#ifndef __SOUND_OPL3_H
#define __SOUND_OPL3_H
/*
* Definitions of the OPL-3 registers.
*
* Copyright (c) by Jaroslav Kysela <perex@suse.cz>,
* Hannu Savolainen 1993-1996
*
*
* The OPL-3 mode is switched on by writing 0x01, to the offset 5
* of the right side.
*
* Another special register at the right side is at offset 4. It contains
* a bit mask defining which voices are used as 4 OP voices.
*
* The percussive mode is implemented in the left side only.
*
* With the above exceptions the both sides can be operated independently.
*
* A 4 OP voice can be created by setting the corresponding
* bit at offset 4 of the right side.
*
* For example setting the rightmost bit (0x01) changes the
* first voice on the right side to the 4 OP mode. The fourth
* voice is made inaccessible.
*
* If a voice is set to the 2 OP mode, it works like 2 OP modes
* of the original YM3812 (AdLib). In addition the voice can
* be connected the left, right or both stereo channels. It can
* even be left unconnected. This works with 4 OP voices also.
*
* The stereo connection bits are located in the FEEDBACK_CONNECTION
* register of the voice (0xC0-0xC8). In 4 OP voices these bits are
* in the second half of the voice.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include "driver.h"
#include <linux/time.h>
#include "core.h"
#include "hwdep.h"
#include "timer.h"
#include "seq_midi_emul.h"
#ifdef CONFIG_SND_SEQUENCER_OSS
#include "seq_oss.h"
#include "seq_oss_legacy.h"
#endif
#include "seq_device.h"
#include "ainstr_fm.h"
/*
* Register numbers for the global registers
*/
#define OPL3_REG_TEST 0x01
#define OPL3_ENABLE_WAVE_SELECT 0x20
#define OPL3_REG_TIMER1 0x02
#define OPL3_REG_TIMER2 0x03
#define OPL3_REG_TIMER_CONTROL 0x04 /* Left side */
#define OPL3_IRQ_RESET 0x80
#define OPL3_TIMER1_MASK 0x40
#define OPL3_TIMER2_MASK 0x20
#define OPL3_TIMER1_START 0x01
#define OPL3_TIMER2_START 0x02
#define OPL3_REG_CONNECTION_SELECT 0x04 /* Right side */
#define OPL3_LEFT_4OP_0 0x01
#define OPL3_LEFT_4OP_1 0x02
#define OPL3_LEFT_4OP_2 0x04
#define OPL3_RIGHT_4OP_0 0x08
#define OPL3_RIGHT_4OP_1 0x10
#define OPL3_RIGHT_4OP_2 0x20
#define OPL3_REG_MODE 0x05 /* Right side */
#define OPL3_OPL3_ENABLE 0x01 /* OPL3 mode */
#define OPL3_OPL4_ENABLE 0x02 /* OPL4 mode */
#define OPL3_REG_KBD_SPLIT 0x08 /* Left side */
#define OPL3_COMPOSITE_SINE_WAVE_MODE 0x80 /* Don't use with OPL-3? */
#define OPL3_KEYBOARD_SPLIT 0x40
#define OPL3_REG_PERCUSSION 0xbd /* Left side only */
#define OPL3_TREMOLO_DEPTH 0x80
#define OPL3_VIBRATO_DEPTH 0x40
#define OPL3_PERCUSSION_ENABLE 0x20
#define OPL3_BASSDRUM_ON 0x10
#define OPL3_SNAREDRUM_ON 0x08
#define OPL3_TOMTOM_ON 0x04
#define OPL3_CYMBAL_ON 0x02
#define OPL3_HIHAT_ON 0x01
/*
* Offsets to the register banks for operators. To get the
* register number just add the operator offset to the bank offset
*
* AM/VIB/EG/KSR/Multiple (0x20 to 0x35)
*/
#define OPL3_REG_AM_VIB 0x20
#define OPL3_TREMOLO_ON 0x80
#define OPL3_VIBRATO_ON 0x40
#define OPL3_SUSTAIN_ON 0x20
#define OPL3_KSR 0x10 /* Key scaling rate */
#define OPL3_MULTIPLE_MASK 0x0f /* Frequency multiplier */
/*
* KSL/Total level (0x40 to 0x55)
*/
#define OPL3_REG_KSL_LEVEL 0x40
#define OPL3_KSL_MASK 0xc0 /* Envelope scaling bits */
#define OPL3_TOTAL_LEVEL_MASK 0x3f /* Strength (volume) of OP */
/*
* Attack / Decay rate (0x60 to 0x75)
*/
#define OPL3_REG_ATTACK_DECAY 0x60
#define OPL3_ATTACK_MASK 0xf0
#define OPL3_DECAY_MASK 0x0f
/*
* Sustain level / Release rate (0x80 to 0x95)
*/
#define OPL3_REG_SUSTAIN_RELEASE 0x80
#define OPL3_SUSTAIN_MASK 0xf0
#define OPL3_RELEASE_MASK 0x0f
/*
* Wave select (0xE0 to 0xF5)
*/
#define OPL3_REG_WAVE_SELECT 0xe0
#define OPL3_WAVE_SELECT_MASK 0x07
/*
* Offsets to the register banks for voices. Just add to the
* voice number to get the register number.
*
* F-Number low bits (0xA0 to 0xA8).
*/
#define OPL3_REG_FNUM_LOW 0xa0
/*
* F-number high bits / Key on / Block (octave) (0xB0 to 0xB8)
*/
#define OPL3_REG_KEYON_BLOCK 0xb0
#define OPL3_KEYON_BIT 0x20
#define OPL3_BLOCKNUM_MASK 0x1c
#define OPL3_FNUM_HIGH_MASK 0x03
/*
* Feedback / Connection (0xc0 to 0xc8)
*
* These registers have two new bits when the OPL-3 mode
* is selected. These bits controls connecting the voice
* to the stereo channels. For 4 OP voices this bit is
* defined in the second half of the voice (add 3 to the
* register offset).
*
* For 4 OP voices the connection bit is used in the
* both halves (gives 4 ways to connect the operators).
*/
#define OPL3_REG_FEEDBACK_CONNECTION 0xc0
#define OPL3_FEEDBACK_MASK 0x0e /* Valid just for 1st OP of a voice */
#define OPL3_CONNECTION_BIT 0x01
/*
* In the 4 OP mode there is four possible configurations how the
* operators can be connected together (in 2 OP modes there is just
* AM or FM). The 4 OP connection mode is defined by the rightmost
* bit of the FEEDBACK_CONNECTION (0xC0-0xC8) on the both halves.
*
* First half Second half Mode
*
* +---+
* v |
* 0 0 >+-1-+--2--3--4-->
*
*
*
* +---+
* | |
* 0 1 >+-1-+--2-+
* |->
* >--3----4-+
*
* +---+
* | |
* 1 0 >+-1-+-----+
* |->
* >--2--3--4-+
*
* +---+
* | |
* 1 1 >+-1-+--+
* |
* >--2--3-+->
* |
* >--4----+
*/
#define OPL3_STEREO_BITS 0x30 /* OPL-3 only */
#define OPL3_VOICE_TO_LEFT 0x10
#define OPL3_VOICE_TO_RIGHT 0x20
/*
*/
#define OPL3_LEFT 0x0000
#define OPL3_RIGHT 0x0100
#define OPL3_HW_AUTO 0x0000
#define OPL3_HW_OPL2 0x0200
#define OPL3_HW_OPL3 0x0300
#define OPL3_HW_OPL3_SV 0x0301 /* S3 SonicVibes */
#define OPL3_HW_OPL3_CS 0x0302 /* CS4232/CS4236+ */
#define OPL3_HW_OPL3_FM801 0x0303 /* FM801 */
#define OPL3_HW_OPL3_CS4281 0x0304 /* CS4281 */
#define OPL3_HW_OPL3_PC98 0x0305 /* PC9800 */
#define OPL3_HW_OPL4 0x0400 /* YMF278B/YMF295 */
#define OPL3_HW_OPL4_ML 0x0401 /* YMF704/YMF721 */
#define OPL3_HW_MASK 0xff00
#define MAX_OPL2_VOICES 9
#define MAX_OPL3_VOICES 18
typedef struct snd_opl3 opl3_t;
/*
* A structure to keep track of each hardware voice
*/
typedef struct snd_opl3_voice {
int state; /* status */
#define SNDRV_OPL3_ST_OFF 0 /* Not playing */
#define SNDRV_OPL3_ST_ON_2OP 1 /* 2op voice is allocated */
#define SNDRV_OPL3_ST_ON_4OP 2 /* 4op voice is allocated */
#define SNDRV_OPL3_ST_NOT_AVAIL -1 /* voice is not available */
unsigned int time; /* An allocation time */
unsigned char note; /* Note currently assigned to this voice */
unsigned long note_off; /* note-off time */
int note_off_check; /* check note-off time */
unsigned char keyon_reg; /* KON register shadow */
snd_midi_channel_t *chan; /* Midi channel for this note */
} snd_opl3_voice_t;
struct snd_opl3 {
unsigned long l_port;
unsigned long r_port;
struct resource *res_l_port;
struct resource *res_r_port;
unsigned short hardware;
/* hardware access */
void (*command) (opl3_t * opl3, unsigned short cmd, unsigned char val);
unsigned short timer_enable;
int seq_dev_num; /* sequencer device number */
snd_timer_t *timer1;
snd_timer_t *timer2;
spinlock_t timer_lock;
void *private_data;
void (*private_free)(opl3_t *);
spinlock_t reg_lock;
snd_card_t *card; /* The card that this belongs to */
int used; /* usage flag - exclusive */
unsigned char fm_mode; /* OPL mode, see SNDRV_DM_FM_MODE_XXX */
unsigned char rhythm; /* percussion mode flag */
unsigned char max_voices; /* max number of voices */
#if defined(CONFIG_SND_SEQUENCER) || defined(CONFIG_SND_SEQUENCER_MODULE)
#define SNDRV_OPL3_MODE_SYNTH 0 /* OSS - voices allocated by application */
#define SNDRV_OPL3_MODE_SEQ 1 /* ALSA - driver handles voice allocation */
int synth_mode; /* synth mode */
int seq_client;
snd_seq_device_t *seq_dev; /* sequencer device */
snd_midi_channel_set_t * chset;
#ifdef CONFIG_SND_SEQUENCER_OSS
snd_seq_device_t *oss_seq_dev; /* OSS sequencer device */
snd_midi_channel_set_t * oss_chset;
#endif
snd_seq_kinstr_ops_t fm_ops;
snd_seq_kinstr_list_t *ilist;
snd_opl3_voice_t voices[MAX_OPL3_VOICES]; /* Voices (OPL3 'channel') */
int use_time; /* allocation counter */
unsigned short connection_reg; /* connection reg shadow */
unsigned char drum_reg; /* percussion reg shadow */
spinlock_t voice_lock; /* Lock for voice access */
struct timer_list tlist; /* timer for note-offs and effects */
int sys_timer_status; /* system timer run status */
spinlock_t sys_timer_lock; /* Lock for system timer access */
#endif
struct semaphore access_mutex; /* locking */
};
/* opl3.c */
void snd_opl3_interrupt(snd_hwdep_t * hw);
int snd_opl3_new(snd_card_t *card, unsigned short hardware, opl3_t **ropl3);
int snd_opl3_init(opl3_t *opl3);
int snd_opl3_create(snd_card_t * card,
unsigned long l_port, unsigned long r_port,
unsigned short hardware,
int integrated,
opl3_t ** opl3);
int snd_opl3_timer_new(opl3_t * opl3, int timer1_dev, int timer2_dev);
int snd_opl3_hwdep_new(opl3_t * opl3, int device, int seq_device,
snd_hwdep_t ** rhwdep);
/* opl3_synth */
int snd_opl3_open(snd_hwdep_t * hw, struct file *file);
int snd_opl3_ioctl(snd_hwdep_t * hw, struct file *file,
unsigned int cmd, unsigned long arg);
int snd_opl3_release(snd_hwdep_t * hw, struct file *file);
void snd_opl3_reset(opl3_t * opl3);
#endif /* __SOUND_OPL3_H */
