Merge of 'docs' branch from

	rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

5 files changed, 610 insertions, 92 deletions

diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl
index cf2fce7707da..6df1dfd18b65 100644
--- a/Documentation/DocBook/libata.tmpl
+++ b/Documentation/DocBook/libata.tmpl
@@ -14,7 +14,7 @@
   </authorgroup>
 
   <copyright>
-   <year>2003</year>
+   <year>2003-2005</year>
    <holder>Jeff Garzik</holder>
   </copyright>
 
@@ -44,30 +44,38 @@
 
 <toc></toc>
 
-  <chapter id="libataThanks">
-     <title>Thanks</title>
+  <chapter id="libataIntroduction">
+     <title>Introduction</title>
   <para>
-  The bulk of the ATA knowledge comes thanks to long conversations with
-  Andre Hedrick (www.linux-ide.org).
+  libATA is a library used inside the Linux kernel to support ATA host
+  controllers and devices.  libATA provides an ATA driver API, class
+  transports for ATA and ATAPI devices, and SCSI&lt;-&gt;ATA translation
+  for ATA devices according to the T10 SAT specification.
   </para>
   <para>
-  Thanks to Alan Cox for pointing out similarities 
-  between SATA and SCSI, and in general for motivation to hack on
-  libata.
-  </para>
-  <para>
-  libata's device detection
-  method, ata_pio_devchk, and in general all the early probing was
-  based on extensive study of Hale Landis's probe/reset code in his
-  ATADRVR driver (www.ata-atapi.com).
+  This Guide documents the libATA driver API, library functions, library
+  internals, and a couple sample ATA low-level drivers.
   </para>
   </chapter>
 
   <chapter id="libataDriverApi">
      <title>libata Driver API</title>
+     <para>
+     struct ata_port_operations is defined for every low-level libata
+     hardware driver, and it controls how the low-level driver
+     interfaces with the ATA and SCSI layers.
+     </para>
+     <para>
+     FIS-based drivers will hook into the system with ->qc_prep() and
+     ->qc_issue() high-level hooks.  Hardware which behaves in a manner
+     similar to PCI IDE hardware may utilize several generic helpers,
+     defining at a bare minimum the bus I/O addresses of the ATA shadow
+     register blocks.
+     </para>
      <sect1>
         <title>struct ata_port_operations</title>
 
+        <sect2><title>Disable ATA port</title>
         <programlisting>
 void (*port_disable) (struct ata_port *);
         </programlisting>
@@ -78,6 +86,9 @@ void (*port_disable) (struct ata_port *);
         unplug).
         </para>
 
+        </sect2>
+
+        <sect2><title>Post-IDENTIFY device configuration</title>
         <programlisting>
 void (*dev_config) (struct ata_port *, struct ata_device *);
         </programlisting>
@@ -88,6 +99,9 @@ void (*dev_config) (struct ata_port *, struct ata_device *);
         issue of SET FEATURES - XFER MODE, and prior to operation.
         </para>
 
+        </sect2>
+
+        <sect2><title>Set PIO/DMA mode</title>
         <programlisting>
 void (*set_piomode) (struct ata_port *, struct ata_device *);
 void (*set_dmamode) (struct ata_port *, struct ata_device *);
@@ -108,6 +122,9 @@ void (*post_set_mode) (struct ata_port *ap);
         ->set_dma_mode() is only called if DMA is possible.
         </para>
 
+        </sect2>
+
+        <sect2><title>Taskfile read/write</title>
         <programlisting>
 void (*tf_load) (struct ata_port *ap, struct ata_taskfile *tf);
 void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
@@ -120,6 +137,9 @@ void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
         taskfile register values.
         </para>
 
+        </sect2>
+
+        <sect2><title>ATA command execute</title>
         <programlisting>
 void (*exec_command)(struct ata_port *ap, struct ata_taskfile *tf);
         </programlisting>
@@ -129,17 +149,37 @@ void (*exec_command)(struct ata_port *ap, struct ata_taskfile *tf);
         ->tf_load(), to be initiated in hardware.
         </para>
 
+        </sect2>
+
+        <sect2><title>Per-cmd ATAPI DMA capabilities filter</title>
+        <programlisting>
+int (*check_atapi_dma) (struct ata_queued_cmd *qc);
+        </programlisting>
+
+        <para>
+Allow low-level driver to filter ATA PACKET commands, returning a status
+indicating whether or not it is OK to use DMA for the supplied PACKET
+command.
+        </para>
+
+        </sect2>
+
+        <sect2><title>Read specific ATA shadow registers</title>
         <programlisting>
 u8   (*check_status)(struct ata_port *ap);
-void (*dev_select)(struct ata_port *ap, unsigned int device);
+u8   (*check_altstatus)(struct ata_port *ap);
+u8   (*check_err)(struct ata_port *ap);
         </programlisting>
 
         <para>
-        Reads the Status ATA shadow register from hardware.  On some
-        hardware, this has the side effect of clearing the interrupt
-        condition.
+        Reads the Status/AltStatus/Error ATA shadow register from
+        hardware.  On some hardware, reading the Status register has
+        the side effect of clearing the interrupt condition.
         </para>
 
+        </sect2>
+
+        <sect2><title>Select ATA device on bus</title>
         <programlisting>
 void (*dev_select)(struct ata_port *ap, unsigned int device);
         </programlisting>
@@ -147,9 +187,13 @@ void (*dev_select)(struct ata_port *ap, unsigned int device);
         <para>
         Issues the low-level hardware command(s) that causes one of N
         hardware devices to be considered 'selected' (active and
-        available for use) on the ATA bus.
+        available for use) on the ATA bus.  This generally has no
+meaning on FIS-based devices.
         </para>
 
+        </sect2>
+
+        <sect2><title>Reset ATA bus</title>
         <programlisting>
 void (*phy_reset) (struct ata_port *ap);
         </programlisting>
@@ -162,17 +206,31 @@ void (*phy_reset) (struct ata_port *ap);
         functions ata_bus_reset() or sata_phy_reset() for this hook.
         </para>
 
+        </sect2>
+
+        <sect2><title>Control PCI IDE BMDMA engine</title>
         <programlisting>
 void (*bmdma_setup) (struct ata_queued_cmd *qc);
 void (*bmdma_start) (struct ata_queued_cmd *qc);
+void (*bmdma_stop) (struct ata_port *ap);
+u8   (*bmdma_status) (struct ata_port *ap);
         </programlisting>
 
         <para>
-        When setting up an IDE BMDMA transaction, these hooks arm
-        (->bmdma_setup) and fire (->bmdma_start) the hardware's DMA
-        engine.
+When setting up an IDE BMDMA transaction, these hooks arm
+(->bmdma_setup), fire (->bmdma_start), and halt (->bmdma_stop)
+the hardware's DMA engine.  ->bmdma_status is used to read the standard
+PCI IDE DMA Status register.
         </para>
 
+        <para>
+These hooks are typically either no-ops, or simply not implemented, in
+FIS-based drivers.
+        </para>
+
+        </sect2>
+
+        <sect2><title>High-level taskfile hooks</title>
         <programlisting>
 void (*qc_prep) (struct ata_queued_cmd *qc);
 int (*qc_issue) (struct ata_queued_cmd *qc);
@@ -190,20 +248,26 @@ int (*qc_issue) (struct ata_queued_cmd *qc);
         ->qc_issue is used to make a command active, once the hardware
         and S/G tables have been prepared.  IDE BMDMA drivers use the
         helper function ata_qc_issue_prot() for taskfile protocol-based
-        dispatch.  More advanced drivers roll their own ->qc_issue
-        implementation, using this as the "issue new ATA command to
-        hardware" hook.
+        dispatch.  More advanced drivers implement their own ->qc_issue.
         </para>
 
+        </sect2>
+
+        <sect2><title>Timeout (error) handling</title>
         <programlisting>
 void (*eng_timeout) (struct ata_port *ap);
         </programlisting>
 
         <para>
-        This is a high level error handling function, called from the
-        error handling thread, when a command times out.
+This is a high level error handling function, called from the
+error handling thread, when a command times out.  Most newer
+hardware will implement its own error handling code here.  IDE BMDMA
+drivers may use the helper function ata_eng_timeout().
         </para>
 
+        </sect2>
+
+        <sect2><title>Hardware interrupt handling</title>
         <programlisting>
 irqreturn_t (*irq_handler)(int, void *, struct pt_regs *);
 void (*irq_clear) (struct ata_port *);
@@ -216,6 +280,9 @@ void (*irq_clear) (struct ata_port *);
         is quiet.
         </para>
 
+        </sect2>
+
+        <sect2><title>SATA phy read/write</title>
         <programlisting>
 u32 (*scr_read) (struct ata_port *ap, unsigned int sc_reg);
 void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
@@ -227,6 +294,9 @@ void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
         if ->phy_reset hook called the sata_phy_reset() helper function.
         </para>
 
+        </sect2>
+
+        <sect2><title>Init and shutdown</title>
         <programlisting>
 int (*port_start) (struct ata_port *ap);
 void (*port_stop) (struct ata_port *ap);
@@ -240,15 +310,17 @@ void (*host_stop) (struct ata_host_set *host_set);
         tasks.  
         </para>
         <para>
-        ->host_stop() is called when the rmmod or hot unplug process
-        begins.  The hook must stop all hardware interrupts, DMA
-        engines, etc.
-        </para>
-        <para>
         ->port_stop() is called after ->host_stop().  It's sole function
         is to release DMA/memory resources, now that they are no longer
         actively being used.
         </para>
+        <para>
+        ->host_stop() is called after all ->port_stop() calls
+have completed.  The hook must finalize hardware shutdown, release DMA
+and other resources, etc.
+        </para>
+
+        </sect2>
 
      </sect1>
   </chapter>
@@ -279,4 +351,24 @@ void (*host_stop) (struct ata_host_set *host_set);
 !Idrivers/scsi/sata_sil.c
   </chapter>
 
+  <chapter id="libataThanks">
+     <title>Thanks</title>
+  <para>
+  The bulk of the ATA knowledge comes thanks to long conversations with
+  Andre Hedrick (www.linux-ide.org), and long hours pondering the ATA
+  and SCSI specifications.
+  </para>
+  <para>
+  Thanks to Alan Cox for pointing out similarities 
+  between SATA and SCSI, and in general for motivation to hack on
+  libata.
+  </para>
+  <para>
+  libata's device detection
+  method, ata_pio_devchk, and in general all the early probing was
+  based on extensive study of Hale Landis's probe/reset code in his
+  ATADRVR driver (www.ata-atapi.com).
+  </para>
+  </chapter>
+
 </book>
diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
index 54c52349adc5..3be546439252 100644
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/scsi/ata_piix.c
@@ -665,15 +665,6 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         return ata_pci_init_one(pdev, port_info, n_ports);
 }
 
-/**
- *      piix_init -
- *
- *      LOCKING:
- *
- *      RETURNS:
- *
- */
-
 static int __init piix_init(void)
 {
         int rc;
@@ -689,13 +680,6 @@ static int __init piix_init(void)
         return 0;
 }
 
-/**
- *      piix_exit -
- *
- *      LOCKING:
- *
- */
-
 static void __exit piix_exit(void)
 {
         pci_unregister_driver(&piix_pci_driver);
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 30a88f0e7bd6..21d194c6ace3 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -186,6 +186,28 @@ static void ata_tf_load_mmio(struct ata_port *ap, struct ata_taskfile *tf)
         ata_wait_idle(ap);
 }
 
+
+/**
+ *      ata_tf_load - send taskfile registers to host controller
+ *      @ap: Port to which output is sent
+ *      @tf: ATA taskfile register set
+ *
+ *      Outputs ATA taskfile to standard ATA host controller using MMIO
+ *      or PIO as indicated by the ATA_FLAG_MMIO flag.
+ *      Writes the control, feature, nsect, lbal, lbam, and lbah registers.
+ *      Optionally (ATA_TFLAG_LBA48) writes hob_feature, hob_nsect,
+ *      hob_lbal, hob_lbam, and hob_lbah.
+ *
+ *      This function waits for idle (!BUSY and !DRQ) after writing
+ *      registers.  If the control register has a new value, this
+ *      function also waits for idle after writing control and before
+ *      writing the remaining registers.
+ *
+ *      May be used as the tf_load() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
 void ata_tf_load(struct ata_port *ap, struct ata_taskfile *tf)
 {
         if (ap->flags & ATA_FLAG_MMIO)
@@ -195,11 +217,11 @@ void ata_tf_load(struct ata_port *ap, struct ata_taskfile *tf)
 }
 
 /**
- *      ata_exec_command - issue ATA command to host controller
+ *      ata_exec_command_pio - issue ATA command to host controller
  *      @ap: port to which command is being issued
  *      @tf: ATA taskfile register set
  *
- *      Issues PIO/MMIO write to ATA command register, with proper
+ *      Issues PIO write to ATA command register, with proper
  *      synchronization with interrupt handler / other threads.
  *
  *      LOCKING:
@@ -235,6 +257,18 @@ static void ata_exec_command_mmio(struct ata_port *ap, struct ata_taskfile *tf)
         ata_pause(ap);
 }
 
+
+/**
+ *      ata_exec_command - issue ATA command to host controller
+ *      @ap: port to which command is being issued
+ *      @tf: ATA taskfile register set
+ *
+ *      Issues PIO/MMIO write to ATA command register, with proper
+ *      synchronization with interrupt handler / other threads.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
 void ata_exec_command(struct ata_port *ap, struct ata_taskfile *tf)
 {
         if (ap->flags & ATA_FLAG_MMIO)
@@ -305,7 +339,7 @@ void ata_tf_to_host_nolock(struct ata_port *ap, struct ata_taskfile *tf)
 }
 
 /**
- *      ata_tf_read - input device's ATA taskfile shadow registers
+ *      ata_tf_read_pio - input device's ATA taskfile shadow registers
  *      @ap: Port from which input is read
  *      @tf: ATA taskfile register set for storing input
  *
@@ -368,6 +402,23 @@ static void ata_tf_read_mmio(struct ata_port *ap, struct ata_taskfile *tf)
         }
 }
 
+
+/**
+ *      ata_tf_read - input device's ATA taskfile shadow registers
+ *      @ap: Port from which input is read
+ *      @tf: ATA taskfile register set for storing input
+ *
+ *      Reads ATA taskfile registers for currently-selected device
+ *      into @tf.
+ *
+ *      Reads nsect, lbal, lbam, lbah, and device.  If ATA_TFLAG_LBA48
+ *      is set, also reads the hob registers.
+ *
+ *      May be used as the tf_read() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
 void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
 {
         if (ap->flags & ATA_FLAG_MMIO)
@@ -381,7 +432,7 @@ void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
  *      @ap: port where the device is
  *
  *      Reads ATA taskfile status register for currently-selected device
- *      and return it's value. This also clears pending interrupts
+ *      and return its value. This also clears pending interrupts
  *      from this device
  *
  *      LOCKING:
@@ -397,7 +448,7 @@ static u8 ata_check_status_pio(struct ata_port *ap)
  *      @ap: port where the device is
  *
  *      Reads ATA taskfile status register for currently-selected device
- *      via MMIO and return it's value. This also clears pending interrupts
+ *      via MMIO and return its value. This also clears pending interrupts
  *      from this device
  *
  *      LOCKING:
@@ -408,6 +459,20 @@ static u8 ata_check_status_mmio(struct ata_port *ap)
         return readb((void __iomem *) ap->ioaddr.status_addr);
 }
 
+
+/**
+ *      ata_check_status - Read device status reg & clear interrupt
+ *      @ap: port where the device is
+ *
+ *      Reads ATA taskfile status register for currently-selected device
+ *      and return its value. This also clears pending interrupts
+ *      from this device
+ *
+ *      May be used as the check_status() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
 u8 ata_check_status(struct ata_port *ap)
 {
         if (ap->flags & ATA_FLAG_MMIO)
@@ -415,6 +480,20 @@ u8 ata_check_status(struct ata_port *ap)
         return ata_check_status_pio(ap);
 }
 
+
+/**
+ *      ata_altstatus - Read device alternate status reg
+ *      @ap: port where the device is
+ *
+ *      Reads ATA taskfile alternate status register for
+ *      currently-selected device and return its value.
+ *
+ *      Note: may NOT be used as the check_altstatus() entry in
+ *      ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
 u8 ata_altstatus(struct ata_port *ap)
 {
         if (ap->ops->check_altstatus)
@@ -425,6 +504,20 @@ u8 ata_altstatus(struct ata_port *ap)
         return inb(ap->ioaddr.altstatus_addr);
 }
 
+
+/**
+ *      ata_chk_err - Read device error reg
+ *      @ap: port where the device is
+ *
+ *      Reads ATA taskfile error register for
+ *      currently-selected device and return its value.
+ *
+ *      Note: may NOT be used as the check_err() entry in
+ *      ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
 u8 ata_chk_err(struct ata_port *ap)
 {
         if (ap->ops->check_err)
@@ -873,10 +966,24 @@ void ata_dev_id_string(u16 *id, unsigned char *s,
         }
 }
 
+
+/**
+ *      ata_noop_dev_select - Select device 0/1 on ATA bus
+ *      @ap: ATA channel to manipulate
+ *      @device: ATA device (numbered from zero) to select
+ *
+ *      This function performs no actual function.
+ *
+ *      May be used as the dev_select() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      caller.
+ */
 void ata_noop_dev_select (struct ata_port *ap, unsigned int device)
 {
 }
 
+
 /**
  *      ata_std_dev_select - Select device 0/1 on ATA bus
  *      @ap: ATA channel to manipulate
@@ -884,7 +991,9 @@ void ata_noop_dev_select (struct ata_port *ap, unsigned int device)
  *
  *      Use the method defined in the ATA specification to
  *      make either device 0, or device 1, active on the
- *      ATA channel.
+ *      ATA channel.  Works with both PIO and MMIO.
+ *
+ *      May be used as the dev_select() entry in ata_port_operations.
  *
  *      LOCKING:
  *      caller.
@@ -1190,7 +1299,12 @@ err_out:
  *      ata_bus_probe - Reset and probe ATA bus
  *      @ap: Bus to probe
  *
+ *      Master ATA bus probing function.  Initiates a hardware-dependent
+ *      bus reset, then attempts to identify any devices found on
+ *      the bus.
+ *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  *      RETURNS:
  *      Zero on success, non-zero on error.
@@ -1229,10 +1343,14 @@ err_out:
 }
 
 /**
- *      ata_port_probe -
- *      @ap:
+ *      ata_port_probe - Mark port as enabled
+ *      @ap: Port for which we indicate enablement
  *
- *      LOCKING:
+ *      Modify @ap data structure such that the system
+ *      thinks that the entire port is enabled.
+ *
+ *      LOCKING: host_set lock, or some other form of
+ *      serialization.
  */
 
 void ata_port_probe(struct ata_port *ap)
@@ -1241,10 +1359,15 @@ void ata_port_probe(struct ata_port *ap)
 }
 
 /**
- *      __sata_phy_reset -
- *      @ap:
+ *      __sata_phy_reset - Wake/reset a low-level SATA PHY
+ *      @ap: SATA port associated with target SATA PHY.
+ *
+ *      This function issues commands to standard SATA Sxxx
+ *      PHY registers, to wake up the phy (and device), and
+ *      clear any reset condition.
  *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  */
 void __sata_phy_reset(struct ata_port *ap)
@@ -1289,10 +1412,14 @@ void __sata_phy_reset(struct ata_port *ap)
 }
 
 /**
- *      __sata_phy_reset -
- *      @ap:
+ *      sata_phy_reset - Reset SATA bus.
+ *      @ap: SATA port associated with target SATA PHY.
+ *
+ *      This function resets the SATA bus, and then probes
+ *      the bus for devices.
  *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  */
 void sata_phy_reset(struct ata_port *ap)
@@ -1304,10 +1431,16 @@ void sata_phy_reset(struct ata_port *ap)
 }
 
 /**
- *      ata_port_disable -
- *      @ap:
+ *      ata_port_disable - Disable port.
+ *      @ap: Port to be disabled.
  *
- *      LOCKING:
+ *      Modify @ap data structure such that the system
+ *      thinks that the entire port is disabled, and should
+ *      never attempt to probe or communicate with devices
+ *      on this port.
+ *
+ *      LOCKING: host_set lock, or some other form of
+ *      serialization.
  */
 
 void ata_port_disable(struct ata_port *ap)
@@ -1416,7 +1549,10 @@ static void ata_host_set_dma(struct ata_port *ap, u8 xfer_mode,
  *      ata_set_mode - Program timings and issue SET FEATURES - XFER
  *      @ap: port on which timings will be programmed
  *
+ *      Set ATA device disk transfer mode (PIO3, UDMA6, etc.).
+ *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  */
 static void ata_set_mode(struct ata_port *ap)
@@ -1467,7 +1603,10 @@ err_out:
  *      @tmout_pat: impatience timeout
  *      @tmout: overall timeout
  *
- *      LOCKING:
+ *      Sleep until ATA Status register bit BSY clears,
+ *      or a timeout occurs.
+ *
+ *      LOCKING: None.
  *
  */
 
@@ -1553,10 +1692,14 @@ static void ata_bus_post_reset(struct ata_port *ap, unsigned int devmask)
 }
 
 /**
- *      ata_bus_edd -
- *      @ap:
+ *      ata_bus_edd - Issue EXECUTE DEVICE DIAGNOSTIC command.
+ *      @ap: Port to reset and probe
+ *
+ *      Use the EXECUTE DEVICE DIAGNOSTIC command to reset and
+ *      probe the bus.  Not often used these days.
  *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  */
 
@@ -1633,8 +1776,8 @@ static unsigned int ata_bus_softreset(struct ata_port *ap,
  *      the device is ATA or ATAPI.
  *
  *      LOCKING:
- *      Inherited from caller.  Some functions called by this function
- *      obtain the host_set lock.
+ *      PCI/etc. bus probe sem.
+ *      Obtains host_set lock.
  *
  *      SIDE EFFECTS:
  *      Sets ATA_FLAG_PORT_DISABLED if bus reset fails.
@@ -1876,7 +2019,11 @@ static int fgb(u32 bitmap)
  *      @xfer_mode_out: (output) SET FEATURES - XFER MODE code
  *      @xfer_shift_out: (output) bit shift that selects this mode
  *
+ *      Based on host and device capabilities, determine the
+ *      maximum transfer mode that is amenable to all.
+ *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  *      RETURNS:
  *      Zero on success, negative on error.
@@ -1909,7 +2056,11 @@ static int ata_choose_xfer_mode(struct ata_port *ap,
  *      @ap: Port associated with device @dev
  *      @dev: Device to which command will be sent
  *
+ *      Issue SET FEATURES - XFER MODE command to device @dev
+ *      on port @ap.
+ *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  */
 
 static void ata_dev_set_xfermode(struct ata_port *ap, struct ata_device *dev)
@@ -1947,10 +2098,13 @@ static void ata_dev_set_xfermode(struct ata_port *ap, struct ata_device *dev)
 }
 
 /**
- *      ata_sg_clean -
- *      @qc:
+ *      ata_sg_clean - Unmap DMA memory associated with command
+ *      @qc: Command containing DMA memory to be released
+ *
+ *      Unmap all mapped DMA memory associated with this command.
  *
  *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
  */
 
 static void ata_sg_clean(struct ata_queued_cmd *qc)
@@ -1981,7 +2135,11 @@ static void ata_sg_clean(struct ata_queued_cmd *qc)
  *      ata_fill_sg - Fill PCI IDE PRD table
  *      @qc: Metadata associated with taskfile to be transferred
  *
+ *      Fill PCI IDE PRD (scatter-gather) table with segments
+ *      associated with the current disk command.
+ *
  *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
  *
  */
 static void ata_fill_sg(struct ata_queued_cmd *qc)
@@ -2028,7 +2186,13 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
  *      ata_check_atapi_dma - Check whether ATAPI DMA can be supported
  *      @qc: Metadata associated with taskfile to check
  *
+ *      Allow low-level driver to filter ATA PACKET commands, returning
+ *      a status indicating whether or not it is OK to use DMA for the
+ *      supplied PACKET command.
+ *
  *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ *
  *      RETURNS: 0 when ATAPI DMA can be used
  *               nonzero otherwise
  */
@@ -2046,6 +2210,8 @@ int ata_check_atapi_dma(struct ata_queued_cmd *qc)
  *      ata_qc_prep - Prepare taskfile for submission
  *      @qc: Metadata associated with taskfile to be prepared
  *
+ *      Prepare ATA taskfile for submission.
+ *
  *      LOCKING:
  *      spin_lock_irqsave(host_set lock)
  */
@@ -2057,6 +2223,32 @@ void ata_qc_prep(struct ata_queued_cmd *qc)
         ata_fill_sg(qc);
 }
 
+/**
+ *      ata_sg_init_one - Associate command with memory buffer
+ *      @qc: Command to be associated
+ *      @buf: Memory buffer
+ *      @buflen: Length of memory buffer, in bytes.
+ *
+ *      Initialize the data-related elements of queued_cmd @qc
+ *      to point to a single memory buffer, @buf of byte length @buflen.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
+
+
+
+/**
+ *      ata_sg_init_one - Prepare a one-entry scatter-gather list.
+ *      @qc:  Queued command
+ *      @buf:  transfer buffer
+ *      @buflen:  length of buf
+ *
+ *      Builds a single-entry scatter-gather list to initiate a
+ *      transfer utilizing the specified buffer.
+ *
+ *      LOCKING:
+ */
 void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
 {
         struct scatterlist *sg;
@@ -2074,6 +2266,32 @@ void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
         sg->length = buflen;
 }
 
+/**
+ *      ata_sg_init - Associate command with scatter-gather table.
+ *      @qc: Command to be associated
+ *      @sg: Scatter-gather table.
+ *      @n_elem: Number of elements in s/g table.
+ *
+ *      Initialize the data-related elements of queued_cmd @qc
+ *      to point to a scatter-gather table @sg, containing @n_elem
+ *      elements.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
+
+
+/**
+ *      ata_sg_init - Assign a scatter gather list to a queued command
+ *      @qc:  Queued command
+ *      @sg:  Scatter-gather list
+ *      @n_elem:  length of sg list
+ *
+ *      Attaches a scatter-gather list to a queued command.
+ *
+ *      LOCKING:
+ */
+
 void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
                  unsigned int n_elem)
 {
@@ -2083,14 +2301,16 @@ void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
 }
 
 /**
- *      ata_sg_setup_one -
- *      @qc:
+ *      ata_sg_setup_one - DMA-map the memory buffer associated with a command.
+ *      @qc: Command with memory buffer to be mapped.
+ *
+ *      DMA-map the memory buffer associated with queued_cmd @qc.
  *
  *      LOCKING:
  *      spin_lock_irqsave(host_set lock)
  *
  *      RETURNS:
- *
+ *      Zero on success, negative on error.
  */
 
 static int ata_sg_setup_one(struct ata_queued_cmd *qc)
@@ -2115,13 +2335,16 @@ static int ata_sg_setup_one(struct ata_queued_cmd *qc)
 }
 
 /**
- *      ata_sg_setup -
- *      @qc:
+ *      ata_sg_setup - DMA-map the scatter-gather table associated with a command.
+ *      @qc: Command with scatter-gather table to be mapped.
+ *
+ *      DMA-map the scatter-gather table associated with queued_cmd @qc.
  *
  *      LOCKING:
  *      spin_lock_irqsave(host_set lock)
  *
  *      RETURNS:
+ *      Zero on success, negative on error.
  *
  */
 
@@ -2151,6 +2374,7 @@ static int ata_sg_setup(struct ata_queued_cmd *qc)
  *      @ap:
  *
  *      LOCKING:
+ *      None.  (executing in kernel thread context)
  *
  *      RETURNS:
  *
@@ -2198,6 +2422,7 @@ static unsigned long ata_pio_poll(struct ata_port *ap)
  *      @ap:
  *
  *      LOCKING:
+ *      None.  (executing in kernel thread context)
  */
 
 static void ata_pio_complete (struct ata_port *ap)
@@ -2240,6 +2465,18 @@ static void ata_pio_complete (struct ata_port *ap)
         ata_qc_complete(qc, drv_stat);
 }
 
+
+/**
+ *      swap_buf_le16 -
+ *      @buf:  Buffer to swap
+ *      @buf_words:  Number of 16-bit words in buffer.
+ *
+ *      Swap halves of 16-bit words if needed to convert from
+ *      little-endian byte order to native cpu byte order, or
+ *      vice-versa.
+ *
+ *      LOCKING:
+ */
 void swap_buf_le16(u16 *buf, unsigned int buf_words)
 {
 #ifdef __BIG_ENDIAN
@@ -2415,6 +2652,7 @@ err_out:
  *      @ap:
  *
  *      LOCKING:
+ *      None.  (executing in kernel thread context)
  */
 
 static void ata_pio_block(struct ata_port *ap)
@@ -2583,6 +2821,7 @@ static void atapi_request_sense(struct ata_port *ap, struct ata_device *dev,
  *      transaction completed successfully.
  *
  *      LOCKING:
+ *      Inherited from SCSI layer (none, can sleep)
  */
 
 static void ata_qc_timeout(struct ata_queued_cmd *qc)
@@ -2692,6 +2931,7 @@ out:
  *      @dev: Device from whom we request an available command structure
  *
  *      LOCKING:
+ *      None.
  */
 
 static struct ata_queued_cmd *ata_qc_new(struct ata_port *ap)
@@ -2717,6 +2957,7 @@ static struct ata_queued_cmd *ata_qc_new(struct ata_port *ap)
  *      @dev: Device from whom we request an available command structure
  *
  *      LOCKING:
+ *      None.
  */
 
 struct ata_queued_cmd *ata_qc_new_init(struct ata_port *ap,
@@ -2781,6 +3022,7 @@ static void __ata_qc_complete(struct ata_queued_cmd *qc)
  *      in case something prevents using it.
  *
  *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
  *
  */
 void ata_qc_free(struct ata_queued_cmd *qc)
@@ -2794,9 +3036,13 @@ void ata_qc_free(struct ata_queued_cmd *qc)
 /**
  *      ata_qc_complete - Complete an active ATA command
  *      @qc: Command to complete
- *      @drv_stat: ATA status register contents
+ *      @drv_stat: ATA Status register contents
+ *
+ *      Indicate to the mid and upper layers that an ATA
+ *      command has completed, with either an ok or not-ok status.
  *
  *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
  *
  */
 
@@ -2892,6 +3138,7 @@ err_out:
         return -1;
 }
 
+
 /**
  *      ata_qc_issue_prot - issue taskfile to device in proto-dependent manner
  *      @qc: command to issue to device
@@ -2901,6 +3148,8 @@ err_out:
  *      classes called "protocols", and issuing each type of protocol
  *      is slightly different.
  *
+ *      May be used as the qc_issue() entry in ata_port_operations.
+ *
  *      LOCKING:
  *      spin_lock_irqsave(host_set lock)
  *
@@ -2958,7 +3207,7 @@ int ata_qc_issue_prot(struct ata_queued_cmd *qc)
 }
 
 /**
- *      ata_bmdma_setup - Set up PCI IDE BMDMA transaction
+ *      ata_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
@@ -3065,6 +3314,18 @@ static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
              ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
 }
 
+
+/**
+ *      ata_bmdma_start - Start a PCI IDE BMDMA transaction
+ *      @qc: Info associated with this ATA transaction.
+ *
+ *      Writes the ATA_DMA_START flag to the DMA command register.
+ *
+ *      May be used as the bmdma_start() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
 void ata_bmdma_start(struct ata_queued_cmd *qc)
 {
         if (qc->ap->flags & ATA_FLAG_MMIO)
@@ -3073,6 +3334,20 @@ void ata_bmdma_start(struct ata_queued_cmd *qc)
                 ata_bmdma_start_pio(qc);
 }
 
+
+/**
+ *      ata_bmdma_setup - Set up PCI IDE BMDMA transaction
+ *      @qc: Info associated with this ATA transaction.
+ *
+ *      Writes address of PRD table to device's PRD Table Address
+ *      register, sets the DMA control register, and calls
+ *      ops->exec_command() to start the transfer.
+ *
+ *      May be used as the bmdma_setup() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
 void ata_bmdma_setup(struct ata_queued_cmd *qc)
 {
         if (qc->ap->flags & ATA_FLAG_MMIO)
@@ -3081,6 +3356,19 @@ void ata_bmdma_setup(struct ata_queued_cmd *qc)
                 ata_bmdma_setup_pio(qc);
 }
 
+
+/**
+ *      ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ *      @ap: Port associated with this ATA transaction.
+ *
+ *      Clear interrupt and error flags in DMA status register.
+ *
+ *      May be used as the irq_clear() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
+
 void ata_bmdma_irq_clear(struct ata_port *ap)
 {
     if (ap->flags & ATA_FLAG_MMIO) {
@@ -3093,6 +3381,19 @@ void ata_bmdma_irq_clear(struct ata_port *ap)
 
 }
 
+
+/**
+ *      ata_bmdma_status - Read PCI IDE BMDMA status
+ *      @ap: Port associated with this ATA transaction.
+ *
+ *      Read and return BMDMA status register.
+ *
+ *      May be used as the bmdma_status() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
+
 u8 ata_bmdma_status(struct ata_port *ap)
 {
         u8 host_stat;
@@ -3104,6 +3405,19 @@ u8 ata_bmdma_status(struct ata_port *ap)
         return host_stat;
 }
 
+
+/**
+ *      ata_bmdma_stop - Stop PCI IDE BMDMA transfer
+ *      @ap: Port associated with this ATA transaction.
+ *
+ *      Clears the ATA_DMA_START flag in the dma control register
+ *
+ *      May be used as the bmdma_stop() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      spin_lock_irqsave(host_set lock)
+ */
+
 void ata_bmdma_stop(struct ata_port *ap)
 {
         if (ap->flags & ATA_FLAG_MMIO) {
@@ -3203,13 +3517,18 @@ idle_irq:
 
 /**
  *      ata_interrupt - Default ATA host interrupt handler
- *      @irq: irq line
- *      @dev_instance: pointer to our host information structure
+ *      @irq: irq line (unused)
+ *      @dev_instance: pointer to our ata_host_set information structure
  *      @regs: unused
  *
+ *      Default interrupt handler for PCI IDE devices.  Calls
+ *      ata_host_intr() for each port that is not disabled.
+ *
  *      LOCKING:
+ *      Obtains host_set lock during operation.
  *
  *      RETURNS:
+ *      IRQ_NONE or IRQ_HANDLED.
  *
  */
 
@@ -3302,6 +3621,19 @@ err_out:
         ata_qc_complete(qc, ATA_ERR);
 }
 
+
+/**
+ *      ata_port_start - Set port up for dma.
+ *      @ap: Port to initialize
+ *
+ *      Called just after data structures for each port are
+ *      initialized.  Allocates space for PRD table.
+ *
+ *      May be used as the port_start() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ */
+
 int ata_port_start (struct ata_port *ap)
 {
         struct device *dev = ap->host_set->dev;
@@ -3315,6 +3647,18 @@ int ata_port_start (struct ata_port *ap)
         return 0;
 }
 
+
+/**
+ *      ata_port_stop - Undo ata_port_start()
+ *      @ap: Port to shut down
+ *
+ *      Frees the PRD table.
+ *
+ *      May be used as the port_stop() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ */
+
 void ata_port_stop (struct ata_port *ap)
 {
         struct device *dev = ap->host_set->dev;
@@ -3357,7 +3701,11 @@ static void ata_host_remove(struct ata_port *ap, unsigned int do_unregister)
  *      @ent: Probe information provided by low-level driver
  *      @port_no: Port number associated with this ata_port
  *
+ *      Initialize a new ata_port structure, and its associated
+ *      scsi_host.
+ *
  *      LOCKING:
+ *      Inherited from caller.
  *
  */
 
@@ -3412,9 +3760,13 @@ static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
  *      @host_set: Collections of ports to which we add
  *      @port_no: Port number associated with this host
  *
+ *      Attach low-level ATA driver to system.
+ *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  *      RETURNS:
+ *      New ata_port on success, for NULL on error.
  *
  */
 
@@ -3447,12 +3799,22 @@ err_out:
 }
 
 /**
- *      ata_device_add -
- *      @ent:
+ *      ata_device_add - Register hardware device with ATA and SCSI layers
+ *      @ent: Probe information describing hardware device to be registered
+ *
+ *      This function processes the information provided in the probe
+ *      information struct @ent, allocates the necessary ATA and SCSI
+ *      host information structures, initializes them, and registers
+ *      everything with requisite kernel subsystems.
+ *
+ *      This function requests irqs, probes the ATA bus, and probes
+ *      the SCSI bus.
  *
  *      LOCKING:
+ *      PCI/etc. bus probe sem.
  *
  *      RETURNS:
+ *      Number of ports registered.  Zero on error (no ports registered).
  *
  */
 
@@ -3604,7 +3966,15 @@ int ata_scsi_release(struct Scsi_Host *host)
 /**
  *      ata_std_ports - initialize ioaddr with standard port offsets.
  *      @ioaddr: IO address structure to be initialized
+ *
+ *      Utility function which initializes data_addr, error_addr,
+ *      feature_addr, nsect_addr, lbal_addr, lbam_addr, lbah_addr,
+ *      device_addr, status_addr, and command_addr to standard offsets
+ *      relative to cmd_addr.
+ *
+ *      Does not set ctl_addr, altstatus_addr, bmdma_addr, or scr_addr.
  */
+
 void ata_std_ports(struct ata_ioports *ioaddr)
 {
         ioaddr->data_addr = ioaddr->cmd_addr + ATA_REG_DATA;
@@ -3646,6 +4016,20 @@ ata_probe_ent_alloc(struct device *dev, struct ata_port_info *port)
         return probe_ent;
 }
 
+
+
+/**
+ *      ata_pci_init_native_mode - Initialize native-mode driver
+ *      @pdev:  pci device to be initialized
+ *      @port:  array[2] of pointers to port info structures.
+ *
+ *      Utility function which allocates and initializes an
+ *      ata_probe_ent structure for a standard dual-port
+ *      PIO-based IDE controller.  The returned ata_probe_ent
+ *      structure can be passed to ata_device_add().  The returned
+ *      ata_probe_ent structure should then be freed with kfree().
+ */
+
 #ifdef CONFIG_PCI
 struct ata_probe_ent *
 ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port)
@@ -3727,10 +4111,19 @@ ata_pci_init_legacy_mode(struct pci_dev *pdev, struct ata_port_info **port,
  *      @port_info: Information from low-level host driver
  *      @n_ports: Number of ports attached to host controller
  *
+ *      This is a helper function which can be called from a driver's
+ *      xxx_init_one() probe function if the hardware uses traditional
+ *      IDE taskfile registers.
+ *
+ *      This function calls pci_enable_device(), reserves its register
+ *      regions, sets the dma mask, enables bus master mode, and calls
+ *      ata_device_add()
+ *
  *      LOCKING:
  *      Inherited from PCI layer (may sleep).
  *
  *      RETURNS:
+ *      Zero on success, negative on errno-based value on error.
  *
  */
 
@@ -3949,15 +4342,6 @@ int pci_test_config_bits(struct pci_dev *pdev, struct pci_bits *bits)
 #endif /* CONFIG_PCI */
 
 
-/**
- *      ata_init -
- *
- *      LOCKING:
- *
- *      RETURNS:
- *
- */
-
 static int __init ata_init(void)
 {
         ata_wq = create_workqueue("ata");
diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index 416ba67ba9ee..7a4adc4c8f09 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -947,7 +947,7 @@ unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
 }
 
 /**
- *      ata_scsiop_noop -
+ *      ata_scsiop_noop - Command handler that simply returns success.
  *      @args: device IDENTIFY data / SCSI command of interest.
  *      @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
  *      @buflen: Response buffer length.
diff --git a/include/linux/libata.h b/include/linux/libata.h
index e74f301e9bae..b009f801e7c5 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -467,12 +467,34 @@ static inline u8 ata_chk_status(struct ata_port *ap)
         return ap->ops->check_status(ap);
 }
 
+
+/**
+ *      ata_pause - Flush writes and pause 400 nanoseconds.
+ *      @ap: Port to wait for.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+
 static inline void ata_pause(struct ata_port *ap)
 {
         ata_altstatus(ap);
         ndelay(400);
 }
 
+
+/**
+ *      ata_busy_wait - Wait for a port status register
+ *      @ap: Port to wait for.
+ *
+ *      Waits up to max*10 microseconds for the selected bits in the port's
+ *      status register to be cleared.
+ *      Returns final value of status register.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+
 static inline u8 ata_busy_wait(struct ata_port *ap, unsigned int bits,
                                unsigned int max)
 {
@@ -487,6 +509,18 @@ static inline u8 ata_busy_wait(struct ata_port *ap, unsigned int bits,
         return status;
 }
 
+
+/**
+ *      ata_wait_idle - Wait for a port to be idle.
+ *      @ap: Port to wait for.
+ *
+ *      Waits up to 10ms for port's BUSY and DRQ signals to clear.
+ *      Returns final value of status register.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+
 static inline u8 ata_wait_idle(struct ata_port *ap)
 {
         u8 status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
@@ -525,6 +559,18 @@ static inline void ata_tf_init(struct ata_port *ap, struct ata_taskfile *tf, uns
                 tf->device = ATA_DEVICE_OBS | ATA_DEV1;
 }
 
+
+/**
+ *      ata_irq_on - Enable interrupts on a port.
+ *      @ap: Port on which interrupts are enabled.
+ *
+ *      Enable interrupts on a legacy IDE device using MMIO or PIO,
+ *      wait for idle, clear any pending interrupts.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+
 static inline u8 ata_irq_on(struct ata_port *ap)
 {
         struct ata_ioports *ioaddr = &ap->ioaddr;
@@ -544,6 +590,18 @@ static inline u8 ata_irq_on(struct ata_port *ap)
         return tmp;
 }
 
+
+/**
+ *      ata_irq_ack - Acknowledge a device interrupt.
+ *      @ap: Port on which interrupts are enabled.
+ *
+ *      Wait up to 10 ms for legacy IDE device to become idle (BUSY
+ *      or BUSY+DRQ clear).  Obtain dma status and port status from
+ *      device.  Clear the interrupt.  Return port status.
+ *
+ *      LOCKING:
+ */
+
 static inline u8 ata_irq_ack(struct ata_port *ap, unsigned int chk_drq)
 {
         unsigned int bits = chk_drq ? ATA_BUSY | ATA_DRQ : ATA_BUSY;