USB: add USB-Persist facility

This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.

The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now.  But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

2 files changed, 147 insertions, 0 deletions

diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt
index 5b8d6953f05e..152b510d1bbb 100644
--- a/Documentation/power/swsusp.txt
+++ b/Documentation/power/swsusp.txt
@@ -393,6 +393,9 @@ safest thing is to unmount all filesystems on removable media (such USB,
 Firewire, CompactFlash, MMC, external SATA, or even IDE hotplug bays)
 before suspending; then remount them after resuming.
 
+There is a work-around for this problem.  For more information, see
+Documentation/usb/persist.txt.
+
 Q: I upgraded the kernel from 2.6.15 to 2.6.16. Both kernels were
 compiled with the similar configuration files. Anyway I found that
 suspend to disk (and resume) is much slower on 2.6.16 compared to
diff --git a/Documentation/usb/persist.txt b/Documentation/usb/persist.txt
new file mode 100644
index 000000000000..6dcd5f884795
--- /dev/null
+++ b/Documentation/usb/persist.txt
@@ -0,0 +1,144 @@
+                USB device persistence during system suspend
+
+                   Alan Stern <stern@rowland.harvard.edu>
+
+                 September 2, 2006 (Updated March 27, 2007)
+
+
+        What is the problem?
+
+According to the USB specification, when a USB bus is suspended the
+bus must continue to supply suspend current (around 1-5 mA).  This
+is so that devices can maintain their internal state and hubs can
+detect connect-change events (devices being plugged in or unplugged).
+The technical term is "power session".
+
+If a USB device's power session is interrupted then the system is
+required to behave as though the device has been unplugged.  It's a
+conservative approach; in the absence of suspend current the computer
+has no way to know what has actually happened.  Perhaps the same
+device is still attached or perhaps it was removed and a different
+device plugged into the port.  The system must assume the worst.
+
+By default, Linux behaves according to the spec.  If a USB host
+controller loses power during a system suspend, then when the system
+wakes up all the devices attached to that controller are treated as
+though they had disconnected.  This is always safe and it is the
+"officially correct" thing to do.
+
+For many sorts of devices this behavior doesn't matter in the least.
+If the kernel wants to believe that your USB keyboard was unplugged
+while the system was asleep and a new keyboard was plugged in when the
+system woke up, who cares?  It'll still work the same when you type on
+it.
+
+Unfortunately problems _can_ arise, particularly with mass-storage
+devices.  The effect is exactly the same as if the device really had
+been unplugged while the system was suspended.  If you had a mounted
+filesystem on the device, you're out of luck -- everything in that
+filesystem is now inaccessible.  This is especially annoying if your
+root filesystem was located on the device, since your system will
+instantly crash.
+
+Loss of power isn't the only mechanism to worry about.  Anything that
+interrupts a power session will have the same effect.  For example,
+even though suspend current may have been maintained while the system
+was asleep, on many systems during the initial stages of wakeup the
+firmware (i.e., the BIOS) resets the motherboard's USB host
+controllers.  Result: all the power sessions are destroyed and again
+it's as though you had unplugged all the USB devices.  Yes, it's
+entirely the BIOS's fault, but that doesn't do _you_ any good unless
+you can convince the BIOS supplier to fix the problem (lots of luck!).
+
+On many systems the USB host controllers will get reset after a
+suspend-to-RAM.  On almost all systems, no suspend current is
+available during suspend-to-disk (also known as swsusp).  You can
+check the kernel log after resuming to see if either of these has
+happened; look for lines saying "root hub lost power or was reset".
+
+In practice, people are forced to unmount any filesystems on a USB
+device before suspending.  If the root filesystem is on a USB device,
+the system can't be suspended at all.  (All right, it _can_ be
+suspended -- but it will crash as soon as it wakes up, which isn't
+much better.)
+
+
+        What is the solution?
+
+Setting CONFIG_USB_PERSIST will cause the kernel to work around these
+issues.  It enables a mode in which the core USB device data
+structures are allowed to persist across a power-session disruption.
+It works like this.  If the kernel sees that a USB host controller is
+not in the expected state during resume (i.e., if the controller was
+reset or otherwise had lost power) then it applies a persistence check
+to each of the USB devices below that controller.  It doesn't try to
+resume the device; that can't work once the power session is gone.
+Instead it issues a USB port reset and then re-enumerates the device.
+(This is exactly the same thing that happens whenever a USB device is
+reset.)  If the re-enumeration shows that the device now attached to
+that port has the same descriptors as before, including the Vendor and
+Product IDs, then the kernel continues to use the same device
+structure.  In effect, the kernel treats the device as though it had
+merely been reset instead of unplugged.
+
+If no device is now attached to the port, or if the descriptors are
+different from what the kernel remembers, then the treatment is what
+you would expect.  The kernel destroys the old device structure and
+behaves as though the old device had been unplugged and a new device
+plugged in, just as it would without the CONFIG_USB_PERSIST option.
+
+The end result is that the USB device remains available and usable.
+Filesystem mounts and memory mappings are unaffected, and the world is
+now a good and happy place.
+
+
+        Is this the best solution?
+
+Perhaps not.  Arguably, keeping track of mounted filesystems and
+memory mappings across device disconnects should be handled by a
+centralized Logical Volume Manager.  Such a solution would allow you
+to plug in a USB flash device, create a persistent volume associated
+with it, unplug the flash device, plug it back in later, and still
+have the same persistent volume associated with the device.  As such
+it would be more far-reaching than CONFIG_USB_PERSIST.
+
+On the other hand, writing a persistent volume manager would be a big
+job and using it would require significant input from the user.  This
+solution is much quicker and easier -- and it exists now, a giant
+point in its favor!
+
+Furthermore, the USB_PERSIST option applies to _all_ USB devices, not
+just mass-storage devices.  It might turn out to be equally useful for
+other device types, such as network interfaces.
+
+
+        WARNING: Using CONFIG_USB_PERSIST can be dangerous!!
+
+When recovering an interrupted power session the kernel does its best
+to make sure the USB device hasn't been changed; that is, the same
+device is still plugged into the port as before.  But the checks
+aren't guaranteed to be 100% accurate.
+
+If you replace one USB device with another of the same type (same
+manufacturer, same IDs, and so on) there's an excellent chance the
+kernel won't detect the change.  Serial numbers and other strings are
+not compared.  In many cases it wouldn't help if they were, because
+manufacturers frequently omit serial numbers entirely in their
+devices.
+
+Furthermore it's quite possible to leave a USB device exactly the same
+while changing its media.  If you replace the flash memory card in a
+USB card reader while the system is asleep, the kernel will have no
+way to know you did it.  The kernel will assume that nothing has
+happened and will continue to use the partition tables, inodes, and
+memory mappings for the old card.
+
+If the kernel gets fooled in this way, it's almost certain to cause
+data corruption and to crash your system.  You'll have no one to blame
+but yourself.
+
+YOU HAVE BEEN WARNED!  USE AT YOUR OWN RISK!
+
+That having been said, most of the time there shouldn't be any trouble
+at all.  The "persist" feature can be extremely useful.  Make the most
+of it.