at91: at91sam9g20ek modify dual slot evaluation kit

at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.

Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>

2 files changed, 26 insertions, 17 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index e35d54d43e70..2fd88437348b 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -289,13 +289,6 @@ config MACH_NEOCORE926
         help
           Select this if you are using the Adeneo Neocore 926 board.
 
-config MACH_AT91SAM9G20EK_2MMC
-        bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots"
-        depends on ARCH_AT91SAM9G20
-        help
-          Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
-          Rev A or B modified for 2 MMC Slots.
-
 endif
 
 # ----------------------------------------------------------
@@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK
         bool "Atmel AT91SAM9G20-EK Evaluation Kit"
         depends on ARCH_AT91SAM9G20
         help
-          Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
+          Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit
+          that embeds only one SD/MMC slot.
+
+config MACH_AT91SAM9G20EK_2MMC
+        bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
+        depends on ARCH_AT91SAM9G20
+        help
+          Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
+          with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
+          onwards.
 
 config MACH_CPU9G20
         bool "Eukrea CPU9G20 board"
@@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD
 
 config MTD_NAND_ATMEL_BUSWIDTH_16
         bool "Enable 16-bit data bus interface to NAND flash"
-        depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
+        depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
         help
           On AT91SAM926x boards both types of NAND flash can be present
           (8 and 16 bit data bus width).
diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c
index a28e53faf71d..a4102d72cc9b 100644
--- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c
+++ b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c
@@ -90,7 +90,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_ATMELMCI)
+#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
         {       /* DataFlash chip */
                 .modalias       = "mtd_dataflash",
                 .chip_select    = 1,
@@ -113,7 +113,7 @@ static struct spi_board_info ek_spi_devices[] = {
  * MACB Ethernet device
  */
 static struct at91_eth_data __initdata ek_macb_data = {
-        .phy_irq_pin    = AT91_PIN_PC12,
+        .phy_irq_pin    = AT91_PIN_PB0,
         .is_rmii        = 1,
 };
 
@@ -194,24 +194,27 @@ static void __init ek_add_device_nand(void)
 
 /*
  * MCI (SD/MMC)
- * det_pin and wp_pin are not connected
+ * wp_pin is not connected
  */
 #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 static struct mci_platform_data __initdata ek_mmc_data = {
         .slot[0] = {
                 .bus_width      = 4,
-                .detect_pin     = -ENODEV,
+                .detect_pin     = AT91_PIN_PC2,
                 .wp_pin         = -ENODEV,
         },
         .slot[1] = {
                 .bus_width      = 4,
-                .detect_pin     = -ENODEV,
+                .detect_pin     = AT91_PIN_PC9,
                 .wp_pin         = -ENODEV,
         },
 
 };
 #else
-static struct amci_platform_data __initdata ek_mmc_data = {
+static struct at91_mmc_data __initdata ek_mmc_data = {
+        .slot_b         = 1,    /* Only one slot so use slot B */
+        .wire4          = 1,
+        .det_pin        = AT91_PIN_PC9,
 };
 #endif
 
@@ -221,13 +224,13 @@ static struct amci_platform_data __initdata ek_mmc_data = {
 static struct gpio_led ek_leds[] = {
         {       /* "bottom" led, green, userled1 to be defined */
                 .name                   = "ds5",
-                .gpio                   = AT91_PIN_PB12,
+                .gpio                   = AT91_PIN_PB8,
                 .active_low             = 1,
                 .default_trigger        = "none",
         },
         {       /* "power" led, yellow */
                 .name                   = "ds1",
-                .gpio                   = AT91_PIN_PB13,
+                .gpio                   = AT91_PIN_PB9,
                 .default_trigger        = "heartbeat",
         }
 };
@@ -254,7 +257,11 @@ static void __init ek_board_init(void)
         /* Ethernet */
         at91_add_device_eth(&ek_macb_data);
         /* MMC */
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
         at91_add_device_mci(0, &ek_mmc_data);
+#else
+        at91_add_device_mmc(0, &ek_mmc_data);
+#endif
         /* I2C */
         at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
         /* LEDs */