[ARM] 3597/1: ixp4xx/nslu2: Board support for new LED subsystem

Patch from Rod Whitby

This patch implements NEW_LEDS support for the Linksys NSLU2.  The
NSLU2 has four LED indicators, which are the only form of output for
an unmodified device - there is no keyboard or display on an NSLU2.
For an NSLU2 which has been modified to bring out the serial port
console, it is important to register that device first separately, to
enable debugging of other device support.

Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 47 insertions, 1 deletions

diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c
index 55411f21d838..749a337494d3 100644
--- a/arch/arm/mach-ixp4xx/nslu2-setup.c
+++ b/arch/arm/mach-ixp4xx/nslu2-setup.c
@@ -7,6 +7,7 @@
  *      Copyright (C) 2003-2004 MontaVista Software, Inc.
  *
  * Author: Mark Rakes <mrakes at mac.com>
+ * Author: Rod Whitby <rod@whitby.id.au>
  * Maintainers: http://www.nslu2-linux.org/
  *
  * Fixed missing init_time in MACHINE_START kas11 10/22/04
@@ -16,6 +17,7 @@
 #include <linux/kernel.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/leds.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -43,6 +45,42 @@ static struct ixp4xx_i2c_pins nslu2_i2c_gpio_pins = {
         .scl_pin                = NSLU2_SCL_PIN,
 };
 
+#ifdef CONFIG_LEDS_IXP4XX
+static struct resource nslu2_led_resources[] = {
+        {
+                .name           = "ready",  /* green led */
+                .start          = NSLU2_LED_GRN,
+                .end            = NSLU2_LED_GRN,
+                .flags          = IXP4XX_GPIO_HIGH,
+        },
+        {
+                .name           = "status", /* red led */
+                .start          = NSLU2_LED_RED,
+                .end            = NSLU2_LED_RED,
+                .flags          = IXP4XX_GPIO_HIGH,
+        },
+        {
+                .name           = "disk-1",
+                .start          = NSLU2_LED_DISK1,
+                .end            = NSLU2_LED_DISK1,
+                .flags          = IXP4XX_GPIO_LOW,
+        },
+        {
+                .name           = "disk-2",
+                .start          = NSLU2_LED_DISK2,
+                .end            = NSLU2_LED_DISK2,
+                .flags          = IXP4XX_GPIO_LOW,
+        },
+};
+
+static struct platform_device nslu2_leds = {
+        .name                   = "IXP4XX-GPIO-LED",
+        .id                     = -1,
+        .num_resources          = ARRAY_SIZE(nslu2_led_resources),
+        .resource               = nslu2_led_resources,
+};
+#endif
+
 static struct platform_device nslu2_i2c_controller = {
         .name                   = "IXP4XX-I2C",
         .id                     = 0,
@@ -102,8 +140,10 @@ static struct platform_device nslu2_uart = {
 static struct platform_device *nslu2_devices[] __initdata = {
         &nslu2_i2c_controller,
         &nslu2_flash,
-        &nslu2_uart,
         &nslu2_beeper,
+#ifdef CONFIG_LEDS_IXP4XX
+        &nslu2_leds,
+#endif
 };
 
 static void nslu2_power_off(void)
@@ -127,6 +167,12 @@ static void __init nslu2_init(void)
 
         pm_power_off = nslu2_power_off;
 
+        /* This is only useful on a modified machine, but it is valuable
+         * to have it first in order to see debug messages, and so that
+         * it does *not* get removed if platform_add_devices fails!
+         */
+        (void)platform_device_register(&nslu2_uart);
+
         platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
 }