[ARM] S3C: Move plat-s3c24xx pm.c support into plat-s3c

Move parts of the core and debug suspend code into the
plat-s3c for use with the new s3c64xx code.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1 files changed, 211 insertions, 0 deletions

diff --git a/arch/arm/plat-s3c/pm.c b/arch/arm/plat-s3c/pm.c
index 122e9b91a7f4..fea58bea973d 100644
--- a/arch/arm/plat-s3c/pm.c
+++ b/arch/arm/plat-s3c/pm.c
@@ -15,14 +15,32 @@
 #include <linux/init.h>
 #include <linux/suspend.h>
 #include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/serial_core.h>
 #include <linux/io.h>
 
+#include <asm/cacheflush.h>
+#include <mach/hardware.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-irq.h>
+
 #include <plat/pm.h>
+#include <plat/pm-core.h>
 
 /* for external use */
 
 unsigned long s3c_pm_flags;
 
+/* Debug code:
+ *
+ * This code supports debug output to the low level UARTs for use on
+ * resume before the console layer is available.
+*/
+
 #ifdef CONFIG_S3C2410_PM_DEBUG
 extern void printascii(const char *);
 
@@ -37,8 +55,51 @@ void s3c_pm_dbg(const char *fmt, ...)
 
         printascii(buff);
 }
+
+static inline void s3c_pm_debug_init(void)
+{
+        /* restart uart clocks so we can use them to output */
+        s3c_pm_debug_init_uart();
+}
+
+#else
+#define s3c_pm_debug_init() do { } while(0)
+
 #endif /* CONFIG_S3C2410_PM_DEBUG */
 
+/* Save the UART configurations if we are configured for debug. */
+
+#ifdef CONFIG_S3C2410_PM_DEBUG
+
+#define SAVE_UART(va) \
+        SAVE_ITEM((va) + S3C2410_ULCON), \
+        SAVE_ITEM((va) + S3C2410_UCON), \
+        SAVE_ITEM((va) + S3C2410_UFCON), \
+        SAVE_ITEM((va) + S3C2410_UMCON), \
+        SAVE_ITEM((va) + S3C2410_UBRDIV)
+
+static struct sleep_save uart_save[] = {
+        SAVE_UART(S3C_VA_UART0),
+        SAVE_UART(S3C_VA_UART1),
+#ifndef CONFIG_CPU_S3C2400
+        SAVE_UART(S3C_VA_UART2),
+#endif
+};
+
+static void s3c_pm_save_uart(void)
+{
+        s3c_pm_do_save(uart_save, ARRAY_SIZE(uart_save));
+}
+
+static void s3c_pm_restore_uart(void)
+{
+        s3c_pm_do_restore(uart_save, ARRAY_SIZE(uart_save));
+}
+#else
+static void s3c_pm_save_uart(void) { }
+static void s3c_pm_restore_uart(void) { }
+#endif
+
 
 /* helper functions to save and restore register state */
 
@@ -95,3 +156,153 @@ void s3c_pm_do_restore_core(struct sleep_save *ptr, int count)
         for (; count > 0; count--, ptr++)
                 __raw_writel(ptr->val, ptr->reg);
 }
+
+/* s3c2410_pm_show_resume_irqs
+ *
+ * print any IRQs asserted at resume time (ie, we woke from)
+*/
+static void s3c_pm_show_resume_irqs(int start, unsigned long which,
+                                    unsigned long mask)
+{
+        int i;
+
+        which &= ~mask;
+
+        for (i = 0; i <= 31; i++) {
+                if (which & (1L<<i)) {
+                        S3C_PMDBG("IRQ %d asserted at resume\n", start+i);
+                }
+        }
+}
+
+
+void (*pm_cpu_prep)(void);
+void (*pm_cpu_sleep)(void);
+
+#define any_allowed(mask, allow) (((mask) & (allow)) != (allow))
+
+/* s3c_pm_enter
+ *
+ * central control for sleep/resume process
+*/
+
+static int s3c_pm_enter(suspend_state_t state)
+{
+        unsigned long regs_save[16];
+
+        /* ensure the debug is initialised (if enabled) */
+
+        s3c_pm_debug_init();
+
+        S3C_PMDBG("%s(%d)\n", __func__, state);
+
+        if (pm_cpu_prep == NULL || pm_cpu_sleep == NULL) {
+                printk(KERN_ERR "%s: error: no cpu sleep function\n", __func__);
+                return -EINVAL;
+        }
+
+        /* check if we have anything to wake-up with... bad things seem
+         * to happen if you suspend with no wakeup (system will often
+         * require a full power-cycle)
+        */
+
+        if (!any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
+            !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
+                printk(KERN_ERR "%s: No wake-up sources!\n", __func__);
+                printk(KERN_ERR "%s: Aborting sleep\n", __func__);
+                return -EINVAL;
+        }
+
+        /* prepare check area if configured */
+
+        s3c_pm_check_prepare();
+
+        /* store the physical address of the register recovery block */
+
+        s3c_sleep_save_phys = virt_to_phys(regs_save);
+
+        S3C_PMDBG("s3c_sleep_save_phys=0x%08lx\n", s3c_sleep_save_phys);
+
+        /* save all necessary core registers not covered by the drivers */
+
+        s3c_pm_save_gpios();
+        s3c_pm_save_uart();
+        s3c_pm_save_core();
+
+        /* set the irq configuration for wake */
+
+        s3c_pm_configure_extint();
+
+        S3C_PMDBG("sleep: irq wakeup masks: %08lx,%08lx\n",
+            s3c_irqwake_intmask, s3c_irqwake_eintmask);
+
+        s3c_pm_arch_prepare_irqs();
+
+        /* call cpu specific preparation */
+
+        pm_cpu_prep();
+
+        /* flush cache back to ram */
+
+        flush_cache_all();
+
+        s3c_pm_check_store();
+
+        /* send the cpu to sleep... */
+
+        s3c_pm_arch_stop_clocks();
+
+        /* s3c2410_cpu_save will also act as our return point from when
+         * we resume as it saves its own register state, so use the return
+         * code to differentiate return from save and return from sleep */
+
+        if (s3c2410_cpu_save(regs_save) == 0) {
+                flush_cache_all();
+                pm_cpu_sleep();
+        }
+
+        /* restore the cpu state using the kernel's cpu init code. */
+
+        cpu_init();
+
+        /* restore the system state */
+
+        s3c_pm_restore_core();
+        s3c_pm_restore_uart();
+        s3c_pm_restore_gpios();
+
+        s3c_pm_debug_init();
+
+        /* check what irq (if any) restored the system */
+
+        s3c_pm_arch_show_resume_irqs();
+
+        S3C_PMDBG("%s: post sleep, preparing to return\n", __func__);
+
+        s3c_pm_check_restore();
+
+        /* ok, let's return from sleep */
+
+        S3C_PMDBG("S3C PM Resume (post-restore)\n");
+        return 0;
+}
+
+static struct platform_suspend_ops s3c_pm_ops = {
+        .enter          = s3c_pm_enter,
+        .valid          = suspend_valid_only_mem,
+};
+
+/* s3c2410_pm_init
+ *
+ * Attach the power management functions. This should be called
+ * from the board specific initialisation if the board supports
+ * it.
+*/
+
+int __init s3c2410_pm_init(void)
+{
+        printk("S3C Power Management, Copyright 2004 Simtec Electronics\n");
+
+        suspend_set_ops(&s3c_pm_ops);
+        return 0;
+}