/*
* mac80211 <-> driver interface
*
* Copyright 2002-2005, Devicescape Software, Inc.
* Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
* Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef MAC80211_H
#define MAC80211_H
#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/cfg80211.h>
/**
* DOC: Introduction
*
* mac80211 is the Linux stack for 802.11 hardware that implements
* only partial functionality in hard- or firmware. This document
* defines the interface between mac80211 and low-level hardware
* drivers.
*/
/**
* DOC: Calling mac80211 from interrupts
*
* Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
* called in hardware interrupt context. The low-level driver must not call any
* other functions in hardware interrupt context. If there is a need for such
* call, the low-level driver should first ACK the interrupt and perform the
* IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
* tasklet function.
*
* NOTE: If the driver opts to use the _irqsafe() functions, it may not also
* use the non-IRQ-safe functions!
*/
/**
* DOC: Warning
*
* If you're reading this document and not the header file itself, it will
* be incomplete because not all documentation has been converted yet.
*/
/**
* DOC: Frame format
*
* As a general rule, when frames are passed between mac80211 and the driver,
* they start with the IEEE 802.11 header and include the same octets that are
* sent over the air except for the FCS which should be calculated by the
* hardware.
*
* There are, however, various exceptions to this rule for advanced features:
*
* The first exception is for hardware encryption and decryption offload
* where the IV/ICV may or may not be generated in hardware.
*
* Secondly, when the hardware handles fragmentation, the frame handed to
* the driver from mac80211 is the MSDU, not the MPDU.
*
* Finally, for received frames, the driver is able to indicate that it has
* filled a radiotap header and put that in front of the frame; if it does
* not do so then mac80211 may add this under certain circumstances.
*/
/**
* DOC: mac80211 workqueue
*
* mac80211 provides its own workqueue for drivers and internal mac80211 use.
* The workqueue is a single threaded workqueue and can only be accessed by
* helpers for sanity checking. Drivers must ensure all work added onto the
* mac80211 workqueue should be cancelled on the driver stop() callback.
*
* mac80211 will flushed the workqueue upon interface removal and during
* suspend.
*
* All work performed on the mac80211 workqueue must not acquire the RTNL lock.
*
*/
/**
* enum ieee80211_max_queues - maximum number of queues
*
* @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
*/
enum ieee80211_max_queues {
IEEE80211_MAX_QUEUES = 4,
};
/**
* struct ieee80211_tx_queue_params - transmit queue configuration
*
* The information provided in this structure is required for QoS
* transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
*
* @aifs: arbitration interframe space [0..255]
* @cw_min: minimum contention window [a value of the form
* 2^n-1 in the range 1..32767]
* @cw_max: maximum contention window [like @cw_min]
* @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
* @uapsd: is U-APSD mode enabled for the queue
*/
struct ieee80211_tx_queue_params {
u16 txop;
u16 cw_min;
u16 cw_max;
u8 aifs;
bool uapsd;
};
struct ieee80211_low_level_stats {
unsigned int dot11ACKFailureCount;
unsigned int dot11RTSFailureCount;
unsigned int dot11FCSErrorCount;
unsigned int dot11RTSSuccessCount;
};
/**
* enum ieee80211_bss_change - BSS change notification flags
*
* These flags are used with the bss_info_changed() callback
* to indicate which BSS parameter changed.
*
* @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
* also implies a change in the AID.
* @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
* @BSS_CHANGED_ERP_PREAMBLE: preamble changed
* @BSS_CHANGED_ERP_SLOT: slot timing changed
* @BSS_CHANGED_HT: 802.11n parameters changed
* @BSS_CHANGED_BASIC_RATES: Basic rateset changed
* @BSS_CHANGED_BEACON_INT: Beacon interval changed
* @BSS_CHANGED_BSSID: BSSID changed, for whatever
* reason (IBSS and managed mode)
* @BSS_CHANGED_BEACON: Beacon data changed, retrieve
* new beacon (beaconing modes)
* @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
* enabled/disabled (beaconing modes)
* @BSS_CHANGED_CQM: Connection quality monitor config changed
* @BSS_CHANGED_IBSS: IBSS join status changed
* @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
* @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
* that it is only ever disabled for station mode.
* @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
BSS_CHANGED_ERP_CTS_PROT = 1<<1,
BSS_CHANGED_ERP_PREAMBLE = 1<<2,
BSS_CHANGED_ERP_SLOT = 1<<3,
BSS_CHANGED_HT = 1<<4,
BSS_CHANGED_BASIC_RATES = 1<<5,
BSS_CHANGED_BEACON_INT = 1<<6,
BSS_CHANGED_BSSID = 1<<7,
BSS_CHANGED_BEACON = 1<<8,
BSS_CHANGED_BEACON_ENABLED = 1<<9,
BSS_CHANGED_CQM = 1<<10,
BSS_CHANGED_IBSS = 1<<11,
BSS_CHANGED_ARP_FILTER = 1<<12,
BSS_CHANGED_QOS = 1<<13,
BSS_CHANGED_IDLE = 1<<14,
/* when adding here, make sure to change ieee80211_reconfig */
};
/*
* The maximum number of IPv4 addresses listed for ARP filtering. If the number
* of addresses for an interface increase beyond this value, hardware ARP
* filtering will be disabled.
*/
#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
/**
* struct ieee80211_bss_conf - holds the BSS's changing parameters
*
* This structure keeps information about a BSS (and an association
* to that BSS) that can change during the lifetime of the BSS.
*
* @assoc: association status
* @ibss_joined: indicates whether this station is part of an IBSS
* or not
* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
* @use_short_preamble: use 802.11b short preamble;
* if the hardware cannot handle this it must set the
* IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
* @use_short_slot: use short slot time (only relevant for ERP);
* if the hardware cannot handle this it must set the
* IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
* @dtim_period: num of beacons before the next DTIM, for beaconing,
* valid in station mode only while @assoc is true and if also
* requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf
* @ps_dtim_period)
* @timestamp: beacon timestamp
* @beacon_int: beacon interval
* @assoc_capability: capabilities taken from assoc resp
* @basic_rates: bitmap of basic rates, each bit stands for an
* index into the rate table configured by the driver in
* the current band.
* @bssid: The BSSID for this BSS
* @enable_beacon: whether beaconing should be enabled or not
* @channel_type: Channel type for this BSS -- the hardware might be
* configured for HT40+ while this BSS only uses no-HT, for
* example.
* @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
* This field is only valid when the channel type is one of the HT types.
* @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
* implies disabled
* @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
* @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
* may filter ARP queries targeted for other addresses than listed here.
* The driver must allow ARP queries targeted for all address listed here
* to pass through. An empty list implies no ARP queries need to pass.
* @arp_addr_cnt: Number of addresses currently on the list.
* @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may
* filter ARP queries based on the @arp_addr_list, if disabled, the
* hardware must not perform any ARP filtering. Note, that the filter will
* be enabled also in promiscuous mode.
* @qos: This is a QoS-enabled BSS.
* @idle: This interface is idle. There's also a global idle flag in the
* hardware config which may be more appropriate depending on what
* your driver/device needs to do.
*/
struct ieee80211_bss_conf {
const u8 *bssid;
/* association related data */
bool assoc, ibss_joined;
u16 aid;
/* erp related data */
bool use_cts_prot;
bool use_short_preamble;
bool use_short_slot;
bool enable_beacon;
u8 dtim_period;
u16 beacon_int;
u16 assoc_capability;
u64 timestamp;
u32 basic_rates;
u16 ht_operation_mode;
s32 cqm_rssi_thold;
u32 cqm_rssi_hyst;
enum nl80211_channel_type channel_type;
__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
u8 arp_addr_cnt;
bool arp_filter_enabled;
bool qos;
bool idle;
};
/**
* enum mac80211_tx_control_flags - flags to describe transmission information/status
*
* These flags are used with the @flags member of &ieee80211_tx_info.
*
* @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
* @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
* number to this frame, taking care of not overwriting the fragment
* number and increasing the sequence number only when the
* IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
* assign sequence numbers to QoS-data frames but cannot do so correctly
* for non-QoS-data and management frames because beacons need them from
* that counter as well and mac80211 cannot guarantee proper sequencing.
* If this flag is set, the driver should instruct the hardware to
* assign a sequence number to the frame or assign one itself. Cf. IEEE
* 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
* beacons and always be clear for frames without a sequence number field.
* @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
* @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
* station
* @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
* @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
* @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
* @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
* @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
* because the destination STA was in powersave mode. Note that to
* avoid race conditions, the filter must be set by the hardware or
* firmware upon receiving a frame that indicates that the station
* went to sleep (must be done on device to filter frames already on
* the queue) and may only be unset after mac80211 gives the OK for
* that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
* since only then is it guaranteed that no more frames are in the
* hardware queue.
* @IEEE80211_TX_STAT_ACK: Frame was acknowledged
* @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
* is for the whole aggregation.
* @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
* so consider using block ack request (BAR).
* @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
* set by rate control algorithms to indicate probe rate, will
* be cleared for fragmented frames (except on the last fragment)
* @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
* used to indicate that a pending frame requires TX processing before
* it can be sent out.
* @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
* used to indicate that a frame was already retried due to PS
* @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
* used to indicate frame should not be encrypted
* @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
* This frame is a response to a PS-poll frame and should be sent
* although the station is in powersave mode.
* @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
* transmit function after the current frame, this can be used
* by drivers to kick the DMA queue only if unset or when the
* queue gets full.
* @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
* after TX status because the destination was asleep, it must not
* be modified again (no seqno assignment, crypto, etc.)
* @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still
* has a radiotap header at skb->data.
* @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
* MLME command (internal to mac80211 to figure out whether to send TX
* status to user space)
* @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
* @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
* frame and selects the maximum number of streams that it can use.
*
* Note: If you have to add new flags to the enumeration, then don't
* forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
IEEE80211_TX_CTL_NO_ACK = BIT(2),
IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
IEEE80211_TX_CTL_AMPDU = BIT(6),
IEEE80211_TX_CTL_INJECTED = BIT(7),
IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
IEEE80211_TX_STAT_ACK = BIT(9),
IEEE80211_TX_STAT_AMPDU = BIT(10),
IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
IEEE80211_TX_INTFL_RETRIED = BIT(15),
IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
IEEE80211_TX_CTL_PSPOLL_RESPONSE = BIT(17),
IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20),
IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
IEEE80211_TX_CTL_LDPC = BIT(22),
IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
};
#define IEEE80211_TX_CTL_STBC_SHIFT 23
/*
* This definition is used as a mask to clear all temporary flags, which are
* set by the tx handlers for each transmission attempt by the mac80211 stack.
*/
#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \
IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
IEEE80211_TX_CTL_STBC)
/**
* enum mac80211_rate_control_flags - per-rate flags set by the
* Rate Control algorithm.
*
* These flags are set by the Rate control algorithm for each rate during tx,
* in the @flags member of struct ieee80211_tx_rate.
*
* @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
* @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
* This is set if the current BSS requires ERP protection.
* @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
* @IEEE80211_TX_RC_MCS: HT rate.
* @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
* Greenfield mode.
* @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
* @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
* adjacent 20 MHz channels, if the current channel type is
* NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
* @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
*/
enum mac80211_rate_control_flags {
IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
/* rate index is an MCS rate number instead of an index */
IEEE80211_TX_RC_MCS = BIT(3),
IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
IEEE80211_TX_RC_DUP_DATA = BIT(6),
IEEE80211_TX_RC_SHORT_GI = BIT(7),
};
/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES 5
/**
* struct ieee80211_tx_rate - rate selection/status
*
* @idx: rate index to attempt to send with
* @flags: rate control flags (&enum mac80211_rate_control_flags)
* @count: number of tries in this rate before going to the next rate
*
* A value of -1 for @idx indicates an invalid rate and, if used
* in an array of retry rates, that no more rates should be tried.
*
* When used for transmit status reporting, the driver should
* always report the rate along with the flags it used.
*
* &struct ieee80211_tx_info contains an array of these structs
* in the control information, and it will be filled by the rate
* control algorithm according to what should be sent. For example,
* if this array contains, in the format { <idx>, <count> } the
* information
* { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
* then this means that the frame should be transmitted
* up to twice at rate 3, up to twice at rate 2, and up to four
* times at rate 1 if it doesn't get acknowledged. Say it gets
* acknowledged by the peer after the fifth attempt, the status
* information should then contain
* { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
* since it was transmitted twice at rate 3, twice at rate 2
* and once at rate 1 after which we received an acknowledgement.
*/
struct ieee80211_tx_rate {
s8 idx;
u8 count;
u8 flags;
} __packed;
/**
* struct ieee80211_tx_info - skb transmit information
*
* This structure is placed in skb->cb for three uses:
* (1) mac80211 TX control - mac80211 tells the driver what to do
* (2) driver internal use (if applicable)
* (3) TX status information - driver tells mac80211 what happened
*
* The TX control's sta pointer is only valid during the ->tx call,
* it may be NULL.
*
* @flags: transmit info flags, defined above
* @band: the band to transmit on (use for checking for races)
* @antenna_sel_tx: antenna to use, 0 for automatic diversity
* @pad: padding, ignore
* @control: union for control data
* @status: union for status data
* @driver_data: array of driver_data pointers
* @ampdu_ack_len: number of acked aggregated frames.
* relevant only if IEEE80211_TX_STAT_AMPDU was set.
* @ampdu_len: number of aggregated frames.
* relevant only if IEEE80211_TX_STAT_AMPDU was set.
* @ack_signal: signal strength of the ACK frame
*/
struct ieee80211_tx_info {
/* common information */
u32 flags;
u8 band;
u8 antenna_sel_tx;
/* 2 byte hole */
u8 pad[2];
union {
struct {
union {
/* rate control */
struct {
struct ieee80211_tx_rate rates[
IEEE80211_TX_MAX_RATES];
s8 rts_cts_rate_idx;
};
/* only needed before rate control */
unsigned long jiffies;
};
/* NB: vif can be NULL for injected frames */
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
struct ieee80211_sta *sta;
} control;
struct {
struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
u8 ampdu_ack_len;
int ack_signal;
u8 ampdu_len;
/* 15 bytes free */
} status;
struct {
struct ieee80211_tx_rate driver_rates[
IEEE80211_TX_MAX_RATES];
void *rate_driver_data[
IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
};
void *driver_data[
IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
};
};
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
return (struct ieee80211_tx_info *)skb->cb;
}
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
return (struct ieee80211_rx_status *)skb->cb;
}
/**
* ieee80211_tx_info_clear_status - clear TX status
*
* @info: The &struct ieee80211_tx_info to be cleared.
*
* When the driver passes an skb back to mac80211, it must report
* a number of things in TX status. This function clears everything
* in the TX status but the rate control information (it does clear
* the count since you need to fill that in anyway).
*
* NOTE: You can only use this function if you do NOT use
* info->driver_data! Use info->rate_driver_data
* instead if you need only the less space that allows.
*/
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
int i;
BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
offsetof(struct ieee80211_tx_info, control.rates));
BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
offsetof(struct ieee80211_tx_info, driver_rates));
BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
/* clear the rate counts */
for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
info->status.rates[i].count = 0;
BUILD_BUG_ON(
offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
memset(&info->status.ampdu_ack_len, 0,
sizeof(struct ieee80211_tx_info) -
offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}
/**
* enum mac80211_rx_flags - receive flags
*
* These flags are used with the @flag member of &struct ieee80211_rx_status.
* @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
* Use together with %RX_FLAG_MMIC_STRIPPED.
* @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
* @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
* verification has been done by the hardware.
* @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
* If this flag is set, the stack cannot do any replay detection
* hence the driver or hardware will have to do that.
* @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
* the frame.
* @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
* the frame.
* @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
* is valid. This is useful in monitor mode and necessary for beacon frames
* to enable IBSS merging.
* @RX_FLAG_SHORTPRE: Short preamble was used for this frame
* @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
* @RX_FLAG_40MHZ: HT40 (40 MHz) was used
* @RX_FLAG_SHORT_GI: Short guard interval was used
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
RX_FLAG_DECRYPTED = 1<<1,
RX_FLAG_MMIC_STRIPPED = 1<<3,
RX_FLAG_IV_STRIPPED = 1<<4,
RX_FLAG_FAILED_FCS_CRC = 1<<5,
RX_FLAG_FAILED_PLCP_CRC = 1<<6,
RX_FLAG_TSFT = 1<<7,
RX_FLAG_SHORTPRE = 1<<8,
RX_FLAG_HT = 1<<9,
RX_FLAG_40MHZ = 1<<10,
RX_FLAG_SHORT_GI = 1<<11,
};
/**
* struct ieee80211_rx_status - receive status
*
* The low-level driver should provide this information (the subset
* supported by hardware) to the 802.11 code with each received
* frame, in the skb's control buffer (cb).
*
* @mactime: value in microseconds of the 64-bit Time Synchronization Function
* (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
* @band: the active band when this frame was received
* @freq: frequency the radio was tuned to when receiving this frame, in MHz
* @signal: signal strength when receiving this frame, either in dBm, in dB or
* unspecified depending on the hardware capabilities flags
* @IEEE80211_HW_SIGNAL_*
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates or MCS index if
* HT rates are use (RX_FLAG_HT)
* @flag: %RX_FLAG_*
* @rx_flags: internal RX flags for mac80211
*/
struct ieee80211_rx_status {
u64 mactime;
enum ieee80211_band band;
int freq;
int signal;
int antenna;
int rate_idx;
int flag;
unsigned int rx_flags;
};
/**
* enum ieee80211_conf_flags - configuration flags
*
* Flags to define PHY configuration options
*
* @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
* to determine for example whether to calculate timestamps for packets
* or not, do not use instead of filter flags!
* @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
* This is the power save mode defined by IEEE 802.11-2007 section 11.2,
* meaning that the hardware still wakes up for beacons, is able to
* transmit frames and receive the possible acknowledgment frames.
* Not to be confused with hardware specific wakeup/sleep states,
* driver is responsible for that. See the section "Powersave support"
* for more.
* @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
* the driver should be prepared to handle configuration requests but
* may turn the device off as much as possible. Typically, this flag will
* be set when an interface is set UP but not associated or scanning, but
* it can also be unset in that case when monitor interfaces are active.
* @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
* operating channel.
*/
enum ieee80211_conf_flags {
IEEE80211_CONF_MONITOR = (1<<0),
IEEE80211_CONF_PS = (1<<1),
IEEE80211_CONF_IDLE = (1<<2),
IEEE80211_CONF_OFFCHANNEL = (1<<3),
};
/**
* enum ieee80211_conf_changed - denotes which configuration changed
*
* @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
* @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
* @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
* @IEEE80211_CONF_CHANGE_POWER: the TX power changed
* @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
* @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
* @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
* @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
*/
enum ieee80211_conf_changed {
IEEE80211_CONF_CHANGE_SMPS = BIT(1),
IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
IEEE80211_CONF_CHANGE_PS = BIT(4),
IEEE80211_CONF_CHANGE_POWER = BIT(5),
IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
IEEE80211_CONF_CHANGE_IDLE = BIT(8),
};
/**
* enum ieee80211_smps_mode - spatial multiplexing power save mode
*
* @IEEE80211_SMPS_AUTOMATIC: automatic
* @IEEE80211_SMPS_OFF: off
* @IEEE80211_SMPS_STATIC: static
* @IEEE80211_SMPS_DYNAMIC: dynamic
* @IEEE80211_SMPS_NUM_MODES: internal, don't use
*/
enum ieee80211_smps_mode {
IEEE80211_SMPS_AUTOMATIC,
IEEE80211_SMPS_OFF,
IEEE80211_SMPS_STATIC,
IEEE80211_SMPS_DYNAMIC,
/* keep last */
IEEE80211_SMPS_NUM_MODES,
};
/**
* struct ieee80211_conf - configuration of the device
*
* This struct indicates how the driver shall configure the hardware.
*
* @flags: configuration flags defined above
*
* @listen_interval: listen interval in units of beacon interval
* @max_sleep_period: the maximum number of beacon intervals to sleep for
* before checking the beacon for a TIM bit (managed mode only); this
* value will be only achievable between DTIM frames, the hardware
* needs to check for the multicast traffic bit in DTIM beacons.
* This variable is valid only when the CONF_PS flag is set.
* @ps_dtim_period: The DTIM period of the AP we're connected to, for use
* in power saving. Power saving will not be enabled until a beacon
* has been received and the DTIM period is known.
* @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
* powersave documentation below. This variable is valid only when
* the CONF_PS flag is set.
*
* @power_level: requested transmit power (in dBm)
*
* @channel: the channel to tune to
* @channel_type: the channel (HT) type
*
* @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
* (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
* but actually means the number of transmissions not the number of retries
* @short_frame_max_tx_count: Maximum number of transmissions for a "short"
* frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
* number of transmissions not the number of retries
*
* @smps_mode: spatial multiplexing powersave mode; note that
* %IEEE80211_SMPS_STATIC is used when the device is not
* configured for an HT channel
*/
struct ieee80211_conf {
u32 flags;
int power_level, dynamic_ps_timeout;
int max_sleep_period;
u16 listen_interval;
u8 ps_dtim_period;
u8 long_frame_max_tx_count, short_frame_max_tx_count;
struct ieee80211_channel *channel;
enum nl80211_channel_type channel_type;
enum ieee80211_smps_mode smps_mode;
};
/**
* struct ieee80211_channel_switch - holds the channel switch data
*
* The information provided in this structure is required for channel switch
* operation.
*
* @timestamp: value in microseconds of the 64-bit Time Synchronization
* Function (TSF) timer when the frame containing the channel switch
* announcement was received. This is simply the rx.mactime parameter
* the driver passed into mac80211.
* @block_tx: Indicates whether transmission must be blocked before the
* scheduled channel switch, as indicated by the AP.
* @channel: the new channel to switch to
* @count: the number of TBTT's until the channel switch event
*/
struct ieee80211_channel_switch {
u64 timestamp;
bool block_tx;
struct ieee80211_channel *channel;
u8 count;
};
/**
* struct ieee80211_vif - per-interface data
*
* Data in this structure is continually present for driver
* use during the life of a virtual interface.
*
* @type: type of this virtual interface
* @bss_conf: BSS configuration for this interface, either our own
* or the BSS we're associated to
* @addr: address of this interface
* @p2p: indicates whether this AP or STA interface is a p2p
* interface, i.e. a GO or p2p-sta respectively
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
*/
struct ieee80211_vif {
enum nl80211_iftype type;
struct ieee80211_bss_conf bss_conf;
u8 addr[ETH_ALEN];
bool p2p;
/* must be last */
u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
return vif->type == NL80211_IFTYPE_MESH_POINT;
#endif
return false;
}
/**
* enum ieee80211_key_flags - key flags
*
* These flags are used for communication about keys between the driver
* and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
*
* @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
* that the STA this key will be used with could be using QoS.
* @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
* driver to indicate that it requires IV generation for this
* particular key.
* @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
* the driver for a TKIP key if it requires Michael MIC
* generation in software.
* @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
* that the key is pairwise rather then a shared key.
* @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
* CCMP key if it requires CCMP encryption of management frames (MFP) to
* be done in software.
*/
enum ieee80211_key_flags {
IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
IEEE80211_KEY_FLAG_SW_MGMT = 1<<4,
};
/**
* struct ieee80211_key_conf - key information
*
* This key information is given by mac80211 to the driver by
* the set_key() callback in &struct ieee80211_ops.
*
* @hw_key_idx: To be set by the driver, this is the key index the driver
* wants to be given when a frame is transmitted and needs to be
* encrypted in hardware.
* @cipher: The key's cipher suite selector.
* @flags: key flags, see &enum ieee80211_key_flags.
* @keyidx: the key index (0-3)
* @keylen: key material length
* @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
* data block:
* - Temporal Encryption Key (128 bits)
* - Temporal Authenticator Tx MIC Key (64 bits)
* - Temporal Authenticator Rx MIC Key (64 bits)
* @icv_len: The ICV length for this key type
* @iv_len: The IV length for this key type
*/
struct ieee80211_key_conf {
u32 cipher;
u8 icv_len;
u8 iv_len;
u8 hw_key_idx;
u8 flags;
s8 keyidx;
u8 keylen;
u8 key[0];
};
/**
* enum set_key_cmd - key command
*
* Used with the set_key() callback in &struct ieee80211_ops, this
* indicates whether a key is being removed or added.
*
* @SET_KEY: a key is set
* @DISABLE_KEY: a key must be disabled
*/
enum set_key_cmd {
SET_KEY, DISABLE_KEY,
};
/**
* struct ieee80211_sta - station table entry
*
* A station table entry represents a station we are possibly
* communicating with. Since stations are RCU-managed in
* mac80211, any ieee80211_sta pointer you get access to must
* either be protected by rcu_read_lock() explicitly or implicitly,
* or you must take good care to not use such a pointer after a
* call to your sta_remove callback that removed it.
*
* @addr: MAC address
* @aid: AID we assigned to the station if we're an AP
* @supp_rates: Bitmap of supported rates (per band)
* @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *), size is determined in hw information.
*/
struct ieee80211_sta {
u32 supp_rates[IEEE80211_NUM_BANDS];
u8 addr[ETH_ALEN];
u16 aid;
struct ieee80211_sta_ht_cap ht_cap;
/* must be last */
u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};
/**
* enum sta_notify_cmd - sta notify command
*
* Used with the sta_notify() callback in &struct ieee80211_ops, this
* indicates if an associated station made a power state transition.
*
* @STA_NOTIFY_SLEEP: a station is now sleeping
* @STA_NOTIFY_AWAKE: a sleeping station woke up
*/
enum sta_notify_cmd {
STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};
/**
* enum ieee80211_tkip_key_type - get tkip key
*
* Used by drivers which need to get a tkip key for skb. Some drivers need a
* phase 1 key, others need a phase 2 key. A single function allows the driver
* to get the key, this enum indicates what type of key is required.
*
* @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
* @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
*/
enum ieee80211_tkip_key_type {
IEEE80211_TKIP_P1_KEY,
IEEE80211_TKIP_P2_KEY,
};
/**
* enum ieee80211_hw_flags - hardware flags
*
* These flags are used to indicate hardware capabilities to
* the stack. Generally, flags here should have their meaning
* done in a way that the simplest hardware doesn't need setting
* any particular flags. There are some exceptions to this rule,
* however, so you are advised to review these flags carefully.
*
* @IEEE80211_HW_HAS_RATE_CONTROL:
* The hardware or firmware includes rate control, and cannot be
* controlled by the stack. As such, no rate control algorithm
* should be instantiated, and the TX rate reported to userspace
* will be taken from the TX status instead of the rate control
* algorithm.
* Note that this requires that the driver implement a number of
* callbacks so it has the correct information, it needs to have
* the @set_rts_threshold callback and must look at the BSS config
* @use_cts_prot for G/N protection, @use_short_slot for slot
* timing in 2.4 GHz and @use_short_preamble for preambles for
* CCK frames.
*
* @IEEE80211_HW_RX_INCLUDES_FCS:
* Indicates that received frames passed to the stack include
* the FCS at the end.
*
* @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
* Some wireless LAN chipsets buffer broadcast/multicast frames
* for power saving stations in the hardware/firmware and others
* rely on the host system for such buffering. This option is used
* to configure the IEEE 802.11 upper layer to buffer broadcast and
* multicast frames when there are power saving stations so that
* the driver can fetch them with ieee80211_get_buffered_bc().
*
* @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
* Hardware is not capable of short slot operation on the 2.4 GHz band.
*
* @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
* Hardware is not capable of receiving frames with short preamble on
* the 2.4 GHz band.
*
* @IEEE80211_HW_SIGNAL_UNSPEC:
* Hardware can provide signal values but we don't know its units. We
* expect values between 0 and @max_signal.
* If possible please provide dB or dBm instead.
*
* @IEEE80211_HW_SIGNAL_DBM:
* Hardware gives signal values in dBm, decibel difference from
* one milliwatt. This is the preferred method since it is standardized
* between different devices. @max_signal does not need to be set.
*
* @IEEE80211_HW_SPECTRUM_MGMT:
* Hardware supports spectrum management defined in 802.11h
* Measurement, Channel Switch, Quieting, TPC
*
* @IEEE80211_HW_AMPDU_AGGREGATION:
* Hardware supports 11n A-MPDU aggregation.
*
* @IEEE80211_HW_SUPPORTS_PS:
* Hardware has power save support (i.e. can go to sleep).
*
* @IEEE80211_HW_PS_NULLFUNC_STACK:
* Hardware requires nullfunc frame handling in stack, implies
* stack support for dynamic PS.
*
* @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
* Hardware has support for dynamic PS.
*
* @IEEE80211_HW_MFP_CAPABLE:
* Hardware supports management frame protection (MFP, IEEE 802.11w).
*
* @IEEE80211_HW_BEACON_FILTER:
* Hardware supports dropping of irrelevant beacon frames to
* avoid waking up cpu.
*
* @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
* Hardware supports static spatial multiplexing powersave,
* ie. can turn off all but one chain even on HT connections
* that should be using more chains.
*
* @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
* Hardware supports dynamic spatial multiplexing powersave,
* ie. can turn off all but one chain and then wake the rest
* up as required after, for example, rts/cts handshake.
*
* @IEEE80211_HW_SUPPORTS_UAPSD:
* Hardware supports Unscheduled Automatic Power Save Delivery
* (U-APSD) in managed mode. The mode is configured with
* conf_tx() operation.
*
* @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
* Hardware can provide ack status reports of Tx frames to
* the stack.
*
* @IEEE80211_HW_CONNECTION_MONITOR:
* The hardware performs its own connection monitoring, including
* periodic keep-alives to the AP and probing the AP on beacon loss.
* When this flag is set, signaling beacon-loss will cause an immediate
* change to disassociated state.
*
* @IEEE80211_HW_SUPPORTS_CQM_RSSI:
* Hardware can do connection quality monitoring - i.e. it can monitor
* connection quality related parameters, such as the RSSI level and
* provide notifications if configured trigger levels are reached.
*
* @IEEE80211_HW_NEED_DTIM_PERIOD:
* This device needs to know the DTIM period for the BSS before
* associating.
*
* @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
* per-station GTKs as used by IBSS RSN or during fast transition. If
* the device doesn't support per-station GTKs, but can be asked not
* to decrypt group addressed frames, then IBSS RSN support is still
* possible but software crypto will be used. Advertise the wiphy flag
* only in that case.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
IEEE80211_HW_SIGNAL_DBM = 1<<6,
IEEE80211_HW_NEED_DTIM_PERIOD = 1<<7,
IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
IEEE80211_HW_SUPPORTS_PS = 1<<10,
IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
IEEE80211_HW_MFP_CAPABLE = 1<<13,
IEEE80211_HW_BEACON_FILTER = 1<<14,
IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15,
IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16,
IEEE80211_HW_SUPPORTS_UAPSD = 1<<17,
IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18,
IEEE80211_HW_CONNECTION_MONITOR = 1<<19,
IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20,
IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21,
};
/**
* struct ieee80211_hw - hardware information and state
*
* This structure contains the configuration and hardware
* information for an 802.11 PHY.
*
* @wiphy: This points to the &struct wiphy allocated for this
* 802.11 PHY. You must fill in the @perm_addr and @dev
* members of this structure using SET_IEEE80211_DEV()
* and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
* bands (with channels, bitrates) are registered here.
*
* @conf: &struct ieee80211_conf, device configuration, don't use.
*
* @priv: pointer to private area that was allocated for driver use
* along with this structure.
*
* @flags: hardware flags, see &enum ieee80211_hw_flags.
*
* @extra_tx_headroom: headroom to reserve in each transmit skb
* for use by the driver (e.g. for transmit headers.)
*
* @channel_change_time: time (in microseconds) it takes to change channels.
*
* @max_signal: Maximum value for signal (rssi) in RX information, used
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @max_listen_interval: max listen interval in units of beacon interval
* that HW supports
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
* queues need to have configurable access parameters.
*
* @rate_control_algorithm: rate control algorithm for this hardware.
* If unset (NULL), the default algorithm will be used. Must be
* set before calling ieee80211_register_hw().
*
* @vif_data_size: size (in bytes) of the drv_priv data area
* within &struct ieee80211_vif.
* @sta_data_size: size (in bytes) of the drv_priv data area
* within &struct ieee80211_sta.
*
* @max_rates: maximum number of alternate rate retry stages the hw
* can handle.
* @max_report_rates: maximum number of alternate rate retry stages
* the hw can report back.
* @max_rate_tries: maximum number of tries for each stage
*
* @napi_weight: weight used for NAPI polling. You must specify an
* appropriate value here if a napi_poll operation is provided
* by your driver.
*/
struct ieee80211_hw {
struct ieee80211_conf conf;
struct wiphy *wiphy;
const char *rate_control_algorithm;
void *priv;
u32 flags;
unsigned int extra_tx_headroom;
int channel_change_time;
int vif_data_size;
int sta_data_size;
int napi_weight;
u16 queues;
u16 max_listen_interval;
s8 max_signal;
u8 max_rates;
u8 max_report_rates;
u8 max_rate_tries;
};
/**
* wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
*
* @wiphy: the &struct wiphy which we want to query
*
* mac80211 drivers can use this to get to their respective
* &struct ieee80211_hw. Drivers wishing to get to their own private
* structure can then access it via hw->priv. Note that mac802111 drivers should
* not use wiphy_priv() to try to get their private driver structure as this
* is already used internally by mac80211.
*/
struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
/**
* SET_IEEE80211_DEV - set device for 802.11 hardware
*
* @hw: the &struct ieee80211_hw to set the device for
* @dev: the &struct device of this 802.11 device
*/
static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
set_wiphy_dev(hw->wiphy, dev);
}
/**
* SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
*
* @hw: the &struct ieee80211_hw to set the MAC address for
* @addr: the address to set
*/
static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
{
memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}
static inline struct ieee80211_rate *
ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
const struct ieee80211_tx_info *c)
{
if (WARN_ON(c->control.rates[0].idx < 0))
return NULL;
return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
}
static inline struct ieee80211_rate *
ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
const struct ieee80211_tx_info *c)
{
if (c->control.rts_cts_rate_idx < 0)
return NULL;
return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
}
static inline struct ieee80211_rate *
ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
const struct ieee80211_tx_info *c, int idx)
{
if (c->control.rates[idx + 1].idx < 0)
return NULL;
return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
}
/**
* DOC: Hardware crypto acceleration
*
* mac80211 is capable of taking advantage of many hardware
* acceleration designs for encryption and decryption operations.
*
* The set_key() callback in the &struct ieee80211_ops for a given
* device is called to enable hardware acceleration of encryption and
* decryption. The callback takes a @sta parameter that will be NULL
* for default keys or keys used for transmission only, or point to
* the station information for the peer for individual keys.
* Multiple transmission keys with the same key index may be used when
* VLANs are configured for an access point.
*
* When transmitting, the TX control data will use the @hw_key_idx
* selected by the driver by modifying the &struct ieee80211_key_conf
* pointed to by the @key parameter to the set_key() function.
*
* The set_key() call for the %SET_KEY command should return 0 if
* the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
* added; if you return 0 then hw_key_idx must be assigned to the
* hardware key index, you are free to use the full u8 range.
*
* When the cmd is %DISABLE_KEY then it must succeed.
*
* Note that it is permissible to not decrypt a frame even if a key
* for it has been uploaded to hardware, the stack will not make any
* decision based on whether a key has been uploaded or not but rather
* based on the receive flags.
*
* The &struct ieee80211_key_conf structure pointed to by the @key
* parameter is guaranteed to be valid until another call to set_key()
* removes it, but it can only be used as a cookie to differentiate
* keys.
*
* In TKIP some HW need to be provided a phase 1 key, for RX decryption
* acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
* handler.
* The update_tkip_key() call updates the driver with the new phase 1 key.
* This happens everytime the iv16 wraps around (every 65536 packets). The
* set_key() call will happen only once for each key (unless the AP did
* rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
* provided by update_tkip_key only. The trigger that makes mac80211 call this
* handler is software decryption with wrap around of iv16.
*/
/**
* DOC: Powersave support
*
* mac80211 has support for various powersave implementations.
*
* First, it can support hardware that handles all powersaving by itself,
* such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
* flag. In that case, it will be told about the desired powersave mode
* with the %IEEE80211_CONF_PS flag depending on the association status.
* The hardware must take care of sending nullfunc frames when necessary,
* i.e. when entering and leaving powersave mode. The hardware is required
* to look at the AID in beacons and signal to the AP that it woke up when
* it finds traffic directed to it.
*
* %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
* IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
* with hardware wakeup and sleep states. Driver is responsible for waking
* up the hardware before issuing commands to the hardware and putting it
* back to sleep at appropriate times.
*
* When PS is enabled, hardware needs to wakeup for beacons and receive the
* buffered multicast/broadcast frames after the beacon. Also it must be
* possible to send frames and receive the acknowledment frame.
*
* Other hardware designs cannot send nullfunc frames by themselves and also
* need software support for parsing the TIM bitmap. This is also supported
* by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
* %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
* required to pass up beacons. The hardware is still required to handle
* waking up for multicast traffic; if it cannot the driver must handle that
* as best as it can, mac80211 is too slow to do that.
*
* Dynamic powersave is an extension to normal powersave in which the
* hardware stays awake for a user-specified period of time after sending a
* frame so that reply frames need not be buffered and therefore delayed to
* the next wakeup. It's compromise of getting good enough latency when
* there's data traffic and still saving significantly power in idle
* periods.
*
* Dynamic powersave is simply supported by mac80211 enabling and disabling
* PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
* flag and mac80211 will handle everything automatically. Additionally,
* hardware having support for the dynamic PS feature may set the
* %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
* dynamic PS mode itself. The driver needs to look at the
* @dynamic_ps_timeout hardware configuration value and use it that value
* whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
* dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
* enabled whenever user has enabled powersave.
*
* Some hardware need to toggle a single shared antenna between WLAN and
* Bluetooth to facilitate co-existence. These types of hardware set
* limitations on the use of host controlled dynamic powersave whenever there
* is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the
* driver may request temporarily going into full power save, in order to
* enable toggling the antenna between BT and WLAN. If the driver requests
* disabling dynamic powersave, the @dynamic_ps_timeout value will be
* temporarily set to zero until the driver re-enables dynamic powersave.
*
* Driver informs U-APSD client support by enabling
* %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the
* uapsd paramater in conf_tx() operation. Hardware needs to send the QoS
* Nullfunc frames and stay awake until the service period has ended. To
* utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
* from that AC are transmitted with powersave enabled.
*
* Note: U-APSD client mode is not yet supported with
* %IEEE80211_HW_PS_NULLFUNC_STACK.
*/
/**
* DOC: Beacon filter support
*
* Some hardware have beacon filter support to reduce host cpu wakeups
* which will reduce system power consumption. It usuallly works so that
* the firmware creates a checksum of the beacon but omits all constantly
* changing elements (TSF, TIM etc). Whenever the checksum changes the
* beacon is forwarded to the host, otherwise it will be just dropped. That
* way the host will only receive beacons where some relevant information
* (for example ERP protection or WMM settings) have changed.
*
* Beacon filter support is advertised with the %IEEE80211_HW_BEACON_FILTER
* hardware capability. The driver needs to enable beacon filter support
* whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
* power save is enabled, the stack will not check for beacon loss and the
* driver needs to notify about loss of beacons with ieee80211_beacon_loss().
*
* The time (or number of beacons missed) until the firmware notifies the
* driver of a beacon loss event (which in turn causes the driver to call
* ieee80211_beacon_loss()) should be configurable and will be controlled
* by mac80211 and the roaming algorithm in the future.
*
* Since there may be constantly changing information elements that nothing
* in the software stack cares about, we will, in the future, have mac80211
* tell the driver which information elements are interesting in the sense
* that we want to see changes in them. This will include
* - a list of information element IDs
* - a list of OUIs for the vendor information element
*
* Ideally, the hardware would filter out any beacons without changes in the
* requested elements, but if it cannot support that it may, at the expense
* of some efficiency, filter out only a subset. For example, if the device
* doesn't support checking for OUIs it should pass up all changes in all
* vendor information elements.
*
* Note that change, for the sake of simplification, also includes information
* elements appearing or disappearing from the beacon.
*
* Some hardware supports an "ignore list" instead, just make sure nothing
* that was requested is on the ignore list, and include commonly changing
* information element IDs in the ignore list, for example 11 (BSS load) and
* the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
* 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
* it could also include some currently unused IDs.
*
*
* In addition to these capabilities, hardware should support notifying the
* host of changes in the beacon RSSI. This is relevant to implement roaming
* when no traffic is flowing (when traffic is flowing we see the RSSI of
* the received data packets). This can consist in notifying the host when
* the RSSI changes significantly or when it drops below or rises above
* configurable thresholds. In the future these thresholds will also be
* configured by mac80211 (which gets them from userspace) to implement
* them as the roaming algorithm requires.
*
* If the hardware cannot implement this, the driver should ask it to
* periodically pass beacon frames to the host so that software can do the
* signal strength threshold checking.
*/
/**
* DOC: Spatial multiplexing power save
*
* SMPS (Spatial multiplexing power save) is a mechanism to conserve
* power in an 802.11n implementation. For details on the mechanism
* and rationale, please refer to 802.11 (as amended by 802.11n-2009)
* "11.2.3 SM power save".
*
* The mac80211 implementation is capable of sending action frames
* to update the AP about the station's SMPS mode, and will instruct
* the driver to enter the specific mode. It will also announce the
* requested SMPS mode during the association handshake. Hardware
* support for this feature is required, and can be indicated by
* hardware flags.
*
* The default mode will be "automatic", which nl80211/cfg80211
* defines to be dynamic SMPS in (regular) powersave, and SMPS
* turned off otherwise.
*
* To support this feature, the driver must set the appropriate
* hardware support flags, and handle the SMPS flag to the config()
* operation. It will then with this mechanism be instructed to
* enter the requested SMPS mode while associated to an HT AP.
*/
/**
* DOC: Frame filtering
*
* mac80211 requires to see many management frames for proper
* operation, and users may want to see many more frames when
* in monitor mode. However, for best CPU usage and power consumption,
* having as few frames as possible percolate through the stack is
* desirable. Hence, the hardware should filter as much as possible.
*
* To achieve this, mac80211 uses filter flags (see below) to tell
* the driver's configure_filter() function which frames should be
* passed to mac80211 and which should be filtered out.
*
* Before configure_filter() is invoked, the prepare_multicast()
* callback is invoked with the parameters @mc_count and @mc_list
* for the combined multicast address list of all virtual interfaces.
* It's use is optional, and it returns a u64 that is passed to
* configure_filter(). Additionally, configure_filter() has the
* arguments @changed_flags telling which flags were changed and
* @total_flags with the new flag states.
*
* If your device has no multicast address filters your driver will
* need to check both the %FIF_ALLMULTI flag and the @mc_count
* parameter to see whether multicast frames should be accepted
* or dropped.
*
* All unsupported flags in @total_flags must be cleared.
* Hardware does not support a flag if it is incapable of _passing_
* the frame to the stack. Otherwise the driver must ignore
* the flag, but not clear it.
* You must _only_ clear the flag (announce no support for the
* flag to mac80211) if you are not able to pass the packet type
* to the stack (so the hardware always filters it).
* So for example, you should clear @FIF_CONTROL, if your hardware
* always filters control frames. If your hardware always passes
* control frames to the kernel and is incapable of filtering them,
* you do _not_ clear the @FIF_CONTROL flag.
* This rule applies to all other FIF flags as well.
*/
/**
* enum ieee80211_filter_flags - hardware filter flags
*
* These flags determine what the filter in hardware should be
* programmed to let through and what should not be passed to the
* stack. It is always safe to pass more frames than requested,
* but this has negative impact on power consumption.
*
* @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
* think of the BSS as your network segment and then this corresponds
* to the regular ethernet device promiscuous mode.
*
* @FIF_ALLMULTI: pass all multicast frames, this is used if requested
* by the user or if the hardware is not capable of filtering by
* multicast address.
*
* @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
* %RX_FLAG_FAILED_FCS_CRC for them)
*
* @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
* the %RX_FLAG_FAILED_PLCP_CRC for them
*
* @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
* to the hardware that it should not filter beacons or probe responses
* by BSSID. Filtering them can greatly reduce the amount of processing
* mac80211 needs to do and the amount of CPU wakeups, so you should
* honour this flag if possible.
*
* @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS
* is not set then only those addressed to this station.
*
* @FIF_OTHER_BSS: pass frames destined to other BSSes
*
* @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only
* those addressed to this station.
*
* @FIF_PROBE_REQ: pass probe request frames
*/
enum ieee80211_filter_flags {
FIF_PROMISC_IN_BSS = 1<<0,
FIF_ALLMULTI = 1<<1,
FIF_FCSFAIL = 1<<2,
FIF_PLCPFAIL = 1<<3,
FIF_BCN_PRBRESP_PROMISC = 1<<4,
FIF_CONTROL = 1<<5,
FIF_OTHER_BSS = 1<<6,
FIF_PSPOLL = 1<<7,
FIF_PROBE_REQ = 1<<8,
};
/**
* enum ieee80211_ampdu_mlme_action - A-MPDU actions
*
* These flags are used with the ampdu_action() callback in
* &struct ieee80211_ops to indicate which action is needed.
*
* Note that drivers MUST be able to deal with a TX aggregation
* session being stopped even before they OK'ed starting it by
* calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
* might receive the addBA frame and send a delBA right away!
*
* @IEEE80211_AMPDU_RX_START: start Rx aggregation
* @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
* @IEEE80211_AMPDU_TX_START: start Tx aggregation
* @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
* @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
*/
enum ieee80211_ampdu_mlme_action {
IEEE80211_AMPDU_RX_START,
IEEE80211_AMPDU_RX_STOP,
IEEE80211_AMPDU_TX_START,
IEEE80211_AMPDU_TX_STOP,
IEEE80211_AMPDU_TX_OPERATIONAL,
};
/**
* struct ieee80211_ops - callbacks from mac80211 to the driver
*
* This structure contains various callbacks that the driver may
* handle or, in some cases, must handle, for example to configure
* the hardware to a new channel or to transmit a frame.
*
* @tx: Handler that 802.11 module calls for each transmitted frame.
* skb contains the buffer starting from the IEEE 802.11 header.
* The low-level driver should send the frame out based on
* configuration in the TX control data. This handler should,
* preferably, never fail and stop queues appropriately, more
* importantly, however, it must never fail for A-MPDU-queues.
* This function should return NETDEV_TX_OK except in very
* limited cases.
* Must be implemented and atomic.
*
* @start: Called before the first netdevice attached to the hardware
* is enabled. This should turn on the hardware and must turn on
* frame reception (for possibly enabled monitor interfaces.)
* Returns negative error codes, these may be seen in userspace,
* or zero.
* When the device is started it should not have a MAC address
* to avoid acknowledging frames before a non-monitor device
* is added.
* Must be implemented and can sleep.
*
* @stop: Called after last netdevice attached to the hardware
* is disabled. This should turn off the hardware (at least
* it must turn off frame reception.)
* May be called right after add_interface if that rejects
* an interface. If you added any work onto the mac80211 workqueue
* you should ensure to cancel it on this callback.
* Must be implemented and can sleep.
*
* @add_interface: Called when a netdevice attached to the hardware is
* enabled. Because it is not called for monitor mode devices, @start
* and @stop must be implemented.
* The driver should perform any initialization it needs before
* the device can be enabled. The initial configuration for the
* interface is given in the conf parameter.
* The callback may refuse to add an interface by returning a
* negative error code (which will be seen in userspace.)
* Must be implemented and can sleep.
*
* @change_interface: Called when a netdevice changes type. This callback
* is optional, but only if it is supported can interface types be
* switched while the interface is UP. The callback may sleep.
* Note that while an interface is being switched, it will not be
* found by the interface iteration callbacks.
*
* @remove_interface: Notifies a driver that an interface is going down.
* The @stop callback is called after this if it is the last interface
* and no monitor interfaces are present.
* When all interfaces are removed, the MAC address in the hardware
* must be cleared so the device no longer acknowledges packets,
* the mac_addr member of the conf structure is, however, set to the
* MAC address of the device going away.
* Hence, this callback must be implemented. It can sleep.
*
* @config: Handler for configuration requests. IEEE 802.11 code calls this
* function to change hardware configuration, e.g., channel.
* This function should never fail but returns a negative error code
* if it does. The callback can sleep.
*
* @bss_info_changed: Handler for configuration requests related to BSS
* parameters that may vary during BSS's lifespan, and may affect low
* level driver (e.g. assoc/disassoc status, erp parameters).
* This function should not be used if no BSS has been set, unless
* for association indication. The @changed parameter indicates which
* of the bss parameters has changed when a call is made. The callback
* can sleep.
*
* @prepare_multicast: Prepare for multicast filter configuration.
* This callback is optional, and its return value is passed
* to configure_filter(). This callback must be atomic.
*
* @configure_filter: Configure the device's RX filter.
* See the section "Frame filtering" for more information.
* This callback must be implemented and can sleep.
*
* @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
* must be set or cleared for a given STA. Must be atomic.
*
* @set_key: See the section "Hardware crypto acceleration"
* This callback is only called between add_interface and
* remove_interface calls, i.e. while the given virtual interface
* is enabled.
* Returns a negative error code if the key can't be added.
* The callback can sleep.
*
* @update_tkip_key: See the section "Hardware crypto acceleration"
* This callback will be called in the context of Rx. Called for drivers
* which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
* The callback must be atomic.
*
* @hw_scan: Ask the hardware to service the scan request, no need to start
* the scan state machine in stack. The scan must honour the channel
* configuration done by the regulatory agent in the wiphy's
* registered bands. The hardware (or the driver) needs to make sure
* that power save is disabled.
* The @req ie/ie_len members are rewritten by mac80211 to contain the
* entire IEs after the SSID, so that drivers need not look at these
* at all but just send them after the SSID -- mac80211 includes the
* (extended) supported rates and HT information (where applicable).
* When the scan finishes, ieee80211_scan_completed() must be called;
* note that it also must be called when the scan cannot finish due to
* any error unless this callback returned a negative error code.
* The callback can sleep.
*
* @sw_scan_start: Notifier function that is called just before a software scan
* is started. Can be NULL, if the driver doesn't need this notification.
* The callback can sleep.
*
* @sw_scan_complete: Notifier function that is called just after a
* software scan finished. Can be NULL, if the driver doesn't need
* this notification.
* The callback can sleep.
*
* @get_stats: Return low-level statistics.
* Returns zero if statistics are available.
* The callback can sleep.
*
* @get_tkip_seq: If your device implements TKIP encryption in hardware this
* callback should be provided to read the TKIP transmit IVs (both IV32
* and IV16) for the given key from hardware.
* The callback must be atomic.
*
* @set_rts_threshold: Configuration of RTS threshold (if device needs it)
* The callback can sleep.
*
* @sta_add: Notifies low level driver about addition of an associated station,
* AP, IBSS/WDS/mesh peer etc. This callback can sleep.
*
* @sta_remove: Notifies low level driver about removal of an associated
* station, AP, IBSS/WDS/mesh peer etc. This callback can sleep.
*
* @sta_notify: Notifies low level driver about power state transition of an
* associated station, AP, IBSS/WDS/mesh peer etc. Must be atomic.
*
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
* bursting) for a hardware TX queue.
* Returns a negative error code on failure.
* The callback can sleep.
*
* @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
* this is only used for IBSS mode BSSID merging and debugging. Is not a
* required function.
* The callback can sleep.
*
* @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
* Currently, this is only used for IBSS mode debugging. Is not a
* required function.
* The callback can sleep.
*
* @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
* with other STAs in the IBSS. This is only used in IBSS mode. This
* function is optional if the firmware/hardware takes full care of
* TSF synchronization.
* The callback can sleep.
*
* @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
* This is needed only for IBSS mode and the result of this function is
* used to determine whether to reply to Probe Requests.
* Returns non-zero if this device sent the last beacon.
* The callback can sleep.
*
* @ampdu_action: Perform a certain A-MPDU action
* The RA/TID combination determines the destination and TID we want
* the ampdu action to be performed for. The action is defined through
* ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
* is the first frame we expect to perform the action on. Notice
* that TX/RX_STOP can pass NULL for this parameter.
* Returns a negative error code on failure.
* The callback can sleep.
*
* @get_survey: Return per-channel survey information
*
* @rfkill_poll: Poll rfkill hardware state. If you need this, you also
* need to set wiphy->rfkill_poll to %true before registration,
* and need to call wiphy_rfkill_set_hw_state() in the callback.
* The callback can sleep.
*
* @set_coverage_class: Set slot time for given coverage class as specified
* in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
* accordingly. This callback is not required and may sleep.
*
* @testmode_cmd: Implement a cfg80211 test mode command.
* The callback can sleep.
*
* @flush: Flush all pending frames from the hardware queue, making sure
* that the hardware queues are empty. If the parameter @drop is set
* to %true, pending frames may be dropped. The callback can sleep.
*
* @channel_switch: Drivers that need (or want) to offload the channel
* switch operation for CSAs received from the AP may implement this
* callback. They must then call ieee80211_chswitch_done() to indicate
* completion of the channel switch.
*
* @napi_poll: Poll Rx queue for incoming data frames.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
int (*start)(struct ieee80211_hw *hw);
void (*stop)(struct ieee80211_hw *hw);
int (*add_interface)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
int (*change_interface)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
enum nl80211_iftype new_type, bool p2p);
void (*remove_interface)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
int (*config)(struct ieee80211_hw *hw, u32 changed);
void (*bss_info_changed)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *info,
u32 changed);
u64 (*prepare_multicast)(struct ieee80211_hw *hw,
struct netdev_hw_addr_list *mc_list);
void (*configure_filter)(struct ieee80211_hw *hw,
unsigned int changed_flags,
unsigned int *total_flags,
u64 multicast);
int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
bool set);
int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
struct ieee80211_vif *vif, struct ieee80211_sta *sta,
struct ieee80211_key_conf *key);
void (*update_tkip_key)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_key_conf *conf,
struct ieee80211_sta *sta,
u32 iv32, u16 *phase1key);
int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct cfg80211_scan_request *req);
void (*sw_scan_start)(struct ieee80211_hw *hw);
void (*sw_scan_complete)(struct ieee80211_hw *hw);
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
u32 *iv32, u16 *iv16);
int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct ieee80211_sta *sta);
int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct ieee80211_sta *sta);
void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
enum sta_notify_cmd, struct ieee80211_sta *sta);
int (*conf_tx)(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params);
u64 (*get_tsf)(struct ieee80211_hw *hw);
void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf);
void (*reset_tsf)(struct ieee80211_hw *hw);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
int (*ampdu_action)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
enum ieee80211_ampdu_mlme_action action,
struct ieee80211_sta *sta, u16 tid, u16 *ssn);
int (*get_survey)(struct ieee80211_hw *hw, int idx,
struct survey_info *survey);
void (*rfkill_poll)(struct ieee80211_hw *hw);
void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
#ifdef CONFIG_NL80211_TESTMODE
int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len);
#endif
void (*flush)(struct ieee80211_hw *hw, bool drop);
void (*channel_switch)(struct ieee80211_hw *hw,
struct ieee80211_channel_switch *ch_switch);
int (*napi_poll)(struct ieee80211_hw *hw, int budget);
};
/**
* ieee80211_alloc_hw - Allocate a new hardware device
*
* This must be called once for each hardware device. The returned pointer
* must be used to refer to this device when calling other functions.
* mac80211 allocates a private data area for the driver pointed to by
* @priv in &struct ieee80211_hw, the size of this area is given as
* @priv_data_len.
*
* @priv_data_len: length of private data
* @ops: callbacks for this device
*/
struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
const struct ieee80211_ops *ops);
/**
* ieee80211_register_hw - Register hardware device
*
* You must call this function before any other functions in
* mac80211. Note that before a hardware can be registered, you
* need to fill the contained wiphy's information.
*
* @hw: the device to register as returned by ieee80211_alloc_hw()
*/
int ieee80211_register_hw(struct ieee80211_hw *hw);
#ifdef CONFIG_MAC80211_LEDS
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
#endif
/**
* ieee80211_get_tx_led_name - get name of TX LED
*
* mac80211 creates a transmit LED trigger for each wireless hardware
* that can be used to drive LEDs if your driver registers a LED device.
* This function returns the name (or %NULL if not configured for LEDs)
* of the trigger so you can automatically link the LED device.
*
* @hw: the hardware to get the LED trigger name for
*/
static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
return __ieee80211_get_tx_led_name(hw);
#else
return NULL;
#endif
}
/**
* ieee80211_get_rx_led_name - get name of RX LED
*
* mac80211 creates a receive LED trigger for each wireless hardware
* that can be used to drive LEDs if your driver registers a LED device.
* This function returns the name (or %NULL if not configured for LEDs)
* of the trigger so you can automatically link the LED device.
*
* @hw: the hardware to get the LED trigger name for
*/
static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
return __ieee80211_get_rx_led_name(hw);
#else
return NULL;
#endif
}
/**
* ieee80211_get_assoc_led_name - get name of association LED
*
* mac80211 creates a association LED trigger for each wireless hardware
* that can be used to drive LEDs if your driver registers a LED device.
* This function returns the name (or %NULL if not configured for LEDs)
* of the trigger so you can automatically link the LED device.
*
* @hw: the hardware to get the LED trigger name for
*/
static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
return __ieee80211_get_assoc_led_name(hw);
#else
return NULL;
#endif
}
/**
* ieee80211_get_radio_led_name - get name of radio LED
*
* mac80211 creates a radio change LED trigger for each wireless hardware
* that can be used to drive LEDs if your driver registers a LED device.
* This function returns the name (or %NULL if not configured for LEDs)
* of the trigger so you can automatically link the LED device.
*
* @hw: the hardware to get the LED trigger name for
*/
static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
return __ieee80211_get_radio_led_name(hw);
#else
return NULL;
#endif
}
/**
* ieee80211_unregister_hw - Unregister a hardware device
*
* This function instructs mac80211 to free allocated resources
* and unregister netdevices from the networking subsystem.
*
* @hw: the hardware to unregister
*/
void ieee80211_unregister_hw(struct ieee80211_hw *hw);
/**
* ieee80211_free_hw - free hardware descriptor
*
* This function frees everything that was allocated, including the
* private data for the driver. You must call ieee80211_unregister_hw()
* before calling this function.
*
* @hw: the hardware to free
*/
void ieee80211_free_hw(struct ieee80211_hw *hw);
/**
* ieee80211_restart_hw - restart hardware completely
*
* Call this function when the hardware was restarted for some reason
* (hardware error, ...) and the driver is unable to restore its state
* by itself. mac80211 assumes that at this point the driver/hardware
* is completely uninitialised and stopped, it starts the process by
* calling the ->start() operation. The driver will need to reset all
* internal state that it has prior to calling this function.
*
* @hw: the hardware to restart
*/
void ieee80211_restart_hw(struct ieee80211_hw *hw);
/** ieee80211_napi_schedule - schedule NAPI poll
*
* Use this function to schedule NAPI polling on a device.
*
* @hw: the hardware to start polling
*/
void ieee80211_napi_schedule(struct ieee80211_hw *hw);
/** ieee80211_napi_complete - complete NAPI polling
*
* Use this function to finish NAPI polling on a device.
*
* @hw: the hardware to stop polling
*/
void ieee80211_napi_complete(struct ieee80211_hw *hw);
/**
* ieee80211_rx - receive frame
*
* Use this function to hand received frames to mac80211. The receive
* buffer in @skb must start with an IEEE 802.11 header. In case of a
* paged @skb is used, the driver is recommended to put the ieee80211
* header of the frame on the linear part of the @skb to avoid memory
* allocation and/or memcpy by the stack.
*
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls to
* this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
* mixed for a single hardware.
*
* In process context use instead ieee80211_rx_ni().
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
*/
void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
/**
* ieee80211_rx_irqsafe - receive frame
*
* Like ieee80211_rx() but can be called in IRQ context
* (internally defers to a tasklet.)
*
* Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
* be mixed for a single hardware.
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
*/
void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
/**
* ieee80211_rx_ni - receive frame (in process context)
*
* Like ieee80211_rx() but can be called in process context
* (internally disables bottom halves).
*
* Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
* not be mixed for a single hardware.
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
*/
static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
struct sk_buff *skb)
{
local_bh_disable();
ieee80211_rx(hw, skb);
local_bh_enable();
}
/*
* The TX headroom reserved by mac80211 for its own tx_status functions.
* This is enough for the radiotap header.
*/
#define IEEE80211_TX_STATUS_HEADROOM 13
/**
* ieee80211_tx_status - transmit status callback
*
* Call this function for all transmitted frames after they have been
* transmitted. It is permissible to not call this function for
* multicast frames but this can affect statistics.
*
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls
* to this function and ieee80211_tx_status_irqsafe() may not be mixed
* for a single hardware.
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
*/
void ieee80211_tx_status(struct ieee80211_hw *hw,
struct sk_buff *skb);
/**
* ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
*
* Like ieee80211_tx_status() but can be called in IRQ context
* (internally defers to a tasklet.)
*
* Calls to this function and ieee80211_tx_status() may not be mixed for a
* single hardware.
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
*/
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
struct sk_buff *skb);
/**
* ieee80211_beacon_get_tim - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @tim_offset: pointer to variable that will receive the TIM IE offset.
* Set to 0 if invalid (in non-AP modes).
* @tim_length: pointer to variable that will receive the TIM IE length,
* (including the ID and length bytes!).
* Set to 0 if invalid (in non-AP modes).
*
* If the driver implements beaconing modes, it must use this function to
* obtain the beacon frame/template.
*
* If the beacon frames are generated by the host system (i.e., not in
* hardware/firmware), the driver uses this function to get each beacon
* frame from mac80211 -- it is responsible for calling this function
* before the beacon is needed (e.g. based on hardware interrupt).
*
* If the beacon frames are generated by the device, then the driver
* must use the returned beacon as the template and change the TIM IE
* according to the current DTIM parameters/TIM bitmap.
*
* The driver is responsible for freeing the returned skb.
*/
struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
u16 *tim_offset, u16 *tim_length);
/**
* ieee80211_beacon_get - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* See ieee80211_beacon_get_tim().
*/
static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
}
/**
* ieee80211_pspoll_get - retrieve a PS Poll template
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* Creates a PS Poll a template which can, for example, uploaded to
* hardware. The template must be updated after association so that correct
* AID, BSSID and MAC address is used.
*
* Note: Caller (or hardware) is responsible for setting the
* &IEEE80211_FCTL_PM bit.
*/
struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
/**
* ieee80211_nullfunc_get - retrieve a nullfunc template
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* Creates a Nullfunc template which can, for example, uploaded to
* hardware. The template must be updated after association so that correct
* BSSID and address is used.
*
* Note: Caller (or hardware) is responsible for setting the
* &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
*/
struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
/**
* ieee80211_probereq_get - retrieve a Probe Request template
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @ssid: SSID buffer
* @ssid_len: length of SSID
* @ie: buffer containing all IEs except SSID for the template
* @ie_len: length of the IE buffer
*
* Creates a Probe Request template which can, for example, be uploaded to
* hardware.
*/
struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
const u8 *ssid, size_t ssid_len,
const u8 *ie, size_t ie_len);
/**
* ieee80211_rts_get - RTS frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @frame: pointer to the frame that is going to be protected by the RTS.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_info of the frame.
* @rts: The buffer where to store the RTS frame.
*
* If the RTS frames are generated by the host system (i.e., not in
* hardware/firmware), the low-level driver uses this function to receive
* the next RTS frame from the 802.11 code. The low-level is responsible
* for calling this function before and RTS frame is needed.
*/
void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_rts *rts);
/**
* ieee80211_rts_duration - Get the duration field for an RTS frame
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @frame_len: the length of the frame that is going to be protected by the RTS.
* @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the RTS is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif, size_t frame_len,
const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_ctstoself_get - CTS-to-self frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @frame: pointer to the frame that is going to be protected by the CTS-to-self.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_info of the frame.
* @cts: The buffer where to store the CTS-to-self frame.
*
* If the CTS-to-self frames are generated by the host system (i.e., not in
* hardware/firmware), the low-level driver uses this function to receive
* the next CTS-to-self frame from the 802.11 code. The low-level is responsible
* for calling this function before and CTS-to-self frame is needed.
*/
void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_cts *cts);
/**
* ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
* @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the CTS-to-self is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
size_t frame_len,
const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_generic_frame_duration - Calculate the duration field for a frame
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @frame_len: the length of the frame.
* @rate: the rate at which the frame is going to be transmitted.
*
* Calculate the duration field of some generic frame, given its
* length and transmission rate (in 100kbps).
*/
__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
size_t frame_len,
struct ieee80211_rate *rate);
/**
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* Function for accessing buffered broadcast and multicast frames. If
* hardware/firmware does not implement buffering of broadcast/multicast
* frames when power saving is used, 802.11 code buffers them in the host
* memory. The low-level driver uses this function to fetch next buffered
* frame. In most cases, this is used when generating beacon frame. This
* function returns a pointer to the next buffered skb or NULL if no more
* buffered frames are available.
*
* Note: buffered frames are returned only after DTIM beacon frame was
* generated with ieee80211_beacon_get() and the low-level driver must thus
* call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
* NULL if the previous generated beacon was not DTIM, so the low-level driver
* does not need to check for DTIM beacons separately and should be able to
* use common code for all beacons.
*/
struct sk_buff *
ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
/**
* ieee80211_get_tkip_key - get a TKIP rc4 for skb
*
* This function computes a TKIP rc4 key for an skb. It computes
* a phase 1 key if needed (iv16 wraps around). This function is to
* be used by drivers which can do HW encryption but need to compute
* to phase 1/2 key in SW.
*
* @keyconf: the parameter passed with the set key
* @skb: the skb for which the key is needed
* @type: TBD
* @key: a buffer to which the key will be written
*/
void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf,
struct sk_buff *skb,
enum ieee80211_tkip_key_type type, u8 *key);
/**
* ieee80211_wake_queue - wake specific queue
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @queue: queue number (counted from zero).
*
* Drivers should use this function instead of netif_wake_queue.
*/
void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
/**
* ieee80211_stop_queue - stop specific queue
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @queue: queue number (counted from zero).
*
* Drivers should use this function instead of netif_stop_queue.
*/
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
/**
* ieee80211_queue_stopped - test status of the queue
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @queue: queue number (counted from zero).
*
* Drivers should use this function instead of netif_stop_queue.
*/
int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
/**
* ieee80211_stop_queues - stop all queues
* @hw: pointer as obtained from ieee80211_alloc_hw().
*
* Drivers should use this function instead of netif_stop_queue.
*/
void ieee80211_stop_queues(struct ieee80211_hw *hw);
/**
* ieee80211_wake_queues - wake all queues
* @hw: pointer as obtained from ieee80211_alloc_hw().
*
* Drivers should use this function instead of netif_wake_queue.
*/
void ieee80211_wake_queues(struct ieee80211_hw *hw);
/**
* ieee80211_scan_completed - completed hardware scan
*
* When hardware scan offload is used (i.e. the hw_scan() callback is
* assigned) this function needs to be called by the driver to notify
* mac80211 that the scan finished. This function can be called from
* any context, including hardirq context.
*
* @hw: the hardware that finished the scan
* @aborted: set to true if scan was aborted
*/
void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
/**
* ieee80211_iterate_active_interfaces - iterate active interfaces
*
* This function iterates over the interfaces associated with a given
* hardware that are currently active and calls the callback for them.
* This function allows the iterator function to sleep, when the iterator
* function is atomic @ieee80211_iterate_active_interfaces_atomic can
* be used.
* Does not iterate over a new interface during add_interface()
*
* @hw: the hardware struct of which the interfaces should be iterated over
* @iterator: the iterator function to call
* @data: first argument of the iterator function
*/
void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
void (*iterator)(void *data, u8 *mac,
struct ieee80211_vif *vif),
void *data);
/**
* ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
*
* This function iterates over the interfaces associated with a given
* hardware that are currently active and calls the callback for them.
* This function requires the iterator callback function to be atomic,
* if that is not desired, use @ieee80211_iterate_active_interfaces instead.
* Does not iterate over a new interface during add_interface()
*
* @hw: the hardware struct of which the interfaces should be iterated over
* @iterator: the iterator function to call, cannot sleep
* @data: first argument of the iterator function
*/
void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
void (*iterator)(void *data,
u8 *mac,
struct ieee80211_vif *vif),
void *data);
/**
* ieee80211_queue_work - add work onto the mac80211 workqueue
*
* Drivers and mac80211 use this to add work onto the mac80211 workqueue.
* This helper ensures drivers are not queueing work when they should not be.
*
* @hw: the hardware struct for the interface we are adding work for
* @work: the work we want to add onto the mac80211 workqueue
*/
void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
/**
* ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
*
* Drivers and mac80211 use this to queue delayed work onto the mac80211
* workqueue.
*
* @hw: the hardware struct for the interface we are adding work for
* @dwork: delayable work to queue onto the mac80211 workqueue
* @delay: number of jiffies to wait before queueing
*/
void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
struct delayed_work *dwork,
unsigned long delay);
/**
* ieee80211_start_tx_ba_session - Start a tx Block Ack session.
* @sta: the station for which to start a BA session
* @tid: the TID to BA on.
*
* Return: success if addBA request was sent, failure otherwise
*
* Although mac80211/low level driver/user space application can estimate
* the need to start aggregation on a certain RA/TID, the session level
* will be managed by the mac80211.
*/
int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
/**
* ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
* @vif: &struct ieee80211_vif pointer from the add_interface callback
* @ra: receiver address of the BA session recipient.
* @tid: the TID to BA on.
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session. It can be called
* from any context.
*/
void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
u16 tid);
/**
* ieee80211_stop_tx_ba_session - Stop a Block Ack session.
* @sta: the station whose BA session to stop
* @tid: the TID to stop BA.
*
* Return: negative error if the TID is invalid, or no aggregation active
*
* Although mac80211/low level driver/user space application can estimate
* the need to stop aggregation on a certain RA/TID, the session level
* will be managed by the mac80211.
*/
int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
/**
* ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
* @vif: &struct ieee80211_vif pointer from the add_interface callback
* @ra: receiver address of the BA session recipient.
* @tid: the desired TID to BA on.
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session tear down. It
* can be called from any context.
*/
void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
u16 tid);
/**
* ieee80211_find_sta - find a station
*
* @vif: virtual interface to look for station on
* @addr: station's address
*
* This function must be called under RCU lock and the
* resulting pointer is only valid under RCU lock as well.
*/
struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
const u8 *addr);
/**
* ieee80211_find_sta_by_ifaddr - find a station on hardware
*
* @hw: pointer as obtained from ieee80211_alloc_hw()
* @addr: remote station's address
* @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
*
* This function must be called under RCU lock and the
* resulting pointer is only valid under RCU lock as well.
*
* NOTE: You may pass NULL for localaddr, but then you will just get
* the first STA that matches the remote address 'addr'.
* We can have multiple STA associated with multiple
* logical stations (e.g. consider a station connecting to another
* BSSID on the same AP hardware without disconnecting first).
* In this case, the result of this method with localaddr NULL
* is not reliable.
*
* DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
*/
struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
const u8 *addr,
const u8 *localaddr);
/**
* ieee80211_sta_block_awake - block station from waking up
* @hw: the hardware
* @pubsta: the station
* @block: whether to block or unblock
*
* Some devices require that all frames that are on the queues
* for a specific station that went to sleep are flushed before
* a poll response or frames after the station woke up can be
* delivered to that it. Note that such frames must be rejected
* by the driver as filtered, with the appropriate status flag.
*
* This function allows implementing this mode in a race-free
* manner.
*
* To do this, a driver must keep track of the number of frames
* still enqueued for a specific station. If this number is not
* zero when the station goes to sleep, the driver must call
* this function to force mac80211 to consider the station to
* be asleep regardless of the station's actual state. Once the
* number of outstanding frames reaches zero, the driver must
* call this function again to unblock the station. That will
* cause mac80211 to be able to send ps-poll responses, and if
* the station queried in the meantime then frames will also
* be sent out as a result of this. Additionally, the driver
* will be notified that the station woke up some time after
* it is unblocked, regardless of whether the station actually
* woke up while blocked or not.
*/
void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
struct ieee80211_sta *pubsta, bool block);
/**
* ieee80211_beacon_loss - inform hardware does not receive beacons
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and
* %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
* hardware is not receiving beacons with this function.
*/
void ieee80211_beacon_loss(struct ieee80211_vif *vif);
/**
* ieee80211_connection_loss - inform hardware has lost connection to the AP
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and
* %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
* needs to inform if the connection to the AP has been lost.
*
* This function will cause immediate change to disassociated state,
* without connection recovery attempts.
*/
void ieee80211_connection_loss(struct ieee80211_vif *vif);
/**
* ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* Some hardware require full power save to manage simultaneous BT traffic
* on the WLAN frequency. Full PSM is required periodically, whenever there are
* burst of BT traffic. The hardware gets information of BT traffic via
* hardware co-existence lines, and consequentially requests mac80211 to
* (temporarily) enter full psm.
* This function will only temporarily disable dynamic PS, not enable PSM if
* it was not already enabled.
* The driver must make sure to re-enable dynamic PS using
* ieee80211_enable_dyn_ps() if the driver has disabled it.
*
*/
void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif);
/**
* ieee80211_enable_dyn_ps - restore dynamic psm after being disabled
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
*
* This function restores dynamic PS after being temporarily disabled via
* ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must
* be coupled with an eventual call to this function.
*
*/
void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif);
/**
* ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
* rssi threshold triggered
*
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @rssi_event: the RSSI trigger event type
* @gfp: context flags
*
* When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality
* monitoring is configured with an rssi threshold, the driver will inform
* whenever the rssi level reaches the threshold.
*/
void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
enum nl80211_cqm_rssi_threshold_event rssi_event,
gfp_t gfp);
/**
* ieee80211_chswitch_done - Complete channel switch process
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @success: make the channel switch successful or not
*
* Complete the channel switch post-process: set the new operational channel
* and wake up the suspended queues.
*/
void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
/**
* ieee80211_request_smps - request SM PS transition
* @vif: &struct ieee80211_vif pointer from the add_interface callback.
* @smps_mode: new SM PS mode
*
* This allows the driver to request an SM PS transition in managed
* mode. This is useful when the driver has more information than
* the stack about possible interference, for example by bluetooth.
*/
void ieee80211_request_smps(struct ieee80211_vif *vif,
enum ieee80211_smps_mode smps_mode);
/**
* ieee80211_key_removed - disable hw acceleration for key
* @key_conf: The key hw acceleration should be disabled for
*
* This allows drivers to indicate that the given key has been
* removed from hardware acceleration, due to a new key that
* was added. Don't use this if the key can continue to be used
* for TX, if the key restriction is on RX only it is permitted
* to keep the key for TX only and not call this function.
*
* Due to locking constraints, it may only be called during
* @set_key. This function must be allowed to sleep, and the
* key it tries to disable may still be used until it returns.
*/
void ieee80211_key_removed(struct ieee80211_key_conf *key_conf);
/* Rate control API */
/**
* enum rate_control_changed - flags to indicate which parameter changed
*
* @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have
* changed, rate control algorithm can update its internal state if needed.
*/
enum rate_control_changed {
IEEE80211_RC_HT_CHANGED = BIT(0)
};
/**
* struct ieee80211_tx_rate_control - rate control information for/from RC algo
*
* @hw: The hardware the algorithm is invoked for.
* @sband: The band this frame is being transmitted on.
* @bss_conf: the current BSS configuration
* @reported_rate: The rate control algorithm can fill this in to indicate
* which rate should be reported to userspace as the current rate and
* used for rate calculations in the mesh network.
* @rts: whether RTS will be used for this frame because it is longer than the
* RTS threshold
* @short_preamble: whether mac80211 will request short-preamble transmission
* if the selected rate supports it
* @max_rate_idx: user-requested maximum rate (not MCS for now)
* (deprecated; this will be removed once drivers get updated to use
* rate_idx_mask)
* @rate_idx_mask: user-requested rate mask (not MCS for now)
* @skb: the skb that will be transmitted, the control information in it needs
* to be filled in
* @ap: whether this frame is sent out in AP mode
*/
struct ieee80211_tx_rate_control {
struct ieee80211_hw *hw;
struct ieee80211_supported_band *sband;
struct ieee80211_bss_conf *bss_conf;
struct sk_buff *skb;
struct ieee80211_tx_rate reported_rate;
bool rts, short_preamble;
u8 max_rate_idx;
u32 rate_idx_mask;
bool ap;
};
struct rate_control_ops {
struct module *module;
const char *name;
void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
void (*free)(void *priv);
void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta, void *priv_sta);
void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta,
void *priv_sta, u32 changed,
enum nl80211_channel_type oper_chan_type);
void (*free_sta)(void *priv, struct ieee80211_sta *sta,
void *priv_sta);
void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta, void *priv_sta,
struct sk_buff *skb);
void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
struct ieee80211_tx_rate_control *txrc);
void (*add_sta_debugfs)(void *priv, void *priv_sta,
struct dentry *dir);
void (*remove_sta_debugfs)(void *priv, void *priv_sta);
};
static inline int rate_supported(struct ieee80211_sta *sta,
enum ieee80211_band band,
int index)
{
return (sta == NULL || sta->supp_rates[band] & BIT(index));
}
/**
* rate_control_send_low - helper for drivers for management/no-ack frames
*
* Rate control algorithms that agree to use the lowest rate to
* send management frames and NO_ACK data with the respective hw
* retries should use this in the beginning of their mac80211 get_rate
* callback. If true is returned the rate control can simply return.
* If false is returned we guarantee that sta and sta and priv_sta is
* not null.
*
* Rate control algorithms wishing to do more intelligent selection of
* rate for multicast/broadcast frames may choose to not use this.
*
* @sta: &struct ieee80211_sta pointer to the target destination. Note
* that this may be null.
* @priv_sta: private rate control structure. This may be null.
* @txrc: rate control information we sholud populate for mac80211.
*/
bool rate_control_send_low(struct ieee80211_sta *sta,
void *priv_sta,
struct ieee80211_tx_rate_control *txrc);
static inline s8
rate_lowest_index(struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta)
{
int i;
for (i = 0; i < sband->n_bitrates; i++)
if (rate_supported(sta, sband->band, i))
return i;
/* warn when we cannot find a rate. */
WARN_ON(1);
return 0;
}
static inline
bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta)
{
unsigned int i;
for (i = 0; i < sband->n_bitrates; i++)
if (rate_supported(sta, sband->band, i))
return true;
return false;
}
int ieee80211_rate_control_register(struct rate_control_ops *ops);
void ieee80211_rate_control_unregister(struct rate_control_ops *ops);
static inline bool
conf_is_ht20(struct ieee80211_conf *conf)
{
return conf->channel_type == NL80211_CHAN_HT20;
}
static inline bool
conf_is_ht40_minus(struct ieee80211_conf *conf)
{
return conf->channel_type == NL80211_CHAN_HT40MINUS;
}
static inline bool
conf_is_ht40_plus(struct ieee80211_conf *conf)
{
return conf->channel_type == NL80211_CHAN_HT40PLUS;
}
static inline bool
conf_is_ht40(struct ieee80211_conf *conf)
{
return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf);
}
static inline bool
conf_is_ht(struct ieee80211_conf *conf)
{
return conf->channel_type != NL80211_CHAN_NO_HT;
}
static inline enum nl80211_iftype
ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
{
if (p2p) {
switch (type) {
case NL80211_IFTYPE_STATION:
return NL80211_IFTYPE_P2P_CLIENT;
case NL80211_IFTYPE_AP:
return NL80211_IFTYPE_P2P_GO;
default:
break;
}
}
return type;
}
static inline enum nl80211_iftype
ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
{
return ieee80211_iftype_p2p(vif->type, vif->p2p);
}
#endif /* MAC80211_H */
