/*
**********************************************************************
* ecard.c - E-card initialization code
* Copyright 1999, 2000 Creative Labs, Inc.
*
**********************************************************************
*
* Date Author Summary of changes
* ---- ------ ------------------
* October 20, 1999 Bertrand Lee base code release
*
**********************************************************************
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this program; if not, write to the Free
* Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139,
* USA.
*
**********************************************************************
*/
#include "ecard.h"
#include "hwaccess.h"
/* Private routines */
static void ecard_setadcgain(struct emu10k1_card *, struct ecard_state *, u16);
static void ecard_write(struct emu10k1_card *, u32);
/**************************************************************************
* @func Set the gain of the ECARD's CS3310 Trim/gain controller. The
* trim value consists of a 16bit value which is composed of two
* 8 bit gain/trim values, one for the left channel and one for the
* right channel. The following table maps from the Gain/Attenuation
* value in decibels into the corresponding bit pattern for a single
* channel.
*/
static void ecard_setadcgain(struct emu10k1_card *card, struct ecard_state *ecard, u16 gain)
{
u32 currbit;
ecard->adc_gain = gain;
/* Enable writing to the TRIM registers */
ecard_write(card, ecard->control_bits & ~EC_TRIM_CSN);
/* Do it again to insure that we meet hold time requirements */
ecard_write(card, ecard->control_bits & ~EC_TRIM_CSN);
for (currbit = (1L << 15); currbit; currbit >>= 1) {
u32 value = ecard->control_bits & ~(EC_TRIM_CSN|EC_TRIM_SDATA);
if (gain & currbit)
value |= EC_TRIM_SDATA;
/* Clock the bit */
ecard_write(card, value);
ecard_write(card, value | EC_TRIM_SCLK);
ecard_write(card, value);
}
ecard_write(card, ecard->control_bits);
}
/**************************************************************************
* @func Clock bits into the Ecard's control latch. The Ecard uses a
* control latch will is loaded bit-serially by toggling the Modem control
* lines from function 2 on the E8010. This function hides these details
* and presents the illusion that we are actually writing to a distinct
* register.
*/
static void ecard_write(struct emu10k1_card *card, u32 value)
{
u16 count;
u32 data, hcvalue;
unsigned long flags;
spin_lock_irqsave(&card->lock, flags);
hcvalue = inl(card->iobase + HCFG) & ~(HOOKN_BIT|HANDN_BIT|PULSEN_BIT);
outl(card->iobase + HCFG, hcvalue);
for (count = 0 ; count < EC_NUM_CONTROL_BITS; count++) {
/* Set up the value */
data = ((value & 0x1) ? PULSEN_BIT : 0);
value >>= 1;
outl(card->iobase + HCFG, hcvalue | data);
/* Clock the shift register */
outl(card->iobase + HCFG, hcvalue | data | HANDN_BIT);
outl(card->iobase + HCFG, hcvalue | data);
}
/* Latch the bits */
outl(card->iobase + HCFG, hcvalue | HOOKN_BIT);
outl(card->iobase + HCFG, hcvalue);
spin_unlock_irqrestore(&card->lock, flags);
}
void __devinit emu10k1_ecard_init(struct emu10k1_card *card)
{
u32 hcvalue;
struct ecard_state ecard;
/* Set up the initial settings */
ecard.mux0_setting = EC_DEFAULT_SPDIF0_SEL;
ecard.mux1_setting = EC_DEFAULT_SPDIF1_SEL;
ecard.mux2_setting = 0;
ecard.adc_gain = EC_DEFAULT_ADC_GAIN;
ecard.control_bits = EC_RAW_RUN_MODE |
EC_SPDIF0_SELECT(ecard.mux0_setting) |
EC_SPDIF1_SELECT(ecard.mux1_setting);
/* Step 0: Set the codec type in the hardware control register
* and enable audio output */
hcvalue = emu10k1_readfn0(card, HCFG);
emu10k1_writefn0(card, HCFG, hcvalue | HCFG_AUDIOENABLE | HCFG_CODECFORMAT_I2S);
/* Step 1: Turn off the led and deassert TRIM_CS */
ecard_write(card, EC_ADCCAL | EC_LEDN | EC_TRIM_CSN);
/* Step 2: Calibrate the ADC and DAC */
ecard_write(card, EC_DACCAL | EC_LEDN | EC_TRIM_CSN);
/* Step 3: Wait for awhile; FIXME: Is this correct? */
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(HZ);
/* Step 4: Switch off the DAC and ADC calibration. Note
* That ADC_CAL is actually an inverted signal, so we assert
* it here to stop calibration. */
ecard_write(card, EC_ADCCAL | EC_LEDN | EC_TRIM_CSN);
/* Step 4: Switch into run mode */
ecard_write(card, ecard.control_bits);
/* Step 5: Set the analog input gain */
ecard_setadcgain(card, &ecard, ecard.adc_gain);
}
