Blackfin arch: add supporting for kgdb

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

1 files changed, 0 insertions, 155 deletions

diff --git a/Documentation/blackfin/kgdb.txt b/Documentation/blackfin/kgdb.txt
deleted file mode 100644
index 84f6a484ae9a..000000000000
--- a/Documentation/blackfin/kgdb.txt
+++ /dev/null
@@ -1,155 +0,0 @@
-                        A Simple Guide to Configure KGDB
-
-                        Sonic Zhang <sonic.zhang@analog.com>
-                                Aug. 24th 2006
-
-
-This KGDB patch enables the kernel developer to do source level debugging on
-the kernel for the Blackfin architecture.  The debugging works over either the
-ethernet interface or one of the uarts.  Both software breakpoints and
-hardware breakpoints are supported in this version.
-http://docs.blackfin.uclinux.org/doku.php?id=kgdb
-
-
-2 known issues:
-1. This bug:
-       http://blackfin.uclinux.org/tracker/index.php?func=detail&aid=544&group_id=18&atid=145
-   The GDB client for Blackfin uClinux causes incorrect values of local
-   variables to be displayed when the user breaks the running of kernel in GDB.
-2. Because of a hardware bug in Blackfin 533 v1.0.3:
-       05000067 - Watchpoints (Hardware Breakpoints) are not supported
-   Hardware breakpoints cannot be set properly.
-
-
-Debug over Ethernet:
- 
-1. Compile and install the cross platform version of gdb for blackfin, which
-   can be found at $(BINROOT)/bfin-elf-gdb.
-
-2. Apply this patch to the 2.6.x kernel.  Select the menuconfig option under
-   "Kernel hacking" -> "Kernel debugging" -> "KGDB: kernel debug with remote gdb".
-   With this selected, option "Full Symbolic/Source Debugging support" and 
-   "Compile the kernel with frame pointers" are also selected.
-
-3. Select option "KGDB: connect over (Ethernet)".  Add "kgdboe=@target-IP/,@host-IP/" to
-   the option "Compiled-in Kernel Boot Parameter" under "Kernel hacking".
-
-4. Connect minicom to the serial port and boot the kernel image.
-
-5. Configure the IP "/> ifconfig eth0 target-IP"
-
-6. Start GDB client "bfin-elf-gdb vmlinux".
-
-7. Connect to the target "(gdb) target remote udp:target-IP:6443".
-
-8. Set software breakpoint "(gdb) break sys_open".
-
-9. Continue "(gdb) c".
-
-10. Run ls in the target console "/> ls".
-
-11. Breakpoint hits. "Breakpoint 1: sys_open(..."
-
-12. Display local variables and function paramters.
-    (*) This operation gives wrong results, see known issue 1.
-
-13. Single stepping "(gdb) si".
-
-14. Remove breakpoint 1. "(gdb) del 1"
-
-15. Set hardware breakpoint "(gdb) hbreak sys_open".
-
-16. Continue "(gdb) c".
-
-17. Run ls in the target console "/> ls".
-
-18. Hardware breakpoint hits. "Breakpoint 1: sys_open(...".
-    (*) This hardware breakpoint will not be hit, see known issue 2.
-
-19. Continue "(gdb) c".
-
-20. Interrupt the target in GDB "Ctrl+C".
-
-21. Detach from the target "(gdb) detach".
-
-22. Exit GDB "(gdb) quit".
-
-
-Debug over the UART:
-
-1. Compile and install the cross platform version of gdb for blackfin, which
-   can be found at $(BINROOT)/bfin-elf-gdb.
-
-2. Apply this patch to the 2.6.x kernel.  Select the menuconfig option under
-   "Kernel hacking" -> "Kernel debugging" -> "KGDB: kernel debug with remote gdb".
-   With this selected, option "Full Symbolic/Source Debugging support" and 
-   "Compile the kernel with frame pointers" are also selected.
-
-3. Select option "KGDB: connect over (UART)".  Set "KGDB: UART port number" to be
-   a different one from the console.  Don't forget to change the mode of
-   blackfin serial driver to PIO.  Otherwise kgdb works incorrectly on UART.
- 
-4. If you want connect to kgdb when the kernel boots, enable
-   "KGDB: Wait for gdb connection early" 
-
-5. Compile kernel.
-
-6. Connect minicom to the serial port of the console and boot the kernel image.
-
-7. Start GDB client "bfin-elf-gdb vmlinux".
-
-8. Set the baud rate in GDB "(gdb) set remotebaud 57600".
-
-9. Connect to the target on the second serial port "(gdb) target remote /dev/ttyS1".
-
-10. Set software breakpoint "(gdb) break sys_open".
-
-11. Continue "(gdb) c". 
-
-12. Run ls in the target console "/> ls". 
-
-13. A breakpoint is hit. "Breakpoint 1: sys_open(..."
-
-14. All other operations are the same as that in KGDB over Ethernet. 
-
-
-Debug over the same UART as console:
-
-1. Compile and install the cross platform version of gdb for blackfin, which
-   can be found at $(BINROOT)/bfin-elf-gdb.
-
-2. Apply this patch to the 2.6.x kernel.  Select the menuconfig option under
-   "Kernel hacking" -> "Kernel debugging" -> "KGDB: kernel debug with remote gdb".
-   With this selected, option "Full Symbolic/Source Debugging support" and 
-   "Compile the kernel with frame pointers" are also selected.
-
-3. Select option "KGDB: connect over UART".  Set "KGDB: UART port number" to console.
-   Don't forget to change the mode of blackfin serial driver to PIO.
-   Otherwise kgdb works incorrectly on UART.
- 
-4. If you want connect to kgdb when the kernel boots, enable
-   "KGDB: Wait for gdb connection early" 
-
-5. Connect minicom to the serial port and boot the kernel image. 
-
-6. (Optional) Ask target to wait for gdb connection by entering Ctrl+A. In minicom, you should enter Ctrl+A+A.
-
-7. Start GDB client "bfin-elf-gdb vmlinux".
-
-8. Set the baud rate in GDB "(gdb) set remotebaud 57600".
-
-9. Connect to the target "(gdb) target remote /dev/ttyS0".
-
-10. Set software breakpoint "(gdb) break sys_open".
-
-11. Continue "(gdb) c". Then enter Ctrl+C twice to stop GDB connection.
-
-12. Run ls in the target console "/> ls". Dummy string can be seen on the console.
-
-13. Then connect the gdb to target again. "(gdb) target remote /dev/ttyS0".
-    Now you will find a breakpoint is hit. "Breakpoint 1: sys_open(..."
-
-14. All other operations are the same as that in KGDB over Ethernet.  The only
-    difference is that after continue command in GDB, please stop GDB
-    connection by 2 "Ctrl+C"s and connect again after breakpoints are hit or
-    Ctrl+A is entered.