aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorSteve Glendinning <steve.glendinning@smsc.com>2008-11-04 19:35:37 -0500
committerJeff Garzik <jgarzik@redhat.com>2008-11-06 00:58:40 -0500
commitfd9abb3d97c2ab883e4732ec1214fe64190236e7 (patch)
treee5f9c0b1ab77980e22434c85cf50644e18c1e134
parentc5916cf8dbd3ac5ec675d9347aeaa796b546b50e (diff)
SMSC LAN911x and LAN921x vendor driver
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded ethernet controllers. There is an existing smc911x driver in the tree; this is intended to replace it. Dustin McIntire (the author of the smc911x driver) has expressed his support for switching to this driver. This driver contains workarounds for all known hardware issues, and has been tested on all flavours of the chip on multiple architectures. This driver now uses phylib, so this patch also adds support for the device's internal phy Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com> Signed-off-by: Dustin Mcintire <dustin@sensoria.com> Signed-off-by: Bill Gatliff <bgat@billgatliff.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Diffstat
-rw-r--r--MAINTAINERS6
-rw-r--r--drivers/net/Kconfig14
-rw-r--r--drivers/net/Makefile1
-rw-r--r--drivers/net/phy/smsc.c28
-rw-r--r--drivers/net/smsc911x.c2091
-rw-r--r--drivers/net/smsc911x.h394
-rw-r--r--include/linux/smsc911x.h42
7 files changed, 2576 insertions, 0 deletions
diff --git a/MAINTAINERS b/MAINTAINERS
index 129117fe6490..5d951f3db018 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3853,6 +3853,12 @@ M: mhoffman@lightlink.com
3853L: lm-sensors@lm-sensors.org 3853L: lm-sensors@lm-sensors.org
3854S: Maintained 3854S: Maintained
3855 3855
3856SMSC911x ETHERNET DRIVER
3857P: Steve Glendinning
3858M: steve.glendinning@smsc.com
3859L: netdev@vger.kernel.org
3860S: Supported
3861
3856SMX UIO Interface 3862SMX UIO Interface
3857P: Ben Nizette 3863P: Ben Nizette
3858M: bn@niasdigital.com 3864M: bn@niasdigital.com
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index f1d0a1371695..74a18a7f8f40 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -979,6 +979,20 @@ config SMC911X
979 called smc911x. If you want to compile it as a module, say M 979 called smc911x. If you want to compile it as a module, say M
980 here and read <file:Documentation/kbuild/modules.txt> 980 here and read <file:Documentation/kbuild/modules.txt>
981 981
982config SMSC911X
983 tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
984 depends on ARM || SUPERH
985 select CRC32
986 select MII
987 select PHYLIB
988 ---help---
989 Say Y here if you want support for SMSC LAN911x and LAN921x families
990 of ethernet controllers.
991
992 To compile this driver as a module, choose M here and read
993 <file:Documentation/networking/net-modules.txt>. The module
994 will be called smsc911x.
995
982config NET_VENDOR_RACAL 996config NET_VENDOR_RACAL
983 bool "Racal-Interlan (Micom) NI cards" 997 bool "Racal-Interlan (Micom) NI cards"
984 depends on ISA 998 depends on ISA
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 657c47b1a6b6..e06829aa75b0 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -219,6 +219,7 @@ obj-$(CONFIG_S2IO) += s2io.o
219obj-$(CONFIG_MYRI10GE) += myri10ge/ 219obj-$(CONFIG_MYRI10GE) += myri10ge/
220obj-$(CONFIG_SMC91X) += smc91x.o 220obj-$(CONFIG_SMC91X) += smc91x.o
221obj-$(CONFIG_SMC911X) += smc911x.o 221obj-$(CONFIG_SMC911X) += smc911x.o
222obj-$(CONFIG_SMSC911X) += smsc911x.o
222obj-$(CONFIG_BFIN_MAC) += bfin_mac.o 223obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
223obj-$(CONFIG_DM9000) += dm9000.o 224obj-$(CONFIG_DM9000) += dm9000.o
224obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o 225obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index 73baa7a3bb0e..c05d38d46350 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -126,6 +126,27 @@ static struct phy_driver lan8700_driver = {
126 .driver = { .owner = THIS_MODULE, } 126 .driver = { .owner = THIS_MODULE, }
127}; 127};
128 128
129static struct phy_driver lan911x_int_driver = {
130 .phy_id = 0x0007c0d0, /* OUI=0x00800f, Model#=0x0d */
131 .phy_id_mask = 0xfffffff0,
132 .name = "SMSC LAN911x Internal PHY",
133
134 .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause
135 | SUPPORTED_Asym_Pause),
136 .flags = PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
137
138 /* basic functions */
139 .config_aneg = genphy_config_aneg,
140 .read_status = genphy_read_status,
141 .config_init = smsc_phy_config_init,
142
143 /* IRQ related */
144 .ack_interrupt = smsc_phy_ack_interrupt,
145 .config_intr = smsc_phy_config_intr,
146
147 .driver = { .owner = THIS_MODULE, }
148};
149
129static int __init smsc_init(void) 150static int __init smsc_init(void)
130{ 151{
131 int ret; 152 int ret;
@@ -142,8 +163,14 @@ static int __init smsc_init(void)
142 if (ret) 163 if (ret)
143 goto err3; 164 goto err3;
144 165
166 ret = phy_driver_register (&lan911x_int_driver);
167 if (ret)
168 goto err4;
169
145 return 0; 170 return 0;
146 171
172err4:
173 phy_driver_unregister (&lan8700_driver);
147err3: 174err3:
148 phy_driver_unregister (&lan8187_driver); 175 phy_driver_unregister (&lan8187_driver);
149err2: 176err2:
@@ -154,6 +181,7 @@ err1:
154 181
155static void __exit smsc_exit(void) 182static void __exit smsc_exit(void)
156{ 183{
184 phy_driver_unregister (&lan911x_int_driver);
157 phy_driver_unregister (&lan8700_driver); 185 phy_driver_unregister (&lan8700_driver);
158 phy_driver_unregister (&lan8187_driver); 186 phy_driver_unregister (&lan8187_driver);
159 phy_driver_unregister (&lan83c185_driver); 187 phy_driver_unregister (&lan83c185_driver);
diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
new file mode 100644
index 000000000000..fe517880fc97
--- /dev/null
+++ b/drivers/net/smsc911x.c
@@ -0,0 +1,2091 @@
1/***************************************************************************
2 *
3 * Copyright (C) 2004-2008 SMSC
4 * Copyright (C) 2005-2008 ARM
5 *
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License
8 * as published by the Free Software Foundation; either version 2
9 * of the License, or (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
19 *
20 ***************************************************************************
21 * Rewritten, heavily based on smsc911x simple driver by SMSC.
22 * Partly uses io macros from smc91x.c by Nicolas Pitre
23 *
24 * Supported devices:
25 * LAN9115, LAN9116, LAN9117, LAN9118
26 * LAN9215, LAN9216, LAN9217, LAN9218
27 * LAN9210, LAN9211
28 * LAN9220, LAN9221
29 *
30 */
31
32#include <linux/crc32.h>
33#include <linux/delay.h>
34#include <linux/errno.h>
35#include <linux/etherdevice.h>
36#include <linux/ethtool.h>
37#include <linux/init.h>
38#include <linux/ioport.h>
39#include <linux/kernel.h>
40#include <linux/module.h>
41#include <linux/netdevice.h>
42#include <linux/platform_device.h>
43#include <linux/sched.h>
44#include <linux/slab.h>
45#include <linux/timer.h>
46#include <linux/version.h>
47#include <linux/bug.h>
48#include <linux/bitops.h>
49#include <linux/irq.h>
50#include <linux/io.h>
51#include <linux/phy.h>
52#include <linux/smsc911x.h>
53#include "smsc911x.h"
54
55#define SMSC_CHIPNAME "smsc911x"
56#define SMSC_MDIONAME "smsc911x-mdio"
57#define SMSC_DRV_VERSION "2008-10-21"
58
59MODULE_LICENSE("GPL");
60MODULE_VERSION(SMSC_DRV_VERSION);
61
62#if USE_DEBUG > 0
63static int debug = 16;
64#else
65static int debug = 3;
66#endif
67
68module_param(debug, int, 0);
69MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
70
71struct smsc911x_data {
72 void __iomem *ioaddr;
73
74 unsigned int idrev;
75
76 /* used to decide which workarounds apply */
77 unsigned int generation;
78
79 /* device configuration (copied from platform_data during probe) */
80 unsigned int irq_polarity;
81 unsigned int irq_type;
82 phy_interface_t phy_interface;
83
84 /* This needs to be acquired before calling any of below:
85 * smsc911x_mac_read(), smsc911x_mac_write()
86 */
87 spinlock_t mac_lock;
88
89#if (!SMSC_CAN_USE_32BIT)
90 /* spinlock to ensure 16-bit accesses are serialised */
91 spinlock_t dev_lock;
92#endif
93
94 struct phy_device *phy_dev;
95 struct mii_bus *mii_bus;
96 int phy_irq[PHY_MAX_ADDR];
97 unsigned int using_extphy;
98 int last_duplex;
99 int last_carrier;
100
101 u32 msg_enable;
102 unsigned int gpio_setting;
103 unsigned int gpio_orig_setting;
104 struct net_device *dev;
105 struct napi_struct napi;
106
107 unsigned int software_irq_signal;
108
109#ifdef USE_PHY_WORK_AROUND
110#define MIN_PACKET_SIZE (64)
111 char loopback_tx_pkt[MIN_PACKET_SIZE];
112 char loopback_rx_pkt[MIN_PACKET_SIZE];
113 unsigned int resetcount;
114#endif
115
116 /* Members for Multicast filter workaround */
117 unsigned int multicast_update_pending;
118 unsigned int set_bits_mask;
119 unsigned int clear_bits_mask;
120 unsigned int hashhi;
121 unsigned int hashlo;
122};
123
124#if SMSC_CAN_USE_32BIT
125
126static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
127{
128 return readl(pdata->ioaddr + reg);
129}
130
131static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
132 u32 val)
133{
134 writel(val, pdata->ioaddr + reg);
135}
136
137/* Writes a packet to the TX_DATA_FIFO */
138static inline void
139smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
140 unsigned int wordcount)
141{
142 writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
143}
144
145/* Reads a packet out of the RX_DATA_FIFO */
146static inline void
147smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
148 unsigned int wordcount)
149{
150 readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
151}
152
153#else /* SMSC_CAN_USE_32BIT */
154
155/* These 16-bit access functions are significantly slower, due to the locking
156 * necessary. If your bus hardware can be configured to do this for you
157 * (in response to a single 32-bit operation from software), you should use
158 * the 32-bit access functions instead. */
159
160static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
161{
162 unsigned long flags;
163 u32 data;
164
165 /* these two 16-bit reads must be performed consecutively, so must
166 * not be interrupted by our own ISR (which would start another
167 * read operation) */
168 spin_lock_irqsave(&pdata->dev_lock, flags);
169 data = ((readw(pdata->ioaddr + reg) & 0xFFFF) |
170 ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
171 spin_unlock_irqrestore(&pdata->dev_lock, flags);
172
173 return data;
174}
175
176static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
177 u32 val)
178{
179 unsigned long flags;
180
181 /* these two 16-bit writes must be performed consecutively, so must
182 * not be interrupted by our own ISR (which would start another
183 * read operation) */
184 spin_lock_irqsave(&pdata->dev_lock, flags);
185 writew(val & 0xFFFF, pdata->ioaddr + reg);
186 writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
187 spin_unlock_irqrestore(&pdata->dev_lock, flags);
188}
189
190/* Writes a packet to the TX_DATA_FIFO */
191static inline void
192smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
193 unsigned int wordcount)
194{
195 while (wordcount--)
196 smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++);
197}
198
199/* Reads a packet out of the RX_DATA_FIFO */
200static inline void
201smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
202 unsigned int wordcount)
203{
204 while (wordcount--)
205 *buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO);
206}
207
208#endif /* SMSC_CAN_USE_32BIT */
209
210/* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read
211 * and smsc911x_mac_write, so assumes mac_lock is held */
212static int smsc911x_mac_complete(struct smsc911x_data *pdata)
213{
214 int i;
215 u32 val;
216
217 SMSC_ASSERT_MAC_LOCK(pdata);
218
219 for (i = 0; i < 40; i++) {
220 val = smsc911x_reg_read(pdata, MAC_CSR_CMD);
221 if (!(val & MAC_CSR_CMD_CSR_BUSY_))
222 return 0;
223 }
224 SMSC_WARNING(HW, "Timed out waiting for MAC not BUSY. "
225 "MAC_CSR_CMD: 0x%08X", val);
226 return -EIO;
227}
228
229/* Fetches a MAC register value. Assumes mac_lock is acquired */
230static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset)
231{
232 unsigned int temp;
233
234 SMSC_ASSERT_MAC_LOCK(pdata);
235
236 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD);
237 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) {
238 SMSC_WARNING(HW, "MAC busy at entry");
239 return 0xFFFFFFFF;
240 }
241
242 /* Send the MAC cmd */
243 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) |
244 MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_));
245
246 /* Workaround for hardware read-after-write restriction */
247 temp = smsc911x_reg_read(pdata, BYTE_TEST);
248
249 /* Wait for the read to complete */
250 if (likely(smsc911x_mac_complete(pdata) == 0))
251 return smsc911x_reg_read(pdata, MAC_CSR_DATA);
252
253 SMSC_WARNING(HW, "MAC busy after read");
254 return 0xFFFFFFFF;
255}
256
257/* Set a mac register, mac_lock must be acquired before calling */
258static void smsc911x_mac_write(struct smsc911x_data *pdata,
259 unsigned int offset, u32 val)
260{
261 unsigned int temp;
262
263 SMSC_ASSERT_MAC_LOCK(pdata);
264
265 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD);
266 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) {
267 SMSC_WARNING(HW,
268 "smsc911x_mac_write failed, MAC busy at entry");
269 return;
270 }
271
272 /* Send data to write */
273 smsc911x_reg_write(pdata, MAC_CSR_DATA, val);
274
275 /* Write the actual data */
276 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) |
277 MAC_CSR_CMD_CSR_BUSY_));
278
279 /* Workaround for hardware read-after-write restriction */
280 temp = smsc911x_reg_read(pdata, BYTE_TEST);
281
282 /* Wait for the write to complete */
283 if (likely(smsc911x_mac_complete(pdata) == 0))
284 return;
285
286 SMSC_WARNING(HW,
287 "smsc911x_mac_write failed, MAC busy after write");
288}
289
290/* Get a phy register */
291static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx)
292{
293 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv;
294 unsigned long flags;
295 unsigned int addr;
296 int i, reg;
297
298 spin_lock_irqsave(&pdata->mac_lock, flags);
299
300 /* Confirm MII not busy */
301 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
302 SMSC_WARNING(HW,
303 "MII is busy in smsc911x_mii_read???");
304 reg = -EIO;
305 goto out;
306 }
307
308 /* Set the address, index & direction (read from PHY) */
309 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6);
310 smsc911x_mac_write(pdata, MII_ACC, addr);
311
312 /* Wait for read to complete w/ timeout */
313 for (i = 0; i < 100; i++)
314 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
315 reg = smsc911x_mac_read(pdata, MII_DATA);
316 goto out;
317 }
318
319 SMSC_WARNING(HW, "Timed out waiting for MII write to finish");
320 reg = -EIO;
321
322out:
323 spin_unlock_irqrestore(&pdata->mac_lock, flags);
324 return reg;
325}
326
327/* Set a phy register */
328static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx,
329 u16 val)
330{
331 struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv;
332 unsigned long flags;
333 unsigned int addr;
334 int i, reg;
335
336 spin_lock_irqsave(&pdata->mac_lock, flags);
337
338 /* Confirm MII not busy */
339 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
340 SMSC_WARNING(HW,
341 "MII is busy in smsc911x_mii_write???");
342 reg = -EIO;
343 goto out;
344 }
345
346 /* Put the data to write in the MAC */
347 smsc911x_mac_write(pdata, MII_DATA, val);
348
349 /* Set the address, index & direction (write to PHY) */
350 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) |
351 MII_ACC_MII_WRITE_;
352 smsc911x_mac_write(pdata, MII_ACC, addr);
353
354 /* Wait for write to complete w/ timeout */
355 for (i = 0; i < 100; i++)
356 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) {
357 reg = 0;
358 goto out;
359 }
360
361 SMSC_WARNING(HW, "Timed out waiting for MII write to finish");
362 reg = -EIO;
363
364out:
365 spin_unlock_irqrestore(&pdata->mac_lock, flags);
366 return reg;
367}
368
369/* Autodetects and initialises external phy for SMSC9115 and SMSC9117 flavors.
370 * If something goes wrong, returns -ENODEV to revert back to internal phy.
371 * Performed at initialisation only, so interrupts are enabled */
372static int smsc911x_phy_initialise_external(struct smsc911x_data *pdata)
373{
374 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG);
375
376 /* External phy is requested, supported, and detected */
377 if (hwcfg & HW_CFG_EXT_PHY_DET_) {
378
379 /* Switch to external phy. Assuming tx and rx are stopped
380 * because smsc911x_phy_initialise is called before
381 * smsc911x_rx_initialise and tx_initialise. */
382
383 /* Disable phy clocks to the MAC */
384 hwcfg &= (~HW_CFG_PHY_CLK_SEL_);
385 hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_;
386 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
387 udelay(10); /* Enough time for clocks to stop */
388
389 /* Switch to external phy */
390 hwcfg |= HW_CFG_EXT_PHY_EN_;
391 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
392
393 /* Enable phy clocks to the MAC */
394 hwcfg &= (~HW_CFG_PHY_CLK_SEL_);
395 hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_;
396 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
397 udelay(10); /* Enough time for clocks to restart */
398
399 hwcfg |= HW_CFG_SMI_SEL_;
400 smsc911x_reg_write(pdata, HW_CFG, hwcfg);
401
402 SMSC_TRACE(HW, "Successfully switched to external PHY");
403 pdata->using_extphy = 1;
404 } else {
405 SMSC_WARNING(HW, "No external PHY detected, "
406 "Using internal PHY instead.");
407 /* Use internal phy */
408 return -ENODEV;
409 }
410 return 0;
411}
412
413/* Fetches a tx status out of the status fifo */
414static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata)
415{
416 unsigned int result =
417 smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_;
418
419 if (result != 0)
420 result = smsc911x_reg_read(pdata, TX_STATUS_FIFO);
421
422 return result;
423}
424
425/* Fetches the next rx status */
426static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata)
427{
428 unsigned int result =
429 smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_;
430
431 if (result != 0)
432 result = smsc911x_reg_read(pdata, RX_STATUS_FIFO);
433
434 return result;
435}
436
437#ifdef USE_PHY_WORK_AROUND
438static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata)
439{
440 unsigned int tries;
441 u32 wrsz;
442 u32 rdsz;
443 ulong bufp;
444
445 for (tries = 0; tries < 10; tries++) {
446 unsigned int txcmd_a;
447 unsigned int txcmd_b;
448 unsigned int status;
449 unsigned int pktlength;
450 unsigned int i;
451
452 /* Zero-out rx packet memory */
453 memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE);
454
455 /* Write tx packet to 118 */
456 txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16;
457 txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_;
458 txcmd_a |= MIN_PACKET_SIZE;
459
460 txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE;
461
462 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a);
463 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b);
464
465 bufp = (ulong)pdata->loopback_tx_pkt & (~0x3);
466 wrsz = MIN_PACKET_SIZE + 3;
467 wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3);
468 wrsz >>= 2;
469
470 smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz);
471
472 /* Wait till transmit is done */
473 i = 60;
474 do {
475 udelay(5);
476 status = smsc911x_tx_get_txstatus(pdata);
477 } while ((i--) && (!status));
478
479 if (!status) {
480 SMSC_WARNING(HW, "Failed to transmit "
481 "during loopback test");
482 continue;
483 }
484 if (status & TX_STS_ES_) {
485 SMSC_WARNING(HW, "Transmit encountered "
486 "errors during loopback test");
487 continue;
488 }
489
490 /* Wait till receive is done */
491 i = 60;
492 do {
493 udelay(5);
494 status = smsc911x_rx_get_rxstatus(pdata);
495 } while ((i--) && (!status));
496
497 if (!status) {
498 SMSC_WARNING(HW,
499 "Failed to receive during loopback test");
500 continue;
501 }
502 if (status & RX_STS_ES_) {
503 SMSC_WARNING(HW, "Receive encountered "
504 "errors during loopback test");
505 continue;
506 }
507
508 pktlength = ((status & 0x3FFF0000UL) >> 16);
509 bufp = (ulong)pdata->loopback_rx_pkt;
510 rdsz = pktlength + 3;
511 rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3);
512 rdsz >>= 2;
513
514 smsc911x_rx_readfifo(pdata, (unsigned int *)bufp, rdsz);
515
516 if (pktlength != (MIN_PACKET_SIZE + 4)) {
517 SMSC_WARNING(HW, "Unexpected packet size "
518 "during loop back test, size=%d, will retry",
519 pktlength);
520 } else {
521 unsigned int j;
522 int mismatch = 0;
523 for (j = 0; j < MIN_PACKET_SIZE; j++) {
524 if (pdata->loopback_tx_pkt[j]
525 != pdata->loopback_rx_pkt[j]) {
526 mismatch = 1;
527 break;
528 }
529 }
530 if (!mismatch) {
531 SMSC_TRACE(HW, "Successfully verified "
532 "loopback packet");
533 return 0;
534 } else {
535 SMSC_WARNING(HW, "Data mismatch "
536 "during loop back test, will retry");
537 }
538 }
539 }
540
541 return -EIO;
542}
543
544static int smsc911x_phy_reset(struct smsc911x_data *pdata)
545{
546 struct phy_device *phy_dev = pdata->phy_dev;
547 unsigned int temp;
548 unsigned int i = 100000;
549
550 BUG_ON(!phy_dev);
551 BUG_ON(!phy_dev->bus);
552
553 SMSC_TRACE(HW, "Performing PHY BCR Reset");
554 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, BMCR_RESET);
555 do {
556 msleep(1);
557 temp = smsc911x_mii_read(phy_dev->bus, phy_dev->addr,
558 MII_BMCR);
559 } while ((i--) && (temp & BMCR_RESET));
560
561 if (temp & BMCR_RESET) {
562 SMSC_WARNING(HW, "PHY reset failed to complete.");
563 return -EIO;
564 }
565 /* Extra delay required because the phy may not be completed with
566 * its reset when BMCR_RESET is cleared. Specs say 256 uS is
567 * enough delay but using 1ms here to be safe */
568 msleep(1);
569
570 return 0;
571}
572
573static int smsc911x_phy_loopbacktest(struct net_device *dev)
574{
575 struct smsc911x_data *pdata = netdev_priv(dev);
576 struct phy_device *phy_dev = pdata->phy_dev;
577 int result = -EIO;
578 unsigned int i, val;
579 unsigned long flags;
580
581 /* Initialise tx packet using broadcast destination address */
582 memset(pdata->loopback_tx_pkt, 0xff, ETH_ALEN);
583
584 /* Use incrementing source address */
585 for (i = 6; i < 12; i++)
586 pdata->loopback_tx_pkt[i] = (char)i;
587
588 /* Set length type field */
589 pdata->loopback_tx_pkt[12] = 0x00;
590 pdata->loopback_tx_pkt[13] = 0x00;
591
592 for (i = 14; i < MIN_PACKET_SIZE; i++)
593 pdata->loopback_tx_pkt[i] = (char)i;
594
595 val = smsc911x_reg_read(pdata, HW_CFG);
596 val &= HW_CFG_TX_FIF_SZ_;
597 val |= HW_CFG_SF_;
598 smsc911x_reg_write(pdata, HW_CFG, val);
599
600 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_);
601 smsc911x_reg_write(pdata, RX_CFG,
602 (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8);
603
604 for (i = 0; i < 10; i++) {
605 /* Set PHY to 10/FD, no ANEG, and loopback mode */
606 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR,
607 BMCR_LOOPBACK | BMCR_FULLDPLX);
608
609 /* Enable MAC tx/rx, FD */
610 spin_lock_irqsave(&pdata->mac_lock, flags);
611 smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_
612 | MAC_CR_TXEN_ | MAC_CR_RXEN_);
613 spin_unlock_irqrestore(&pdata->mac_lock, flags);
614
615 if (smsc911x_phy_check_loopbackpkt(pdata) == 0) {
616 result = 0;
617 break;
618 }
619 pdata->resetcount++;
620
621 /* Disable MAC rx */
622 spin_lock_irqsave(&pdata->mac_lock, flags);
623 smsc911x_mac_write(pdata, MAC_CR, 0);
624 spin_unlock_irqrestore(&pdata->mac_lock, flags);
625
626 smsc911x_phy_reset(pdata);
627 }
628
629 /* Disable MAC */
630 spin_lock_irqsave(&pdata->mac_lock, flags);
631 smsc911x_mac_write(pdata, MAC_CR, 0);
632 spin_unlock_irqrestore(&pdata->mac_lock, flags);
633
634 /* Cancel PHY loopback mode */
635 smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, 0);
636
637 smsc911x_reg_write(pdata, TX_CFG, 0);
638 smsc911x_reg_write(pdata, RX_CFG, 0);
639
640 return result;
641}
642#endif /* USE_PHY_WORK_AROUND */
643
644static u8 smsc95xx_resolve_flowctrl_fulldplx(u16 lcladv, u16 rmtadv)
645{
646 u8 cap = 0;
647
648 if (lcladv & ADVERTISE_PAUSE_CAP) {
649 if (lcladv & ADVERTISE_PAUSE_ASYM) {
650 if (rmtadv & LPA_PAUSE_CAP)
651 cap = FLOW_CTRL_TX | FLOW_CTRL_RX;
652 else if (rmtadv & LPA_PAUSE_ASYM)
653 cap = FLOW_CTRL_RX;
654 } else {
655 if (rmtadv & LPA_PAUSE_CAP)
656 cap = FLOW_CTRL_TX | FLOW_CTRL_RX;
657 }
658 } else if (lcladv & ADVERTISE_PAUSE_ASYM) {
659 if ((rmtadv & LPA_PAUSE_CAP) && (rmtadv & LPA_PAUSE_ASYM))
660 cap = FLOW_CTRL_TX;
661 }
662
663 return cap;
664}
665
666static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata)
667{
668 struct phy_device *phy_dev = pdata->phy_dev;
669 u32 afc = smsc911x_reg_read(pdata, AFC_CFG);
670 u32 flow;
671 unsigned long flags;
672
673 if (phy_dev->duplex == DUPLEX_FULL) {
674 u16 lcladv = phy_read(phy_dev, MII_ADVERTISE);
675 u16 rmtadv = phy_read(phy_dev, MII_LPA);
676 u8 cap = smsc95xx_resolve_flowctrl_fulldplx(lcladv, rmtadv);
677
678 if (cap & FLOW_CTRL_RX)
679 flow = 0xFFFF0002;
680 else
681 flow = 0;
682
683 if (cap & FLOW_CTRL_TX)
684 afc |= 0xF;
685 else
686 afc &= ~0xF;
687
688 SMSC_TRACE(HW, "rx pause %s, tx pause %s",
689 (cap & FLOW_CTRL_RX ? "enabled" : "disabled"),
690 (cap & FLOW_CTRL_TX ? "enabled" : "disabled"));
691 } else {
692 SMSC_TRACE(HW, "half duplex");
693 flow = 0;
694 afc |= 0xF;
695 }
696
697 spin_lock_irqsave(&pdata->mac_lock, flags);
698 smsc911x_mac_write(pdata, FLOW, flow);
699 spin_unlock_irqrestore(&pdata->mac_lock, flags);
700
701 smsc911x_reg_write(pdata, AFC_CFG, afc);
702}
703
704/* Update link mode if anything has changed. Called periodically when the
705 * PHY is in polling mode, even if nothing has changed. */
706static void smsc911x_phy_adjust_link(struct net_device *dev)
707{
708 struct smsc911x_data *pdata = netdev_priv(dev);
709 struct phy_device *phy_dev = pdata->phy_dev;
710 unsigned long flags;
711 int carrier;
712
713 if (phy_dev->duplex != pdata->last_duplex) {
714 unsigned int mac_cr;
715 SMSC_TRACE(HW, "duplex state has changed");
716
717 spin_lock_irqsave(&pdata->mac_lock, flags);
718 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
719 if (phy_dev->duplex) {
720 SMSC_TRACE(HW,
721 "configuring for full duplex mode");
722 mac_cr |= MAC_CR_FDPX_;
723 } else {
724 SMSC_TRACE(HW,
725 "configuring for half duplex mode");
726 mac_cr &= ~MAC_CR_FDPX_;
727 }
728 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
729 spin_unlock_irqrestore(&pdata->mac_lock, flags);
730
731 smsc911x_phy_update_flowcontrol(pdata);
732 pdata->last_duplex = phy_dev->duplex;
733 }
734
735 carrier = netif_carrier_ok(dev);
736 if (carrier != pdata->last_carrier) {
737 SMSC_TRACE(HW, "carrier state has changed");
738 if (carrier) {
739 SMSC_TRACE(HW, "configuring for carrier OK");
740 if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) &&
741 (!pdata->using_extphy)) {
742 /* Restore orginal GPIO configuration */
743 pdata->gpio_setting = pdata->gpio_orig_setting;
744 smsc911x_reg_write(pdata, GPIO_CFG,
745 pdata->gpio_setting);
746 }
747 } else {
748 SMSC_TRACE(HW, "configuring for no carrier");
749 /* Check global setting that LED1
750 * usage is 10/100 indicator */
751 pdata->gpio_setting = smsc911x_reg_read(pdata,
752 GPIO_CFG);
753 if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_)
754 && (!pdata->using_extphy)) {
755 /* Force 10/100 LED off, after saving
756 * orginal GPIO configuration */
757 pdata->gpio_orig_setting = pdata->gpio_setting;
758
759 pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_;
760 pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_
761 | GPIO_CFG_GPIODIR0_
762 | GPIO_CFG_GPIOD0_);
763 smsc911x_reg_write(pdata, GPIO_CFG,
764 pdata->gpio_setting);
765 }
766 }
767 pdata->last_carrier = carrier;
768 }
769}
770
771static int smsc911x_mii_probe(struct net_device *dev)
772{
773 struct smsc911x_data *pdata = netdev_priv(dev);
774 struct phy_device *phydev = NULL;
775 int phy_addr;
776
777 /* find the first phy */
778 for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) {
779 if (pdata->mii_bus->phy_map[phy_addr]) {
780 phydev = pdata->mii_bus->phy_map[phy_addr];
781 SMSC_TRACE(PROBE, "PHY %d: addr %d, phy_id 0x%08X",
782 phy_addr, phydev->addr, phydev->phy_id);
783 break;
784 }
785 }
786
787 if (!phydev) {
788 pr_err("%s: no PHY found\n", dev->name);
789 return -ENODEV;
790 }
791
792 phydev = phy_connect(dev, phydev->dev.bus_id,
793 &smsc911x_phy_adjust_link, 0, pdata->phy_interface);
794
795 if (IS_ERR(phydev)) {
796 pr_err("%s: Could not attach to PHY\n", dev->name);
797 return PTR_ERR(phydev);
798 }
799
800 pr_info("%s: attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
801 dev->name, phydev->drv->name, phydev->dev.bus_id, phydev->irq);
802
803 /* mask with MAC supported features */
804 phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
805 SUPPORTED_Asym_Pause);
806 phydev->advertising = phydev->supported;
807
808 pdata->phy_dev = phydev;
809 pdata->last_duplex = -1;
810 pdata->last_carrier = -1;
811
812#ifdef USE_PHY_WORK_AROUND
813 if (smsc911x_phy_loopbacktest(dev) < 0) {
814 SMSC_WARNING(HW, "Failed Loop Back Test");
815 return -ENODEV;
816 }
817 SMSC_TRACE(HW, "Passed Loop Back Test");
818#endif /* USE_PHY_WORK_AROUND */
819
820 SMSC_TRACE(HW, "phy initialised succesfully");
821 return 0;
822}
823
824static int __devinit smsc911x_mii_init(struct platform_device *pdev,
825 struct net_device *dev)
826{
827 struct smsc911x_data *pdata = netdev_priv(dev);
828 int err = -ENXIO, i;
829
830 pdata->mii_bus = mdiobus_alloc();
831 if (!pdata->mii_bus) {
832 err = -ENOMEM;
833 goto err_out_1;
834 }
835
836 pdata->mii_bus->name = SMSC_MDIONAME;
837 snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id);
838 pdata->mii_bus->priv = pdata;
839 pdata->mii_bus->read = smsc911x_mii_read;
840 pdata->mii_bus->write = smsc911x_mii_write;
841 pdata->mii_bus->irq = pdata->phy_irq;
842 for (i = 0; i < PHY_MAX_ADDR; ++i)
843 pdata->mii_bus->irq[i] = PHY_POLL;
844
845 pdata->mii_bus->parent = &pdev->dev;
846 dev_set_drvdata(&pdev->dev, &pdata->mii_bus);
847
848 pdata->using_extphy = 0;
849
850 switch (pdata->idrev & 0xFFFF0000) {
851 case 0x01170000:
852 case 0x01150000:
853 case 0x117A0000:
854 case 0x115A0000:
855 /* External PHY supported, try to autodetect */
856 if (smsc911x_phy_initialise_external(pdata) < 0) {
857 SMSC_TRACE(HW, "No external PHY detected, "
858 "using internal PHY");
859 }
860 break;
861 default:
862 SMSC_TRACE(HW, "External PHY is not supported, "
863 "using internal PHY");
864 break;
865 }
866
867 if (!pdata->using_extphy) {
868 /* Mask all PHYs except ID 1 (internal) */
869 pdata->mii_bus->phy_mask = ~(1 << 1);
870 }
871
872 if (mdiobus_register(pdata->mii_bus)) {
873 SMSC_WARNING(PROBE, "Error registering mii bus");
874 goto err_out_free_bus_2;
875 }
876
877 if (smsc911x_mii_probe(dev) < 0) {
878 SMSC_WARNING(PROBE, "Error registering mii bus");
879 goto err_out_unregister_bus_3;
880 }
881
882 return 0;
883
884err_out_unregister_bus_3:
885 mdiobus_unregister(pdata->mii_bus);
886err_out_free_bus_2:
887 mdiobus_free(pdata->mii_bus);
888err_out_1:
889 return err;
890}
891
892/* Gets the number of tx statuses in the fifo */
893static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata)
894{
895 return (smsc911x_reg_read(pdata, TX_FIFO_INF)
896 & TX_FIFO_INF_TSUSED_) >> 16;
897}
898
899/* Reads tx statuses and increments counters where necessary */
900static void smsc911x_tx_update_txcounters(struct net_device *dev)
901{
902 struct smsc911x_data *pdata = netdev_priv(dev);
903 unsigned int tx_stat;
904
905 while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) {
906 if (unlikely(tx_stat & 0x80000000)) {
907 /* In this driver the packet tag is used as the packet
908 * length. Since a packet length can never reach the
909 * size of 0x8000, this bit is reserved. It is worth
910 * noting that the "reserved bit" in the warning above
911 * does not reference a hardware defined reserved bit
912 * but rather a driver defined one.
913 */
914 SMSC_WARNING(HW,
915 "Packet tag reserved bit is high");
916 } else {
917 if (unlikely(tx_stat & 0x00008000)) {
918 dev->stats.tx_errors++;
919 } else {
920 dev->stats.tx_packets++;
921 dev->stats.tx_bytes += (tx_stat >> 16);
922 }
923 if (unlikely(tx_stat & 0x00000100)) {
924 dev->stats.collisions += 16;
925 dev->stats.tx_aborted_errors += 1;
926 } else {
927 dev->stats.collisions +=
928 ((tx_stat >> 3) & 0xF);
929 }
930 if (unlikely(tx_stat & 0x00000800))
931 dev->stats.tx_carrier_errors += 1;
932 if (unlikely(tx_stat & 0x00000200)) {
933 dev->stats.collisions++;
934 dev->stats.tx_aborted_errors++;
935 }
936 }
937 }
938}
939
940/* Increments the Rx error counters */
941static void
942smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat)
943{
944 int crc_err = 0;
945
946 if (unlikely(rxstat & 0x00008000)) {
947 dev->stats.rx_errors++;
948 if (unlikely(rxstat & 0x00000002)) {
949 dev->stats.rx_crc_errors++;
950 crc_err = 1;
951 }
952 }
953 if (likely(!crc_err)) {
954 if (unlikely((rxstat & 0x00001020) == 0x00001020)) {
955 /* Frame type indicates length,
956 * and length error is set */
957 dev->stats.rx_length_errors++;
958 }
959 if (rxstat & RX_STS_MCAST_)
960 dev->stats.multicast++;
961 }
962}
963
964/* Quickly dumps bad packets */
965static void
966smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktbytes)
967{
968 unsigned int pktwords = (pktbytes + NET_IP_ALIGN + 3) >> 2;
969
970 if (likely(pktwords >= 4)) {
971 unsigned int timeout = 500;
972 unsigned int val;
973 smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_);
974 do {
975 udelay(1);
976 val = smsc911x_reg_read(pdata, RX_DP_CTRL);
977 } while (timeout-- && (val & RX_DP_CTRL_RX_FFWD_));
978
979 if (unlikely(timeout == 0))
980 SMSC_WARNING(HW, "Timed out waiting for "
981 "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val);
982 } else {
983 unsigned int temp;
984 while (pktwords--)
985 temp = smsc911x_reg_read(pdata, RX_DATA_FIFO);
986 }
987}
988
989/* NAPI poll function */
990static int smsc911x_poll(struct napi_struct *napi, int budget)
991{
992 struct smsc911x_data *pdata =
993 container_of(napi, struct smsc911x_data, napi);
994 struct net_device *dev = pdata->dev;
995 int npackets = 0;
996
997 while (likely(netif_running(dev)) && (npackets < budget)) {
998 unsigned int pktlength;
999 unsigned int pktwords;
1000 struct sk_buff *skb;
1001 unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata);
1002
1003 if (!rxstat) {
1004 unsigned int temp;
1005 /* We processed all packets available. Tell NAPI it can
1006 * stop polling then re-enable rx interrupts */
1007 smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_);
1008 netif_rx_complete(dev, napi);
1009 temp = smsc911x_reg_read(pdata, INT_EN);
1010 temp |= INT_EN_RSFL_EN_;
1011 smsc911x_reg_write(pdata, INT_EN, temp);
1012 break;
1013 }
1014
1015 /* Count packet for NAPI scheduling, even if it has an error.
1016 * Error packets still require cycles to discard */
1017 npackets++;
1018
1019 pktlength = ((rxstat & 0x3FFF0000) >> 16);
1020 pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2;
1021 smsc911x_rx_counterrors(dev, rxstat);
1022
1023 if (unlikely(rxstat & RX_STS_ES_)) {
1024 SMSC_WARNING(RX_ERR,
1025 "Discarding packet with error bit set");
1026 /* Packet has an error, discard it and continue with
1027 * the next */
1028 smsc911x_rx_fastforward(pdata, pktwords);
1029 dev->stats.rx_dropped++;
1030 continue;
1031 }
1032
1033 skb = netdev_alloc_skb(dev, pktlength + NET_IP_ALIGN);
1034 if (unlikely(!skb)) {
1035 SMSC_WARNING(RX_ERR,
1036 "Unable to allocate skb for rx packet");
1037 /* Drop the packet and stop this polling iteration */
1038 smsc911x_rx_fastforward(pdata, pktwords);
1039 dev->stats.rx_dropped++;
1040 break;
1041 }
1042
1043 skb->data = skb->head;
1044 skb_reset_tail_pointer(skb);
1045
1046 /* Align IP on 16B boundary */
1047 skb_reserve(skb, NET_IP_ALIGN);
1048 skb_put(skb, pktlength - 4);
1049 smsc911x_rx_readfifo(pdata, (unsigned int *)skb->head,
1050 pktwords);
1051 skb->protocol = eth_type_trans(skb, dev);
1052 skb->ip_summed = CHECKSUM_NONE;
1053 netif_receive_skb(skb);
1054
1055 /* Update counters */
1056 dev->stats.rx_packets++;
1057 dev->stats.rx_bytes += (pktlength - 4);
1058 dev->last_rx = jiffies;
1059 }
1060
1061 /* Return total received packets */
1062 return npackets;
1063}
1064
1065/* Returns hash bit number for given MAC address
1066 * Example:
1067 * 01 00 5E 00 00 01 -> returns bit number 31 */
1068static unsigned int smsc911x_hash(char addr[ETH_ALEN])
1069{
1070 return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f;
1071}
1072
1073static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata)
1074{
1075 /* Performs the multicast & mac_cr update. This is called when
1076 * safe on the current hardware, and with the mac_lock held */
1077 unsigned int mac_cr;
1078
1079 SMSC_ASSERT_MAC_LOCK(pdata);
1080
1081 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
1082 mac_cr |= pdata->set_bits_mask;
1083 mac_cr &= ~(pdata->clear_bits_mask);
1084 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
1085 smsc911x_mac_write(pdata, HASHH, pdata->hashhi);
1086 smsc911x_mac_write(pdata, HASHL, pdata->hashlo);
1087 SMSC_TRACE(HW, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X",
1088 mac_cr, pdata->hashhi, pdata->hashlo);
1089}
1090
1091static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata)
1092{
1093 unsigned int mac_cr;
1094
1095 /* This function is only called for older LAN911x devices
1096 * (revA or revB), where MAC_CR, HASHH and HASHL should not
1097 * be modified during Rx - newer devices immediately update the
1098 * registers.
1099 *
1100 * This is called from interrupt context */
1101
1102 spin_lock(&pdata->mac_lock);
1103
1104 /* Check Rx has stopped */
1105 if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_)
1106 SMSC_WARNING(DRV, "Rx not stopped");
1107
1108 /* Perform the update - safe to do now Rx has stopped */
1109 smsc911x_rx_multicast_update(pdata);
1110
1111 /* Re-enable Rx */
1112 mac_cr = smsc911x_mac_read(pdata, MAC_CR);
1113 mac_cr |= MAC_CR_RXEN_;
1114 smsc911x_mac_write(pdata, MAC_CR, mac_cr);
1115
1116 pdata->multicast_update_pending = 0;
1117
1118 spin_unlock(&pdata->mac_lock);
1119}
1120
1121static int smsc911x_soft_reset(struct smsc911x_data *pdata)
1122{
1123 unsigned int timeout;
1124 unsigned int temp;
1125
1126 /* Reset the LAN911x */
1127 smsc911x_reg_write(pdata, HW_CFG, HW_CFG_SRST_);
1128 timeout = 10;
1129 do {
1130 udelay(10);
1131 temp = smsc911x_reg_read(pdata, HW_CFG);
1132 } while ((--timeout) && (temp & HW_CFG_SRST_));
1133
1134 if (unlikely(temp & HW_CFG_SRST_)) {
1135 SMSC_WARNING(DRV, "Failed to complete reset");
1136 return -EIO;
1137 }
1138 return 0;
1139}
1140
1141/* Sets the device MAC address to dev_addr, called with mac_lock held */
1142static void
1143smsc911x_set_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6])
1144{
1145 u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4];
1146 u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
1147 (dev_addr[1] << 8) | dev_addr[0];
1148
1149 SMSC_ASSERT_MAC_LOCK(pdata);
1150
1151 smsc911x_mac_write(pdata, ADDRH, mac_high16);
1152 smsc911x_mac_write(pdata, ADDRL, mac_low32);
1153}
1154
1155static int smsc911x_open(struct net_device *dev)
1156{
1157 struct smsc911x_data *pdata = netdev_priv(dev);
1158 unsigned int timeout;
1159 unsigned int temp;
1160 unsigned int intcfg;
1161
1162 /* if the phy is not yet registered, retry later*/
1163 if (!pdata->phy_dev) {
1164 SMSC_WARNING(HW, "phy_dev is NULL");
1165 return -EAGAIN;
1166 }
1167
1168 if (!is_valid_ether_addr(dev->dev_addr)) {
1169 SMSC_WARNING(HW, "dev_addr is not a valid MAC address");
1170 return -EADDRNOTAVAIL;
1171 }
1172
1173 /* Reset the LAN911x */
1174 if (smsc911x_soft_reset(pdata)) {
1175 SMSC_WARNING(HW, "soft reset failed");
1176 return -EIO;
1177 }
1178
1179 smsc911x_reg_write(pdata, HW_CFG, 0x00050000);
1180 smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740);
1181
1182 /* Make sure EEPROM has finished loading before setting GPIO_CFG */
1183 timeout = 50;
1184 while ((timeout--) &&
1185 (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_)) {
1186 udelay(10);
1187 }
1188
1189 if (unlikely(timeout == 0))
1190 SMSC_WARNING(IFUP,
1191 "Timed out waiting for EEPROM busy bit to clear");
1192
1193 smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000);
1194
1195 /* The soft reset above cleared the device's MAC address,
1196 * restore it from local copy (set in probe) */
1197 spin_lock_irq(&pdata->mac_lock);
1198 smsc911x_set_mac_address(pdata, dev->dev_addr);
1199 spin_unlock_irq(&pdata->mac_lock);
1200
1201 /* Initialise irqs, but leave all sources disabled */
1202 smsc911x_reg_write(pdata, INT_EN, 0);
1203 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF);
1204
1205 /* Set interrupt deassertion to 100uS */
1206 intcfg = ((10 << 24) | INT_CFG_IRQ_EN_);
1207
1208 if (pdata->irq_polarity) {
1209 SMSC_TRACE(IFUP, "irq polarity: active high");
1210 intcfg |= INT_CFG_IRQ_POL_;
1211 } else {
1212 SMSC_TRACE(IFUP, "irq polarity: active low");
1213 }
1214
1215 if (pdata->irq_type) {
1216 SMSC_TRACE(IFUP, "irq type: push-pull");
1217 intcfg |= INT_CFG_IRQ_TYPE_;
1218 } else {
1219 SMSC_TRACE(IFUP, "irq type: open drain");
1220 }
1221
1222 smsc911x_reg_write(pdata, INT_CFG, intcfg);
1223
1224 SMSC_TRACE(IFUP, "Testing irq handler using IRQ %d", dev->irq);
1225 pdata->software_irq_signal = 0;
1226 smp_wmb();
1227
1228 temp = smsc911x_reg_read(pdata, INT_EN);
1229 temp |= INT_EN_SW_INT_EN_;
1230 smsc911x_reg_write(pdata, INT_EN, temp);
1231
1232 timeout = 1000;
1233 while (timeout--) {
1234 if (pdata->software_irq_signal)
1235 break;
1236 msleep(1);
1237 }
1238
1239 if (!pdata->software_irq_signal) {
1240 dev_warn(&dev->dev, "ISR failed signaling test (IRQ %d)\n",
1241 dev->irq);
1242 return -ENODEV;
1243 }
1244 SMSC_TRACE(IFUP, "IRQ handler passed test using IRQ %d", dev->irq);
1245
1246 dev_info(&dev->dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n",
1247 (unsigned long)pdata->ioaddr, dev->irq);
1248
1249 /* Bring the PHY up */
1250 phy_start(pdata->phy_dev);
1251
1252 temp = smsc911x_reg_read(pdata, HW_CFG);
1253 /* Preserve TX FIFO size and external PHY configuration */
1254 temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF);
1255 temp |= HW_CFG_SF_;
1256 smsc911x_reg_write(pdata, HW_CFG, temp);
1257
1258 temp = smsc911x_reg_read(pdata, FIFO_INT);
1259 temp |= FIFO_INT_TX_AVAIL_LEVEL_;
1260 temp &= ~(FIFO_INT_RX_STS_LEVEL_);
1261 smsc911x_reg_write(pdata, FIFO_INT, temp);
1262
1263 /* set RX Data offset to 2 bytes for alignment */
1264 smsc911x_reg_write(pdata, RX_CFG, (2 << 8));
1265
1266 /* enable NAPI polling before enabling RX interrupts */
1267 napi_enable(&pdata->napi);
1268
1269 temp = smsc911x_reg_read(pdata, INT_EN);
1270 temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_);
1271 smsc911x_reg_write(pdata, INT_EN, temp);
1272
1273 spin_lock_irq(&pdata->mac_lock);
1274 temp = smsc911x_mac_read(pdata, MAC_CR);
1275 temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_);
1276 smsc911x_mac_write(pdata, MAC_CR, temp);
1277 spin_unlock_irq(&pdata->mac_lock);
1278
1279 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_);
1280
1281 netif_start_queue(dev);
1282 return 0;
1283}
1284
1285/* Entry point for stopping the interface */
1286static int smsc911x_stop(struct net_device *dev)
1287{
1288 struct smsc911x_data *pdata = netdev_priv(dev);
1289 unsigned int temp;
1290
1291 BUG_ON(!pdata->phy_dev);
1292
1293 /* Disable all device interrupts */
1294 temp = smsc911x_reg_read(pdata, INT_CFG);
1295 temp &= ~INT_CFG_IRQ_EN_;
1296 smsc911x_reg_write(pdata, INT_CFG, temp);
1297
1298 /* Stop Tx and Rx polling */
1299 netif_stop_queue(dev);
1300 napi_disable(&pdata->napi);
1301
1302 /* At this point all Rx and Tx activity is stopped */
1303 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP);
1304 smsc911x_tx_update_txcounters(dev);
1305
1306 /* Bring the PHY down */
1307 phy_stop(pdata->phy_dev);
1308
1309 SMSC_TRACE(IFDOWN, "Interface stopped");
1310 return 0;
1311}
1312
1313/* Entry point for transmitting a packet */
1314static int smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
1315{
1316 struct smsc911x_data *pdata = netdev_priv(dev);
1317 unsigned int freespace;
1318 unsigned int tx_cmd_a;
1319 unsigned int tx_cmd_b;
1320 unsigned int temp;
1321 u32 wrsz;
1322 ulong bufp;
1323
1324 freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_;
1325
1326 if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD))
1327 SMSC_WARNING(TX_ERR,
1328 "Tx data fifo low, space available: %d", freespace);
1329
1330 /* Word alignment adjustment */
1331 tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16;
1332 tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_;
1333 tx_cmd_a |= (unsigned int)skb->len;
1334
1335 tx_cmd_b = ((unsigned int)skb->len) << 16;
1336 tx_cmd_b |= (unsigned int)skb->len;
1337
1338 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a);
1339 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b);
1340
1341 bufp = (ulong)skb->data & (~0x3);
1342 wrsz = (u32)skb->len + 3;
1343 wrsz += (u32)((ulong)skb->data & 0x3);
1344 wrsz >>= 2;
1345
1346 smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz);
1347 freespace -= (skb->len + 32);
1348 dev_kfree_skb(skb);
1349 dev->trans_start = jiffies;
1350
1351 if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30))
1352 smsc911x_tx_update_txcounters(dev);
1353
1354 if (freespace < TX_FIFO_LOW_THRESHOLD) {
1355 netif_stop_queue(dev);
1356 temp = smsc911x_reg_read(pdata, FIFO_INT);
1357 temp &= 0x00FFFFFF;
1358 temp |= 0x32000000;
1359 smsc911x_reg_write(pdata, FIFO_INT, temp);
1360 }
1361
1362 return NETDEV_TX_OK;
1363}
1364
1365/* Entry point for getting status counters */
1366static struct net_device_stats *smsc911x_get_stats(struct net_device *dev)
1367{
1368 struct smsc911x_data *pdata = netdev_priv(dev);
1369 smsc911x_tx_update_txcounters(dev);
1370 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP);
1371 return &dev->stats;
1372}
1373
1374/* Entry point for setting addressing modes */
1375static void smsc911x_set_multicast_list(struct net_device *dev)
1376{
1377 struct smsc911x_data *pdata = netdev_priv(dev);
1378 unsigned long flags;
1379
1380 if (dev->flags & IFF_PROMISC) {
1381 /* Enabling promiscuous mode */
1382 pdata->set_bits_mask = MAC_CR_PRMS_;
1383 pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
1384 pdata->hashhi = 0;
1385 pdata->hashlo = 0;
1386 } else if (dev->flags & IFF_ALLMULTI) {
1387 /* Enabling all multicast mode */
1388 pdata->set_bits_mask = MAC_CR_MCPAS_;
1389 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_);
1390 pdata->hashhi = 0;
1391 pdata->hashlo = 0;
1392 } else if (dev->mc_count > 0) {
1393 /* Enabling specific multicast addresses */
1394 unsigned int hash_high = 0;
1395 unsigned int hash_low = 0;
1396 unsigned int count = 0;
1397 struct dev_mc_list *mc_list = dev->mc_list;
1398
1399 pdata->set_bits_mask = MAC_CR_HPFILT_;
1400 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_);
1401
1402 while (mc_list) {
1403 count++;
1404 if ((mc_list->dmi_addrlen) == ETH_ALEN) {
1405 unsigned int bitnum =
1406 smsc911x_hash(mc_list->dmi_addr);
1407 unsigned int mask = 0x01 << (bitnum & 0x1F);
1408 if (bitnum & 0x20)
1409 hash_high |= mask;
1410 else
1411 hash_low |= mask;
1412 } else {
1413 SMSC_WARNING(DRV, "dmi_addrlen != 6");
1414 }
1415 mc_list = mc_list->next;
1416 }
1417 if (count != (unsigned int)dev->mc_count)
1418 SMSC_WARNING(DRV, "mc_count != dev->mc_count");
1419
1420 pdata->hashhi = hash_high;
1421 pdata->hashlo = hash_low;
1422 } else {
1423 /* Enabling local MAC address only */
1424 pdata->set_bits_mask = 0;
1425 pdata->clear_bits_mask =
1426 (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
1427 pdata->hashhi = 0;
1428 pdata->hashlo = 0;
1429 }
1430
1431 spin_lock_irqsave(&pdata->mac_lock, flags);
1432
1433 if (pdata->generation <= 1) {
1434 /* Older hardware revision - cannot change these flags while
1435 * receiving data */
1436 if (!pdata->multicast_update_pending) {
1437 unsigned int temp;
1438 SMSC_TRACE(HW, "scheduling mcast update");
1439 pdata->multicast_update_pending = 1;
1440
1441 /* Request the hardware to stop, then perform the
1442 * update when we get an RX_STOP interrupt */
1443 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_);
1444 temp = smsc911x_reg_read(pdata, INT_EN);
1445 temp |= INT_EN_RXSTOP_INT_EN_;
1446 smsc911x_reg_write(pdata, INT_EN, temp);
1447
1448 temp = smsc911x_mac_read(pdata, MAC_CR);
1449 temp &= ~(MAC_CR_RXEN_);
1450 smsc911x_mac_write(pdata, MAC_CR, temp);
1451 } else {
1452 /* There is another update pending, this should now
1453 * use the newer values */
1454 }
1455 } else {
1456 /* Newer hardware revision - can write immediately */
1457 smsc911x_rx_multicast_update(pdata);
1458 }
1459
1460 spin_unlock_irqrestore(&pdata->mac_lock, flags);
1461}
1462
1463static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id)
1464{
1465 struct net_device *dev = dev_id;
1466 struct smsc911x_data *pdata = netdev_priv(dev);
1467 u32 intsts = smsc911x_reg_read(pdata, INT_STS);
1468 u32 inten = smsc911x_reg_read(pdata, INT_EN);
1469 int serviced = IRQ_NONE;
1470 u32 temp;
1471
1472 if (unlikely(intsts & inten & INT_STS_SW_INT_)) {
1473 temp = smsc911x_reg_read(pdata, INT_EN);
1474 temp &= (~INT_EN_SW_INT_EN_);
1475 smsc911x_reg_write(pdata, INT_EN, temp);
1476 smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_);
1477 pdata->software_irq_signal = 1;
1478 smp_wmb();
1479 serviced = IRQ_HANDLED;
1480 }
1481
1482 if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) {
1483 /* Called when there is a multicast update scheduled and
1484 * it is now safe to complete the update */
1485 SMSC_TRACE(INTR, "RX Stop interrupt");
1486 temp = smsc911x_reg_read(pdata, INT_EN);
1487 temp &= (~INT_EN_RXSTOP_INT_EN_);
1488 smsc911x_reg_write(pdata, INT_EN, temp);
1489 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_);
1490 smsc911x_rx_multicast_update_workaround(pdata);
1491 serviced = IRQ_HANDLED;
1492 }
1493
1494 if (intsts & inten & INT_STS_TDFA_) {
1495 temp = smsc911x_reg_read(pdata, FIFO_INT);
1496 temp |= FIFO_INT_TX_AVAIL_LEVEL_;
1497 smsc911x_reg_write(pdata, FIFO_INT, temp);
1498 smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_);
1499 netif_wake_queue(dev);
1500 serviced = IRQ_HANDLED;
1501 }
1502
1503 if (unlikely(intsts & inten & INT_STS_RXE_)) {
1504 SMSC_TRACE(INTR, "RX Error interrupt");
1505 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_);
1506 serviced = IRQ_HANDLED;
1507 }
1508
1509 if (likely(intsts & inten & INT_STS_RSFL_)) {
1510 if (likely(netif_rx_schedule_prep(dev, &pdata->napi))) {
1511 /* Disable Rx interrupts */
1512 temp = smsc911x_reg_read(pdata, INT_EN);
1513 temp &= (~INT_EN_RSFL_EN_);
1514 smsc911x_reg_write(pdata, INT_EN, temp);
1515 /* Schedule a NAPI poll */
1516 __netif_rx_schedule(dev, &pdata->napi);
1517 } else {
1518 SMSC_WARNING(RX_ERR,
1519 "netif_rx_schedule_prep failed");
1520 }
1521 serviced = IRQ_HANDLED;
1522 }
1523
1524 return serviced;
1525}
1526
1527#ifdef CONFIG_NET_POLL_CONTROLLER
1528void smsc911x_poll_controller(struct net_device *dev)
1529{
1530 disable_irq(dev->irq);
1531 smsc911x_irqhandler(0, dev);
1532 enable_irq(dev->irq);
1533}
1534#endif /* CONFIG_NET_POLL_CONTROLLER */
1535
1536/* Standard ioctls for mii-tool */
1537static int smsc911x_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1538{
1539 struct smsc911x_data *pdata = netdev_priv(dev);
1540
1541 if (!netif_running(dev) || !pdata->phy_dev)
1542 return -EINVAL;
1543
1544 return phy_mii_ioctl(pdata->phy_dev, if_mii(ifr), cmd);
1545}
1546
1547static int
1548smsc911x_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd)
1549{
1550 struct smsc911x_data *pdata = netdev_priv(dev);
1551
1552 cmd->maxtxpkt = 1;
1553 cmd->maxrxpkt = 1;
1554 return phy_ethtool_gset(pdata->phy_dev, cmd);
1555}
1556
1557static int
1558smsc911x_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd)
1559{
1560 struct smsc911x_data *pdata = netdev_priv(dev);
1561
1562 return phy_ethtool_sset(pdata->phy_dev, cmd);
1563}
1564
1565static void smsc911x_ethtool_getdrvinfo(struct net_device *dev,
1566 struct ethtool_drvinfo *info)
1567{
1568 strlcpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver));
1569 strlcpy(info->version, SMSC_DRV_VERSION, sizeof(info->version));
1570 strlcpy(info->bus_info, dev->dev.parent->bus_id,
1571 sizeof(info->bus_info));
1572}
1573
1574static int smsc911x_ethtool_nwayreset(struct net_device *dev)
1575{
1576 struct smsc911x_data *pdata = netdev_priv(dev);
1577
1578 return phy_start_aneg(pdata->phy_dev);
1579}
1580
1581static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev)
1582{
1583 struct smsc911x_data *pdata = netdev_priv(dev);
1584 return pdata->msg_enable;
1585}
1586
1587static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level)
1588{
1589 struct smsc911x_data *pdata = netdev_priv(dev);
1590 pdata->msg_enable = level;
1591}
1592
1593static int smsc911x_ethtool_getregslen(struct net_device *dev)
1594{
1595 return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) *
1596 sizeof(u32);
1597}
1598
1599static void
1600smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs,
1601 void *buf)
1602{
1603 struct smsc911x_data *pdata = netdev_priv(dev);
1604 struct phy_device *phy_dev = pdata->phy_dev;
1605 unsigned long flags;
1606 unsigned int i;
1607 unsigned int j = 0;
1608 u32 *data = buf;
1609
1610 regs->version = pdata->idrev;
1611 for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32)))
1612 data[j++] = smsc911x_reg_read(pdata, i);
1613
1614 for (i = MAC_CR; i <= WUCSR; i++) {
1615 spin_lock_irqsave(&pdata->mac_lock, flags);
1616 data[j++] = smsc911x_mac_read(pdata, i);
1617 spin_unlock_irqrestore(&pdata->mac_lock, flags);
1618 }
1619
1620 for (i = 0; i <= 31; i++)
1621 data[j++] = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, i);
1622}
1623
1624static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata)
1625{
1626 unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG);
1627 temp &= ~GPIO_CFG_EEPR_EN_;
1628 smsc911x_reg_write(pdata, GPIO_CFG, temp);
1629 msleep(1);
1630}
1631
1632static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op)
1633{
1634 int timeout = 100;
1635 u32 e2cmd;
1636
1637 SMSC_TRACE(DRV, "op 0x%08x", op);
1638 if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) {
1639 SMSC_WARNING(DRV, "Busy at start");
1640 return -EBUSY;
1641 }
1642
1643 e2cmd = op | E2P_CMD_EPC_BUSY_;
1644 smsc911x_reg_write(pdata, E2P_CMD, e2cmd);
1645
1646 do {
1647 msleep(1);
1648 e2cmd = smsc911x_reg_read(pdata, E2P_CMD);
1649 } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (timeout--));
1650
1651 if (!timeout) {
1652 SMSC_TRACE(DRV, "TIMED OUT");
1653 return -EAGAIN;
1654 }
1655
1656 if (e2cmd & E2P_CMD_EPC_TIMEOUT_) {
1657 SMSC_TRACE(DRV, "Error occured during eeprom operation");
1658 return -EINVAL;
1659 }
1660
1661 return 0;
1662}
1663
1664static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata,
1665 u8 address, u8 *data)
1666{
1667 u32 op = E2P_CMD_EPC_CMD_READ_ | address;
1668 int ret;
1669
1670 SMSC_TRACE(DRV, "address 0x%x", address);
1671 ret = smsc911x_eeprom_send_cmd(pdata, op);
1672
1673 if (!ret)
1674 data[address] = smsc911x_reg_read(pdata, E2P_DATA);
1675
1676 return ret;
1677}
1678
1679static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata,
1680 u8 address, u8 data)
1681{
1682 u32 op = E2P_CMD_EPC_CMD_ERASE_ | address;
1683 int ret;
1684
1685 SMSC_TRACE(DRV, "address 0x%x, data 0x%x", address, data);
1686 ret = smsc911x_eeprom_send_cmd(pdata, op);
1687
1688 if (!ret) {
1689 op = E2P_CMD_EPC_CMD_WRITE_ | address;
1690 smsc911x_reg_write(pdata, E2P_DATA, (u32)data);
1691 ret = smsc911x_eeprom_send_cmd(pdata, op);
1692 }
1693
1694 return ret;
1695}
1696
1697static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev)
1698{
1699 return SMSC911X_EEPROM_SIZE;
1700}
1701
1702static int smsc911x_ethtool_get_eeprom(struct net_device *dev,
1703 struct ethtool_eeprom *eeprom, u8 *data)
1704{
1705 struct smsc911x_data *pdata = netdev_priv(dev);
1706 u8 eeprom_data[SMSC911X_EEPROM_SIZE];
1707 int len;
1708 int i;
1709
1710 smsc911x_eeprom_enable_access(pdata);
1711
1712 len = min(eeprom->len, SMSC911X_EEPROM_SIZE);
1713 for (i = 0; i < len; i++) {
1714 int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data);
1715 if (ret < 0) {
1716 eeprom->len = 0;
1717 return ret;
1718 }
1719 }
1720
1721 memcpy(data, &eeprom_data[eeprom->offset], len);
1722 eeprom->len = len;
1723 return 0;
1724}
1725
1726static int smsc911x_ethtool_set_eeprom(struct net_device *dev,
1727 struct ethtool_eeprom *eeprom, u8 *data)
1728{
1729 int ret;
1730 struct smsc911x_data *pdata = netdev_priv(dev);
1731
1732 smsc911x_eeprom_enable_access(pdata);
1733 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_);
1734 ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data);
1735 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_);
1736
1737 /* Single byte write, according to man page */
1738 eeprom->len = 1;
1739
1740 return ret;
1741}
1742
1743static struct ethtool_ops smsc911x_ethtool_ops = {
1744 .get_settings = smsc911x_ethtool_getsettings,
1745 .set_settings = smsc911x_ethtool_setsettings,
1746 .get_link = ethtool_op_get_link,
1747 .get_drvinfo = smsc911x_ethtool_getdrvinfo,
1748 .nway_reset = smsc911x_ethtool_nwayreset,
1749 .get_msglevel = smsc911x_ethtool_getmsglevel,
1750 .set_msglevel = smsc911x_ethtool_setmsglevel,
1751 .get_regs_len = smsc911x_ethtool_getregslen,
1752 .get_regs = smsc911x_ethtool_getregs,
1753 .get_eeprom_len = smsc911x_ethtool_get_eeprom_len,
1754 .get_eeprom = smsc911x_ethtool_get_eeprom,
1755 .set_eeprom = smsc911x_ethtool_set_eeprom,
1756};
1757
1758/* Initializing private device structures, only called from probe */
1759static int __devinit smsc911x_init(struct net_device *dev)
1760{
1761 struct smsc911x_data *pdata = netdev_priv(dev);
1762 unsigned int byte_test;
1763
1764 SMSC_TRACE(PROBE, "Driver Parameters:");
1765 SMSC_TRACE(PROBE, "LAN base: 0x%08lX",
1766 (unsigned long)pdata->ioaddr);
1767 SMSC_TRACE(PROBE, "IRQ: %d", dev->irq);
1768 SMSC_TRACE(PROBE, "PHY will be autodetected.");
1769
1770#if (!SMSC_CAN_USE_32BIT)
1771 spin_lock_init(&pdata->dev_lock);
1772#endif
1773
1774 if (pdata->ioaddr == 0) {
1775 SMSC_WARNING(PROBE, "pdata->ioaddr: 0x00000000");
1776 return -ENODEV;
1777 }
1778
1779 /* Check byte ordering */
1780 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
1781 SMSC_TRACE(PROBE, "BYTE_TEST: 0x%08X", byte_test);
1782 if (byte_test == 0x43218765) {
1783 SMSC_TRACE(PROBE, "BYTE_TEST looks swapped, "
1784 "applying WORD_SWAP");
1785 smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff);
1786
1787 /* 1 dummy read of BYTE_TEST is needed after a write to
1788 * WORD_SWAP before its contents are valid */
1789 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
1790
1791 byte_test = smsc911x_reg_read(pdata, BYTE_TEST);
1792 }
1793
1794 if (byte_test != 0x87654321) {
1795 SMSC_WARNING(DRV, "BYTE_TEST: 0x%08X", byte_test);
1796 if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) {
1797 SMSC_WARNING(PROBE,
1798 "top 16 bits equal to bottom 16 bits");
1799 SMSC_TRACE(PROBE, "This may mean the chip is set "
1800 "for 32 bit while the bus is reading 16 bit");
1801 }
1802 return -ENODEV;
1803 }
1804
1805 /* Default generation to zero (all workarounds apply) */
1806 pdata->generation = 0;
1807
1808 pdata->idrev = smsc911x_reg_read(pdata, ID_REV);
1809 switch (pdata->idrev & 0xFFFF0000) {
1810 case 0x01180000:
1811 case 0x01170000:
1812 case 0x01160000:
1813 case 0x01150000:
1814 /* LAN911[5678] family */
1815 pdata->generation = pdata->idrev & 0x0000FFFF;
1816 break;
1817
1818 case 0x118A0000:
1819 case 0x117A0000:
1820 case 0x116A0000:
1821 case 0x115A0000:
1822 /* LAN921[5678] family */
1823 pdata->generation = 3;
1824 break;
1825
1826 case 0x92100000:
1827 case 0x92110000:
1828 case 0x92200000:
1829 case 0x92210000:
1830 /* LAN9210/LAN9211/LAN9220/LAN9221 */
1831 pdata->generation = 4;
1832 break;
1833
1834 default:
1835 SMSC_WARNING(PROBE, "LAN911x not identified, idrev: 0x%08X",
1836 pdata->idrev);
1837 return -ENODEV;
1838 }
1839
1840 SMSC_TRACE(PROBE, "LAN911x identified, idrev: 0x%08X, generation: %d",
1841 pdata->idrev, pdata->generation);
1842
1843 if (pdata->generation == 0)
1844 SMSC_WARNING(PROBE,
1845 "This driver is not intended for this chip revision");
1846
1847 /* Reset the LAN911x */
1848 if (smsc911x_soft_reset(pdata))
1849 return -ENODEV;
1850
1851 /* Disable all interrupt sources until we bring the device up */
1852 smsc911x_reg_write(pdata, INT_EN, 0);
1853
1854 ether_setup(dev);
1855 dev->open = smsc911x_open;
1856 dev->stop = smsc911x_stop;
1857 dev->hard_start_xmit = smsc911x_hard_start_xmit;
1858 dev->get_stats = smsc911x_get_stats;
1859 dev->set_multicast_list = smsc911x_set_multicast_list;
1860 dev->flags |= IFF_MULTICAST;
1861 dev->do_ioctl = smsc911x_do_ioctl;
1862 netif_napi_add(dev, &pdata->napi, smsc911x_poll, SMSC_NAPI_WEIGHT);
1863 dev->ethtool_ops = &smsc911x_ethtool_ops;
1864
1865#ifdef CONFIG_NET_POLL_CONTROLLER
1866 dev->poll_controller = smsc911x_poll_controller;
1867#endif /* CONFIG_NET_POLL_CONTROLLER */
1868
1869 return 0;
1870}
1871
1872static int __devexit smsc911x_drv_remove(struct platform_device *pdev)
1873{
1874 struct net_device *dev;
1875 struct smsc911x_data *pdata;
1876 struct resource *res;
1877
1878 dev = platform_get_drvdata(pdev);
1879 BUG_ON(!dev);
1880 pdata = netdev_priv(dev);
1881 BUG_ON(!pdata);
1882 BUG_ON(!pdata->ioaddr);
1883 BUG_ON(!pdata->phy_dev);
1884
1885 SMSC_TRACE(IFDOWN, "Stopping driver.");
1886
1887 phy_disconnect(pdata->phy_dev);
1888 pdata->phy_dev = NULL;
1889 mdiobus_unregister(pdata->mii_bus);
1890 mdiobus_free(pdata->mii_bus);
1891
1892 platform_set_drvdata(pdev, NULL);
1893 unregister_netdev(dev);
1894 free_irq(dev->irq, dev);
1895 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1896 "smsc911x-memory");
1897 if (!res)
1898 platform_get_resource(pdev, IORESOURCE_MEM, 0);
1899
1900 release_mem_region(res->start, res->end - res->start);
1901
1902 iounmap(pdata->ioaddr);
1903
1904 free_netdev(dev);
1905
1906 return 0;
1907}
1908
1909static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
1910{
1911 struct net_device *dev;
1912 struct smsc911x_data *pdata;
1913 struct resource *res;
1914 unsigned int intcfg = 0;
1915 int res_size;
1916 int retval;
1917 DECLARE_MAC_BUF(mac);
1918
1919 pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION);
1920
1921 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1922 "smsc911x-memory");
1923 if (!res)
1924 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1925 if (!res) {
1926 pr_warning("%s: Could not allocate resource.\n",
1927 SMSC_CHIPNAME);
1928 retval = -ENODEV;
1929 goto out_0;
1930 }
1931 res_size = res->end - res->start;
1932
1933 if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) {
1934 retval = -EBUSY;
1935 goto out_0;
1936 }
1937
1938 dev = alloc_etherdev(sizeof(struct smsc911x_data));
1939 if (!dev) {
1940 pr_warning("%s: Could not allocate device.\n", SMSC_CHIPNAME);
1941 retval = -ENOMEM;
1942 goto out_release_io_1;
1943 }
1944
1945 SET_NETDEV_DEV(dev, &pdev->dev);
1946
1947 pdata = netdev_priv(dev);
1948
1949 dev->irq = platform_get_irq(pdev, 0);
1950 pdata->ioaddr = ioremap_nocache(res->start, res_size);
1951
1952 /* copy config parameters across if present, otherwise pdata
1953 * defaults to zeros */
1954 if (pdev->dev.platform_data) {
1955 struct smsc911x_platform_config *config =
1956 pdev->dev.platform_data;
1957 pdata->irq_polarity = config->irq_polarity;
1958 pdata->irq_type = config->irq_type;
1959 pdata->phy_interface = config->phy_interface;
1960 }
1961
1962 pdata->dev = dev;
1963 pdata->msg_enable = ((1 << debug) - 1);
1964
1965 if (pdata->ioaddr == NULL) {
1966 SMSC_WARNING(PROBE,
1967 "Error smsc911x base address invalid");
1968 retval = -ENOMEM;
1969 goto out_free_netdev_2;
1970 }
1971
1972 retval = smsc911x_init(dev);
1973 if (retval < 0)
1974 goto out_unmap_io_3;
1975
1976 /* configure irq polarity and type before connecting isr */
1977 if (pdata->irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
1978 intcfg |= INT_CFG_IRQ_POL_;
1979
1980 if (pdata->irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
1981 intcfg |= INT_CFG_IRQ_TYPE_;
1982
1983 smsc911x_reg_write(pdata, INT_CFG, intcfg);
1984
1985 /* Ensure interrupts are globally disabled before connecting ISR */
1986 smsc911x_reg_write(pdata, INT_EN, 0);
1987 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF);
1988
1989 retval = request_irq(dev->irq, smsc911x_irqhandler, IRQF_DISABLED,
1990 SMSC_CHIPNAME, dev);
1991 if (retval) {
1992 SMSC_WARNING(PROBE,
1993 "Unable to claim requested irq: %d", dev->irq);
1994 goto out_unmap_io_3;
1995 }
1996
1997 platform_set_drvdata(pdev, dev);
1998
1999 retval = register_netdev(dev);
2000 if (retval) {
2001 SMSC_WARNING(PROBE,
2002 "Error %i registering device", retval);
2003 goto out_unset_drvdata_4;
2004 } else {
2005 SMSC_TRACE(PROBE, "Network interface: \"%s\"", dev->name);
2006 }
2007
2008 spin_lock_init(&pdata->mac_lock);
2009
2010 retval = smsc911x_mii_init(pdev, dev);
2011 if (retval) {
2012 SMSC_WARNING(PROBE,
2013 "Error %i initialising mii", retval);
2014 goto out_unregister_netdev_5;
2015 }
2016
2017 spin_lock_irq(&pdata->mac_lock);
2018
2019 /* Check if mac address has been specified when bringing interface up */
2020 if (is_valid_ether_addr(dev->dev_addr)) {
2021 smsc911x_set_mac_address(pdata, dev->dev_addr);
2022 SMSC_TRACE(PROBE, "MAC Address is specified by configuration");
2023 } else {
2024 /* Try reading mac address from device. if EEPROM is present
2025 * it will already have been set */
2026 u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH);
2027 u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL);
2028 dev->dev_addr[0] = (u8)(mac_low32);
2029 dev->dev_addr[1] = (u8)(mac_low32 >> 8);
2030 dev->dev_addr[2] = (u8)(mac_low32 >> 16);
2031 dev->dev_addr[3] = (u8)(mac_low32 >> 24);
2032 dev->dev_addr[4] = (u8)(mac_high16);
2033 dev->dev_addr[5] = (u8)(mac_high16 >> 8);
2034
2035 if (is_valid_ether_addr(dev->dev_addr)) {
2036 /* eeprom values are valid so use them */
2037 SMSC_TRACE(PROBE,
2038 "Mac Address is read from LAN911x EEPROM");
2039 } else {
2040 /* eeprom values are invalid, generate random MAC */
2041 random_ether_addr(dev->dev_addr);
2042 smsc911x_set_mac_address(pdata, dev->dev_addr);
2043 SMSC_TRACE(PROBE,
2044 "MAC Address is set to random_ether_addr");
2045 }
2046 }
2047
2048 spin_unlock_irq(&pdata->mac_lock);
2049
2050 dev_info(&dev->dev, "MAC Address: %s\n",
2051 print_mac(mac, dev->dev_addr));
2052
2053 return 0;
2054
2055out_unregister_netdev_5:
2056 unregister_netdev(dev);
2057out_unset_drvdata_4:
2058 platform_set_drvdata(pdev, NULL);
2059 free_irq(dev->irq, dev);
2060out_unmap_io_3:
2061 iounmap(pdata->ioaddr);
2062out_free_netdev_2:
2063 free_netdev(dev);
2064out_release_io_1:
2065 release_mem_region(res->start, res->end - res->start);
2066out_0:
2067 return retval;
2068}
2069
2070static struct platform_driver smsc911x_driver = {
2071 .probe = smsc911x_drv_probe,
2072 .remove = smsc911x_drv_remove,
2073 .driver = {
2074 .name = SMSC_CHIPNAME,
2075 },
2076};
2077
2078/* Entry point for loading the module */
2079static int __init smsc911x_init_module(void)
2080{
2081 return platform_driver_register(&smsc911x_driver);
2082}
2083
2084/* entry point for unloading the module */
2085static void __exit smsc911x_cleanup_module(void)
2086{
2087 platform_driver_unregister(&smsc911x_driver);
2088}
2089
2090module_init(smsc911x_init_module);
2091module_exit(smsc911x_cleanup_module);
diff --git a/drivers/net/smsc911x.h b/drivers/net/smsc911x.h
new file mode 100644
index 000000000000..feb36de274ca
--- /dev/null
+++ b/drivers/net/smsc911x.h
@@ -0,0 +1,394 @@
1/***************************************************************************
2 *
3 * Copyright (C) 2004-2008 SMSC
4 * Copyright (C) 2005-2008 ARM
5 *
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License
8 * as published by the Free Software Foundation; either version 2
9 * of the License, or (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
19 *
20 ***************************************************************************/
21#ifndef __SMSC911X_H__
22#define __SMSC911X_H__
23
24#define SMSC_CAN_USE_32BIT 1
25#define TX_FIFO_LOW_THRESHOLD ((u32)1600)
26#define SMSC911X_EEPROM_SIZE ((u32)7)
27#define USE_DEBUG 0
28
29/* This is the maximum number of packets to be received every
30 * NAPI poll */
31#define SMSC_NAPI_WEIGHT 16
32
33/* implements a PHY loopback test at initialisation time, to ensure a packet
34 * can be succesfully looped back */
35#define USE_PHY_WORK_AROUND
36
37#define DPRINTK(nlevel, klevel, fmt, args...) \
38 ((void)((NETIF_MSG_##nlevel & pdata->msg_enable) && \
39 printk(KERN_##klevel "%s: %s: " fmt "\n", \
40 pdata->dev->name, __func__, ## args)))
41
42#if USE_DEBUG >= 1
43#define SMSC_WARNING(nlevel, fmt, args...) \
44 DPRINTK(nlevel, WARNING, fmt, ## args)
45#else
46#define SMSC_WARNING(nlevel, fmt, args...) \
47 ({ do {} while (0); 0; })
48#endif
49
50#if USE_DEBUG >= 2
51#define SMSC_TRACE(nlevel, fmt, args...) \
52 DPRINTK(nlevel, INFO, fmt, ## args)
53#else
54#define SMSC_TRACE(nlevel, fmt, args...) \
55 ({ do {} while (0); 0; })
56#endif
57
58#ifdef CONFIG_DEBUG_SPINLOCK
59#define SMSC_ASSERT_MAC_LOCK(pdata) \
60 WARN_ON(!spin_is_locked(&pdata->mac_lock))
61#else
62#define SMSC_ASSERT_MAC_LOCK(pdata) do {} while (0)
63#endif /* CONFIG_DEBUG_SPINLOCK */
64
65#define FLOW_CTRL_TX (1)
66#define FLOW_CTRL_RX (2)
67
68/* SMSC911x registers and bitfields */
69#define RX_DATA_FIFO 0x00
70
71#define TX_DATA_FIFO 0x20
72#define TX_CMD_A_ON_COMP_ 0x80000000
73#define TX_CMD_A_BUF_END_ALGN_ 0x03000000
74#define TX_CMD_A_4_BYTE_ALGN_ 0x00000000
75#define TX_CMD_A_16_BYTE_ALGN_ 0x01000000
76#define TX_CMD_A_32_BYTE_ALGN_ 0x02000000
77#define TX_CMD_A_DATA_OFFSET_ 0x001F0000
78#define TX_CMD_A_FIRST_SEG_ 0x00002000
79#define TX_CMD_A_LAST_SEG_ 0x00001000
80#define TX_CMD_A_BUF_SIZE_ 0x000007FF
81#define TX_CMD_B_PKT_TAG_ 0xFFFF0000
82#define TX_CMD_B_ADD_CRC_DISABLE_ 0x00002000
83#define TX_CMD_B_DISABLE_PADDING_ 0x00001000
84#define TX_CMD_B_PKT_BYTE_LENGTH_ 0x000007FF
85
86#define RX_STATUS_FIFO 0x40
87#define RX_STS_ES_ 0x00008000
88#define RX_STS_MCAST_ 0x00000400
89
90#define RX_STATUS_FIFO_PEEK 0x44
91
92#define TX_STATUS_FIFO 0x48
93#define TX_STS_ES_ 0x00008000
94
95#define TX_STATUS_FIFO_PEEK 0x4C
96
97#define ID_REV 0x50
98#define ID_REV_CHIP_ID_ 0xFFFF0000
99#define ID_REV_REV_ID_ 0x0000FFFF
100
101#define INT_CFG 0x54
102#define INT_CFG_INT_DEAS_ 0xFF000000
103#define INT_CFG_INT_DEAS_CLR_ 0x00004000
104#define INT_CFG_INT_DEAS_STS_ 0x00002000
105#define INT_CFG_IRQ_INT_ 0x00001000
106#define INT_CFG_IRQ_EN_ 0x00000100
107#define INT_CFG_IRQ_POL_ 0x00000010
108#define INT_CFG_IRQ_TYPE_ 0x00000001
109
110#define INT_STS 0x58
111#define INT_STS_SW_INT_ 0x80000000
112#define INT_STS_TXSTOP_INT_ 0x02000000
113#define INT_STS_RXSTOP_INT_ 0x01000000
114#define INT_STS_RXDFH_INT_ 0x00800000
115#define INT_STS_RXDF_INT_ 0x00400000
116#define INT_STS_TX_IOC_ 0x00200000
117#define INT_STS_RXD_INT_ 0x00100000
118#define INT_STS_GPT_INT_ 0x00080000
119#define INT_STS_PHY_INT_ 0x00040000
120#define INT_STS_PME_INT_ 0x00020000
121#define INT_STS_TXSO_ 0x00010000
122#define INT_STS_RWT_ 0x00008000
123#define INT_STS_RXE_ 0x00004000
124#define INT_STS_TXE_ 0x00002000
125#define INT_STS_TDFU_ 0x00000800
126#define INT_STS_TDFO_ 0x00000400
127#define INT_STS_TDFA_ 0x00000200
128#define INT_STS_TSFF_ 0x00000100
129#define INT_STS_TSFL_ 0x00000080
130#define INT_STS_RXDF_ 0x00000040
131#define INT_STS_RDFL_ 0x00000020
132#define INT_STS_RSFF_ 0x00000010
133#define INT_STS_RSFL_ 0x00000008
134#define INT_STS_GPIO2_INT_ 0x00000004
135#define INT_STS_GPIO1_INT_ 0x00000002
136#define INT_STS_GPIO0_INT_ 0x00000001
137
138#define INT_EN 0x5C
139#define INT_EN_SW_INT_EN_ 0x80000000
140#define INT_EN_TXSTOP_INT_EN_ 0x02000000
141#define INT_EN_RXSTOP_INT_EN_ 0x01000000
142#define INT_EN_RXDFH_INT_EN_ 0x00800000
143#define INT_EN_TIOC_INT_EN_ 0x00200000
144#define INT_EN_RXD_INT_EN_ 0x00100000
145#define INT_EN_GPT_INT_EN_ 0x00080000
146#define INT_EN_PHY_INT_EN_ 0x00040000
147#define INT_EN_PME_INT_EN_ 0x00020000
148#define INT_EN_TXSO_EN_ 0x00010000
149#define INT_EN_RWT_EN_ 0x00008000
150#define INT_EN_RXE_EN_ 0x00004000
151#define INT_EN_TXE_EN_ 0x00002000
152#define INT_EN_TDFU_EN_ 0x00000800
153#define INT_EN_TDFO_EN_ 0x00000400
154#define INT_EN_TDFA_EN_ 0x00000200
155#define INT_EN_TSFF_EN_ 0x00000100
156#define INT_EN_TSFL_EN_ 0x00000080
157#define INT_EN_RXDF_EN_ 0x00000040
158#define INT_EN_RDFL_EN_ 0x00000020
159#define INT_EN_RSFF_EN_ 0x00000010
160#define INT_EN_RSFL_EN_ 0x00000008
161#define INT_EN_GPIO2_INT_ 0x00000004
162#define INT_EN_GPIO1_INT_ 0x00000002
163#define INT_EN_GPIO0_INT_ 0x00000001
164
165#define BYTE_TEST 0x64
166
167#define FIFO_INT 0x68
168#define FIFO_INT_TX_AVAIL_LEVEL_ 0xFF000000
169#define FIFO_INT_TX_STS_LEVEL_ 0x00FF0000
170#define FIFO_INT_RX_AVAIL_LEVEL_ 0x0000FF00
171#define FIFO_INT_RX_STS_LEVEL_ 0x000000FF
172
173#define RX_CFG 0x6C
174#define RX_CFG_RX_END_ALGN_ 0xC0000000
175#define RX_CFG_RX_END_ALGN4_ 0x00000000
176#define RX_CFG_RX_END_ALGN16_ 0x40000000
177#define RX_CFG_RX_END_ALGN32_ 0x80000000
178#define RX_CFG_RX_DMA_CNT_ 0x0FFF0000
179#define RX_CFG_RX_DUMP_ 0x00008000
180#define RX_CFG_RXDOFF_ 0x00001F00
181
182#define TX_CFG 0x70
183#define TX_CFG_TXS_DUMP_ 0x00008000
184#define TX_CFG_TXD_DUMP_ 0x00004000
185#define TX_CFG_TXSAO_ 0x00000004
186#define TX_CFG_TX_ON_ 0x00000002
187#define TX_CFG_STOP_TX_ 0x00000001
188
189#define HW_CFG 0x74
190#define HW_CFG_TTM_ 0x00200000
191#define HW_CFG_SF_ 0x00100000
192#define HW_CFG_TX_FIF_SZ_ 0x000F0000
193#define HW_CFG_TR_ 0x00003000
194#define HW_CFG_SRST_ 0x00000001
195
196/* only available on 115/117 */
197#define HW_CFG_PHY_CLK_SEL_ 0x00000060
198#define HW_CFG_PHY_CLK_SEL_INT_PHY_ 0x00000000
199#define HW_CFG_PHY_CLK_SEL_EXT_PHY_ 0x00000020
200#define HW_CFG_PHY_CLK_SEL_CLK_DIS_ 0x00000040
201#define HW_CFG_SMI_SEL_ 0x00000010
202#define HW_CFG_EXT_PHY_DET_ 0x00000008
203#define HW_CFG_EXT_PHY_EN_ 0x00000004
204#define HW_CFG_SRST_TO_ 0x00000002
205
206/* only available on 116/118 */
207#define HW_CFG_32_16_BIT_MODE_ 0x00000004
208
209#define RX_DP_CTRL 0x78
210#define RX_DP_CTRL_RX_FFWD_ 0x80000000
211
212#define RX_FIFO_INF 0x7C
213#define RX_FIFO_INF_RXSUSED_ 0x00FF0000
214#define RX_FIFO_INF_RXDUSED_ 0x0000FFFF
215
216#define TX_FIFO_INF 0x80
217#define TX_FIFO_INF_TSUSED_ 0x00FF0000
218#define TX_FIFO_INF_TDFREE_ 0x0000FFFF
219
220#define PMT_CTRL 0x84
221#define PMT_CTRL_PM_MODE_ 0x00003000
222#define PMT_CTRL_PM_MODE_D0_ 0x00000000
223#define PMT_CTRL_PM_MODE_D1_ 0x00001000
224#define PMT_CTRL_PM_MODE_D2_ 0x00002000
225#define PMT_CTRL_PM_MODE_D3_ 0x00003000
226#define PMT_CTRL_PHY_RST_ 0x00000400
227#define PMT_CTRL_WOL_EN_ 0x00000200
228#define PMT_CTRL_ED_EN_ 0x00000100
229#define PMT_CTRL_PME_TYPE_ 0x00000040
230#define PMT_CTRL_WUPS_ 0x00000030
231#define PMT_CTRL_WUPS_NOWAKE_ 0x00000000
232#define PMT_CTRL_WUPS_ED_ 0x00000010
233#define PMT_CTRL_WUPS_WOL_ 0x00000020
234#define PMT_CTRL_WUPS_MULTI_ 0x00000030
235#define PMT_CTRL_PME_IND_ 0x00000008
236#define PMT_CTRL_PME_POL_ 0x00000004
237#define PMT_CTRL_PME_EN_ 0x00000002
238#define PMT_CTRL_READY_ 0x00000001
239
240#define GPIO_CFG 0x88
241#define GPIO_CFG_LED3_EN_ 0x40000000
242#define GPIO_CFG_LED2_EN_ 0x20000000
243#define GPIO_CFG_LED1_EN_ 0x10000000
244#define GPIO_CFG_GPIO2_INT_POL_ 0x04000000
245#define GPIO_CFG_GPIO1_INT_POL_ 0x02000000
246#define GPIO_CFG_GPIO0_INT_POL_ 0x01000000
247#define GPIO_CFG_EEPR_EN_ 0x00700000
248#define GPIO_CFG_GPIOBUF2_ 0x00040000
249#define GPIO_CFG_GPIOBUF1_ 0x00020000
250#define GPIO_CFG_GPIOBUF0_ 0x00010000
251#define GPIO_CFG_GPIODIR2_ 0x00000400
252#define GPIO_CFG_GPIODIR1_ 0x00000200
253#define GPIO_CFG_GPIODIR0_ 0x00000100
254#define GPIO_CFG_GPIOD4_ 0x00000020
255#define GPIO_CFG_GPIOD3_ 0x00000010
256#define GPIO_CFG_GPIOD2_ 0x00000004
257#define GPIO_CFG_GPIOD1_ 0x00000002
258#define GPIO_CFG_GPIOD0_ 0x00000001
259
260#define GPT_CFG 0x8C
261#define GPT_CFG_TIMER_EN_ 0x20000000
262#define GPT_CFG_GPT_LOAD_ 0x0000FFFF
263
264#define GPT_CNT 0x90
265#define GPT_CNT_GPT_CNT_ 0x0000FFFF
266
267#define WORD_SWAP 0x98
268
269#define FREE_RUN 0x9C
270
271#define RX_DROP 0xA0
272
273#define MAC_CSR_CMD 0xA4
274#define MAC_CSR_CMD_CSR_BUSY_ 0x80000000
275#define MAC_CSR_CMD_R_NOT_W_ 0x40000000
276#define MAC_CSR_CMD_CSR_ADDR_ 0x000000FF
277
278#define MAC_CSR_DATA 0xA8
279
280#define AFC_CFG 0xAC
281#define AFC_CFG_AFC_HI_ 0x00FF0000
282#define AFC_CFG_AFC_LO_ 0x0000FF00
283#define AFC_CFG_BACK_DUR_ 0x000000F0
284#define AFC_CFG_FCMULT_ 0x00000008
285#define AFC_CFG_FCBRD_ 0x00000004
286#define AFC_CFG_FCADD_ 0x00000002
287#define AFC_CFG_FCANY_ 0x00000001
288
289#define E2P_CMD 0xB0
290#define E2P_CMD_EPC_BUSY_ 0x80000000
291#define E2P_CMD_EPC_CMD_ 0x70000000
292#define E2P_CMD_EPC_CMD_READ_ 0x00000000
293#define E2P_CMD_EPC_CMD_EWDS_ 0x10000000
294#define E2P_CMD_EPC_CMD_EWEN_ 0x20000000
295#define E2P_CMD_EPC_CMD_WRITE_ 0x30000000
296#define E2P_CMD_EPC_CMD_WRAL_ 0x40000000
297#define E2P_CMD_EPC_CMD_ERASE_ 0x50000000
298#define E2P_CMD_EPC_CMD_ERAL_ 0x60000000
299#define E2P_CMD_EPC_CMD_RELOAD_ 0x70000000
300#define E2P_CMD_EPC_TIMEOUT_ 0x00000200
301#define E2P_CMD_MAC_ADDR_LOADED_ 0x00000100
302#define E2P_CMD_EPC_ADDR_ 0x000000FF
303
304#define E2P_DATA 0xB4
305#define E2P_DATA_EEPROM_DATA_ 0x000000FF
306#define LAN_REGISTER_EXTENT 0x00000100
307
308/*
309 * MAC Control and Status Register (Indirect Address)
310 * Offset (through the MAC_CSR CMD and DATA port)
311 */
312#define MAC_CR 0x01
313#define MAC_CR_RXALL_ 0x80000000
314#define MAC_CR_HBDIS_ 0x10000000
315#define MAC_CR_RCVOWN_ 0x00800000
316#define MAC_CR_LOOPBK_ 0x00200000
317#define MAC_CR_FDPX_ 0x00100000
318#define MAC_CR_MCPAS_ 0x00080000
319#define MAC_CR_PRMS_ 0x00040000
320#define MAC_CR_INVFILT_ 0x00020000
321#define MAC_CR_PASSBAD_ 0x00010000
322#define MAC_CR_HFILT_ 0x00008000
323#define MAC_CR_HPFILT_ 0x00002000
324#define MAC_CR_LCOLL_ 0x00001000
325#define MAC_CR_BCAST_ 0x00000800
326#define MAC_CR_DISRTY_ 0x00000400
327#define MAC_CR_PADSTR_ 0x00000100
328#define MAC_CR_BOLMT_MASK_ 0x000000C0
329#define MAC_CR_DFCHK_ 0x00000020
330#define MAC_CR_TXEN_ 0x00000008
331#define MAC_CR_RXEN_ 0x00000004
332
333#define ADDRH 0x02
334
335#define ADDRL 0x03
336
337#define HASHH 0x04
338
339#define HASHL 0x05
340
341#define MII_ACC 0x06
342#define MII_ACC_PHY_ADDR_ 0x0000F800
343#define MII_ACC_MIIRINDA_ 0x000007C0
344#define MII_ACC_MII_WRITE_ 0x00000002
345#define MII_ACC_MII_BUSY_ 0x00000001
346
347#define MII_DATA 0x07
348
349#define FLOW 0x08
350#define FLOW_FCPT_ 0xFFFF0000
351#define FLOW_FCPASS_ 0x00000004
352#define FLOW_FCEN_ 0x00000002
353#define FLOW_FCBSY_ 0x00000001
354
355#define VLAN1 0x09
356
357#define VLAN2 0x0A
358
359#define WUFF 0x0B
360
361#define WUCSR 0x0C
362#define WUCSR_GUE_ 0x00000200
363#define WUCSR_WUFR_ 0x00000040
364#define WUCSR_MPR_ 0x00000020
365#define WUCSR_WAKE_EN_ 0x00000004
366#define WUCSR_MPEN_ 0x00000002
367
368/*
369 * Phy definitions (vendor-specific)
370 */
371#define LAN9118_PHY_ID 0x00C0001C
372
373#define MII_INTSTS 0x1D
374
375#define MII_INTMSK 0x1E
376#define PHY_INTMSK_AN_RCV_ (1 << 1)
377#define PHY_INTMSK_PDFAULT_ (1 << 2)
378#define PHY_INTMSK_AN_ACK_ (1 << 3)
379#define PHY_INTMSK_LNKDOWN_ (1 << 4)
380#define PHY_INTMSK_RFAULT_ (1 << 5)
381#define PHY_INTMSK_AN_COMP_ (1 << 6)
382#define PHY_INTMSK_ENERGYON_ (1 << 7)
383#define PHY_INTMSK_DEFAULT_ (PHY_INTMSK_ENERGYON_ | \
384 PHY_INTMSK_AN_COMP_ | \
385 PHY_INTMSK_RFAULT_ | \
386 PHY_INTMSK_LNKDOWN_)
387
388#define ADVERTISE_PAUSE_ALL (ADVERTISE_PAUSE_CAP | \
389 ADVERTISE_PAUSE_ASYM)
390
391#define LPA_PAUSE_ALL (LPA_PAUSE_CAP | \
392 LPA_PAUSE_ASYM)
393
394#endif /* __SMSC911X_H__ */
diff --git a/include/linux/smsc911x.h b/include/linux/smsc911x.h
new file mode 100644
index 000000000000..47c4ffd10dbb
--- /dev/null
+++ b/include/linux/smsc911x.h
@@ -0,0 +1,42 @@
1/***************************************************************************
2 *
3 * Copyright (C) 2004-2008 SMSC
4 * Copyright (C) 2005-2008 ARM
5 *
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License
8 * as published by the Free Software Foundation; either version 2
9 * of the License, or (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
19 *
20 ***************************************************************************/
21#ifndef __LINUX_SMSC911X_H__
22#define __LINUX_SMSC911X_H__
23
24#include <linux/phy.h>
25
26/* platform_device configuration data, should be assigned to
27 * the platform_device's dev.platform_data */
28struct smsc911x_platform_config {
29 unsigned int irq_polarity;
30 unsigned int irq_type;
31 phy_interface_t phy_interface;
32};
33
34/* Constants for platform_device irq polarity configuration */
35#define SMSC911X_IRQ_POLARITY_ACTIVE_LOW 0
36#define SMSC911X_IRQ_POLARITY_ACTIVE_HIGH 1
37
38/* Constants for platform_device irq type configuration */
39#define SMSC911X_IRQ_TYPE_OPEN_DRAIN 0
40#define SMSC911X_IRQ_TYPE_PUSH_PULL 1
41
42#endif /* __LINUX_SMSC911X_H__ */
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-09 23:44:59 -0500