#
# USB Host Controller Drivers
#
comment "USB Host Controller Drivers"
depends on USB
config USB_EHCI_HCD
tristate "EHCI HCD (USB 2.0) support"
depends on USB && USB_ARCH_HAS_EHCI
---help---
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
If your USB host controller supports USB 2.0, you will likely want to
configure this Host Controller Driver. At the time of this writing,
the primary implementation of EHCI is a chip from NEC, widely available
in add-on PCI cards, but implementations are in the works from other
vendors including Intel and Philips. Motherboard support is appearing.
EHCI controllers are packaged with "companion" host controllers (OHCI
or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
will connect to EHCI if the device is high speed, otherwise they
connect to a companion controller. If you configure EHCI, you should
probably configure the OHCI (for NEC and some other vendors) USB Host
Controller Driver or UHCI (for Via motherboards) Host Controller
Driver too.
You may want to read <file:Documentation/usb/ehci.txt>.
To compile this driver as a module, choose M here: the
module will be called ehci-hcd.
config USB_EHCI_ROOT_HUB_TT
bool "Root Hub Transaction Translators (EXPERIMENTAL)"
depends on USB_EHCI_HCD && EXPERIMENTAL
---help---
Some EHCI chips have vendor-specific extensions to integrate
transaction translators, so that no OHCI or UHCI companion
controller is needed. It's safe to say "y" even if your
controller doesn't support this feature.
This supports the EHCI implementation that's originally
from ARC, and has since changed hands a few times.
config USB_EHCI_TT_NEWSCHED
bool "Improved Transaction Translator scheduling (EXPERIMENTAL)"
depends on USB_EHCI_HCD && EXPERIMENTAL
---help---
This changes the periodic scheduling code to fill more of the low
and full speed bandwidth available from the Transaction Translator
(TT) in USB 2.0 hubs. Without this, only one transfer will be
issued in each microframe, significantly reducing the number of
periodic low/fullspeed transfers possible.
If you have multiple periodic low/fullspeed devices connected to a
highspeed USB hub which is connected to a highspeed USB Host
Controller, and some of those devices will not work correctly
(possibly due to "ENOSPC" or "-28" errors), say Y.
If unsure, say N.
config USB_EHCI_BIG_ENDIAN_MMIO
bool
depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || ARCH_IXP4XX)
default y
config USB_EHCI_BIG_ENDIAN_DESC
bool
depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX)
default y
config USB_EHCI_FSL
bool "Support for Freescale on-chip EHCI USB controller"
depends on USB_EHCI_HCD && FSL_SOC
select USB_EHCI_ROOT_HUB_TT
---help---
Variation of ARC USB block used in some Freescale chips.
config USB_EHCI_HCD_PPC_OF
bool "EHCI support for PPC USB controller on OF platform bus"
depends on USB_EHCI_HCD && PPC_OF
default y
---help---
Enables support for the USB controller present on the PowerPC
OpenFirmware platform bus.
config USB_ISP116X_HCD
tristate "ISP116X HCD support"
depends on USB
---help---
The ISP1160 and ISP1161 chips are USB host controllers. Enable this
option if your board has this chip. If unsure, say N.
This driver does not support isochronous transfers.
To compile this driver as a module, choose M here: the
module will be called isp116x-hcd.
config USB_OHCI_HCD
tristate "OHCI HCD support"
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
select I2C if ARCH_PNX4008
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
UHCI specification. If your USB host controller follows the OHCI spec,
say Y. On most non-x86 systems, and on x86 hardware that's not using a
USB controller from Intel or VIA, this is appropriate. If your host
controller doesn't use PCI, this is probably appropriate. For a PCI
based system where you're not sure, the "lspci -v" entry will list the
right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
To compile this driver as a module, choose M here: the
module will be called ohci-hcd.
config USB_OHCI_HCD_PPC_SOC
bool "OHCI support for on-chip PPC USB controller"
depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
default y
select USB_OHCI_BIG_ENDIAN_DESC
select USB_OHCI_BIG_ENDIAN_MMIO
---help---
Enables support for the USB controller on the MPC52xx or
STB03xxx processor chip. If unsure, say Y.
config USB_OHCI_HCD_PPC_OF
bool "OHCI support for PPC USB controller on OF platform bus"
depends on USB_OHCI_HCD && PPC_OF
default y
---help---
Enables support for the USB controller PowerPC present on the
OpenFirmware platform bus.
config USB_OHCI_HCD_PPC_OF_BE
bool "Support big endian HC"
depends on USB_OHCI_HCD_PPC_OF
default y
select USB_OHCI_BIG_ENDIAN_DESC
select USB_OHCI_BIG_ENDIAN_MMIO
config USB_OHCI_HCD_PPC_OF_LE
bool "Support little endian HC"
depends on USB_OHCI_HCD_PPC_OF
default n
select USB_OHCI_LITTLE_ENDIAN
config USB_OHCI_HCD_PCI
bool "OHCI support for PCI-bus USB controllers"
depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
default y
select USB_OHCI_LITTLE_ENDIAN
---help---
Enables support for PCI-bus plug-in USB controller cards.
If unsure, say Y.
config USB_OHCI_HCD_SSB
bool "OHCI support for Broadcom SSB OHCI core"
depends on USB_OHCI_HCD && (SSB = y || SSB = USB_OHCI_HCD) && EXPERIMENTAL
default n
---help---
Support for the Sonics Silicon Backplane (SSB) attached
Broadcom USB OHCI core.
This device is present in some embedded devices with
Broadcom based SSB bus.
If unsure, say N.
config USB_OHCI_BIG_ENDIAN_DESC
bool
depends on USB_OHCI_HCD
default n
config USB_OHCI_BIG_ENDIAN_MMIO
bool
depends on USB_OHCI_HCD
default n
config USB_OHCI_LITTLE_ENDIAN
bool
depends on USB_OHCI_HCD
default n if STB03xxx || PPC_MPC52xx
default y
config USB_UHCI_HCD
tristate "UHCI HCD (most Intel and VIA) support"
depends on USB && PCI
---help---
The Universal Host Controller Interface is a standard by Intel for
accessing the USB hardware in the PC (which is also called the USB
host controller). If your USB host controller conforms to this
standard, you may want to say Y, but see below. All recent boards
with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
i810, i820) conform to this standard. Also all VIA PCI chipsets
(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
133). If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called uhci-hcd.
config USB_U132_HCD
tristate "Elan U132 Adapter Host Controller"
depends on USB && USB_FTDI_ELAN
default M
help
The U132 adapter is a USB to CardBus adapter specifically designed
for PC cards that contain an OHCI host controller. Typical PC cards
are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
adapter will *NOT* work with PC cards that do not contain an OHCI
controller.
For those PC cards that contain multiple OHCI controllers only the
first one is used.
The driver consists of two modules, the "ftdi-elan" module is a
USB client driver that interfaces to the FTDI chip within ELAN's
USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
controller driver that talks to the OHCI controller within the
CardBus cards that are inserted in the U132 adapter.
This driver has been tested with a CardBus OHCI USB adapter, and
worked with a USB PEN Drive inserted into the first USB port of
the PCCARD. A rather pointless thing to do, but useful for testing.
It is safe to say M here.
See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
config USB_SL811_HCD
tristate "SL811HS HCD support"
depends on USB
help
The SL811HS is a single-port USB controller that supports either
host side or peripheral side roles. Enable this option if your
board has this chip, and you want to use it as a host controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called sl811-hcd.
config USB_SL811_CS
tristate "CF/PCMCIA support for SL811HS HCD"
depends on USB_SL811_HCD && PCMCIA
help
Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
REX-CFU1U CF card (often used with PDAs). If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called "sl811_cs".
config USB_R8A66597_HCD
tristate "R8A66597 HCD support"
depends on USB
help
The R8A66597 is a USB 2.0 host and peripheral controller.
Enable this option if your board has this chip, and you want
to use it as a host controller. If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called r8a66597-hcd.
