Merge commit 'v2.6.30-rc5' into next

8 files changed, 246 insertions, 62 deletions

diff --git a/Documentation/hwmon/ds1621 b/Documentation/hwmon/ds1621
index 1fee6f1e6bc5..5e97f333c4df 100644
--- a/Documentation/hwmon/ds1621
+++ b/Documentation/hwmon/ds1621
@@ -49,12 +49,9 @@ of up to +/- 0.5 degrees even when compared against precise temperature
 readings. Be sure to have a high vs. low temperature limit gap of al least
 1.0 degree Celsius to avoid Tout "bouncing", though!
 
-As for alarms, you can read the alarm status of the DS1621 via the 'alarms'
-/sys file interface. The result consists mainly of bit 6 and 5 of the
-configuration register of the chip; bit 6 (0x40 or 64) is the high alarm
-bit and bit 5 (0x20 or 32) the low one. These bits are set when the high or
-low limits are met or exceeded and are reset by the module as soon as the
-respective temperature ranges are left.
+The alarm bits are set when the high or low limits are met or exceeded and
+are reset by the module as soon as the respective temperature ranges are
+left.
 
 The alarm registers are in no way suitable to find out about the actual
 status of Tout. They will only tell you about its history, whether or not
@@ -64,45 +61,3 @@ with neither of the alarms set.
 
 Temperature conversion of the DS1621 takes up to 1000ms; internal access to
 non-volatile registers may last for 10ms or below.
-
-High Accuracy Temperature Reading
----------------------------------
-
-As said before, the temperature issued via the 9-bit i2c-bus data is
-somewhat arbitrary. Internally, the temperature conversion is of a
-different kind that is explained (not so...) well in the DS1621 data sheet.
-To cut the long story short: Inside the DS1621 there are two oscillators,
-both of them biassed by a temperature coefficient.
-
-Higher resolution of the temperature reading can be achieved using the
-internal projection, which means taking account of REG_COUNT and REG_SLOPE
-(the driver manages them):
-
-Taken from Dallas Semiconductors App Note 068: 'Increasing Temperature
-Resolution on the DS1620' and App Note 105: 'High Resolution Temperature
-Measurement with Dallas Direct-to-Digital Temperature Sensors'
-
-- Read the 9-bit temperature and strip the LSB (Truncate the .5 degs)
-- The resulting value is TEMP_READ.
-- Then, read REG_COUNT.
-- And then, REG_SLOPE.
-
-      TEMP = TEMP_READ - 0.25 + ((REG_SLOPE - REG_COUNT) / REG_SLOPE)
-
-Note that this is what the DONE bit in the DS1621 configuration register is
-good for: Internally, one temperature conversion takes up to 1000ms. Before
-that conversion is complete you will not be able to read valid things out
-of REG_COUNT and REG_SLOPE. The DONE bit, as you may have guessed by now,
-tells you whether the conversion is complete ("done", in plain English) and
-thus, whether the values you read are good or not.
-
-The DS1621 has two modes of operation: "Continuous" conversion, which can
-be understood as the default stand-alone mode where the chip gets the
-temperature and controls external devices via its Tout pin or tells other
-i2c's about it if they care. The other mode is called "1SHOT", that means
-that it only figures out about the temperature when it is explicitly told
-to do so; this can be seen as power saving mode.
-
-Now if you want to read REG_COUNT and REG_SLOPE, you have to either stop
-the continuous conversions until the contents of these registers are valid,
-or, in 1SHOT mode, you have to have one conversion made.
diff --git a/Documentation/hwmon/g760a b/Documentation/hwmon/g760a
new file mode 100644
index 000000000000..e032eeb75629
--- /dev/null
+++ b/Documentation/hwmon/g760a
@@ -0,0 +1,36 @@
+Kernel driver g760a
+===================
+
+Supported chips:
+  * Global Mixed-mode Technology Inc. G760A
+    Prefix: 'g760a'
+    Datasheet: Publicly available at the GMT website
+      http://www.gmt.com.tw/datasheet/g760a.pdf
+
+Author: Herbert Valerio Riedel <hvr@gnu.org>
+
+Description
+-----------
+
+The GMT G760A Fan Speed PWM Controller is connected directly to a fan
+and performs closed-loop control of the fan speed.
+
+The fan speed is programmed by setting the period via 'pwm1' of two
+consecutive speed pulses. The period is defined in terms of clock
+cycle counts of an assumed 32kHz clock source.
+
+Setting a period of 0 stops the fan; setting the period to 255 sets
+fan to maximum speed.
+
+The measured fan rotation speed returned via 'fan1_input' is derived
+from the measured speed pulse period by assuming again a 32kHz clock
+source and a 2 pulse-per-revolution fan.
+
+The 'alarms' file provides access to the two alarm bits provided by
+the G760A chip's status register: Bit 0 is set when the actual fan
+speed differs more than 20% with respect to the programmed fan speed;
+bit 1 is set when fan speed is below 1920 RPM.
+
+The g760a driver will not update its values more frequently than every
+other second; reading them more often will do no harm, but will return
+'old' values.
diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d
index 287f8c902656..effe949a7282 100644
--- a/Documentation/hwmon/lis3lv02d
+++ b/Documentation/hwmon/lis3lv02d
@@ -1,11 +1,11 @@
 Kernel driver lis3lv02d
-==================
+=======================
 
 Supported chips:
 
   * STMicroelectronics LIS3LV02DL and LIS3LV02DQ
 
-Author:
+Authors:
         Yan Burman <burman.yan@gmail.com>
         Eric Piel <eric.piel@tremplin-utc.net>
 
@@ -15,7 +15,7 @@ Description
 
 This driver provides support for the accelerometer found in various HP
 laptops sporting the feature officially called "HP Mobile Data
-Protection System 3D" or "HP 3D DriveGuard". It detect automatically
+Protection System 3D" or "HP 3D DriveGuard". It detects automatically
 laptops with this sensor. Known models (for now the HP 2133, nc6420,
 nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis
 automatically oriented on standard way (eg: you can directly play
@@ -27,7 +27,7 @@ position - 3D position that the accelerometer reports. Format: "(x,y,z)"
 calibrate - read: values (x, y, z) that are used as the base for input
                   class device operation.
             write: forces the base to be recalibrated with the current
-                  position.
+                   position.
 rate - reports the sampling rate of the accelerometer device in HZ
 
 This driver also provides an absolute input class device, allowing
@@ -48,7 +48,7 @@ For better compatibility between the various laptops. The values reported by
 the accelerometer are converted into a "standard" organisation of the axes
 (aka "can play neverball out of the box"):
  * When the laptop is horizontal the position reported is about 0 for X and Y
-and a positive value for Z
+        and a positive value for Z
  * If the left side is elevated, X increases (becomes positive)
  * If the front side (where the touchpad is) is elevated, Y decreases
         (becomes negative)
@@ -59,3 +59,13 @@ email to the authors to add it to the database.  When reporting a new
 laptop, please include the output of "dmidecode" plus the value of
 /sys/devices/platform/lis3lv02d/position in these four cases.
 
+Q&A
+---
+
+Q: How do I safely simulate freefall? I have an HP "portable
+workstation" which has about 3.5kg and a plastic case, so letting it
+fall to the ground is out of question...
+
+A: The sensor is pretty sensitive, so your hands can do it. Lift it
+into free space, follow the fall with your hands for like 10
+centimeters. That should be enough to trigger the detection.
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90
index 0e8411710238..93d8e3d55150 100644
--- a/Documentation/hwmon/lm90
+++ b/Documentation/hwmon/lm90
@@ -42,6 +42,11 @@ Supported chips:
     Addresses scanned: I2C 0x4e
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497
+  * Maxim MAX6648
+    Prefix: 'max6646'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500
   * Maxim MAX6649
     Prefix: 'max6646'
     Addresses scanned: I2C 0x4c
@@ -74,6 +79,11 @@ Supported chips:
                            0x4c, 0x4d and 0x4e
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370
+  * Maxim MAX6692
+    Prefix: 'max6646'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500
 
 
 Author: Jean Delvare <khali@linux-fr.org>
diff --git a/Documentation/hwmon/ltc4215 b/Documentation/hwmon/ltc4215
new file mode 100644
index 000000000000..2e6a21eb656c
--- /dev/null
+++ b/Documentation/hwmon/ltc4215
@@ -0,0 +1,50 @@
+Kernel driver ltc4215
+=====================
+
+Supported chips:
+  * Linear Technology LTC4215
+    Prefix: 'ltc4215'
+    Addresses scanned: 0x44
+    Datasheet:
+        http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1163,P17572,D12697
+
+Author: Ira W. Snyder <iws@ovro.caltech.edu>
+
+
+Description
+-----------
+
+The LTC4215 controller allows a board to be safely inserted and removed
+from a live backplane.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4215 devices, due to the fact that some
+of the possible addresses are unfriendly to probing. You will need to use
+the "force" parameter to tell the driver where to find the device.
+
+Example: the following will load the driver for an LTC4215 at address 0x44
+on I2C bus #0:
+$ modprobe ltc4215 force=0,0x44
+
+
+Sysfs entries
+-------------
+
+The LTC4215 has built-in limits for overvoltage, undervoltage, and
+undercurrent warnings. This makes it very likely that the reference
+circuit will be used.
+
+in1_input               input voltage
+in2_input               output voltage
+
+in1_min_alarm           input undervoltage alarm
+in1_max_alarm           input overvoltage alarm
+
+curr1_input             current
+curr1_max_alarm         overcurrent alarm
+
+power1_input            power usage
+power1_alarm            power bad alarm
diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591
new file mode 100644
index 000000000000..5628fcf4207f
--- /dev/null
+++ b/Documentation/hwmon/pcf8591
@@ -0,0 +1,90 @@
+Kernel driver pcf8591
+=====================
+
+Supported chips:
+  * Philips PCF8591
+    Prefix: 'pcf8591'
+    Addresses scanned: I2C 0x48 - 0x4f
+    Datasheet: Publicly available at the Philips Semiconductor website
+               http://www.semiconductors.philips.com/pip/PCF8591P.html
+
+Authors:
+        Aurelien Jarno <aurelien@aurel32.net>
+        valuable contributions by Jan M. Sendler <sendler@sendler.de>,
+        Jean Delvare <khali@linux-fr.org>
+
+
+Description
+-----------
+The PCF8591 is an 8-bit A/D and D/A converter (4 analog inputs and one
+analog output) for the I2C bus produced by Philips Semiconductors. It
+is designed to provide a byte I2C interface to up to 4 separate devices.
+
+The PCF8591 has 4 analog inputs programmable as single-ended or
+differential inputs :
+- mode 0 : four single ended inputs
+        Pins AIN0 to AIN3 are single ended inputs for channels 0 to 3
+
+- mode 1 : three differential inputs
+        Pins AIN3 is the common negative differential input
+        Pins AIN0 to AIN2 are positive differential inputs for channels 0 to 2
+
+- mode 2 : single ended and differential mixed
+        Pins AIN0 and AIN1 are single ended inputs for channels 0 and 1
+        Pins AIN2 is the positive differential input for channel 3
+        Pins AIN3 is the negative differential input for channel 3
+
+- mode 3 : two differential inputs
+        Pins AIN0 is the positive differential input for channel 0
+        Pins AIN1 is the negative differential input for channel 0
+        Pins AIN2 is the positive differential input for channel 1
+        Pins AIN3 is the negative differential input for channel 1
+
+See the datasheet for details.
+
+Module parameters
+-----------------
+
+* input_mode int
+
+    Analog input mode:
+         0 = four single ended inputs
+         1 = three differential inputs
+         2 = single ended and differential mixed
+         3 = two differential inputs
+
+
+Accessing PCF8591 via /sys interface
+-------------------------------------
+
+! Be careful !
+The PCF8591 is plainly impossible to detect ! Stupid chip.
+So every chip with address in the interval [48..4f] is
+detected as PCF8591. If you have other chips in this address
+range, the workaround is to load this module after the one
+for your others chips.
+
+On detection (i.e. insmod, modprobe et al.), directories are being
+created for each detected PCF8591:
+
+/sys/bus/devices/<0>-<1>/
+where <0> is the bus the chip was detected on (e. g. i2c-0)
+and <1> the chip address ([48..4f])
+
+Inside these directories, there are such files:
+in0, in1, in2, in3, out0_enable, out0_output, name
+
+Name contains chip name.
+
+The in0, in1, in2 and in3 files are RO. Reading gives the value of the
+corresponding channel. Depending on the current analog inputs configuration,
+files in2 and/or in3 do not exist. Values range are from 0 to 255 for single
+ended inputs and -128 to +127 for differential inputs (8-bit ADC).
+
+The out0_enable file is RW. Reading gives "1" for analog output enabled and
+"0" for analog output disabled. Writing accepts "0" and "1" accordingly.
+
+The out0_output file is RW. Writing a number between 0 and 255 (8-bit DAC), send
+the value to the digital-to-analog converter. Note that a voltage will
+only appears on AOUT pin if aout0_enable equals 1. Reading returns the last
+value written.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index 6dbfd5efd991..2f10ce6a879f 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -365,6 +365,7 @@ energy[1-*]_input		Cumulative energy use
                                 Unit: microJoule
                                 RO
 
+
 **********
 * Alarms *
 **********
@@ -453,6 +454,27 @@ beep_mask	Bitmask for beep.
                 RW
 
 
+***********************
+* Intrusion detection *
+***********************
+
+intrusion[0-*]_alarm
+                Chassis intrusion detection
+                0: OK
+                1: intrusion detected
+                RW
+                Contrary to regular alarm flags which clear themselves
+                automatically when read, this one sticks until cleared by
+                the user. This is done by writing 0 to the file. Writing
+                other values is unsupported.
+
+intrusion[0-*]_beep
+                Chassis intrusion beep
+                0: disable
+                1: enable
+                RW
+
+
 sysfs attribute writes interpretation
 -------------------------------------
 
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index d6e1ae30fa6e..b6eb59384bb3 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -2,30 +2,40 @@ Kernel driver w83627ehf
 =======================
 
 Supported chips:
-  * Winbond W83627EHF/EHG/DHG (ISA access ONLY)
+  * Winbond W83627EHF/EHG (ISA access ONLY)
     Prefix: 'w83627ehf'
     Addresses scanned: ISA address retrieved from Super I/O registers
     Datasheet:
-        http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf
-        DHG datasheet confidential.
+        http://www.nuvoton.com.tw/NR/rdonlyres/A6A258F0-F0C9-4F97-81C0-C4D29E7E943E/0/W83627EHF.pdf
+  * Winbond W83627DHG
+    Prefix: 'w83627dhg'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet:
+        http://www.nuvoton.com.tw/NR/rdonlyres/7885623D-A487-4CF9-A47F-30C5F73D6FE6/0/W83627DHG.pdf
+  * Winbond W83667HG
+    Prefix: 'w83667hg'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet: not available
 
 Authors:
         Jean Delvare <khali@linux-fr.org>
         Yuan Mu (Winbond)
         Rudolf Marek <r.marek@assembler.cz>
         David Hubbard <david.c.hubbard@gmail.com>
+        Gong Jun <JGong@nuvoton.com>
 
 Description
 -----------
 
-This driver implements support for the Winbond W83627EHF, W83627EHG, and
-W83627DHG super I/O chips. We will refer to them collectively as Winbond chips.
+This driver implements support for the Winbond W83627EHF, W83627EHG,
+W83627DHG and W83667HG super I/O chips. We will refer to them collectively
+as Winbond chips.
 
 The chips implement three temperature sensors, five fan rotation
 speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
-VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG), alarms with beep
-warnings (control unimplemented), and some automatic fan regulation
-strategies (plus manual fan control mode).
+VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms
+with beep warnings (control unimplemented), and some automatic fan
+regulation strategies (plus manual fan control mode).
 
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
@@ -54,7 +64,8 @@ follows:
 temp1 -> pwm1
 temp2 -> pwm2
 temp3 -> pwm3
-prog  -> pwm4 (the programmable setting is not supported by the driver)
+prog  -> pwm4 (not on 667HG; the programmable setting is not supported by
+               the driver)
 
 /sys files
 ----------