Create/use more directory structure in the Documentation/ tree.

Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>

1 files changed, 0 insertions, 245 deletions

diff --git a/Documentation/floppy.txt b/Documentation/floppy.txt
deleted file mode 100644
index 6ccab88705cb..000000000000
--- a/Documentation/floppy.txt
+++ /dev/null
@@ -1,245 +0,0 @@
-This file describes the floppy driver.
-
-FAQ list:
-=========
-
- A FAQ list may be found in the fdutils package (see below), and also
-at <http://fdutils.linux.lu/faq.html>.
-
-
-LILO configuration options (Thinkpad users, read this)
-======================================================
-
- The floppy driver is configured using the 'floppy=' option in
-lilo. This option can be typed at the boot prompt, or entered in the
-lilo configuration file.
-
- Example: If your kernel is called linux-2.6.9, type the following line
-at the lilo boot prompt (if you have a thinkpad):
-
- linux-2.6.9 floppy=thinkpad
-
-You may also enter the following line in /etc/lilo.conf, in the description
-of linux-2.6.9:
-
- append = "floppy=thinkpad"
-
- Several floppy related options may be given, example:
-
- linux-2.6.9 floppy=daring floppy=two_fdc
- append = "floppy=daring floppy=two_fdc"
-
- If you give options both in the lilo config file and on the boot
-prompt, the option strings of both places are concatenated, the boot
-prompt options coming last. That's why there are also options to
-restore the default behavior.
-
-
-Module configuration options
-============================
-
- If you use the floppy driver as a module, use the following syntax:
-modprobe floppy <options>
-
-Example:
- modprobe floppy omnibook messages
-
- If you need certain options enabled every time you load the floppy driver,
-you can put:
-
- options floppy omnibook messages
-
-in /etc/modprobe.conf.
-
-
- The floppy driver related options are:
-
- floppy=asus_pci
-        Sets the bit mask to allow only units 0 and 1. (default)
-
- floppy=daring
-        Tells the floppy driver that you have a well behaved floppy controller.
-        This allows more efficient and smoother operation, but may fail on
-        certain controllers. This may speed up certain operations.
-
- floppy=0,daring
-        Tells the floppy driver that your floppy controller should be used
-        with caution.
-
- floppy=one_fdc
-        Tells the floppy driver that you have only one floppy controller.
-        (default)
-
- floppy=two_fdc
- floppy=<address>,two_fdc
-        Tells the floppy driver that you have two floppy controllers.
-        The second floppy controller is assumed to be at <address>.
-        This option is not needed if the second controller is at address
-        0x370, and if you use the 'cmos' option.
-
- floppy=thinkpad
-        Tells the floppy driver that you have a Thinkpad. Thinkpads use an
-        inverted convention for the disk change line.
-
- floppy=0,thinkpad
-        Tells the floppy driver that you don't have a Thinkpad.
-
- floppy=omnibook
- floppy=nodma
-        Tells the floppy driver not to use Dma for data transfers.
-        This is needed on HP Omnibooks, which don't have a workable
-        DMA channel for the floppy driver. This option is also useful
-        if you frequently get "Unable to allocate DMA memory" messages.
-        Indeed, dma memory needs to be continuous in physical memory,
-        and is thus harder to find, whereas non-dma buffers may be
-        allocated in virtual memory. However, I advise against this if
-        you have an FDC without a FIFO (8272A or 82072). 82072A and
-        later are OK. You also need at least a 486 to use nodma.
-        If you use nodma mode, I suggest you also set the FIFO
-        threshold to 10 or lower, in order to limit the number of data
-        transfer interrupts.
-
-        If you have a FIFO-able FDC, the floppy driver automatically
-        falls back on non DMA mode if no DMA-able memory can be found.
-        If you want to avoid this, explicitly ask for 'yesdma'.
-
- floppy=yesdma
-        Tells the floppy driver that a workable DMA channel is available.
-        (default)
-
- floppy=nofifo
-        Disables the FIFO entirely. This is needed if you get "Bus
-        master arbitration error" messages from your Ethernet card (or
-        from other devices) while accessing the floppy.
-
- floppy=usefifo
-        Enables the FIFO. (default)
-
- floppy=<threshold>,fifo_depth
-        Sets the FIFO threshold. This is mostly relevant in DMA
-        mode. If this is higher, the floppy driver tolerates more
-        interrupt latency, but it triggers more interrupts (i.e. it
-        imposes more load on the rest of the system). If this is
-        lower, the interrupt latency should be lower too (faster
-        processor). The benefit of a lower threshold is less
-        interrupts.
-
-        To tune the fifo threshold, switch on over/underrun messages
-        using 'floppycontrol --messages'. Then access a floppy
-        disk. If you get a huge amount of "Over/Underrun - retrying"
-        messages, then the fifo threshold is too low. Try with a
-        higher value, until you only get an occasional Over/Underrun.
-        It is a good idea to compile the floppy driver as a module
-        when doing this tuning. Indeed, it allows to try different
-        fifo values without rebooting the machine for each test. Note
-        that you need to do 'floppycontrol --messages' every time you
-        re-insert the module.
-
-        Usually, tuning the fifo threshold should not be needed, as
-        the default (0xa) is reasonable.
-
- floppy=<drive>,<type>,cmos
-        Sets the CMOS type of <drive> to <type>. This is mandatory if
-        you have more than two floppy drives (only two can be
-        described in the physical CMOS), or if your BIOS uses
-        non-standard CMOS types. The CMOS types are:
-
-                0 - Use the value of the physical CMOS
-                1 - 5 1/4 DD
-                2 - 5 1/4 HD
-                3 - 3 1/2 DD
-                4 - 3 1/2 HD
-                5 - 3 1/2 ED
-                6 - 3 1/2 ED
-               16 - unknown or not installed
-
-        (Note: there are two valid types for ED drives. This is because 5 was
-        initially chosen to represent floppy *tapes*, and 6 for ED drives.
-        AMI ignored this, and used 5 for ED drives. That's why the floppy
-        driver handles both.)
-
- floppy=unexpected_interrupts
-        Print a warning message when an unexpected interrupt is received.
-        (default)
-
- floppy=no_unexpected_interrupts
- floppy=L40SX
-        Don't print a message when an unexpected interrupt is received. This
-        is needed on IBM L40SX laptops in certain video modes. (There seems
-        to be an interaction between video and floppy. The unexpected
-        interrupts affect only performance, and can be safely ignored.)
-
- floppy=broken_dcl
-        Don't use the disk change line, but assume that the disk was
-        changed whenever the device node is reopened. Needed on some
-        boxes where the disk change line is broken or unsupported.
-        This should be regarded as a stopgap measure, indeed it makes
-        floppy operation less efficient due to unneeded cache
-        flushings, and slightly more unreliable. Please verify your
-        cable, connection and jumper settings if you have any DCL
-        problems. However, some older drives, and also some laptops
-        are known not to have a DCL.
-
- floppy=debug
-        Print debugging messages.
-
- floppy=messages
-        Print informational messages for some operations (disk change
-        notifications, warnings about over and underruns, and about
-        autodetection).
-
- floppy=silent_dcl_clear
-        Uses a less noisy way to clear the disk change line (which
-        doesn't involve seeks). Implied by 'daring' option.
-
- floppy=<nr>,irq
-        Sets the floppy IRQ to <nr> instead of 6.
-
- floppy=<nr>,dma
-        Sets the floppy DMA channel to <nr> instead of 2.
-
- floppy=slow
-        Use PS/2 stepping rate:
-         " PS/2 floppies have much slower step rates than regular floppies.
-           It's been recommended that take about 1/4 of the default speed
-           in some more extreme cases."
-
-
-Supporting utilities and additional documentation:
-==================================================
-
- Additional parameters of the floppy driver can be configured at
-runtime. Utilities which do this can be found in the fdutils package.
-This package also contains a new version of mtools which allows to
-access high capacity disks (up to 1992K on a high density 3 1/2 disk!).
-It also contains additional documentation about the floppy driver.
-
-The latest version can be found at fdutils homepage:
- http://fdutils.linux.lu
-
-The fdutils releases can be found at:
- http://fdutils.linux.lu/download.html
- http://www.tux.org/pub/knaff/fdutils/
- ftp://metalab.unc.edu/pub/Linux/utils/disk-management/
-
-Reporting problems about the floppy driver
-==========================================
-
- If you have a question or a bug report about the floppy driver, mail
-me at Alain.Knaff@poboxes.com . If you post to Usenet, preferably use
-comp.os.linux.hardware. As the volume in these groups is rather high,
-be sure to include the word "floppy" (or "FLOPPY") in the subject
-line.  If the reported problem happens when mounting floppy disks, be
-sure to mention also the type of the filesystem in the subject line.
-
- Be sure to read the FAQ before mailing/posting any bug reports!
-
- Alain
-
-Changelog
-=========
-
-10-30-2004 :    Cleanup, updating, add reference to module configuration.
-                James Nelson <james4765@gmail.com>
-
-6-3-2000 :      Original Document