/*
* Definitions for the FTDI USB Single Port Serial Converter -
* known as FTDI_SIO (Serial Input/Output application of the chipset)
*
* The example I have is known as the USC-1000 which is available from
* http://www.dse.co.nz - cat no XH4214 It looks similar to this:
* http://www.dansdata.com/usbser.htm but I can't be sure There are other
* USC-1000s which don't look like my device though so beware!
*
* The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
* USB on the other.
*
* Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
* of the protocol required to talk to the device and ongoing assistence
* during development.
*
* Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the
* FTDI_SIO implementation.
*
* Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
* from Rudolf Gugler
*
*/
#define FTDI_VID 0x0403 /* Vendor Id */
#define FTDI_SIO_PID 0x8372 /* Product Id SIO application of 8U100AX */
#define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
#define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
#define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
#define FTDI_232RL_PID 0xFBFA /* Product ID for FT232RL */
#define FTDI_RELAIS_PID 0xFA10 /* Relais device from Rudolf Gugler */
#define FTDI_NF_RIC_VID 0x0DCD /* Vendor Id */
#define FTDI_NF_RIC_PID 0x0001 /* Product Id */
#define FTDI_USBX_707_PID 0xF857 /* ADSTech IR Blaster USBX-707 */
/* www.canusb.com Lawicel CANUSB device */
#define FTDI_CANUSB_PID 0xFFA8 /* Product Id */
/* AlphaMicro Components AMC-232USB01 device */
#define FTDI_AMC232_PID 0xFF00 /* Product Id */
/* SCS HF Radio Modems PID's (http://www.scs-ptc.com) */
/* the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_SCS_DEVICE_0_PID 0xD010 /* SCS PTC-IIusb */
#define FTDI_SCS_DEVICE_1_PID 0xD011 /* SCS Tracker / DSP TNC */
#define FTDI_SCS_DEVICE_2_PID 0xD012
#define FTDI_SCS_DEVICE_3_PID 0xD013
#define FTDI_SCS_DEVICE_4_PID 0xD014
#define FTDI_SCS_DEVICE_5_PID 0xD015
#define FTDI_SCS_DEVICE_6_PID 0xD016
#define FTDI_SCS_DEVICE_7_PID 0xD017
/* ACT Solutions HomePro ZWave interface (http://www.act-solutions.com/HomePro.htm) */
#define FTDI_ACTZWAVE_PID 0xF2D0
/* www.starting-point-systems.com µChameleon device */
#define FTDI_MICRO_CHAMELEON_PID 0xCAA0 /* Product Id */
/* www.irtrans.de device */
#define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
/* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
#define FTDI_TTUSB_PID 0xFF20 /* Product Id */
/* iPlus device */
#define FTDI_IPLUS_PID 0xD070 /* Product Id */
#define FTDI_IPLUS2_PID 0xD071 /* Product Id */
/* DMX4ALL DMX Interfaces */
#define FTDI_DMX4ALL 0xC850
/* OpenDCC (www.opendcc.de) product id */
#define FTDI_OPENDCC_PID 0xBFD8
/* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
/* they use the ftdi chipset for the USB interface and the vendor id is the same */
#define FTDI_XF_632_PID 0xFC08 /* 632: 16x2 Character Display */
#define FTDI_XF_634_PID 0xFC09 /* 634: 20x4 Character Display */
#define FTDI_XF_547_PID 0xFC0A /* 547: Two line Display */
#define FTDI_XF_633_PID 0xFC0B /* 633: 16x2 Character Display with Keys */
#define FTDI_XF_631_PID 0xFC0C /* 631: 20x2 Character Display */
#define FTDI_XF_635_PID 0xFC0D /* 635: 20x4 Character Display */
#define FTDI_XF_640_PID 0xFC0E /* 640: Two line Display */
#define FTDI_XF_642_PID 0xFC0F /* 642: Two line Display */
/* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
/* broadband internet service. The following PID is exhibited by the usb device supplied */
/* (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */
/*
* PCDJ use ftdi based dj-controllers. The following PID is for their DAC-2 device
* http://www.pcdjhardware.com/DAC2.asp (PID sent by Wouter Paesen)
* (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_PCDJ_DAC2_PID 0xFA88
/*
* The following are the values for the Matrix Orbital LCD displays,
* which are the FT232BM ( similar to the 8U232AM )
*/
#define FTDI_MTXORB_0_PID 0xFA00 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_1_PID 0xFA01 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_2_PID 0xFA02 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_3_PID 0xFA03 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_4_PID 0xFA04 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_5_PID 0xFA05 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_6_PID 0xFA06 /* Matrix Orbital Product Id */
/* OOCDlink by Joern Kaipf <joernk@web.de>
* (http://www.joernonline.de/dw/doku.php?id=start&idx=projects:oocdlink) */
#define FTDI_OOCDLINK_PID 0xbaf8 /* Amontec JTAGkey */
/*
* The following are the values for the Matrix Orbital FTDI Range
* Anything in this range will use an FT232RL.
*/
#define MTXORB_VID 0x1B3D
#define MTXORB_FTDI_RANGE_0100_PID 0x0100
#define MTXORB_FTDI_RANGE_0101_PID 0x0101
#define MTXORB_FTDI_RANGE_0102_PID 0x0102
#define MTXORB_FTDI_RANGE_0103_PID 0x0103
#define MTXORB_FTDI_RANGE_0104_PID 0x0104
#define MTXORB_FTDI_RANGE_0105_PID 0x0105
#define MTXORB_FTDI_RANGE_0106_PID 0x0106
#define MTXORB_FTDI_RANGE_0107_PID 0x0107
#define MTXORB_FTDI_RANGE_0108_PID 0x0108
#define MTXORB_FTDI_RANGE_0109_PID 0x0109
#define MTXORB_FTDI_RANGE_010A_PID 0x010A
#define MTXORB_FTDI_RANGE_010B_PID 0x010B
#define MTXORB_FTDI_RANGE_010C_PID 0x010C
#define MTXORB_FTDI_RANGE_010D_PID 0x010D
#define MTXORB_FTDI_RANGE_010E_PID 0x010E
#define MTXORB_FTDI_RANGE_010F_PID 0x010F
#define MTXORB_FTDI_RANGE_0110_PID 0x0110
#define MTXORB_FTDI_RANGE_0111_PID 0x0111
#define MTXORB_FTDI_RANGE_0112_PID 0x0112
#define MTXORB_FTDI_RANGE_0113_PID 0x0113
#define MTXORB_FTDI_RANGE_0114_PID 0x0114
#define MTXORB_FTDI_RANGE_0115_PID 0x0115
#define MTXORB_FTDI_RANGE_0116_PID 0x0116
#define MTXORB_FTDI_RANGE_0117_PID 0x0117
#define MTXORB_FTDI_RANGE_0118_PID 0x0118
#define MTXORB_FTDI_RANGE_0119_PID 0x0119
#define MTXORB_FTDI_RANGE_011A_PID 0x011A
#define MTXORB_FTDI_RANGE_011B_PID 0x011B
#define MTXORB_FTDI_RANGE_011C_PID 0x011C
#define MTXORB_FTDI_RANGE_011D_PID 0x011D
#define MTXORB_FTDI_RANGE_011E_PID 0x011E
#define MTXORB_FTDI_RANGE_011F_PID 0x011F
#define MTXORB_FTDI_RANGE_0120_PID 0x0120
#define MTXORB_FTDI_RANGE_0121_PID 0x0121
#define MTXORB_FTDI_RANGE_0122_PID 0x0122
#define MTXORB_FTDI_RANGE_0123_PID 0x0123
#define MTXORB_FTDI_RANGE_0124_PID 0x0124
#define MTXORB_FTDI_RANGE_0125_PID 0x0125
#define MTXORB_FTDI_RANGE_0126_PID 0x0126
#define MTXORB_FTDI_RANGE_0127_PID 0x0127
#define MTXORB_FTDI_RANGE_0128_PID 0x0128
#define MTXORB_FTDI_RANGE_0129_PID 0x0129
#define MTXORB_FTDI_RANGE_012A_PID 0x012A
#define MTXORB_FTDI_RANGE_012B_PID 0x012B
#define MTXORB_FTDI_RANGE_012C_PID 0x012C
#define MTXORB_FTDI_RANGE_012D_PID 0x012D
#define MTXORB_FTDI_RANGE_012E_PID 0x012E
#define MTXORB_FTDI_RANGE_012F_PID 0x012F
#define MTXORB_FTDI_RANGE_0130_PID 0x0130
#define MTXORB_FTDI_RANGE_0131_PID 0x0131
#define MTXORB_FTDI_RANGE_0132_PID 0x0132
#define MTXORB_FTDI_RANGE_0133_PID 0x0133
#define MTXORB_FTDI_RANGE_0134_PID 0x0134
#define MTXORB_FTDI_RANGE_0135_PID 0x0135
#define MTXORB_FTDI_RANGE_0136_PID 0x0136
#define MTXORB_FTDI_RANGE_0137_PID 0x0137
#define MTXORB_FTDI_RANGE_0138_PID 0x0138
#define MTXORB_FTDI_RANGE_0139_PID 0x0139
#define MTXORB_FTDI_RANGE_013A_PID 0x013A
#define MTXORB_FTDI_RANGE_013B_PID 0x013B
#define MTXORB_FTDI_RANGE_013C_PID 0x013C
#define MTXORB_FTDI_RANGE_013D_PID 0x013D
#define MTXORB_FTDI_RANGE_013E_PID 0x013E
#define MTXORB_FTDI_RANGE_013F_PID 0x013F
#define MTXORB_FTDI_RANGE_0140_PID 0x0140
#define MTXORB_FTDI_RANGE_0141_PID 0x0141
#define MTXORB_FTDI_RANGE_0142_PID 0x0142
#define MTXORB_FTDI_RANGE_0143_PID 0x0143
#define MTXORB_FTDI_RANGE_0144_PID 0x0144
#define MTXORB_FTDI_RANGE_0145_PID 0x0145
#define MTXORB_FTDI_RANGE_0146_PID 0x0146
#define MTXORB_FTDI_RANGE_0147_PID 0x0147
#define MTXORB_FTDI_RANGE_0148_PID 0x0148
#define MTXORB_FTDI_RANGE_0149_PID 0x0149
#define MTXORB_FTDI_RANGE_014A_PID 0x014A
#define MTXORB_FTDI_RANGE_014B_PID 0x014B
#define MTXORB_FTDI_RANGE_014C_PID 0x014C
#define MTXORB_FTDI_RANGE_014D_PID 0x014D
#define MTXORB_FTDI_RANGE_014E_PID 0x014E
#define MTXORB_FTDI_RANGE_014F_PID 0x014F
#define MTXORB_FTDI_RANGE_0150_PID 0x0150
#define MTXORB_FTDI_RANGE_0151_PID 0x0151
#define MTXORB_FTDI_RANGE_0152_PID 0x0152
#define MTXORB_FTDI_RANGE_0153_PID 0x0153
#define MTXORB_FTDI_RANGE_0154_PID 0x0154
#define MTXORB_FTDI_RANGE_0155_PID 0x0155
#define MTXORB_FTDI_RANGE_0156_PID 0x0156
#define MTXORB_FTDI_RANGE_0157_PID 0x0157
#define MTXORB_FTDI_RANGE_0158_PID 0x0158
#define MTXORB_FTDI_RANGE_0159_PID 0x0159
#define MTXORB_FTDI_RANGE_015A_PID 0x015A
#define MTXORB_FTDI_RANGE_015B_PID 0x015B
#define MTXORB_FTDI_RANGE_015C_PID 0x015C
#define MTXORB_FTDI_RANGE_015D_PID 0x015D
#define MTXORB_FTDI_RANGE_015E_PID 0x015E
#define MTXORB_FTDI_RANGE_015F_PID 0x015F
#define MTXORB_FTDI_RANGE_0160_PID 0x0160
#define MTXORB_FTDI_RANGE_0161_PID 0x0161
#define MTXORB_FTDI_RANGE_0162_PID 0x0162
#define MTXORB_FTDI_RANGE_0163_PID 0x0163
#define MTXORB_FTDI_RANGE_0164_PID 0x0164
#define MTXORB_FTDI_RANGE_0165_PID 0x0165
#define MTXORB_FTDI_RANGE_0166_PID 0x0166
#define MTXORB_FTDI_RANGE_0167_PID 0x0167
#define MTXORB_FTDI_RANGE_0168_PID 0x0168
#define MTXORB_FTDI_RANGE_0169_PID 0x0169
#define MTXORB_FTDI_RANGE_016A_PID 0x016A
#define MTXORB_FTDI_RANGE_016B_PID 0x016B
#define MTXORB_FTDI_RANGE_016C_PID 0x016C
#define MTXORB_FTDI_RANGE_016D_PID 0x016D
#define MTXORB_FTDI_RANGE_016E_PID 0x016E
#define MTXORB_FTDI_RANGE_016F_PID 0x016F
#define MTXORB_FTDI_RANGE_0170_PID 0x0170
#define MTXORB_FTDI_RANGE_0171_PID 0x0171
#define MTXORB_FTDI_RANGE_0172_PID 0x0172
#define MTXORB_FTDI_RANGE_0173_PID 0x0173
#define MTXORB_FTDI_RANGE_0174_PID 0x0174
#define MTXORB_FTDI_RANGE_0175_PID 0x0175
#define MTXORB_FTDI_RANGE_0176_PID 0x0176
#define MTXORB_FTDI_RANGE_0177_PID 0x0177
#define MTXORB_FTDI_RANGE_0178_PID 0x0178
#define MTXORB_FTDI_RANGE_0179_PID 0x0179
#define MTXORB_FTDI_RANGE_017A_PID 0x017A
#define MTXORB_FTDI_RANGE_017B_PID 0x017B
#define MTXORB_FTDI_RANGE_017C_PID 0x017C
#define MTXORB_FTDI_RANGE_017D_PID 0x017D
#define MTXORB_FTDI_RANGE_017E_PID 0x017E
#define MTXORB_FTDI_RANGE_017F_PID 0x017F
#define MTXORB_FTDI_RANGE_0180_PID 0x0180
#define MTXORB_FTDI_RANGE_0181_PID 0x0181
#define MTXORB_FTDI_RANGE_0182_PID 0x0182
#define MTXORB_FTDI_RANGE_0183_PID 0x0183
#define MTXORB_FTDI_RANGE_0184_PID 0x0184
#define MTXORB_FTDI_RANGE_0185_PID 0x0185
#define MTXORB_FTDI_RANGE_0186_PID 0x0186
#define MTXORB_FTDI_RANGE_0187_PID 0x0187
#define MTXORB_FTDI_RANGE_0188_PID 0x0188
#define MTXORB_FTDI_RANGE_0189_PID 0x0189
#define MTXORB_FTDI_RANGE_018A_PID 0x018A
#define MTXORB_FTDI_RANGE_018B_PID 0x018B
#define MTXORB_FTDI_RANGE_018C_PID 0x018C
#define MTXORB_FTDI_RANGE_018D_PID 0x018D
#define MTXORB_FTDI_RANGE_018E_PID 0x018E
#define MTXORB_FTDI_RANGE_018F_PID 0x018F
#define MTXORB_FTDI_RANGE_0190_PID 0x0190
#define MTXORB_FTDI_RANGE_0191_PID 0x0191
#define MTXORB_FTDI_RANGE_0192_PID 0x0192
#define MTXORB_FTDI_RANGE_0193_PID 0x0193
#define MTXORB_FTDI_RANGE_0194_PID 0x0194
#define MTXORB_FTDI_RANGE_0195_PID 0x0195
#define MTXORB_FTDI_RANGE_0196_PID 0x0196
#define MTXORB_FTDI_RANGE_0197_PID 0x0197
#define MTXORB_FTDI_RANGE_0198_PID 0x0198
#define MTXORB_FTDI_RANGE_0199_PID 0x0199
#define MTXORB_FTDI_RANGE_019A_PID 0x019A
#define MTXORB_FTDI_RANGE_019B_PID 0x019B
#define MTXORB_FTDI_RANGE_019C_PID 0x019C
#define MTXORB_FTDI_RANGE_019D_PID 0x019D
#define MTXORB_FTDI_RANGE_019E_PID 0x019E
#define MTXORB_FTDI_RANGE_019F_PID 0x019F
#define MTXORB_FTDI_RANGE_01A0_PID 0x01A0
#define MTXORB_FTDI_RANGE_01A1_PID 0x01A1
#define MTXORB_FTDI_RANGE_01A2_PID 0x01A2
#define MTXORB_FTDI_RANGE_01A3_PID 0x01A3
#define MTXORB_FTDI_RANGE_01A4_PID 0x01A4
#define MTXORB_FTDI_RANGE_01A5_PID 0x01A5
#define MTXORB_FTDI_RANGE_01A6_PID 0x01A6
#define MTXORB_FTDI_RANGE_01A7_PID 0x01A7
#define MTXORB_FTDI_RANGE_01A8_PID 0x01A8
#define MTXORB_FTDI_RANGE_01A9_PID 0x01A9
#define MTXORB_FTDI_RANGE_01AA_PID 0x01AA
#define MTXORB_FTDI_RANGE_01AB_PID 0x01AB
#define MTXORB_FTDI_RANGE_01AC_PID 0x01AC
#define MTXORB_FTDI_RANGE_01AD_PID 0x01AD
#define MTXORB_FTDI_RANGE_01AE_PID 0x01AE
#define MTXORB_FTDI_RANGE_01AF_PID 0x01AF
#define MTXORB_FTDI_RANGE_01B0_PID 0x01B0
#define MTXORB_FTDI_RANGE_01B1_PID 0x01B1
#define MTXORB_FTDI_RANGE_01B2_PID 0x01B2
#define MTXORB_FTDI_RANGE_01B3_PID 0x01B3
#define MTXORB_FTDI_RANGE_01B4_PID 0x01B4
#define MTXORB_FTDI_RANGE_01B5_PID 0x01B5
#define MTXORB_FTDI_RANGE_01B6_PID 0x01B6
#define MTXORB_FTDI_RANGE_01B7_PID 0x01B7
#define MTXORB_FTDI_RANGE_01B8_PID 0x01B8
#define MTXORB_FTDI_RANGE_01B9_PID 0x01B9
#define MTXORB_FTDI_RANGE_01BA_PID 0x01BA
#define MTXORB_FTDI_RANGE_01BB_PID 0x01BB
#define MTXORB_FTDI_RANGE_01BC_PID 0x01BC
#define MTXORB_FTDI_RANGE_01BD_PID 0x01BD
#define MTXORB_FTDI_RANGE_01BE_PID 0x01BE
#define MTXORB_FTDI_RANGE_01BF_PID 0x01BF
#define MTXORB_FTDI_RANGE_01C0_PID 0x01C0
#define MTXORB_FTDI_RANGE_01C1_PID 0x01C1
#define MTXORB_FTDI_RANGE_01C2_PID 0x01C2
#define MTXORB_FTDI_RANGE_01C3_PID 0x01C3
#define MTXORB_FTDI_RANGE_01C4_PID 0x01C4
#define MTXORB_FTDI_RANGE_01C5_PID 0x01C5
#define MTXORB_FTDI_RANGE_01C6_PID 0x01C6
#define MTXORB_FTDI_RANGE_01C7_PID 0x01C7
#define MTXORB_FTDI_RANGE_01C8_PID 0x01C8
#define MTXORB_FTDI_RANGE_01C9_PID 0x01C9
#define MTXORB_FTDI_RANGE_01CA_PID 0x01CA
#define MTXORB_FTDI_RANGE_01CB_PID 0x01CB
#define MTXORB_FTDI_RANGE_01CC_PID 0x01CC
#define MTXORB_FTDI_RANGE_01CD_PID 0x01CD
#define MTXORB_FTDI_RANGE_01CE_PID 0x01CE
#define MTXORB_FTDI_RANGE_01CF_PID 0x01CF
#define MTXORB_FTDI_RANGE_01D0_PID 0x01D0
#define MTXORB_FTDI_RANGE_01D1_PID 0x01D1
#define MTXORB_FTDI_RANGE_01D2_PID 0x01D2
#define MTXORB_FTDI_RANGE_01D3_PID 0x01D3
#define MTXORB_FTDI_RANGE_01D4_PID 0x01D4
#define MTXORB_FTDI_RANGE_01D5_PID 0x01D5
#define MTXORB_FTDI_RANGE_01D6_PID 0x01D6
#define MTXORB_FTDI_RANGE_01D7_PID 0x01D7
#define MTXORB_FTDI_RANGE_01D8_PID 0x01D8
#define MTXORB_FTDI_RANGE_01D9_PID 0x01D9
#define MTXORB_FTDI_RANGE_01DA_PID 0x01DA
#define MTXORB_FTDI_RANGE_01DB_PID 0x01DB
#define MTXORB_FTDI_RANGE_01DC_PID 0x01DC
#define MTXORB_FTDI_RANGE_01DD_PID 0x01DD
#define MTXORB_FTDI_RANGE_01DE_PID 0x01DE
#define MTXORB_FTDI_RANGE_01DF_PID 0x01DF
#define MTXORB_FTDI_RANGE_01E0_PID 0x01E0
#define MTXORB_FTDI_RANGE_01E1_PID 0x01E1
#define MTXORB_FTDI_RANGE_01E2_PID 0x01E2
#define MTXORB_FTDI_RANGE_01E3_PID 0x01E3
#define MTXORB_FTDI_RANGE_01E4_PID 0x01E4
#define MTXORB_FTDI_RANGE_01E5_PID 0x01E5
#define MTXORB_FTDI_RANGE_01E6_PID 0x01E6
#define MTXORB_FTDI_RANGE_01E7_PID 0x01E7
#define MTXORB_FTDI_RANGE_01E8_PID 0x01E8
#define MTXORB_FTDI_RANGE_01E9_PID 0x01E9
#define MTXORB_FTDI_RANGE_01EA_PID 0x01EA
#define MTXORB_FTDI_RANGE_01EB_PID 0x01EB
#define MTXORB_FTDI_RANGE_01EC_PID 0x01EC
#define MTXORB_FTDI_RANGE_01ED_PID 0x01ED
#define MTXORB_FTDI_RANGE_01EE_PID 0x01EE
#define MTXORB_FTDI_RANGE_01EF_PID 0x01EF
#define MTXORB_FTDI_RANGE_01F0_PID 0x01F0
#define MTXORB_FTDI_RANGE_01F1_PID 0x01F1
#define MTXORB_FTDI_RANGE_01F2_PID 0x01F2
#define MTXORB_FTDI_RANGE_01F3_PID 0x01F3
#define MTXORB_FTDI_RANGE_01F4_PID 0x01F4
#define MTXORB_FTDI_RANGE_01F5_PID 0x01F5
#define MTXORB_FTDI_RANGE_01F6_PID 0x01F6
#define MTXORB_FTDI_RANGE_01F7_PID 0x01F7
#define MTXORB_FTDI_RANGE_01F8_PID 0x01F8
#define MTXORB_FTDI_RANGE_01F9_PID 0x01F9
#define MTXORB_FTDI_RANGE_01FA_PID 0x01FA
#define MTXORB_FTDI_RANGE_01FB_PID 0x01FB
#define MTXORB_FTDI_RANGE_01FC_PID 0x01FC
#define MTXORB_FTDI_RANGE_01FD_PID 0x01FD
#define MTXORB_FTDI_RANGE_01FE_PID 0x01FE
#define MTXORB_FTDI_RANGE_01FF_PID 0x01FF
/* Interbiometrics USB I/O Board */
/* Developed for Interbiometrics by Rudolf Gugler */
#define INTERBIOMETRICS_VID 0x1209
#define INTERBIOMETRICS_IOBOARD_PID 0x1002
#define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006
/*
* The following are the values for the Perle Systems
* UltraPort USB serial converters
*/
#define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */
/*
* The following are the values for the Sealevel SeaLINK+ adapters.
* (Original list sent by Tuan Hoang. Ian Abbott renamed the macros and
* removed some PIDs that don't seem to match any existing products.)
*/
#define SEALEVEL_VID 0x0c52 /* Sealevel Vendor ID */
#define SEALEVEL_2101_PID 0x2101 /* SeaLINK+232 (2101/2105) */
#define SEALEVEL_2102_PID 0x2102 /* SeaLINK+485 (2102) */
#define SEALEVEL_2103_PID 0x2103 /* SeaLINK+232I (2103) */
#define SEALEVEL_2104_PID 0x2104 /* SeaLINK+485I (2104) */
#define SEALEVEL_2106_PID 0x9020 /* SeaLINK+422 (2106) */
#define SEALEVEL_2201_1_PID 0x2211 /* SeaPORT+2/232 (2201) Port 1 */
#define SEALEVEL_2201_2_PID 0x2221 /* SeaPORT+2/232 (2201) Port 2 */
#define SEALEVEL_2202_1_PID 0x2212 /* SeaPORT+2/485 (2202) Port 1 */
#define SEALEVEL_2202_2_PID 0x2222 /* SeaPORT+2/485 (2202) Port 2 */
#define SEALEVEL_2203_1_PID 0x2213 /* SeaPORT+2 (2203) Port 1 */
#define SEALEVEL_2203_2_PID 0x2223 /* SeaPORT+2 (2203) Port 2 */
#define SEALEVEL_2401_1_PID 0x2411 /* SeaPORT+4/232 (2401) Port 1 */
#define SEALEVEL_2401_2_PID 0x2421 /* SeaPORT+4/232 (2401) Port 2 */
#define SEALEVEL_2401_3_PID 0x2431 /* SeaPORT+4/232 (2401) Port 3 */
#define SEALEVEL_2401_4_PID 0x2441 /* SeaPORT+4/232 (2401) Port 4 */
#define SEALEVEL_2402_1_PID 0x2412 /* SeaPORT+4/485 (2402) Port 1 */
#define SEALEVEL_2402_2_PID 0x2422 /* SeaPORT+4/485 (2402) Port 2 */
#define SEALEVEL_2402_3_PID 0x2432 /* SeaPORT+4/485 (2402) Port 3 */
#define SEALEVEL_2402_4_PID 0x2442 /* SeaPORT+4/485 (2402) Port 4 */
#define SEALEVEL_2403_1_PID 0x2413 /* SeaPORT+4 (2403) Port 1 */
#define SEALEVEL_2403_2_PID 0x2423 /* SeaPORT+4 (2403) Port 2 */
#define SEALEVEL_2403_3_PID 0x2433 /* SeaPORT+4 (2403) Port 3 */
#define SEALEVEL_2403_4_PID 0x2443 /* SeaPORT+4 (2403) Port 4 */
#define SEALEVEL_2801_1_PID 0X2811 /* SeaLINK+8/232 (2801) Port 1 */
#define SEALEVEL_2801_2_PID 0X2821 /* SeaLINK+8/232 (2801) Port 2 */
#define SEALEVEL_2801_3_PID 0X2831 /* SeaLINK+8/232 (2801) Port 3 */
#define SEALEVEL_2801_4_PID 0X2841 /* SeaLINK+8/232 (2801) Port 4 */
#define SEALEVEL_2801_5_PID 0X2851 /* SeaLINK+8/232 (2801) Port 5 */
#define SEALEVEL_2801_6_PID 0X2861 /* SeaLINK+8/232 (2801) Port 6 */
#define SEALEVEL_2801_7_PID 0X2871 /* SeaLINK+8/232 (2801) Port 7 */
#define SEALEVEL_2801_8_PID 0X2881 /* SeaLINK+8/232 (2801) Port 8 */
#define SEALEVEL_2802_1_PID 0X2812 /* SeaLINK+8/485 (2802) Port 1 */
#define SEALEVEL_2802_2_PID 0X2822 /* SeaLINK+8/485 (2802) Port 2 */
#define SEALEVEL_2802_3_PID 0X2832 /* SeaLINK+8/485 (2802) Port 3 */
#define SEALEVEL_2802_4_PID 0X2842 /* SeaLINK+8/485 (2802) Port 4 */
#define SEALEVEL_2802_5_PID 0X2852 /* SeaLINK+8/485 (2802) Port 5 */
#define SEALEVEL_2802_6_PID 0X2862 /* SeaLINK+8/485 (2802) Port 6 */
#define SEALEVEL_2802_7_PID 0X2872 /* SeaLINK+8/485 (2802) Port 7 */
#define SEALEVEL_2802_8_PID 0X2882 /* SeaLINK+8/485 (2802) Port 8 */
#define SEALEVEL_2803_1_PID 0X2813 /* SeaLINK+8 (2803) Port 1 */
#define SEALEVEL_2803_2_PID 0X2823 /* SeaLINK+8 (2803) Port 2 */
#define SEALEVEL_2803_3_PID 0X2833 /* SeaLINK+8 (2803) Port 3 */
#define SEALEVEL_2803_4_PID 0X2843 /* SeaLINK+8 (2803) Port 4 */
#define SEALEVEL_2803_5_PID 0X2853 /* SeaLINK+8 (2803) Port 5 */
#define SEALEVEL_2803_6_PID 0X2863 /* SeaLINK+8 (2803) Port 6 */
#define SEALEVEL_2803_7_PID 0X2873 /* SeaLINK+8 (2803) Port 7 */
#define SEALEVEL_2803_8_PID 0X2883 /* SeaLINK+8 (2803) Port 8 */
/*
* The following are the values for two KOBIL chipcard terminals.
*/
#define KOBIL_VID 0x0d46 /* KOBIL Vendor ID */
#define KOBIL_CONV_B1_PID 0x2020 /* KOBIL Konverter for B1 */
#define KOBIL_CONV_KAAN_PID 0x2021 /* KOBIL_Konverter for KAAN */
/*
* Icom ID-1 digital transceiver
*/
#define ICOM_ID1_VID 0x0C26
#define ICOM_ID1_PID 0x0004
/*
* ASK.fr devices
*/
#define FTDI_ASK_RDR400_PID 0xC991 /* ASK RDR 400 series card reader */
/*
* FTDI USB UART chips used in construction projects from the
* Elektor Electronics magazine (http://elektor-electronics.co.uk)
*/
#define ELEKTOR_VID 0x0C7D
#define ELEKTOR_FT323R_PID 0x0005 /* RFID-Reader, issue 09-2006 */
/*
* DSS-20 Sync Station for Sony Ericsson P800
*/
#define FTDI_DSS20_PID 0xFC82
/*
* Home Electronics (www.home-electro.com) USB gadgets
*/
#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR transceiver */
/* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
/* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
#define FTDI_USB_UIRT_PID 0xF850 /* Product Id */
/* TNC-X USB-to-packet-radio adapter, versions prior to 3.0 (DLP module) */
#define FTDI_TNC_X_PID 0xEBE0
/*
* ELV USB devices submitted by Christian Abt of ELV (www.elv.de).
* All of these devices use FTDI's vendor ID (0x0403).
*
* The previously included PID for the UO 100 module was incorrect.
* In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58).
*
* Armin Laeuger originally sent the PID for the UM 100 module.
*/
#define FTDI_ELV_UR100_PID 0xFB58 /* USB-RS232-Umsetzer (UR 100) */
#define FTDI_ELV_UM100_PID 0xFB5A /* USB-Modul UM 100 */
#define FTDI_ELV_UO100_PID 0xFB5B /* USB-Modul UO 100 */
#define FTDI_ELV_ALC8500_PID 0xF06E /* ALC 8500 Expert */
/* Additional ELV PIDs that default to using the FTDI D2XX drivers on
* MS Windows, rather than the FTDI Virtual Com Port drivers.
* Maybe these will be easier to use with the libftdi/libusb user-space
* drivers, or possibly the Comedi drivers in some cases. */
#define FTDI_ELV_CLI7000_PID 0xFB59 /* Computer-Light-Interface (CLI 7000) */
#define FTDI_ELV_PPS7330_PID 0xFB5C /* Processor-Power-Supply (PPS 7330) */
#define FTDI_ELV_TFM100_PID 0xFB5D /* Temperartur-Feuchte Messgeraet (TFM 100) */
#define FTDI_ELV_UDF77_PID 0xFB5E /* USB DCF Funkurh (UDF 77) */
#define FTDI_ELV_UIO88_PID 0xFB5F /* USB-I/O Interface (UIO 88) */
#define FTDI_ELV_UAD8_PID 0xF068 /* USB-AD-Wandler (UAD 8) */
#define FTDI_ELV_UDA7_PID 0xF069 /* USB-DA-Wandler (UDA 7) */
#define FTDI_ELV_USI2_PID 0xF06A /* USB-Schrittmotoren-Interface (USI 2) */
#define FTDI_ELV_T1100_PID 0xF06B /* Thermometer (T 1100) */
#define FTDI_ELV_PCD200_PID 0xF06C /* PC-Datenlogger (PCD 200) */
#define FTDI_ELV_ULA200_PID 0xF06D /* USB-LCD-Ansteuerung (ULA 200) */
#define FTDI_ELV_FHZ1000PC_PID 0xF06F /* FHZ 1000 PC */
#define FTDI_ELV_CSI8_PID 0xE0F0 /* Computer-Schalt-Interface (CSI 8) */
#define FTDI_ELV_EM1000DL_PID 0xE0F1 /* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */
#define FTDI_ELV_PCK100_PID 0xE0F2 /* PC-Kabeltester (PCK 100) */
#define FTDI_ELV_RFP500_PID 0xE0F3 /* HF-Leistungsmesser (RFP 500) */
#define FTDI_ELV_FS20SIG_PID 0xE0F4 /* Signalgeber (FS 20 SIG) */
#define FTDI_ELV_WS300PC_PID 0xE0F6 /* PC-Wetterstation (WS 300 PC) */
#define FTDI_ELV_FHZ1300PC_PID 0xE0E8 /* FHZ 1300 PC */
#define FTDI_ELV_WS500_PID 0xE0E9 /* PC-Wetterstation (WS 500) */
#define FTDI_ELV_HS485_PID 0xE0EA /* USB to RS-485 adapter */
#define FTDI_ELV_EM1010PC_PID 0xE0EF /* Engery monitor EM 1010 PC */
#define FTDI_PHI_FISCO_PID 0xE40B /* PHI Fisco USB to Serial cable */
/*
* Definitions for ID TECH (www.idt-net.com) devices
*/
#define IDTECH_VID 0x0ACD /* ID TECH Vendor ID */
#define IDTECH_IDT1221U_PID 0x0300 /* IDT1221U USB to RS-232 adapter */
/*
* Definitions for Omnidirectional Control Technology, Inc. devices
*/
#define OCT_VID 0x0B39 /* OCT vendor ID */
/* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
/* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
/* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
#define OCT_US101_PID 0x0421 /* OCT US101 USB to RS-232 */
/* an infrared receiver for user access control with IR tags */
#define FTDI_PIEGROUP_PID 0xF208 /* Product Id */
/*
* Definitions for Artemis astronomical USB based cameras
* Check it at http://www.artemisccd.co.uk/
*/
#define FTDI_ARTEMIS_PID 0xDF28 /* All Artemis Cameras */
/*
* Definitions for ATIK Instruments astronomical USB based cameras
* Check it at http://www.atik-instruments.com/
*/
#define FTDI_ATIK_ATK16_PID 0xDF30 /* ATIK ATK-16 Grayscale Camera */
#define FTDI_ATIK_ATK16C_PID 0xDF32 /* ATIK ATK-16C Colour Camera */
#define FTDI_ATIK_ATK16HR_PID 0xDF31 /* ATIK ATK-16HR Grayscale Camera */
#define FTDI_ATIK_ATK16HRC_PID 0xDF33 /* ATIK ATK-16HRC Colour Camera */
#define FTDI_ATIK_ATK16IC_PID 0xDF35 /* ATIK ATK-16IC Grayscale Camera */
/*
* Protego product ids
*/
#define PROTEGO_SPECIAL_1 0xFC70 /* special/unknown device */
#define PROTEGO_R2X0 0xFC71 /* R200-USB TRNG unit (R210, R220, and R230) */
#define PROTEGO_SPECIAL_3 0xFC72 /* special/unknown device */
#define PROTEGO_SPECIAL_4 0xFC73 /* special/unknown device */
/*
* Gude Analog- und Digitalsysteme GmbH
*/
#define FTDI_GUDEADS_E808_PID 0xE808
#define FTDI_GUDEADS_E809_PID 0xE809
#define FTDI_GUDEADS_E80A_PID 0xE80A
#define FTDI_GUDEADS_E80B_PID 0xE80B
#define FTDI_GUDEADS_E80C_PID 0xE80C
#define FTDI_GUDEADS_E80D_PID 0xE80D
#define FTDI_GUDEADS_E80E_PID 0xE80E
#define FTDI_GUDEADS_E80F_PID 0xE80F
#define FTDI_GUDEADS_E888_PID 0xE888 /* Expert ISDN Control USB */
#define FTDI_GUDEADS_E889_PID 0xE889 /* USB RS-232 OptoBridge */
#define FTDI_GUDEADS_E88A_PID 0xE88A
#define FTDI_GUDEADS_E88B_PID 0xE88B
#define FTDI_GUDEADS_E88C_PID 0xE88C
#define FTDI_GUDEADS_E88D_PID 0xE88D
#define FTDI_GUDEADS_E88E_PID 0xE88E
#define FTDI_GUDEADS_E88F_PID 0xE88F
/*
* Linx Technologies product ids
*/
#define LINX_SDMUSBQSS_PID 0xF448 /* Linx SDM-USB-QS-S */
#define LINX_MASTERDEVEL2_PID 0xF449 /* Linx Master Development 2.0 */
#define LINX_FUTURE_0_PID 0xF44A /* Linx future device */
#define LINX_FUTURE_1_PID 0xF44B /* Linx future device */
#define LINX_FUTURE_2_PID 0xF44C /* Linx future device */
/* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
/* unit for PIC16's/PIC18's */
#define FTDI_CCSICDU20_0_PID 0xF9D0
#define FTDI_CCSICDU40_1_PID 0xF9D1
#define FTDI_CCSMACHX_2_PID 0xF9D2
/* Inside Accesso contactless reader (http://www.insidefr.com) */
#define INSIDE_ACCESSO 0xFAD0
/*
* Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
*/
#define INTREPID_VID 0x093C
#define INTREPID_VALUECAN_PID 0x0601
#define INTREPID_NEOVI_PID 0x0701
/*
* Falcom Wireless Communications GmbH
*/
#define FALCOM_VID 0x0F94 /* Vendor Id */
#define FALCOM_TWIST_PID 0x0001 /* Falcom Twist USB GPRS modem */
#define FALCOM_SAMBA_PID 0x0005 /* Falcom Samba USB GPRS modem */
/*
* SUUNTO product ids
*/
#define FTDI_SUUNTO_SPORTS_PID 0xF680 /* Suunto Sports instrument */
/*
* Oceanic product ids
*/
#define FTDI_OCEANIC_PID 0xF460 /* Oceanic dive instrument */
/*
* TTi (Thurlby Thandar Instruments)
*/
#define TTI_VID 0x103E /* Vendor Id */
#define TTI_QL355P_PID 0x03E8 /* TTi QL355P power supply */
/*
* Definitions for B&B Electronics products.
*/
#define BANDB_VID 0x0856 /* B&B Electronics Vendor ID */
#define BANDB_USOTL4_PID 0xAC01 /* USOTL4 Isolated RS-485 Converter */
#define BANDB_USTL4_PID 0xAC02 /* USTL4 RS-485 Converter */
#define BANDB_USO9ML2_PID 0xAC03 /* USO9ML2 Isolated RS-232 Converter */
/*
* RM Michaelides CANview USB (http://www.rmcan.com)
* CAN fieldbus interface adapter, added by port GmbH www.port.de)
* Ian Abbott changed the macro names for consistency.
*/
#define FTDI_RM_CANVIEW_PID 0xfd60 /* Product Id */
/*
* EVER Eco Pro UPS (http://www.ever.com.pl/)
*/
#define EVER_ECO_PRO_CDS 0xe520 /* RS-232 converter */
/*
* 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
* USB-TTY activ, USB-TTY passiv. Some PIDs are used by several devices
* and I'm not entirely sure which are used by which.
*/
#define FTDI_4N_GALAXY_DE_1_PID 0xF3C0
#define FTDI_4N_GALAXY_DE_2_PID 0xF3C1
/*
* Mobility Electronics products.
*/
#define MOBILITY_VID 0x1342
#define MOBILITY_USB_SERIAL_PID 0x0202 /* EasiDock USB 200 serial */
/*
* microHAM product IDs (http://www.microham.com).
* Submitted by Justin Burket (KL1RL) <zorton@jtan.com>
* and Mike Studer (K6EEP) <k6eep@hamsoftware.org>.
* Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file.
*/
#define FTDI_MHAM_KW_PID 0xEEE8 /* USB-KW interface */
#define FTDI_MHAM_YS_PID 0xEEE9 /* USB-YS interface */
#define FTDI_MHAM_Y6_PID 0xEEEA /* USB-Y6 interface */
#define FTDI_MHAM_Y8_PID 0xEEEB /* USB-Y8 interface */
#define FTDI_MHAM_IC_PID 0xEEEC /* USB-IC interface */
#define FTDI_MHAM_DB9_PID 0xEEED /* USB-DB9 interface */
#define FTDI_MHAM_RS232_PID 0xEEEE /* USB-RS232 interface */
#define FTDI_MHAM_Y9_PID 0xEEEF /* USB-Y9 interface */
/*
* Active Robots product ids.
*/
#define FTDI_ACTIVE_ROBOTS_PID 0xE548 /* USB comms board */
/*
* Xsens Technologies BV products (http://www.xsens.com).
*/
#define XSENS_CONVERTER_0_PID 0xD388
#define XSENS_CONVERTER_1_PID 0xD389
#define XSENS_CONVERTER_2_PID 0xD38A
#define XSENS_CONVERTER_3_PID 0xD38B
#define XSENS_CONVERTER_4_PID 0xD38C
#define XSENS_CONVERTER_5_PID 0xD38D
#define XSENS_CONVERTER_6_PID 0xD38E
#define XSENS_CONVERTER_7_PID 0xD38F
/*
* Teratronik product ids.
* Submitted by O. Wölfelschneider.
*/
#define FTDI_TERATRONIK_VCP_PID 0xEC88 /* Teratronik device (preferring VCP driver on windows) */
#define FTDI_TERATRONIK_D2XX_PID 0xEC89 /* Teratronik device (preferring D2XX driver on windows) */
/*
* Evolution Robotics products (http://www.evolution.com/).
* Submitted by Shawn M. Lavelle.
*/
#define EVOLUTION_VID 0xDEEE /* Vendor ID */
#define EVOLUTION_ER1_PID 0x0300 /* ER1 Control Module */
#define EVO_8U232AM_PID 0x02FF /* Evolution robotics RCM2 (FT232AM)*/
#define EVO_HYBRID_PID 0x0302 /* Evolution robotics RCM4 PID (FT232BM)*/
#define EVO_RCM4_PID 0x0303 /* Evolution robotics RCM4 PID */
/* Pyramid Computer GmbH */
#define FTDI_PYRAMID_PID 0xE6C8 /* Pyramid Appliance Display */
/*
* Posiflex inc retail equipment (http://www.posiflex.com.tw)
*/
#define POSIFLEX_VID 0x0d3a /* Vendor ID */
#define POSIFLEX_PP7000_PID 0x0300 /* PP-7000II thermal printer */
/*
* Westrex International devices submitted by Cory Lee
*/
#define FTDI_WESTREX_MODEL_777_PID 0xDC00 /* Model 777 */
#define FTDI_WESTREX_MODEL_8900F_PID 0xDC01 /* Model 8900F */
/*
* RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
*/
#define FTDI_RRCIRKITS_LOCOBUFFER_PID 0xc7d0 /* LocoBuffer USB */
/*
* Eclo (http://www.eclo.pt/) product IDs.
* PID 0xEA90 submitted by Martin Grill.
*/
#define FTDI_ECLO_COM_1WIRE_PID 0xEA90 /* COM to 1-Wire USB adaptor */
/*
* Papouch products (http://www.papouch.com/)
* Submitted by Folkert van Heusden
*/
#define PAPOUCH_VID 0x5050 /* Vendor ID */
#define PAPOUCH_TMU_PID 0x0400 /* TMU USB Thermometer */
#define PAPOUCH_QUIDO4x4_PID 0x0900 /* Quido 4/4 Module */
/*
* ACG Identification Technologies GmbH products (http://www.acg.de/).
* Submitted by anton -at- goto10 -dot- org.
*/
#define FTDI_ACG_HFDUAL_PID 0xDD20 /* HF Dual ISO Reader (RFID) */
/*
* Yost Engineering, Inc. products (www.yostengineering.com).
* PID 0xE050 submitted by Aaron Prose.
*/
#define FTDI_YEI_SERVOCENTER31_PID 0xE050 /* YEI ServoCenter3.1 USB */
/*
* ThorLabs USB motor drivers
*/
#define FTDI_THORLABS_PID 0xfaf0 /* ThorLabs USB motor drivers */
/*
* Testo products (http://www.testo.com/)
* Submitted by Colin Leroy
*/
#define TESTO_VID 0x128D
#define TESTO_USB_INTERFACE_PID 0x0001
/*
* Gamma Scout (http://gamma-scout.com/). Submitted by rsc@runtux.com.
*/
#define FTDI_GAMMA_SCOUT_PID 0xD678 /* Gamma Scout online */
/*
* Tactrix OpenPort (ECU) devices.
* OpenPort 1.3M submitted by Donour Sizemore.
* OpenPort 1.3S and 1.3U submitted by Ian Abbott.
*/
#define FTDI_TACTRIX_OPENPORT_13M_PID 0xCC48 /* OpenPort 1.3 Mitsubishi */
#define FTDI_TACTRIX_OPENPORT_13S_PID 0xCC49 /* OpenPort 1.3 Subaru */
#define FTDI_TACTRIX_OPENPORT_13U_PID 0xCC4A /* OpenPort 1.3 Universal */
/*
* Telldus Technologies
*/
#define TELLDUS_VID 0x1781 /* Vendor ID */
#define TELLDUS_TELLSTICK_PID 0x0C30 /* RF control dongle 433 MHz using FT232RL */
/*
* IBS elektronik product ids
* Submitted by Thomas Schleusener
*/
#define FTDI_IBS_US485_PID 0xff38 /* IBS US485 (USB<-->RS422/485 interface) */
#define FTDI_IBS_PICPRO_PID 0xff39 /* IBS PIC-Programmer */
#define FTDI_IBS_PCMCIA_PID 0xff3a /* IBS Card reader for PCMCIA SRAM-cards */
#define FTDI_IBS_PK1_PID 0xff3b /* IBS PK1 - Particel counter */
#define FTDI_IBS_RS232MON_PID 0xff3c /* IBS RS232 - Monitor */
#define FTDI_IBS_APP70_PID 0xff3d /* APP 70 (dust monitoring system) */
#define FTDI_IBS_PEDO_PID 0xff3e /* IBS PEDO-Modem (RF modem 868.35 MHz) */
#define FTDI_IBS_PROD_PID 0xff3f /* future device */
/*
* MaxStream devices www.maxstream.net
*/
#define FTDI_MAXSTREAM_PID 0xEE18 /* Xbee PKG-U Module */
/* Olimex */
#define OLIMEX_VID 0x15BA
#define OLIMEX_ARM_USB_OCD_PID 0x0003
/* Luminary Micro Stellaris Boards, VID = FTDI_VID */
/* FTDI 2332C Dual channel device, side A=245 FIFO (JTAG), Side B=RS232 UART */
#define LMI_LM3S_DEVEL_BOARD_PID 0xbcd8
#define LMI_LM3S_EVAL_BOARD_PID 0xbcd9
/* www.elsterelectricity.com Elster Unicom III Optical Probe */
#define FTDI_ELSTER_UNICOM_PID 0xE700 /* Product Id */
/*
* The Mobility Lab (TML)
* Submitted by Pierre Castella
*/
#define TML_VID 0x1B91 /* Vendor ID */
#define TML_USB_SERIAL_PID 0x0064 /* USB - Serial Converter */
/* Propox devices */
#define FTDI_PROPOX_JTAGCABLEII_PID 0xD738
/* Rig Expert Ukraine devices */
#define FTDI_REU_TINY_PID 0xED22 /* RigExpert Tiny */
/* Domintell products http://www.domintell.com */
#define FTDI_DOMINTELL_DGQG_PID 0xEF50 /* Master */
#define FTDI_DOMINTELL_DUSB_PID 0xEF51 /* DUSB01 module */
/* Commands */
#define FTDI_SIO_RESET 0 /* Reset the port */
#define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */
#define FTDI_SIO_SET_FLOW_CTRL 2 /* Set flow control register */
#define FTDI_SIO_SET_BAUD_RATE 3 /* Set baud rate */
#define FTDI_SIO_SET_DATA 4 /* Set the data characteristics of the port */
#define FTDI_SIO_GET_MODEM_STATUS 5 /* Retrieve current value of modern status register */
#define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
#define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
#define FTDI_SIO_SET_LATENCY_TIMER 9 /* Set the latency timer */
#define FTDI_SIO_GET_LATENCY_TIMER 10 /* Get the latency timer */
/*
* FIC / OpenMoko, Inc. http://wiki.openmoko.org/wiki/Neo1973_Debug_Board_v3
* Submitted by Harald Welte <laforge@openmoko.org>
*/
#define FIC_VID 0x1457
#define FIC_NEO1973_DEBUG_PID 0x5118
/*
* RATOC REX-USB60F
*/
#define RATOC_VENDOR_ID 0x0584
#define RATOC_PRODUCT_ID_USB60F 0xb020
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_E2_READ
* wValue: 0
* wIndex: Address of word to read
* wLength: 2
* Data: Will return a word of data from E2Address
*
*/
/* Port Identifier Table */
#define PIT_DEFAULT 0 /* SIOA */
#define PIT_SIOA 1 /* SIOA */
/* The device this driver is tested with one has only one port */
#define PIT_SIOB 2 /* SIOB */
#define PIT_PARALLEL 3 /* Parallel */
/* FTDI_SIO_RESET */
#define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
#define FTDI_SIO_RESET_REQUEST_TYPE 0x40
#define FTDI_SIO_RESET_SIO 0
#define FTDI_SIO_RESET_PURGE_RX 1
#define FTDI_SIO_RESET_PURGE_TX 2
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_RESET
* wValue: Control Value
* 0 = Reset SIO
* 1 = Purge RX buffer
* 2 = Purge TX buffer
* wIndex: Port
* wLength: 0
* Data: None
*
* The Reset SIO command has this effect:
*
* Sets flow control set to 'none'
* Event char = $0D
* Event trigger = disabled
* Purge RX buffer
* Purge TX buffer
* Clear DTR
* Clear RTS
* baud and data format not reset
*
* The Purge RX and TX buffer commands affect nothing except the buffers
*
*/
/* FTDI_SIO_SET_BAUDRATE */
#define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_BAUDRATE_REQUEST 3
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_SET_BAUDRATE
* wValue: BaudDivisor value - see below
* wIndex: Port
* wLength: 0
* Data: None
* The BaudDivisor values are calculated as follows:
* - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
* I knew how to detect old chips to select proper base clock!
* - BaudDivisor is a fixed point number encoded in a funny way.
* (--WRONG WAY OF THINKING--)
* BaudDivisor is a fixed point number encoded with following bit weighs:
* (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
* end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
* (--THE REALITY--)
* The both-bits-set has quite different meaning from 0.75 - the chip designers
* have decided it to mean 0.125 instead of 0.75.
* This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
* and Flow Control Consideration for USB to RS232".
* - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
* automagically re-encode the resulting value to take fractions into consideration.
* As all values are integers, some bit twiddling is in order:
* BaudDivisor = (BaseClock / 16 / BaudRate) |
* (((BaseClock / 2 / BaudRate) & 4) ? 0x4000 // 0.5
* : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000 // 0.25
* : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000 // 0.125
* : 0)
*
* For the FT232BM, a 17th divisor bit was introduced to encode the multiples
* of 0.125 missing from the FT8U232AM. Bits 16 to 14 are coded as follows
* (the first four codes are the same as for the FT8U232AM, where bit 16 is
* always 0):
* 000 - add .000 to divisor
* 001 - add .500 to divisor
* 010 - add .250 to divisor
* 011 - add .125 to divisor
* 100 - add .375 to divisor
* 101 - add .625 to divisor
* 110 - add .750 to divisor
* 111 - add .875 to divisor
* Bits 15 to 0 of the 17-bit divisor are placed in the urb value. Bit 16 is
* placed in bit 0 of the urb index.
*
* Note that there are a couple of special cases to support the highest baud
* rates. If the calculated divisor value is 1, this needs to be replaced with
* 0. Additionally for the FT232BM, if the calculated divisor value is 0x4001
* (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
* not supported by the FT8U232AM).
*/
typedef enum {
SIO = 1,
FT8U232AM = 2,
FT232BM = 3,
FT2232C = 4,
FT232RL = 5,
} ftdi_chip_type_t;
typedef enum {
ftdi_sio_b300 = 0,
ftdi_sio_b600 = 1,
ftdi_sio_b1200 = 2,
ftdi_sio_b2400 = 3,
ftdi_sio_b4800 = 4,
ftdi_sio_b9600 = 5,
ftdi_sio_b19200 = 6,
ftdi_sio_b38400 = 7,
ftdi_sio_b57600 = 8,
ftdi_sio_b115200 = 9
} FTDI_SIO_baudrate_t;
/*
* The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
* are calculated internally.
*/
#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
#define FTDI_SIO_SET_BREAK (0x1 << 14)
/* FTDI_SIO_SET_DATA */
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_SET_DATA
* wValue: Data characteristics (see below)
* wIndex: Port
* wLength: 0
* Data: No
*
* Data characteristics
*
* B0..7 Number of data bits
* B8..10 Parity
* 0 = None
* 1 = Odd
* 2 = Even
* 3 = Mark
* 4 = Space
* B11..13 Stop Bits
* 0 = 1
* 1 = 1.5
* 2 = 2
* B14
* 1 = TX ON (break)
* 0 = TX OFF (normal state)
* B15 Reserved
*
*/
/* FTDI_SIO_MODEM_CTRL */
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_MODEM_CTRL
* wValue: ControlValue (see below)
* wIndex: Port
* wLength: 0
* Data: None
*
* NOTE: If the device is in RTS/CTS flow control, the RTS set by this
* command will be IGNORED without an error being returned
* Also - you can not set DTR and RTS with one control message
*/
#define FTDI_SIO_SET_DTR_MASK 0x1
#define FTDI_SIO_SET_DTR_HIGH (1 | (FTDI_SIO_SET_DTR_MASK << 8))
#define FTDI_SIO_SET_DTR_LOW (0 | (FTDI_SIO_SET_DTR_MASK << 8))
#define FTDI_SIO_SET_RTS_MASK 0x2
#define FTDI_SIO_SET_RTS_HIGH (2 | (FTDI_SIO_SET_RTS_MASK << 8))
#define FTDI_SIO_SET_RTS_LOW (0 | (FTDI_SIO_SET_RTS_MASK << 8))
/*
* ControlValue
* B0 DTR state
* 0 = reset
* 1 = set
* B1 RTS state
* 0 = reset
* 1 = set
* B2..7 Reserved
* B8 DTR state enable
* 0 = ignore
* 1 = use DTR state
* B9 RTS state enable
* 0 = ignore
* 1 = use RTS state
* B10..15 Reserved
*/
/* FTDI_SIO_SET_FLOW_CTRL */
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
#define FTDI_SIO_DISABLE_FLOW_CTRL 0x0
#define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
#define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
#define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_FLOW_CTRL
* wValue: Xoff/Xon
* wIndex: Protocol/Port - hIndex is protocl / lIndex is port
* wLength: 0
* Data: None
*
* hIndex protocol is:
* B0 Output handshaking using RTS/CTS
* 0 = disabled
* 1 = enabled
* B1 Output handshaking using DTR/DSR
* 0 = disabled
* 1 = enabled
* B2 Xon/Xoff handshaking
* 0 = disabled
* 1 = enabled
*
* A value of zero in the hIndex field disables handshaking
*
* If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
* and the lValue field contains the XON character.
*/
/*
* FTDI_SIO_GET_LATENCY_TIMER
*
* Set the timeout interval. The FTDI collects data from the slave
* device, transmitting it to the host when either A) 62 bytes are
* received, or B) the timeout interval has elapsed and the buffer
* contains at least 1 byte. Setting this value to a small number
* can dramatically improve performance for applications which send
* small packets, since the default value is 16ms.
*/
#define FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
#define FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_SIO_GET_LATENCY_TIMER
* wValue: 0
* wIndex: Port
* wLength: 0
* Data: latency (on return)
*/
/*
* FTDI_SIO_SET_LATENCY_TIMER
*
* Set the timeout interval. The FTDI collects data from the slave
* device, transmitting it to the host when either A) 62 bytes are
* received, or B) the timeout interval has elapsed and the buffer
* contains at least 1 byte. Setting this value to a small number
* can dramatically improve performance for applications which send
* small packets, since the default value is 16ms.
*/
#define FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
#define FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_LATENCY_TIMER
* wValue: Latency (milliseconds)
* wIndex: Port
* wLength: 0
* Data: None
*
* wValue:
* B0..7 Latency timer
* B8..15 0
*
*/
/*
* FTDI_SIO_SET_EVENT_CHAR
*
* Set the special event character for the specified communications port.
* If the device sees this character it will immediately return the
* data read so far - rather than wait 40ms or until 62 bytes are read
* which is what normally happens.
*/
#define FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
#define FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_EVENT_CHAR
* wValue: EventChar
* wIndex: Port
* wLength: 0
* Data: None
*
* wValue:
* B0..7 Event Character
* B8 Event Character Processing
* 0 = disabled
* 1 = enabled
* B9..15 Reserved
*
*/
/* FTDI_SIO_SET_ERROR_CHAR */
/* Set the parity error replacement character for the specified communications port */
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_EVENT_CHAR
* wValue: Error Char
* wIndex: Port
* wLength: 0
* Data: None
*
*Error Char
* B0..7 Error Character
* B8 Error Character Processing
* 0 = disabled
* 1 = enabled
* B9..15 Reserved
*
*/
/* FTDI_SIO_GET_MODEM_STATUS */
/* Retrieve the current value of the modem status register */
#define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
#define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
#define FTDI_SIO_CTS_MASK 0x10
#define FTDI_SIO_DSR_MASK 0x20
#define FTDI_SIO_RI_MASK 0x40
#define FTDI_SIO_RLSD_MASK 0x80
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_SIO_GET_MODEM_STATUS
* wValue: zero
* wIndex: Port
* wLength: 1
* Data: Status
*
* One byte of data is returned
* B0..3 0
* B4 CTS
* 0 = inactive
* 1 = active
* B5 DSR
* 0 = inactive
* 1 = active
* B6 Ring Indicator (RI)
* 0 = inactive
* 1 = active
* B7 Receive Line Signal Detect (RLSD)
* 0 = inactive
* 1 = active
*/
/* Descriptors returned by the device
*
* Device Descriptor
*
* Offset Field Size Value Description
* 0 bLength 1 0x12 Size of descriptor in bytes
* 1 bDescriptorType 1 0x01 DEVICE Descriptor Type
* 2 bcdUSB 2 0x0110 USB Spec Release Number
* 4 bDeviceClass 1 0x00 Class Code
* 5 bDeviceSubClass 1 0x00 SubClass Code
* 6 bDeviceProtocol 1 0x00 Protocol Code
* 7 bMaxPacketSize0 1 0x08 Maximum packet size for endpoint 0
* 8 idVendor 2 0x0403 Vendor ID
* 10 idProduct 2 0x8372 Product ID (FTDI_SIO_PID)
* 12 bcdDevice 2 0x0001 Device release number
* 14 iManufacturer 1 0x01 Index of man. string desc
* 15 iProduct 1 0x02 Index of prod string desc
* 16 iSerialNumber 1 0x02 Index of serial nmr string desc
* 17 bNumConfigurations 1 0x01 Number of possible configurations
*
* Configuration Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x09 Size of descriptor in bytes
* 1 bDescriptorType 1 0x02 CONFIGURATION Descriptor Type
* 2 wTotalLength 2 0x0020 Total length of data
* 4 bNumInterfaces 1 0x01 Number of interfaces supported
* 5 bConfigurationValue 1 0x01 Argument for SetCOnfiguration() req
* 6 iConfiguration 1 0x02 Index of config string descriptor
* 7 bmAttributes 1 0x20 Config characteristics Remote Wakeup
* 8 MaxPower 1 0x1E Max power consumption
*
* Interface Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x09 Size of descriptor in bytes
* 1 bDescriptorType 1 0x04 INTERFACE Descriptor Type
* 2 bInterfaceNumber 1 0x00 Number of interface
* 3 bAlternateSetting 1 0x00 Value used to select alternate
* 4 bNumEndpoints 1 0x02 Number of endpoints
* 5 bInterfaceClass 1 0xFF Class Code
* 6 bInterfaceSubClass 1 0xFF Subclass Code
* 7 bInterfaceProtocol 1 0xFF Protocol Code
* 8 iInterface 1 0x02 Index of interface string description
*
* IN Endpoint Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x07 Size of descriptor in bytes
* 1 bDescriptorType 1 0x05 ENDPOINT descriptor type
* 2 bEndpointAddress 1 0x82 Address of endpoint
* 3 bmAttributes 1 0x02 Endpoint attributes - Bulk
* 4 bNumEndpoints 2 0x0040 maximum packet size
* 5 bInterval 1 0x00 Interval for polling endpoint
*
* OUT Endpoint Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x07 Size of descriptor in bytes
* 1 bDescriptorType 1 0x05 ENDPOINT descriptor type
* 2 bEndpointAddress 1 0x02 Address of endpoint
* 3 bmAttributes 1 0x02 Endpoint attributes - Bulk
* 4 bNumEndpoints 2 0x0040 maximum packet size
* 5 bInterval 1 0x00 Interval for polling endpoint
*
* DATA FORMAT
*
* IN Endpoint
*
* The device reserves the first two bytes of data on this endpoint to contain the current
* values of the modem and line status registers. In the absence of data, the device
* generates a message consisting of these two status bytes every 40 ms
*
* Byte 0: Modem Status
*
* Offset Description
* B0 Reserved - must be 1
* B1 Reserved - must be 0
* B2 Reserved - must be 0
* B3 Reserved - must be 0
* B4 Clear to Send (CTS)
* B5 Data Set Ready (DSR)
* B6 Ring Indicator (RI)
* B7 Receive Line Signal Detect (RLSD)
*
* Byte 1: Line Status
*
* Offset Description
* B0 Data Ready (DR)
* B1 Overrun Error (OE)
* B2 Parity Error (PE)
* B3 Framing Error (FE)
* B4 Break Interrupt (BI)
* B5 Transmitter Holding Register (THRE)
* B6 Transmitter Empty (TEMT)
* B7 Error in RCVR FIFO
*
*/
#define FTDI_RS0_CTS (1 << 4)
#define FTDI_RS0_DSR (1 << 5)
#define FTDI_RS0_RI (1 << 6)
#define FTDI_RS0_RLSD (1 << 7)
#define FTDI_RS_DR 1
#define FTDI_RS_OE (1<<1)
#define FTDI_RS_PE (1<<2)
#define FTDI_RS_FE (1<<3)
#define FTDI_RS_BI (1<<4)
#define FTDI_RS_THRE (1<<5)
#define FTDI_RS_TEMT (1<<6)
#define FTDI_RS_FIFO (1<<7)
/*
* OUT Endpoint
*
* This device reserves the first bytes of data on this endpoint contain the length
* and port identifier of the message. For the FTDI USB Serial converter the port
* identifier is always 1.
*
* Byte 0: Line Status
*
* Offset Description
* B0 Reserved - must be 1
* B1 Reserved - must be 0
* B2..7 Length of message - (not including Byte 0)
*
*/
