blob: 423d592c55d5a6827e6b3719b0a7b7e570e2099d (
plain) (
tree)
|
|
/*
* pci_regs.h
*
* PCI standard defines
* Copyright 1994, Drew Eckhardt
* Copyright 1997--1999 Martin Mares <mj@ucw.cz>
*
* For more information, please consult the following manuals (look at
* http://www.pcisig.com/ for how to get them):
*
* PCI BIOS Specification
* PCI Local Bus Specification
* PCI to PCI Bridge Specification
* PCI System Design Guide
*
* For hypertransport information, please consult the following manuals
* from http://www.hypertransport.org
*
* The Hypertransport I/O Link Specification
*/
#ifndef LINUX_PCI_REGS_H
#define LINUX_PCI_REGS_H
/*
* Under PCI, each device has 256 bytes of configuration address space,
* of which the first 64 bytes are standardized as follows:
*/
#define PCI_VENDOR_ID 0x00 /* 16 bits */
#define PCI_DEVICE_ID 0x02 /* 16 bits */
#define PCI_COMMAND 0x04 /* 16 bits */
#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */
#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */
#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */
#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */
#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */
#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */
#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */
#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */
#define PCI_COMMAND_SERR 0x100 /* Enable SERR */
#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */
#define PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
#define PCI_STATUS 0x06 /* 16 bits */
#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */
#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */
#define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */
#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */
#define PCI_STATUS_PARITY 0x100 /* Detected parity error */
#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */
#define PCI_STATUS_DEVSEL_FAST 0x000
#define PCI_STATUS_DEVSEL_MEDIUM 0x200
#define PCI_STATUS_DEVSEL_SLOW 0x400
#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8 revision */
#define PCI_REVISION_ID 0x08 /* Revision ID */
#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */
#define PCI_CLASS_DEVICE 0x0a /* Device class */
#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */
#define PCI_LATENCY_TIMER 0x0d /* 8 bits */
#define PCI_HEADER_TYPE 0x0e /* 8 bits */
#define PCI_HEADER_TYPE_NORMAL 0
#define PCI_HEADER_TYPE_BRIDGE 1
#define PCI_HEADER_TYPE_CARDBUS 2
#define PCI_BIST 0x0f /* 8 bits */
#define PCI_BIST_CODE_MASK 0x0f /* Return result */
#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */
#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */
/*
* Base addresses specify locations in memory or I/O space.
* Decoded size can be determined by writing a value of
* 0xffffffff to the register, and reading it back. Only
* 1 bits are decoded.
*/
#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */
#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */
#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */
#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */
#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */
#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */
#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */
#define PCI_BASE_ADDRESS_SPACE_IO 0x01
#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */
#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */
#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */
#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */
#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL)
/* bit 1 is reserved if address_space = 1 */
/* Header type 0 (normal devices) */
#define PCI_CARDBUS_CIS 0x28
#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
#define PCI_SUBSYSTEM_ID 0x2e
#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */
#define PCI_ROM_ADDRESS_ENABLE 0x01
#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */
/* 0x35-0x3b are reserved */
#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */
#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */
#define PCI_MIN_GNT 0x3e /* 8 bits */
#define PCI_MAX_LAT 0x3f /* 8 bits */
/* Header type 1 (PCI-to-PCI bridges) */
#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */
#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */
#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */
#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */
#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */
#define PCI_IO_LIMIT 0x1d
#define PCI_IO_RANGE_TYPE_MASK 0x0fUL /* I/O bridging type */
#define PCI_IO_RANGE_TYPE_16 0x00
#define PCI_IO_RANGE_TYPE_32 0x01
#define PCI_IO_RANGE_MASK (~0x0fUL)
#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */
#define PCI_MEMORY_BASE 0x20 /* Memory range behind */
#define PCI_MEMORY_LIMIT 0x22
#define PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL
#define PCI_MEMORY_RANGE_MASK (~0x0fUL)
#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */
#define PCI_PREF_MEMORY_LIMIT 0x26
#define PCI_PREF_RANGE_TYPE_MASK 0x0fUL
#define PCI_PREF_RANGE_TYPE_32 0x00
#define PCI_PREF_RANGE_TYPE_64 0x01
#define PCI_PREF_RANGE_MASK (~0x0fUL)
#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */
#define PCI_PREF_LIMIT_UPPER32 0x2c
#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */
#define PCI_IO_LIMIT_UPPER16 0x32
/* 0x34 same as for htype 0 */
/* 0x35-0x3b is reserved */
#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */
/* 0x3c-0x3d are same as for htype 0 */
#define PCI_BRIDGE_CONTROL 0x3e
#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */
#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */
#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */
#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */
#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */
#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */
#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */
/* Header type 2 (CardBus bridges) */
#define PCI_CB_CAPABILITY_LIST 0x14
/* 0x15 reserved */
#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */
#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */
#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */
#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */
#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */
#define PCI_CB_MEMORY_BASE_0 0x1c
#define PCI_CB_MEMORY_LIMIT_0 0x20
#define PCI_CB_MEMORY_BASE_1 0x24
#define PCI_CB_MEMORY_LIMIT_1 0x28
#define PCI_CB_IO_BASE_0 0x2c
#define PCI_CB_IO_BASE_0_HI 0x2e
#define PCI_CB_IO_LIMIT_0 0x30
#define PCI_CB_IO_LIMIT_0_HI 0x32
#define PCI_CB_IO_BASE_1 0x34
#define PCI_CB_IO_BASE_1_HI 0x36
#define PCI_CB_IO_LIMIT_1 0x38
#define PCI_CB_IO_LIMIT_1_HI 0x3a
#define PCI_CB_IO_RANGE_MASK (~0x03UL)
/* 0x3c-0x3d are same as for htype 0 */
#define PCI_CB_BRIDGE_CONTROL 0x3e
#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */
#define PCI_CB_BRIDGE_CTL_SERR 0x02
#define PCI_CB_BRIDGE_CTL_ISA 0x04
#define PCI_CB_BRIDGE_CTL_VGA 0x08
#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20
#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */
#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */
#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */
#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400
#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
#define PCI_CB_SUBSYSTEM_ID 0x42
#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */
/* 0x48-0x7f reserved */
/* Capability lists */
#define PCI_CAP_LIST_ID 0 /* Capability ID */
#define PCI_CAP_ID_PM 0x01 /* Power Management */
#define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */
#define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */
#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */
#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */
#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */
#define PCI_CAP_ID_PCIX 0x07 /* PCI-X */
#define PCI_CAP_ID_HT 0x08 /* HyperTransport */
#define PCI_CAP_ID_VNDR 0x09 /* Vendor specific capability */
#define PCI_CAP_ID_SHPC 0x0C /* PCI Standard Hot-Plug Controller */
#define PCI_CAP_ID_EXP 0x10 /* PCI Express */
#define PCI_CAP_ID_MSIX 0x11 /* MSI-X */
#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */
#define PCI_CAP_SIZEOF 4
/* Power Management Registers */
#define PCI_PM_PMC 2 /* PM Capabilities Register */
#define PCI_PM_CAP_VER_MASK 0x0007 /* Version */
#define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */
#define PCI_PM_CAP_RESERVED 0x0010 /* Reserved field */
#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */
#define PCI_PM_CAP_AUX_POWER 0x01C0 /* Auxilliary power support mask */
#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */
#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */
#define PCI_PM_CAP_PME 0x0800 /* PME pin supported */
#define PCI_PM_CAP_PME_MASK 0xF800 /* PME Mask of all supported states */
#define PCI_PM_CAP_PME_D0 0x0800 /* PME# from D0 */
#define PCI_PM_CAP_PME_D1 0x1000 /* PME# from D1 */
#define PCI_PM_CAP_PME_D2 0x2000 /* PME# from D2 */
#define PCI_PM_CAP_PME_D3 0x4000 /* PME# from D3 (hot) */
#define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */
#define PCI_PM_CTRL 4 /* PM control and status register */
#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */
#define PCI_PM_CTRL_NO_SOFT_RESET 0x0004 /* No reset for D3hot->D0 */
#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */
#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */
#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */
#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */
#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */
#define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */
#define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */
#define PCI_PM_DATA_REGISTER 7 /* (??) */
#define PCI_PM_SIZEOF 8
/* AGP registers */
#define PCI_AGP_VERSION 2 /* BCD version number */
#define PCI_AGP_RFU 3 /* Rest of capability flags */
#define PCI_AGP_STATUS 4 /* Status register */
#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */
#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */
#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */
#define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */
#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */
#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */
#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */
#define PCI_AGP_COMMAND 8 /* Control register */
#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */
#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */
#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */
#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */
#define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */
#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */
#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate */
#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate */
#define PCI_AGP_SIZEOF 12
/* Vital Product Data */
#define PCI_VPD_ADDR 2 /* Address to access (15 bits!) */
#define PCI_VPD_ADDR_MASK 0x7fff /* Address mask */
#define PCI_VPD_ADDR_F 0x8000 /* Write 0, 1 indicates completion */
#define PCI_VPD_DATA 4 /* 32-bits of data returned here */
/* Slot Identification */
#define PCI_SID_ESR 2 /* Expansion Slot Register */
#define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */
#define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */
#define PCI_SID_CHASSIS_NR 3 /* Chassis Number */
/* Message Signalled Interrupts registers */
#define PCI_MSI_FLAGS 2 /* Various flags */
#define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */
#define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */
#define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */
#define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */
#define PCI_MSI_FLAGS_MASKBIT 0x100 /* 64-bit mask bits allowed */
#define PCI_MSI_RFU 3 /* Rest of capability flags */
#define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */
#define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */
#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */
#define PCI_MSI_MASK_BIT 16 /* Mask bits register */
/* MSI-X registers (these are at offset PCI_MSIX_FLAGS) */
#define PCI_MSIX_FLAGS 2
#define PCI_MSIX_FLAGS_QSIZE 0x7FF
#define PCI_MSIX_FLAGS_ENABLE (1 << 15)
#define PCI_MSIX_FLAGS_MASKALL (1 << 14)
#define PCI_MSIX_FLAGS_BIRMASK (7 << 0)
#define PCI_MSIX_FLAGS_BITMASK (1 << 0)
/* CompactPCI Hotswap Register */
#define PCI_CHSWP_CSR 2 /* Control and Status Register */
#define PCI_CHSWP_DHA 0x01 /* Device Hiding Arm */
#define PCI_CHSWP_EIM 0x02 /* ENUM# Signal Mask */
#define PCI_CHSWP_PIE 0x04 /* Pending Insert or Extract */
#define PCI_CHSWP_LOO 0x08 /* LED On / Off */
#define PCI_CHSWP_PI 0x30 /* Programming Interface */
#define PCI_CHSWP_EXT 0x40 /* ENUM# status - extraction */
#define PCI_CHSWP_INS 0x80 /* ENUM# status - insertion */
/* PCI-X registers */
#define PCI_X_CMD 2 /* Modes & Features */
#define PCI_X_CMD_DPERR_E 0x0001 /* Data Parity Error Recovery Enable */
#define PCI_X_CMD_ERO 0x0002 /* Enable Relaxed Ordering */
#define PCI_X_CMD_READ_512 0x0000 /* 512 byte maximum read byte count */
#define PCI_X_CMD_READ_1K 0x0004 /* 1Kbyte maximum read byte count */
#define PCI_X_CMD_READ_2K 0x0008 /* 2Kbyte maximum read byte count */
#define PCI_X_CMD_READ_4K 0x000c /* 4Kbyte maximum read byte count */
#define PCI_X_CMD_MAX_READ 0x000c /* Max Memory Read Byte Count */
/* Max # of outstanding split transactions */
#define PCI_X_CMD_SPLIT_1 0x0000 /* Max 1 */
#define PCI_X_CMD_SPLIT_2 0x0010 /* Max 2 */
#define PCI_X_CMD_SPLIT_3 0x0020 /* Max 3 */
#define PCI_X_CMD_SPLIT_4 0x0030 /* Max 4 */
#define PCI_X_CMD_SPLIT_8 0x0040 /* Max 8 */
#define PCI_X_CMD_SPLIT_12 0x0050 /* Max 12 */
#define PCI_X_CMD_SPLIT_16 0x0060 /* Max 16 */
#define PCI_X_CMD_SPLIT_32 0x0070 /* Max 32 */
#define PCI_X_CMD_MAX_SPLIT 0x0070 /* Max Outstanding Split Transactions */
#define PCI_X_CMD_VERSION(x) (((x) >> 12) & 3) /* Version */
#define PCI_X_STATUS 4 /* PCI-X capabilities */
#define PCI_X_STATUS_DEVFN 0x000000ff /* A copy of devfn */
#define PCI_X_STATUS_BUS 0x0000ff00 /* A copy of bus nr */
#define PCI_X_STATUS_64BIT 0x00010000 /* 64-bit device */
#define PCI_X_STATUS_133MHZ 0x00020000 /* 133 MHz capable */
#define PCI_X_STATUS_SPL_DISC 0x00040000 /* Split Completion Discarded */
#define PCI_X_STATUS_UNX_SPL 0x00080000 /* Unexpected Split Completion */
#define PCI_X_STATUS_COMPLEX 0x00100000 /* Device Complexity */
#define PCI_X_STATUS_MAX_READ 0x00600000 /* Designed Max Memory Read Count */
#define PCI_X_STATUS_MAX_SPLIT 0x03800000 /* Designed Max Outstanding Split Transactions */
#define PCI_X_STATUS_MAX_CUM 0x1c000000 /* Designed Max Cumulative Read Size */
#define PCI_X_STATUS_SPL_ERR 0x20000000 /* Rcvd Split Completion Error Msg */
#define PCI_X_STATUS_266MHZ 0x40000000 /* 266 MHz capable */
#define PCI_X_STATUS_533MHZ 0x80000000 /* 533 MHz capable */
/* PCI Express capability registers */
#define PCI_EXP_FLAGS 2 /* Capabilities register */
#define PCI_EXP_FLAGS_VERS 0x000f /* Capability version */
#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */
#define PCI_EXP_TYPE_ENDPOINT 0x0 /* Express Endpoint */
#define PCI_EXP_TYPE_LEG_END 0x1 /* Legacy Endpoint */
#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */
#define PCI_EXP_TYPE_UPSTREAM 0x5 /* Upstream Port */
#define PCI_EXP_TYPE_DOWNSTREAM 0x6 /* Downstream Port */
#define PCI_EXP_TYPE_PCI_BRIDGE 0x7 /* PCI/PCI-X Bridge */
#define PCI_EXP_FLAGS_SLOT 0x0100 /* Slot implemented */
#define PCI_EXP_FLAGS_IRQ 0x3e00 /* Interrupt message number */
#define PCI_EXP_DEVCAP 4 /* Device capabilities */
#define PCI_EXP_DEVCAP_PAYLOAD 0x07 /* Max_Payload_Size */
#define PCI_EXP_DEVCAP_PHANTOM 0x18 /* Phantom functions */
#define PCI_EXP_DEVCAP_EXT_TAG 0x20 /* Extended tags */
#define PCI_EXP_DEVCAP_L0S 0x1c0 /* L0s Acceptable Latency */
#define PCI_EXP_DEVCAP_L1 0xe00 /* L1 Acceptable Latency */
#define PCI_EXP_DEVCAP_ATN_BUT 0x1000 /* Attention Button Present */
#define PCI_EXP_DEVCAP_ATN_IND 0x2000 /* Attention Indicator Present */
#define PCI_EXP_DEVCAP_PWR_IND 0x4000 /* Power Indicator Present */
#define PCI_EXP_DEVCAP_PWR_VAL 0x3fc0000 /* Slot Power Limit Value */
#define PCI_EXP_DEVCAP_PWR_SCL 0xc000000 /* Slot Power Limit Scale */
#define PCI_EXP_DEVCTL 8 /* Device Control */
#define PCI_EXP_DEVCTL_CERE 0x0001 /* Correctable Error Reporting En. */
#define PCI_EXP_DEVCTL_NFERE 0x0002 /* Non-Fatal Error Reporting Enable */
#define PCI_EXP_DEVCTL_FERE 0x0004 /* Fatal Error Reporting Enable */
#define PCI_EXP_DEVCTL_URRE 0x0008 /* Unsupported Request Reporting En. */
#define PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
#define PCI_EXP_DEVCTL_PAYLOAD 0x00e0 /* Max_Payload_Size */
#define PCI_EXP_DEVCTL_EXT_TAG 0x0100 /* Extended Tag Field Enable */
#define PCI_EXP_DEVCTL_PHANTOM 0x0200 /* Phantom Functions Enable */
#define PCI_EXP_DEVCTL_AUX_PME 0x0400 /* Auxiliary Power PM Enable */
#define PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800 /* Enable No Snoop */
#define PCI_EXP_DEVCTL_READRQ 0x7000 /* Max_Read_Request_Size */
#define PCI_EXP_DEVSTA 10 /* Device Status */
#define PCI_EXP_DEVSTA_CED 0x01 /* Correctable Error Detected */
#define PCI_EXP_DEVSTA_NFED 0x02 /* Non-Fatal Error Detected */
#define PCI_EXP_DEVSTA_FED 0x04 /* Fatal Error Detected */
#define PCI_EXP_DEVSTA_URD 0x08 /* Unsupported Request Detected */
#define PCI_EXP_DEVSTA_AUXPD 0x10 /* AUX Power Detected */
#define PCI_EXP_DEVSTA_TRPND 0x20 /* Transactions Pending */
#define PCI_EXP_LNKCAP 12 /* Link Capabilities */
#define PCI_EXP_LNKCTL 16 /* Link Control */
#define PCI_EXP_LNKCTL_CLKREQ_EN 0x100 /* Enable clkreq */
#define PCI_EXP_LNKSTA 18 /* Link Status */
#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */
#define PCI_EXP_SLTCTL 24 /* Slot Control */
#define PCI_EXP_SLTSTA 26 /* Slot Status */
#define PCI_EXP_RTCTL 28 /* Root Control */
#define PCI_EXP_RTCTL_SECEE 0x01 /* System Error on Correctable Error */
#define PCI_EXP_RTCTL_SENFEE 0x02 /* System Error on Non-Fatal Error */
#define PCI_EXP_RTCTL_SEFEE 0x04 /* System Error on Fatal Error */
#define PCI_EXP_RTCTL_PMEIE 0x08 /* PME Interrupt Enable */
#define PCI_EXP_RTCTL_CRSSVE 0x10 /* CRS Software Visibility Enable */
#define PCI_EXP_RTCAP 30 /* Root Capabilities */
#define PCI_EXP_RTSTA 32 /* Root Status */
/* Extended Capabilities (PCI-X 2.0 and Express) */
#define PCI_EXT_CAP_ID(header) (header & 0x0000ffff)
#define PCI_EXT_CAP_VER(header) ((header >> 16) & 0xf)
#define PCI_EXT_CAP_NEXT(header) ((header >> 20) & 0xffc)
#define PCI_EXT_CAP_ID_ERR 1
#define PCI_EXT_CAP_ID_VC 2
#define PCI_EXT_CAP_ID_DSN 3
#define PCI_EXT_CAP_ID_PWR 4
/* Advanced Error Reporting */
#define PCI_ERR_UNCOR_STATUS 4 /* Uncorrectable Error Status */
#define PCI_ERR_UNC_TRAIN 0x00000001 /* Training */
#define PCI_ERR_UNC_DLP 0x00000010 /* Data Link Protocol */
#define PCI_ERR_UNC_POISON_TLP 0x00001000 /* Poisoned TLP */
#define PCI_ERR_UNC_FCP 0x00002000 /* Flow Control Protocol */
#define PCI_ERR_UNC_COMP_TIME 0x00004000 /* Completion Timeout */
#define PCI_ERR_UNC_COMP_ABORT 0x00008000 /* Completer Abort */
#define PCI_ERR_UNC_UNX_COMP 0x00010000 /* Unexpected Completion */
#define PCI_ERR_UNC_RX_OVER 0x00020000 /* Receiver Overflow */
#define PCI_ERR_UNC_MALF_TLP 0x00040000 /* Malformed TLP */
#define PCI_ERR_UNC_ECRC 0x00080000 /* ECRC Error Status */
#define PCI_ERR_UNC_UNSUP 0x00100000 /* Unsupported Request */
#define PCI_ERR_UNCOR_MASK 8 /* Uncorrectable Error Mask */
/* Same bits as above */
#define PCI_ERR_UNCOR_SEVER 12 /* Uncorrectable Error Severity */
/* Same bits as above */
#define PCI_ERR_COR_STATUS 16 /* Correctable Error Status */
#define PCI_ERR_COR_RCVR 0x00000001 /* Receiver Error Status */
#define PCI_ERR_COR_BAD_TLP 0x00000040 /* Bad TLP Status */
#define PCI_ERR_COR_BAD_DLLP 0x00000080 /* Bad DLLP Status */
#define PCI_ERR_COR_REP_ROLL 0x00000100 /* REPLAY_NUM Rollover */
#define PCI_ERR_COR_REP_TIMER 0x00001000 /* Replay Timer Timeout */
#define PCI_ERR_COR_MASK 20 /* Correctable Error Mask */
/* Same bits as above */
#define PCI_ERR_CAP 24 /* Advanced Error Capabilities */
#define PCI_ERR_CAP_FEP(x) ((x) & 31) /* First Error Pointer */
#define PCI_ERR_CAP_ECRC_GENC 0x00000020 /* ECRC Generation Capable */
#define PCI_ERR_CAP_ECRC_GENE 0x00000040 /* ECRC Generation Enable */
#define PCI_ERR_CAP_ECRC_CHKC 0x00000080 /* ECRC Check Capable */
#define PCI_ERR_CAP_ECRC_CHKE 0x00000100 /* ECRC Check Enable */
#define PCI_ERR_HEADER_LOG 28 /* Header Log Register (16 bytes) */
#define PCI_ERR_ROOT_COMMAND 44 /* Root Error Command */
/* Correctable Err Reporting Enable */
#define PCI_ERR_ROOT_CMD_COR_EN 0x00000001
/* Non-fatal Err Reporting Enable */
#define PCI_ERR_ROOT_CMD_NONFATAL_EN 0x00000002
/* Fatal Err Reporting Enable */
#define PCI_ERR_ROOT_CMD_FATAL_EN 0x00000004
#define PCI_ERR_ROOT_STATUS 48
#define PCI_ERR_ROOT_COR_RCV 0x00000001 /* ERR_COR Received */
/* Multi ERR_COR Received */
#define PCI_ERR_ROOT_MULTI_COR_RCV 0x00000002
/* ERR_FATAL/NONFATAL Recevied */
#define PCI_ERR_ROOT_UNCOR_RCV 0x00000004
/* Multi ERR_FATAL/NONFATAL Recevied */
#define PCI_ERR_ROOT_MULTI_UNCOR_RCV 0x00000008
#define PCI_ERR_ROOT_FIRST_FATAL 0x00000010 /* First Fatal */
#define PCI_ERR_ROOT_NONFATAL_RCV 0x00000020 /* Non-Fatal Received */
#define PCI_ERR_ROOT_FATAL_RCV 0x00000040 /* Fatal Received */
#define PCI_ERR_ROOT_COR_SRC 52
#define PCI_ERR_ROOT_SRC 54
/* Virtual Channel */
#define PCI_VC_PORT_REG1 4
#define PCI_VC_PORT_REG2 8
#define PCI_VC_PORT_CTRL 12
#define PCI_VC_PORT_STATUS 14
#define PCI_VC_RES_CAP 16
#define PCI_VC_RES_CTRL 20
#define PCI_VC_RES_STATUS 26
/* Power Budgeting */
#define PCI_PWR_DSR 4 /* Data Select Register */
#define PCI_PWR_DATA 8 /* Data Register */
#define PCI_PWR_DATA_BASE(x) ((x) & 0xff) /* Base Power */
#define PCI_PWR_DATA_SCALE(x) (((x) >> 8) & 3) /* Data Scale */
#define PCI_PWR_DATA_PM_SUB(x) (((x) >> 10) & 7) /* PM Sub State */
#define PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */
#define PCI_PWR_DATA_TYPE(x) (((x) >> 15) & 7) /* Type */
#define PCI_PWR_DATA_RAIL(x) (((x) >> 18) & 7) /* Power Rail */
#define PCI_PWR_CAP 12 /* Capability */
#define PCI_PWR_CAP_BUDGET(x) ((x) & 1) /* Included in system budget */
/*
* Hypertransport sub capability types
*
* Unfortunately there are both 3 bit and 5 bit capability types defined
* in the HT spec, catering for that is a little messy. You probably don't
* want to use these directly, just use pci_find_ht_capability() and it
* will do the right thing for you.
*/
#define HT_3BIT_CAP_MASK 0xE0
#define HT_CAPTYPE_SLAVE 0x00 /* Slave/Primary link configuration */
#define HT_CAPTYPE_HOST 0x20 /* Host/Secondary link configuration */
#define HT_5BIT_CAP_MASK 0xF8
#define HT_CAPTYPE_IRQ 0x80 /* IRQ Configuration */
#define HT_CAPTYPE_REMAPPING_40 0xA0 /* 40 bit address remapping */
#define HT_CAPTYPE_REMAPPING_64 0xA2 /* 64 bit address remapping */
#define HT_CAPTYPE_UNITID_CLUMP 0x90 /* Unit ID clumping */
#define HT_CAPTYPE_EXTCONF 0x98 /* Extended Configuration Space Access */
#define HT_CAPTYPE_MSI_MAPPING 0xA8 /* MSI Mapping Capability */
#define HT_MSI_FLAGS 0x02 /* Offset to flags */
#define HT_MSI_FLAGS_ENABLE 0x1 /* Mapping enable */
#define HT_MSI_FLAGS_FIXED 0x2 /* Fixed mapping only */
#define HT_MSI_FIXED_ADDR 0x00000000FEE00000ULL /* Fixed addr */
#define HT_MSI_ADDR_LO 0x04 /* Offset to low addr bits */
#define HT_MSI_ADDR_LO_MASK 0xFFF00000 /* Low address bit mask */
#define HT_MSI_ADDR_HI 0x08 /* Offset to high addr bits */
#define HT_CAPTYPE_DIRECT_ROUTE 0xB0 /* Direct routing configuration */
#define HT_CAPTYPE_VCSET 0xB8 /* Virtual Channel configuration */
#define HT_CAPTYPE_ERROR_RETRY 0xC0 /* Retry on error configuration */
#define HT_CAPTYPE_GEN3 0xD0 /* Generation 3 hypertransport configuration */
#define HT_CAPTYPE_PM 0xE0 /* Hypertransport powermanagement configuration */
#endif /* LINUX_PCI_REGS_H */
|
