data for reg lockup and glitch v2
  amba pl011: workaround for uart registers lockup
  tty: n_gsm: improper skb_pull() use was leaking framed data
  tty: n_gsm: Fixed logic to decode break signal from modem status
  TTY: ntty, add one more sanity check
  TTY: ldisc, do not close until there are readers
  8250: Fix capabilities when changing the port type
  8250_pci: Fix missing const from merges
  ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
  serial: ioremap warning fix for jsm driver.
  8250_pci: add -ENODEV code for Intel EG20T PCH

4 files changed, 69 insertions, 4 deletions

diff --git a/arch/arm/mach-exynos4/init.c b/arch/arm/mach-exynos4/init.c
index cf91f50e43ab..a8a83e3881a4 100644
--- a/arch/arm/mach-exynos4/init.c
+++ b/arch/arm/mach-exynos4/init.c
@@ -35,6 +35,7 @@ void __init exynos4_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
                         tcfg->clocks = exynos4_serial_clocks;
                         tcfg->clocks_size = ARRAY_SIZE(exynos4_serial_clocks);
                 }
+                tcfg->flags |= NO_NEED_CHECK_CLKSRC;
         }
 
         s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index fd4cf1ca5efd..70cdbd60596a 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -110,10 +110,18 @@ static pin_cfg_t mop500_pins_common[] = {
         GPIO168_KP_O0,
 
         /* UART */
-        GPIO0_U0_CTSn   | PIN_INPUT_PULLUP,
-        GPIO1_U0_RTSn   | PIN_OUTPUT_HIGH,
-        GPIO2_U0_RXD    | PIN_INPUT_PULLUP,
-        GPIO3_U0_TXD    | PIN_OUTPUT_HIGH,
+        /* uart-0 pins gpio configuration should be
+         * kept intact to prevent glitch in tx line
+         * when tty dev is opened. Later these pins
+         * are configured to uart mop500_pins_uart0
+         *
+         * It will be replaced with uart configuration
+         * once the issue is solved.
+         */
+        GPIO0_GPIO      | PIN_INPUT_PULLUP,
+        GPIO1_GPIO      | PIN_OUTPUT_HIGH,
+        GPIO2_GPIO      | PIN_INPUT_PULLUP,
+        GPIO3_GPIO      | PIN_OUTPUT_HIGH,
 
         GPIO29_U2_RXD   | PIN_INPUT_PULLUP,
         GPIO30_U2_TXD   | PIN_OUTPUT_HIGH,
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index bb26f40493e6..2a08c07dec6d 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -27,18 +27,21 @@
 #include <linux/leds-lp5521.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
+#include <linux/delay.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
 #include <plat/i2c.h>
 #include <plat/ste_dma40.h>
+#include <plat/pincfg.h>
 
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
 #include <mach/irqs.h>
 
+#include "pins-db8500.h"
 #include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
 #include "board-mop500.h"
@@ -393,12 +396,63 @@ static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
 };
 #endif
 
+
+static pin_cfg_t mop500_pins_uart0[] = {
+        GPIO0_U0_CTSn   | PIN_INPUT_PULLUP,
+        GPIO1_U0_RTSn   | PIN_OUTPUT_HIGH,
+        GPIO2_U0_RXD    | PIN_INPUT_PULLUP,
+        GPIO3_U0_TXD    | PIN_OUTPUT_HIGH,
+};
+
+#define PRCC_K_SOFTRST_SET      0x18
+#define PRCC_K_SOFTRST_CLEAR    0x1C
+static void ux500_uart0_reset(void)
+{
+        void __iomem *prcc_rst_set, *prcc_rst_clr;
+
+        prcc_rst_set = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
+                        PRCC_K_SOFTRST_SET);
+        prcc_rst_clr = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
+                        PRCC_K_SOFTRST_CLEAR);
+
+        /* Activate soft reset PRCC_K_SOFTRST_CLEAR */
+        writel((readl(prcc_rst_clr) | 0x1), prcc_rst_clr);
+        udelay(1);
+
+        /* Release soft reset PRCC_K_SOFTRST_SET */
+        writel((readl(prcc_rst_set) | 0x1), prcc_rst_set);
+        udelay(1);
+}
+
+static void ux500_uart0_init(void)
+{
+        int ret;
+
+        ret = nmk_config_pins(mop500_pins_uart0,
+                        ARRAY_SIZE(mop500_pins_uart0));
+        if (ret < 0)
+                pr_err("pl011: uart pins_enable failed\n");
+}
+
+static void ux500_uart0_exit(void)
+{
+        int ret;
+
+        ret = nmk_config_pins_sleep(mop500_pins_uart0,
+                        ARRAY_SIZE(mop500_pins_uart0));
+        if (ret < 0)
+                pr_err("pl011: uart pins_disable failed\n");
+}
+
 static struct amba_pl011_data uart0_plat = {
 #ifdef CONFIG_STE_DMA40
         .dma_filter = stedma40_filter,
         .dma_rx_param = &uart0_dma_cfg_rx,
         .dma_tx_param = &uart0_dma_cfg_tx,
 #endif
+        .init = ux500_uart0_init,
+        .exit = ux500_uart0_exit,
+        .reset = ux500_uart0_reset,
 };
 
 static struct amba_pl011_data uart1_plat = {
diff --git a/arch/arm/plat-samsung/include/plat/regs-serial.h b/arch/arm/plat-samsung/include/plat/regs-serial.h
index c151c5f94a87..116edfe120b9 100644
--- a/arch/arm/plat-samsung/include/plat/regs-serial.h
+++ b/arch/arm/plat-samsung/include/plat/regs-serial.h
@@ -224,6 +224,8 @@
 #define S5PV210_UFSTAT_RXMASK   (255<<0)
 #define S5PV210_UFSTAT_RXSHIFT  (0)
 
+#define NO_NEED_CHECK_CLKSRC    1
+
 #ifndef __ASSEMBLY__
 
 /* struct s3c24xx_uart_clksrc