Merge tag 'v3.7-rc3' into for-linus to sync up with recent USB changes

8 files changed, 351 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
new file mode 100644
index 000000000000..0a85c70cd30a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
@@ -0,0 +1,68 @@
+* Atmel High Speed MultiMedia Card Interface
+
+This controller on atmel products provides an interface for MMC, SD and SDIO
+types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the atmel-mci driver.
+
+1) MCI node
+
+Required properties:
+- compatible: should be "atmel,hsmci"
+- #address-cells: should be one. The cell is the slot id.
+- #size-cells: should be zero.
+- at least one slot node
+
+The node contains child nodes for each slot that the platform uses
+
+Example MCI node:
+
+mmc0: mmc@f0008000 {
+        compatible = "atmel,hsmci";
+        reg = <0xf0008000 0x600>;
+        interrupts = <12 4>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        [ child node definitions...]
+};
+
+2) slot nodes
+
+Required properties:
+- reg: should contain the slot id.
+- bus-width: number of data lines connected to the controller
+
+Optional properties:
+- cd-gpios: specify GPIOs for card detection
+- cd-inverted: invert the value of external card detect gpio line
+- wp-gpios: specify GPIOs for write protection
+
+Example slot node:
+
+slot@0 {
+        reg = <0>;
+        bus-width = <4>;
+        cd-gpios = <&pioD 15 0>
+        cd-inverted;
+};
+
+Example full MCI node:
+mmc0: mmc@f0008000 {
+        compatible = "atmel,hsmci";
+        reg = <0xf0008000 0x600>;
+        interrupts = <12 4>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        slot@0 {
+                reg = <0>;
+                bus-width = <4>;
+                cd-gpios = <&pioD 15 0>
+                cd-inverted;
+        };
+        slot@1 {
+                reg = <1>;
+                bus-width = <4>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
new file mode 100644
index 000000000000..792768953330
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -0,0 +1,87 @@
+* Samsung Exynos specific extensions to the Synopsis Designware Mobile
+  Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsis dw mshc controller properties described
+by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific
+extensions to the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+        - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
+          specific extentions.
+        - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
+          specific extentions.
+        - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
+          specific extentions.
+
+* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
+  unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
+  ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
+
+* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for single
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for double
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+  Notes for the sdr-timing and ddr-timing values:
+
+    The order of the cells should be
+      - First Cell: CIU clock phase shift value for tx mode.
+      - Second Cell: CIU clock phase shift value for rx mode.
+
+    Valid values for SDR and DDR CIU clock timing for Exynos5250:
+      - valid value for tx phase shift and rx phase shift is 0 to 7.
+      - when CIU clock divider value is set to 3, all possible 8 phase shift
+        values can be used.
+      - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
+        phase shift clocks should be 0.
+
+Required properties for a slot:
+
+* gpios: specifies a list of gpios used for command, clock and data bus. The
+  first gpio is the command line and the second gpio is the clock line. The
+  rest of the gpios (depending on the bus-width property) are the data lines in
+  no particular order. The format of the gpio specifier depends on the gpio
+  controller.
+
+Example:
+
+  The MSHC controller node can be split into two portions, SoC specific and
+  board specific portions as listed below.
+
+        dwmmc0@12200000 {
+                compatible = "samsung,exynos5250-dw-mshc";
+                reg = <0x12200000 0x1000>;
+                interrupts = <0 75 0>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+        };
+
+        dwmmc0@12200000 {
+                num-slots = <1>;
+                supports-highspeed;
+                broken-cd;
+                fifo-depth = <0x80>;
+                card-detect-delay = <200>;
+                samsung,dw-mshc-ciu-div = <3>;
+                samsung,dw-mshc-sdr-timing = <2 3>;
+                samsung,dw-mshc-ddr-timing = <1 2>;
+
+                slot@0 {
+                        reg = <0>;
+                        bus-width = <8>;
+                        gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
+                                <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
+                                <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
+                                <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
+                                <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
+                };
+        };
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 8a6811f4a02f..8e2e0ba2f486 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -9,12 +9,17 @@ Interpreted by the OF core:
 Required properties:
 - bus-width: Number of data lines, can be <1>, <4>, or <8>
 
+Card detection:
+If no property below is supplied, standard SDHCI card detect is used.
+Only one of the properties in this section should be supplied:
+  - broken-cd: There is no card detection available; polling must be used.
+  - cd-gpios: Specify GPIOs for card detection, see gpio binding
+  - non-removable: non-removable slot (like eMMC); assume always present.
+
 Optional properties:
-- cd-gpios: Specify GPIOs for card detection, see gpio binding
 - wp-gpios: Specify GPIOs for write protection, see gpio binding
 - cd-inverted: when present, polarity on the cd gpio line is inverted
 - wp-inverted: when present, polarity on the wp gpio line is inverted
-- non-removable: non-removable slot (like eMMC)
 - max-frequency: maximum operating clock frequency
 
 Example:
diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt
new file mode 100644
index 000000000000..b7025de7dced
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt
@@ -0,0 +1,25 @@
+* PXA MMC drivers
+
+Driver bindings for the PXA MCI (MMC/SDIO) interfaces
+
+Required properties:
+- compatible: Should be "marvell,pxa-mmc".
+- vmmc-supply: A regulator for VMMC
+
+Optional properties:
+- marvell,detect-delay-ms: sets the detection delay timeout in ms.
+- marvell,gpio-power: GPIO spec for the card power enable pin
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the pxa-mmc driver.
+
+Examples:
+
+mmc0: mmc@41100000 {
+        compatible = "marvell,pxa-mmc";
+        reg = <0x41100000 0x1000>;
+        interrupts = <23>;
+        cd-gpios = <&gpio 23 0>;
+        wp-gpios = <&gpio 24 0>;
+};
+
diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
new file mode 100644
index 000000000000..630a7d7f4718
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
@@ -0,0 +1,53 @@
+* Samsung's SDHCI Controller device tree bindings
+
+Samsung's SDHCI controller is used as a connectivity interface with external
+MMC, SD and eMMC storage mediums. This file documents differences between the
+core mmc properties described by mmc.txt and the properties used by the
+Samsung implmentation of the SDHCI controller.
+
+Note: The mmc core bindings documentation states that if none of the core
+card-detect bindings are used, then the standard sdhci card detect mechanism
+is used. The Samsung's SDHCI controller bindings extends this as listed below.
+
+[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
+    "Optional Board Specific Properties" section below.
+
+[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property
+    is not specified, it is assumed that there is no card detection
+    mechanism used.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+  - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
+    controller.
+  - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci
+    controller.
+
+Required Board Specific Properties:
+- gpios: Should specify the gpios used for clock, command and data lines. The
+  gpio specifier format depends on the gpio controller.
+
+Optional Board Specific Properties:
+- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
+  through a pinmux to the card-detect pin of the card slot. This property
+  should be used only if none of the mmc core card-detect properties are
+  used.
+
+Example:
+        sdhci@12530000 {
+                compatible = "samsung,exynos4210-sdhci";
+                reg = <0x12530000 0x100>;
+                interrupts = <0 75 0>;
+                bus-width = <4>;
+                cd-gpios = <&gpk2 2 2 3 3>;
+                gpios = <&gpk2 0 2 0 3>,  /* clock line */
+                        <&gpk2 1 2 0 3>,  /* command line */
+                        <&gpk2 3 2 3 3>,  /* data line 0 */
+                        <&gpk2 4 2 3 3>,  /* data line 1 */
+                        <&gpk2 5 2 3 3>,  /* data line 2 */
+                        <&gpk2 6 2 3 3>;  /* data line 3 */
+        };
+
+        Note: This example shows both SoC specific and board specific properties
+        in a single device node. The properties can be actually be seperated
+        into SoC specific node and board specific node.
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt
new file mode 100644
index 000000000000..ae9aab9abcd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt
@@ -0,0 +1,14 @@
+* Marvell sdhci-dove controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers.
+
+- compatible: Should be "marvell,dove-sdhci".
+
+Example:
+
+sdio0: sdio@92000 {
+        compatible = "marvell,dove-sdhci";
+        reg = <0x92000 0x100>;
+        interrupts = <35>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt
new file mode 100644
index 000000000000..fd3643e7e467
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt
@@ -0,0 +1,18 @@
+* SPEAr SDHCI Controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-spear driver.
+
+Required properties:
+- compatible: "st,spear300-sdhci"
+
+Optional properties:
+- cd-gpios: card detect gpio, with zero flags.
+
+Example:
+
+        sdhci@fc000000 {
+                compatible = "st,spear300-sdhci";
+                reg = <0xfc000000 0x1000>;
+                cd-gpios = <&gpio0 6 0>;
+        };
diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
new file mode 100644
index 000000000000..06cd32d08052
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
@@ -0,0 +1,79 @@
+* Synopsis Designware Mobile Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core mmc properties described by mmc.txt and the
+properties used by the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+        - snps,dw-mshc: for controllers compliant with synopsis dw-mshc.
+* #address-cells: should be 1.
+* #size-cells: should be 0.
+
+# Slots: The slot specific information are contained within child-nodes with
+  each child-node representing a supported slot. There should be atleast one
+  child node representing a card slot. The name of the child node representing
+  the slot is recommended to be slot@n where n is the unique number of the slot
+  connnected to the controller. The following are optional properties which
+  can be included in the slot child node.
+
+        * reg: specifies the physical slot number. The valid values of this
+          property is 0 to (num-slots -1), where num-slots is the value
+          specified by the num-slots property.
+
+        * bus-width: as documented in mmc core bindings.
+
+        * wp-gpios: specifies the write protect gpio line. The format of the
+          gpio specifier depends on the gpio controller. If the write-protect
+          line is not available, this property is optional.
+
+Optional properties:
+
+* num-slots: specifies the number of slots supported by the controller.
+  The number of physical slots actually used could be equal or less than the
+  value specified by num-slots. If this property is not specified, the value
+  of num-slot property is assumed to be 1.
+
+* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not
+  specified, the default value of the fifo size is determined from the
+  controller registers.
+
+* card-detect-delay: Delay in milli-seconds before detecting card after card
+  insert event. The default value is 0.
+
+* supports-highspeed: Enables support for high speed cards (upto 50MHz)
+
+* broken-cd: as documented in mmc core bindings.
+
+Aliases:
+
+- All the MSHC controller nodes should be represented in the aliases node using
+  the following format 'mshc{n}' where n is a unique number for the alias.
+
+Example:
+
+The MSHC controller node can be split into two portions, SoC specific and
+board specific portions as listed below.
+
+        dwmmc0@12200000 {
+                compatible = "snps,dw-mshc";
+                reg = <0x12200000 0x1000>;
+                interrupts = <0 75 0>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+        };
+
+        dwmmc0@12200000 {
+                num-slots = <1>;
+                supports-highspeed;
+                broken-cd;
+                fifo-depth = <0x80>;
+                card-detect-delay = <200>;
+
+                slot@0 {
+                        reg = <0>;
+                        bus-width = <8>;
+                };
+        };