[ARM] Feroceon: L2 cache support

This patch adds support for the unified Feroceon L2 cache controller
as found in e.g. the Marvell Kirkwood and Marvell Discovery Duo
families of ARM SoCs.

Note that:

- Page table walks are outer uncacheable on Kirkwood and Discovery
  Duo, since the ARMv5 spec provides no way to indicate outer
  cacheability of page table walks (specifying it in TTBR[4:3] is
  an ARMv6+ feature).

  This requires adding L2 cache clean instructions to
  proc-feroceon.S (dcache_clean_area(), set_pte()) as well as to
  tlbflush.h ({flush,clean}_pmd_entry()).  The latter case is handled
  by defining a new TLB type (TLB_FEROCEON) which is almost identical
  to the v4wbi one but provides a TLB_L2CLEAN_FR flag.

- The Feroceon L2 cache controller supports L2 range (i.e. 'clean L2
  range by MVA' and 'invalidate L2 range by MVA') operations, and this
  patch uses those range operations for all Linux outer cache
  operations, as they are faster than the regular per-line operations.

  L2 range operations are not interruptible on this hardware, which
  avoids potential livelock issues, but can be bad for interrupt
  latency, so there is a compile-time tunable (MAX_RANGE_SIZE) which
  allows you to select the maximum range size to operate on at once.
  (Valid range is between one cache line and one 4KiB page, and must
  be a multiple of the line size.)

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

6 files changed, 395 insertions, 1 deletions

diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 08ca264459bd..3b90051c0e05 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -373,7 +373,7 @@ config CPU_FEROCEON
         select CPU_CACHE_VIVT
         select CPU_CP15_MMU
         select CPU_COPY_FEROCEON if MMU
-        select CPU_TLB_V4WBI if MMU
+        select CPU_TLB_FEROCEON if MMU
 
 config CPU_FEROCEON_OLD_ID
         bool "Accept early Feroceon cores with an ARM926 ID"
@@ -551,6 +551,11 @@ config CPU_TLB_V4WBI
           ARM Architecture Version 4 TLB with writeback cache and invalidate
           instruction cache entry.
 
+config CPU_TLB_FEROCEON
+        bool
+        help
+          Feroceon TLB (v4wbi with non-outer-cachable page table walks).
+
 config CPU_TLB_V6
         bool
 
@@ -709,6 +714,14 @@ config OUTER_CACHE
         bool
         default n
 
+config CACHE_FEROCEON_L2
+        bool "Enable the Feroceon L2 cache controller"
+        depends on FOOBAR
+        default y
+        select OUTER_CACHE
+        help
+          This option enables the Feroceon L2 cache controller.
+
 config CACHE_L2X0
         bool "Enable the L2x0 outer cache controller"
         depends on REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || MACH_REALVIEW_PB1176
diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile
index 32b2d2d213a6..f64b92557b11 100644
--- a/arch/arm/mm/Makefile
+++ b/arch/arm/mm/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_CPU_TLB_V3)	+= tlb-v3.o
 obj-$(CONFIG_CPU_TLB_V4WT)      += tlb-v4.o
 obj-$(CONFIG_CPU_TLB_V4WB)      += tlb-v4wb.o
 obj-$(CONFIG_CPU_TLB_V4WBI)     += tlb-v4wbi.o
+obj-$(CONFIG_CPU_TLB_FEROCEON)  += tlb-v4wbi.o  # reuse v4wbi TLB functions
 obj-$(CONFIG_CPU_TLB_V6)        += tlb-v6.o
 obj-$(CONFIG_CPU_TLB_V7)        += tlb-v7.o
 
@@ -73,4 +74,5 @@ obj-$(CONFIG_CPU_FEROCEON)	+= proc-feroceon.o
 obj-$(CONFIG_CPU_V6)            += proc-v6.o
 obj-$(CONFIG_CPU_V7)            += proc-v7.o
 
+obj-$(CONFIG_CACHE_FEROCEON_L2) += cache-feroceon-l2.o
 obj-$(CONFIG_CACHE_L2X0)        += cache-l2x0.o
diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c
new file mode 100644
index 000000000000..20eec4ba173f
--- /dev/null
+++ b/arch/arm/mm/cache-feroceon-l2.c
@@ -0,0 +1,318 @@
+/*
+ * arch/arm/mm/cache-feroceon-l2.c - Feroceon L2 cache controller support
+ *
+ * Copyright (C) 2008 Marvell Semiconductor
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * References:
+ * - Unified Layer 2 Cache for Feroceon CPU Cores,
+ *   Document ID MV-S104858-00, Rev. A, October 23 2007.
+ */
+
+#include <linux/init.h>
+#include <asm/cacheflush.h>
+#include <asm/plat-orion/cache-feroceon-l2.h>
+
+
+/*
+ * Low-level cache maintenance operations.
+ *
+ * As well as the regular 'clean/invalidate/flush L2 cache line by
+ * MVA' instructions, the Feroceon L2 cache controller also features
+ * 'clean/invalidate L2 range by MVA' operations.
+ *
+ * Cache range operations are initiated by writing the start and
+ * end addresses to successive cp15 registers, and process every
+ * cache line whose first byte address lies in the inclusive range
+ * [start:end].
+ *
+ * The cache range operations stall the CPU pipeline until completion.
+ *
+ * The range operations require two successive cp15 writes, in
+ * between which we don't want to be preempted.
+ */
+static inline void l2_clean_pa(unsigned long addr)
+{
+        __asm__("mcr p15, 1, %0, c15, c9, 3" : : "r" (addr));
+}
+
+static inline void l2_clean_mva_range(unsigned long start, unsigned long end)
+{
+        unsigned long flags;
+
+        /*
+         * Make sure 'start' and 'end' reference the same page, as
+         * L2 is PIPT and range operations only do a TLB lookup on
+         * the start address.
+         */
+        BUG_ON((start ^ end) & ~(PAGE_SIZE - 1));
+
+        raw_local_irq_save(flags);
+        __asm__("mcr p15, 1, %0, c15, c9, 4" : : "r" (start));
+        __asm__("mcr p15, 1, %0, c15, c9, 5" : : "r" (end));
+        raw_local_irq_restore(flags);
+}
+
+static inline void l2_clean_pa_range(unsigned long start, unsigned long end)
+{
+        l2_clean_mva_range(__phys_to_virt(start), __phys_to_virt(end));
+}
+
+static inline void l2_clean_inv_pa(unsigned long addr)
+{
+        __asm__("mcr p15, 1, %0, c15, c10, 3" : : "r" (addr));
+}
+
+static inline void l2_inv_pa(unsigned long addr)
+{
+        __asm__("mcr p15, 1, %0, c15, c11, 3" : : "r" (addr));
+}
+
+static inline void l2_inv_mva_range(unsigned long start, unsigned long end)
+{
+        unsigned long flags;
+
+        /*
+         * Make sure 'start' and 'end' reference the same page, as
+         * L2 is PIPT and range operations only do a TLB lookup on
+         * the start address.
+         */
+        BUG_ON((start ^ end) & ~(PAGE_SIZE - 1));
+
+        raw_local_irq_save(flags);
+        __asm__("mcr p15, 1, %0, c15, c11, 4" : : "r" (start));
+        __asm__("mcr p15, 1, %0, c15, c11, 5" : : "r" (end));
+        raw_local_irq_restore(flags);
+}
+
+static inline void l2_inv_pa_range(unsigned long start, unsigned long end)
+{
+        l2_inv_mva_range(__phys_to_virt(start), __phys_to_virt(end));
+}
+
+
+/*
+ * Linux primitives.
+ *
+ * Note that the end addresses passed to Linux primitives are
+ * noninclusive, while the hardware cache range operations use
+ * inclusive start and end addresses.
+ */
+#define CACHE_LINE_SIZE         32
+#define MAX_RANGE_SIZE          1024
+
+static int l2_wt_override;
+
+static unsigned long calc_range_end(unsigned long start, unsigned long end)
+{
+        unsigned long range_end;
+
+        BUG_ON(start & (CACHE_LINE_SIZE - 1));
+        BUG_ON(end & (CACHE_LINE_SIZE - 1));
+
+        /*
+         * Try to process all cache lines between 'start' and 'end'.
+         */
+        range_end = end;
+
+        /*
+         * Limit the number of cache lines processed at once,
+         * since cache range operations stall the CPU pipeline
+         * until completion.
+         */
+        if (range_end > start + MAX_RANGE_SIZE)
+                range_end = start + MAX_RANGE_SIZE;
+
+        /*
+         * Cache range operations can't straddle a page boundary.
+         */
+        if (range_end > (start | (PAGE_SIZE - 1)) + 1)
+                range_end = (start | (PAGE_SIZE - 1)) + 1;
+
+        return range_end;
+}
+
+static void feroceon_l2_inv_range(unsigned long start, unsigned long end)
+{
+        /*
+         * Clean and invalidate partial first cache line.
+         */
+        if (start & (CACHE_LINE_SIZE - 1)) {
+                l2_clean_inv_pa(start & ~(CACHE_LINE_SIZE - 1));
+                start = (start | (CACHE_LINE_SIZE - 1)) + 1;
+        }
+
+        /*
+         * Clean and invalidate partial last cache line.
+         */
+        if (end & (CACHE_LINE_SIZE - 1)) {
+                l2_clean_inv_pa(end & ~(CACHE_LINE_SIZE - 1));
+                end &= ~(CACHE_LINE_SIZE - 1);
+        }
+
+        /*
+         * Invalidate all full cache lines between 'start' and 'end'.
+         */
+        while (start != end) {
+                unsigned long range_end = calc_range_end(start, end);
+                l2_inv_pa_range(start, range_end - CACHE_LINE_SIZE);
+                start = range_end;
+        }
+
+        dsb();
+}
+
+static void feroceon_l2_clean_range(unsigned long start, unsigned long end)
+{
+        /*
+         * If L2 is forced to WT, the L2 will always be clean and we
+         * don't need to do anything here.
+         */
+        if (!l2_wt_override) {
+                start &= ~(CACHE_LINE_SIZE - 1);
+                end = (end + CACHE_LINE_SIZE - 1) & ~(CACHE_LINE_SIZE - 1);
+                while (start != end) {
+                        unsigned long range_end = calc_range_end(start, end);
+                        l2_clean_pa_range(start, range_end - CACHE_LINE_SIZE);
+                        start = range_end;
+                }
+        }
+
+        dsb();
+}
+
+static void feroceon_l2_flush_range(unsigned long start, unsigned long end)
+{
+        start &= ~(CACHE_LINE_SIZE - 1);
+        end = (end + CACHE_LINE_SIZE - 1) & ~(CACHE_LINE_SIZE - 1);
+        while (start != end) {
+                unsigned long range_end = calc_range_end(start, end);
+                if (!l2_wt_override)
+                        l2_clean_pa_range(start, range_end - CACHE_LINE_SIZE);
+                l2_inv_pa_range(start, range_end - CACHE_LINE_SIZE);
+                start = range_end;
+        }
+
+        dsb();
+}
+
+
+/*
+ * Routines to disable and re-enable the D-cache and I-cache at run
+ * time.  These are necessary because the L2 cache can only be enabled
+ * or disabled while the L1 Dcache and Icache are both disabled.
+ */
+static void __init invalidate_and_disable_dcache(void)
+{
+        u32 cr;
+
+        cr = get_cr();
+        if (cr & CR_C) {
+                unsigned long flags;
+
+                raw_local_irq_save(flags);
+                flush_cache_all();
+                set_cr(cr & ~CR_C);
+                raw_local_irq_restore(flags);
+        }
+}
+
+static void __init enable_dcache(void)
+{
+        u32 cr;
+
+        cr = get_cr();
+        if (!(cr & CR_C))
+                set_cr(cr | CR_C);
+}
+
+static void __init __invalidate_icache(void)
+{
+        int dummy;
+
+        __asm__ __volatile__("mcr p15, 0, %0, c7, c5, 0\n" : "=r" (dummy));
+}
+
+static void __init invalidate_and_disable_icache(void)
+{
+        u32 cr;
+
+        cr = get_cr();
+        if (cr & CR_I) {
+                set_cr(cr & ~CR_I);
+                __invalidate_icache();
+        }
+}
+
+static void __init enable_icache(void)
+{
+        u32 cr;
+
+        cr = get_cr();
+        if (!(cr & CR_I))
+                set_cr(cr | CR_I);
+}
+
+static inline u32 read_extra_features(void)
+{
+        u32 u;
+
+        __asm__("mrc p15, 1, %0, c15, c1, 0" : "=r" (u));
+
+        return u;
+}
+
+static inline void write_extra_features(u32 u)
+{
+        __asm__("mcr p15, 1, %0, c15, c1, 0" : : "r" (u));
+}
+
+static void __init disable_l2_prefetch(void)
+{
+        u32 u;
+
+        /*
+         * Read the CPU Extra Features register and verify that the
+         * Disable L2 Prefetch bit is set.
+         */
+        u = read_extra_features();
+        if (!(u & 0x01000000)) {
+                printk(KERN_INFO "Feroceon L2: Disabling L2 prefetch.\n");
+                write_extra_features(u | 0x01000000);
+        }
+}
+
+static void __init enable_l2(void)
+{
+        u32 u;
+
+        u = read_extra_features();
+        if (!(u & 0x00400000)) {
+                printk(KERN_INFO "Feroceon L2: Enabling L2\n");
+
+                invalidate_and_disable_dcache();
+                invalidate_and_disable_icache();
+                write_extra_features(u | 0x00400000);
+                enable_icache();
+                enable_dcache();
+        }
+}
+
+void __init feroceon_l2_init(int __l2_wt_override)
+{
+        l2_wt_override = __l2_wt_override;
+
+        disable_l2_prefetch();
+
+        outer_cache.inv_range = feroceon_l2_inv_range;
+        outer_cache.clean_range = feroceon_l2_clean_range;
+        outer_cache.flush_range = feroceon_l2_flush_range;
+
+        enable_l2();
+
+        printk(KERN_INFO "Feroceon L2: Cache support initialised%s.\n",
+                         l2_wt_override ? ", in WT override mode" : "");
+}
diff --git a/arch/arm/mm/proc-feroceon.S b/arch/arm/mm/proc-feroceon.S
index c279652a98fd..cecf96ee07d5 100644
--- a/arch/arm/mm/proc-feroceon.S
+++ b/arch/arm/mm/proc-feroceon.S
@@ -79,6 +79,13 @@ ENTRY(cpu_feroceon_proc_fin)
         mov     ip, #PSR_F_BIT | PSR_I_BIT | SVC_MODE
         msr     cpsr_c, ip
         bl      feroceon_flush_kern_cache_all
+
+#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH)
+        mov     r0, #0
+        mcr     p15, 1, r0, c15, c9, 0          @ clean L2
+        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
+#endif
+
         mrc     p15, 0, r0, c1, c0, 0           @ ctrl register
         bic     r0, r0, #0x1000                 @ ...i............
         bic     r0, r0, #0x000e                 @ ............wca.
@@ -382,10 +389,20 @@ ENTRY(feroceon_range_cache_fns)
 
         .align  5
 ENTRY(cpu_feroceon_dcache_clean_area)
+#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH)
+        mov     r2, r0
+        mov     r3, r1
+#endif
 1:      mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
         add     r0, r0, #CACHE_DLINESIZE
         subs    r1, r1, #CACHE_DLINESIZE
         bhi     1b
+#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH)
+1:      mcr     p15, 1, r2, c15, c9, 1          @ clean L2 entry
+        add     r2, r2, #CACHE_DLINESIZE
+        subs    r3, r3, #CACHE_DLINESIZE
+        bhi     1b
+#endif
         mcr     p15, 0, r0, c7, c10, 4          @ drain WB
         mov     pc, lr
 
@@ -449,6 +466,9 @@ ENTRY(cpu_feroceon_set_pte_ext)
         str     r2, [r0]                        @ hardware version
         mov     r0, r0
         mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
+#if defined(CONFIG_CACHE_FEROCEON_L2) && !defined(CONFIG_L2_CACHE_WRITETHROUGH)
+        mcr     p15, 1, r0, c15, c9, 1          @ clean L2 entry
+#endif
         mcr     p15, 0, r0, c7, c10, 4          @ drain WB
 #endif
         mov     pc, lr
diff --git a/include/asm-arm/plat-orion/cache-feroceon-l2.h b/include/asm-arm/plat-orion/cache-feroceon-l2.h
new file mode 100644
index 000000000000..ba4e016d3ec0
--- /dev/null
+++ b/include/asm-arm/plat-orion/cache-feroceon-l2.h
@@ -0,0 +1,11 @@
+/*
+ * include/asm-arm/plat-orion/cache-feroceon-l2.h
+ *
+ * Copyright (C) 2008 Marvell Semiconductor
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+extern void __init feroceon_l2_init(int l2_wt_override);
diff --git a/include/asm-arm/tlbflush.h b/include/asm-arm/tlbflush.h
index 8c6bc1bb9d1a..909656c747ef 100644
--- a/include/asm-arm/tlbflush.h
+++ b/include/asm-arm/tlbflush.h
@@ -39,6 +39,7 @@
 #define TLB_V6_D_ASID   (1 << 17)
 #define TLB_V6_I_ASID   (1 << 18)
 
+#define TLB_L2CLEAN_FR  (1 << 29)               /* Feroceon */
 #define TLB_DCLEAN      (1 << 30)
 #define TLB_WB          (1 << 31)
 
@@ -51,6 +52,7 @@
  *        v4    - ARMv4 without write buffer
  *        v4wb  - ARMv4 with write buffer without I TLB flush entry instruction
  *        v4wbi - ARMv4 with write buffer with I TLB flush entry instruction
+ *        fr    - Feroceon (v4wbi with non-outer-cacheable page table walks)
  *        v6wbi - ARMv6 with write buffer with I TLB flush entry instruction
  */
 #undef _TLB
@@ -103,6 +105,23 @@
 # define v4wbi_always_flags     (-1UL)
 #endif
 
+#define fr_tlb_flags    (TLB_WB | TLB_DCLEAN | TLB_L2CLEAN_FR | \
+                         TLB_V4_I_FULL | TLB_V4_D_FULL | \
+                         TLB_V4_I_PAGE | TLB_V4_D_PAGE)
+
+#ifdef CONFIG_CPU_TLB_FEROCEON
+# define fr_possible_flags      fr_tlb_flags
+# define fr_always_flags        fr_tlb_flags
+# ifdef _TLB
+#  define MULTI_TLB 1
+# else
+#  define _TLB v4wbi
+# endif
+#else
+# define fr_possible_flags      0
+# define fr_always_flags        (-1UL)
+#endif
+
 #define v4wb_tlb_flags  (TLB_WB | TLB_DCLEAN | \
                          TLB_V4_I_FULL | TLB_V4_D_FULL | \
                          TLB_V4_D_PAGE)
@@ -245,12 +264,14 @@ extern struct cpu_tlb_fns cpu_tlb;
 #define possible_tlb_flags      (v3_possible_flags | \
                                  v4_possible_flags | \
                                  v4wbi_possible_flags | \
+                                 fr_possible_flags | \
                                  v4wb_possible_flags | \
                                  v6wbi_possible_flags)
 
 #define always_tlb_flags        (v3_always_flags & \
                                  v4_always_flags & \
                                  v4wbi_always_flags & \
+                                 fr_always_flags & \
                                  v4wb_always_flags & \
                                  v6wbi_always_flags)
 
@@ -417,6 +438,11 @@ static inline void flush_pmd_entry(pmd_t *pmd)
         if (tlb_flag(TLB_DCLEAN))
                 asm("mcr        p15, 0, %0, c7, c10, 1  @ flush_pmd"
                         : : "r" (pmd) : "cc");
+
+        if (tlb_flag(TLB_L2CLEAN_FR))
+                asm("mcr        p15, 1, %0, c15, c9, 1  @ L2 flush_pmd"
+                        : : "r" (pmd) : "cc");
+
         if (tlb_flag(TLB_WB))
                 dsb();
 }
@@ -428,6 +454,10 @@ static inline void clean_pmd_entry(pmd_t *pmd)
         if (tlb_flag(TLB_DCLEAN))
                 asm("mcr        p15, 0, %0, c7, c10, 1  @ flush_pmd"
                         : : "r" (pmd) : "cc");
+
+        if (tlb_flag(TLB_L2CLEAN_FR))
+                asm("mcr        p15, 1, %0, c15, c9, 1  @ L2 flush_pmd"
+                        : : "r" (pmd) : "cc");
 }
 
 #undef tlb_flag