/* $Id: su.c,v 1.55 2002/01/08 16:00:16 davem Exp $
* su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
*
* Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
* Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com)
*
* This is mainly a variation of 8250.c, credits go to authors mentioned
* therein. In fact this driver should be merged into the generic 8250.c
* infrastructure perhaps using a 8250_sparc.c module.
*
* Fixed to use tty_get_baud_rate().
* Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
*
* Converted to new 2.5.x UART layer.
* David S. Miller (davem@davemloft.net), 2002-Jul-29
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/spinlock.h>
#include <linux/errno.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/circ_buf.h>
#include <linux/serial.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#ifdef CONFIG_SERIO
#include <linux/serio.h>
#endif
#include <linux/serial_reg.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/prom.h>
#include <asm/of_device.h>
#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#include "suncore.h"
/* We are on a NS PC87303 clocked with 24.0 MHz, which results
* in a UART clock of 1.8462 MHz.
*/
#define SU_BASE_BAUD (1846200 / 16)
enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
/*
* Here we define the default xmit fifo size used for each type of UART.
*/
static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
{ "unknown", 1, 0 },
{ "8250", 1, 0 },
{ "16450", 1, 0 },
{ "16550", 1, 0 },
{ "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
{ "Cirrus", 1, 0 },
{ "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
{ "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
{ "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO },
{ "Startech", 1, 0 },
{ "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO },
{ "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
{ "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
{ "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO }
};
struct uart_sunsu_port {
struct uart_port port;
unsigned char acr;
unsigned char ier;
unsigned short rev;
unsigned char lcr;
unsigned int lsr_break_flag;
unsigned int cflag;
/* Probing information. */
enum su_type su_type;
unsigned int type_probed; /* XXX Stupid */
unsigned long reg_size;
#ifdef CONFIG_SERIO
struct serio serio;
int serio_open;
#endif
};
static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
{
offset <<= up->port.regshift;
switch (up->port.iotype) {
case UPIO_HUB6:
outb(up->port.hub6 - 1 + offset, up->port.iobase);
return inb(up->port.iobase + 1);
case UPIO_MEM:
return readb(up->port.membase + offset);
default:
return inb(up->port.iobase + offset);
}
}
static void serial_out(struct uart_sunsu_port *up, int offset, int value)
{
#ifndef CONFIG_SPARC64
/*
* MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
* connected with a gate then go to SlavIO. When IRQ4 goes tristated
* gate outputs a logical one. Since we use level triggered interrupts
* we have lockup and watchdog reset. We cannot mask IRQ because
* keyboard shares IRQ with us (Word has it as Bob Smelik's design).
* This problem is similar to what Alpha people suffer, see serial.c.
*/
if (offset == UART_MCR)
value |= UART_MCR_OUT2;
#endif
offset <<= up->port.regshift;
switch (up->port.iotype) {
case UPIO_HUB6:
outb(up->port.hub6 - 1 + offset, up->port.iobase);
outb(value, up->port.iobase + 1);
break;
case UPIO_MEM:
writeb(value, up->port.membase + offset);
break;
default:
outb(value, up->port.iobase + offset);
}
}
/*
* We used to support using pause I/O for certain machines. We
* haven't supported this for a while, but just in case it's badly
* needed for certain old 386 machines, I've left these #define's
* in....
*/
#define serial_inp(up, offset) serial_in(up, offset)
#define serial_outp(up, offset, value) serial_out(up, offset, value)
/*
* For the 16C950
*/
static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
{
serial_out(up, UART_SCR, offset);
serial_out(up, UART_ICR, value);
}
#if 0 /* Unused currently */
static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
{
unsigned int value;
serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
serial_out(up, UART_SCR, offset);
value = serial_in(up, UART_ICR);
serial_icr_write(up, UART_ACR, up->acr);
return value;
}
#endif
#ifdef CONFIG_SERIAL_8250_RSA
/*
* Attempts to turn on the RSA FIFO. Returns zero on failure.
* We set the port uart clock rate if we succeed.
*/
static int __enable_rsa(struct uart_sunsu_port *up)
{
unsigned char mode;
int result;
mode = serial_inp(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
if (!result) {
serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
mode = serial_inp(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
}
if (result)
up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
return result;
}
static void enable_rsa(struct uart_sunsu_port *up)
{
if (up->port.type == PORT_RSA) {
if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
spin_lock_irq(&up->port.lock);
__enable_rsa(up);
spin_unlock_irq(&up->port.lock);
}
if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
serial_outp(up, UART_RSA_FRR, 0);
}
}
/*
* Attempts to turn off the RSA FIFO. Returns zero on failure.
* It is unknown why interrupts were disabled in here. However,
* the caller is expected to preserve this behaviour by grabbing
* the spinlock before calling this function.
*/
static void disable_rsa(struct uart_sunsu_port *up)
{
unsigned char mode;
int result;
if (up->port.type == PORT_RSA &&
up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
spin_lock_irq(&up->port.lock);
mode = serial_inp(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
if (!result) {
serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
mode = serial_inp(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
}
if (result)
up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
spin_unlock_irq(&up->port.lock);
}
}
#endif /* CONFIG_SERIAL_8250_RSA */
static inline void __stop_tx(struct uart_sunsu_port *p)
{
if (p->ier & UART_IER_THRI) {
p->ier &= ~UART_IER_THRI;
serial_out(p, UART_IER, p->ier);
}
}
static void sunsu_stop_tx(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
__stop_tx(up);
/*
* We really want to stop the transmitter from sending.
*/
if (up->port.type == PORT_16C950) {
up->acr |= UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
}
static void sunsu_start_tx(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
if (!(up->ier & UART_IER_THRI)) {
up->ier |= UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
/*
* Re-enable the transmitter if we disabled it.
*/
if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
up->acr &= ~UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
}
static void sunsu_stop_rx(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
up->ier &= ~UART_IER_RLSI;
up->port.read_status_mask &= ~UART_LSR_DR;
serial_out(up, UART_IER, up->ier);
}
static void sunsu_enable_ms(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static struct tty_struct *
receive_chars(struct uart_sunsu_port *up, unsigned char *status)
{
struct tty_struct *tty = up->port.info->tty;
unsigned char ch, flag;
int max_count = 256;
int saw_console_brk = 0;
do {
ch = serial_inp(up, UART_RX);
flag = TTY_NORMAL;
up->port.icount.rx++;
if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
UART_LSR_FE | UART_LSR_OE))) {
/*
* For statistics only
*/
if (*status & UART_LSR_BI) {
*status &= ~(UART_LSR_FE | UART_LSR_PE);
up->port.icount.brk++;
if (up->port.cons != NULL &&
up->port.line == up->port.cons->index)
saw_console_brk = 1;
/*
* We do the SysRQ and SAK checking
* here because otherwise the break
* may get masked by ignore_status_mask
* or read_status_mask.
*/
if (uart_handle_break(&up->port))
goto ignore_char;
} else if (*status & UART_LSR_PE)
up->port.icount.parity++;
else if (*status & UART_LSR_FE)
up->port.icount.frame++;
if (*status & UART_LSR_OE)
up->port.icount.overrun++;
/*
* Mask off conditions which should be ingored.
*/
*status &= up->port.read_status_mask;
if (up->port.cons != NULL &&
up->port.line == up->port.cons->index) {
/* Recover the break flag from console xmit */
*status |= up->lsr_break_flag;
up->lsr_break_flag = 0;
}
if (*status & UART_LSR_BI) {
flag = TTY_BREAK;
} else if (*status & UART_LSR_PE)
flag = TTY_PARITY;
else if (*status & UART_LSR_FE)
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch))
goto ignore_char;
if ((*status & up->port.ignore_status_mask) == 0)
tty_insert_flip_char(tty, ch, flag);
if (*status & UART_LSR_OE)
/*
* Overrun is special, since it's reported
* immediately, and doesn't affect the current
* character.
*/
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
ignore_char:
*status = serial_inp(up, UART_LSR);
} while ((*status & UART_LSR_DR) && (max_count-- > 0));
if (saw_console_brk)
sun_do_break();
return tty;
}
static void transmit_chars(struct uart_sunsu_port *up)
{
struct circ_buf *xmit = &up->port.info->xmit;
int count;
if (up->port.x_char) {
serial_outp(up, UART_TX, up->port.x_char);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (uart_tx_stopped(&up->port)) {
sunsu_stop_tx(&up->port);
return;
}
if (uart_circ_empty(xmit)) {
__stop_tx(up);
return;
}
count = up->port.fifosize;
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
if (uart_circ_empty(xmit))
__stop_tx(up);
}
static void check_modem_status(struct uart_sunsu_port *up)
{
int status;
status = serial_in(up, UART_MSR);
if ((status & UART_MSR_ANY_DELTA) == 0)
return;
if (status & UART_MSR_TERI)
up->port.icount.rng++;
if (status & UART_MSR_DDSR)
up->port.icount.dsr++;
if (status & UART_MSR_DDCD)
uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
if (status & UART_MSR_DCTS)
uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
wake_up_interruptible(&up->port.info->delta_msr_wait);
}
static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
{
struct uart_sunsu_port *up = dev_id;
unsigned long flags;
unsigned char status;
spin_lock_irqsave(&up->port.lock, flags);
do {
struct tty_struct *tty;
status = serial_inp(up, UART_LSR);
tty = NULL;
if (status & UART_LSR_DR)
tty = receive_chars(up, &status);
check_modem_status(up);
if (status & UART_LSR_THRE)
transmit_chars(up);
spin_unlock_irqrestore(&up->port.lock, flags);
if (tty)
tty_flip_buffer_push(tty);
spin_lock_irqsave(&up->port.lock, flags);
} while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
spin_unlock_irqrestore(&up->port.lock, flags);
return IRQ_HANDLED;
}
/* Separate interrupt handling path for keyboard/mouse ports. */
static void
sunsu_change_speed(struct uart_port *port, unsigned int cflag,
unsigned int iflag, unsigned int quot);
static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
{
unsigned int cur_cflag = up->cflag;
int quot, new_baud;
up->cflag &= ~CBAUD;
up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
quot = up->port.uartclk / (16 * new_baud);
sunsu_change_speed(&up->port, up->cflag, 0, quot);
}
static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
{
do {
unsigned char ch = serial_inp(up, UART_RX);
/* Stop-A is handled by drivers/char/keyboard.c now. */
if (up->su_type == SU_PORT_KBD) {
#ifdef CONFIG_SERIO
serio_interrupt(&up->serio, ch, 0);
#endif
} else if (up->su_type == SU_PORT_MS) {
int ret = suncore_mouse_baud_detection(ch, is_break);
switch (ret) {
case 2:
sunsu_change_mouse_baud(up);
/* fallthru */
case 1:
break;
case 0:
#ifdef CONFIG_SERIO
serio_interrupt(&up->serio, ch, 0);
#endif
break;
};
}
} while (serial_in(up, UART_LSR) & UART_LSR_DR);
}
static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
{
struct uart_sunsu_port *up = dev_id;
if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
unsigned char status = serial_inp(up, UART_LSR);
if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
}
return IRQ_HANDLED;
}
static unsigned int sunsu_tx_empty(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
static unsigned int sunsu_get_mctrl(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned char status;
unsigned int ret;
status = serial_in(up, UART_MSR);
ret = 0;
if (status & UART_MSR_DCD)
ret |= TIOCM_CAR;
if (status & UART_MSR_RI)
ret |= TIOCM_RNG;
if (status & UART_MSR_DSR)
ret |= TIOCM_DSR;
if (status & UART_MSR_CTS)
ret |= TIOCM_CTS;
return ret;
}
static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned char mcr = 0;
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
serial_out(up, UART_MCR, mcr);
}
static void sunsu_break_ctl(struct uart_port *port, int break_state)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
serial_out(up, UART_LCR, up->lcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static int sunsu_startup(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned long flags;
int retval;
if (up->port.type == PORT_16C950) {
/* Wake up and initialize UART */
up->acr = 0;
serial_outp(up, UART_LCR, 0xBF);
serial_outp(up, UART_EFR, UART_EFR_ECB);
serial_outp(up, UART_IER, 0);
serial_outp(up, UART_LCR, 0);
serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
serial_outp(up, UART_LCR, 0xBF);
serial_outp(up, UART_EFR, UART_EFR_ECB);
serial_outp(up, UART_LCR, 0);
}
#ifdef CONFIG_SERIAL_8250_RSA
/*
* If this is an RSA port, see if we can kick it up to the
* higher speed clock.
*/
enable_rsa(up);
#endif
/*
* Clear the FIFO buffers and disable them.
* (they will be reenabled in set_termios())
*/
if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_outp(up, UART_FCR, 0);
}
/*
* Clear the interrupt registers.
*/
(void) serial_inp(up, UART_LSR);
(void) serial_inp(up, UART_RX);
(void) serial_inp(up, UART_IIR);
(void) serial_inp(up, UART_MSR);
/*
* At this point, there's no way the LSR could still be 0xff;
* if it is, then bail out, because there's likely no UART
* here.
*/
if (!(up->port.flags & UPF_BUGGY_UART) &&
(serial_inp(up, UART_LSR) == 0xff)) {
printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
return -ENODEV;
}
if (up->su_type != SU_PORT_PORT) {
retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
IRQF_SHARED, su_typev[up->su_type], up);
} else {
retval = request_irq(up->port.irq, sunsu_serial_interrupt,
IRQF_SHARED, su_typev[up->su_type], up);
}
if (retval) {
printk("su: Cannot register IRQ %d\n", up->port.irq);
return retval;
}
/*
* Now, initialize the UART
*/
serial_outp(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl |= TIOCM_OUT2;
sunsu_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occurring imminently
* anyway, so we don't enable them here.
*/
up->ier = UART_IER_RLSI | UART_IER_RDI;
serial_outp(up, UART_IER, up->ier);
if (up->port.flags & UPF_FOURPORT) {
unsigned int icp;
/*
* Enable interrupts on the AST Fourport board
*/
icp = (up->port.iobase & 0xfe0) | 0x01f;
outb_p(0x80, icp);
(void) inb_p(icp);
}
/*
* And clear the interrupt registers again for luck.
*/
(void) serial_inp(up, UART_LSR);
(void) serial_inp(up, UART_RX);
(void) serial_inp(up, UART_IIR);
(void) serial_inp(up, UART_MSR);
return 0;
}
static void sunsu_shutdown(struct uart_port *port)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned long flags;
/*
* Disable interrupts from this port
*/
up->ier = 0;
serial_outp(up, UART_IER, 0);
spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_FOURPORT) {
/* reset interrupts on the AST Fourport board */
inb((up->port.iobase & 0xfe0) | 0x1f);
up->port.mctrl |= TIOCM_OUT1;
} else
up->port.mctrl &= ~TIOCM_OUT2;
sunsu_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Disable break condition and FIFOs
*/
serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT);
serial_outp(up, UART_FCR, 0);
#ifdef CONFIG_SERIAL_8250_RSA
/*
* Reset the RSA board back to 115kbps compat mode.
*/
disable_rsa(up);
#endif
/*
* Read data port to reset things.
*/
(void) serial_in(up, UART_RX);
free_irq(up->port.irq, up);
}
static void
sunsu_change_speed(struct uart_port *port, unsigned int cflag,
unsigned int iflag, unsigned int quot)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
unsigned char cval, fcr = 0;
unsigned long flags;
switch (cflag & CSIZE) {
case CS5:
cval = 0x00;
break;
case CS6:
cval = 0x01;
break;
case CS7:
cval = 0x02;
break;
default:
case CS8:
cval = 0x03;
break;
}
if (cflag & CSTOPB)
cval |= 0x04;
if (cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(cflag & PARODD))
cval |= UART_LCR_EPAR;
#ifdef CMSPAR
if (cflag & CMSPAR)
cval |= UART_LCR_SPAR;
#endif
/*
* Work around a bug in the Oxford Semiconductor 952 rev B
* chip which causes it to seriously miscalculate baud rates
* when DLL is 0.
*/
if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
up->rev == 0x5201)
quot ++;
if (uart_config[up->port.type].flags & UART_USE_FIFO) {
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
#ifdef CONFIG_SERIAL_8250_RSA
else if (up->port.type == PORT_RSA)
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
#endif
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
}
if (up->port.type == PORT_16750)
fcr |= UART_FCR7_64BYTE;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characteres to ignore
*/
up->port.ignore_status_mask = 0;
if (iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
if (uart_config[up->port.type].flags & UART_STARTECH) {
serial_outp(up, UART_LCR, 0xBF);
serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
}
serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */
serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */
if (up->port.type == PORT_16750)
serial_outp(up, UART_FCR, fcr); /* set fcr */
serial_outp(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
if (up->port.type != PORT_16750) {
if (fcr & UART_FCR_ENABLE_FIFO) {
/* emulated UARTs (Lucent Venus 167x) need two steps */
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
}
serial_outp(up, UART_FCR, fcr); /* set fcr */
}
up->cflag = cflag;
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void
sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned int baud, quot;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
}
static void sunsu_release_port(struct uart_port *port)
{
}
static int sunsu_request_port(struct uart_port *port)
{
return 0;
}
static void sunsu_config_port(struct uart_port *port, int flags)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
if (flags & UART_CONFIG_TYPE) {
/*
* We are supposed to call autoconfig here, but this requires
* splitting all the OBP probing crap from the UART probing.
* We'll do it when we kill sunsu.c altogether.
*/
port->type = up->type_probed; /* XXX */
}
}
static int
sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
{
return -EINVAL;
}
static const char *
sunsu_type(struct uart_port *port)
{
int type = port->type;
if (type >= ARRAY_SIZE(uart_config))
type = 0;
return uart_config[type].name;
}
static struct uart_ops sunsu_pops = {
.tx_empty = sunsu_tx_empty,
.set_mctrl = sunsu_set_mctrl,
.get_mctrl = sunsu_get_mctrl,
.stop_tx = sunsu_stop_tx,
.start_tx = sunsu_start_tx,
.stop_rx = sunsu_stop_rx,
.enable_ms = sunsu_enable_ms,
.break_ctl = sunsu_break_ctl,
.startup = sunsu_startup,
.shutdown = sunsu_shutdown,
.set_termios = sunsu_set_termios,
.type = sunsu_type,
.release_port = sunsu_release_port,
.request_port = sunsu_request_port,
.config_port = sunsu_config_port,
.verify_port = sunsu_verify_port,
};
#define UART_NR 4
static struct uart_sunsu_port sunsu_ports[UART_NR];
#ifdef CONFIG_SERIO
static DEFINE_SPINLOCK(sunsu_serio_lock);
static int sunsu_serio_write(struct serio *serio, unsigned char ch)
{
struct uart_sunsu_port *up = serio->port_data;
unsigned long flags;
int lsr;
spin_lock_irqsave(&sunsu_serio_lock, flags);
do {
lsr = serial_in(up, UART_LSR);
} while (!(lsr & UART_LSR_THRE));
/* Send the character out. */
serial_out(up, UART_TX, ch);
spin_unlock_irqrestore(&sunsu_serio_lock, flags);
return 0;
}
static int sunsu_serio_open(struct serio *serio)
{
struct uart_sunsu_port *up = serio->port_data;
unsigned long flags;
int ret;
spin_lock_irqsave(&sunsu_serio_lock, flags);
if (!up->serio_open) {
up->serio_open = 1;
ret = 0;
} else
ret = -EBUSY;
spin_unlock_irqrestore(&sunsu_serio_lock, flags);
return ret;
}
static void sunsu_serio_close(struct serio *serio)
{
struct uart_sunsu_port *up = serio->port_data;
unsigned long flags;
spin_lock_irqsave(&sunsu_serio_lock, flags);
up->serio_open = 0;
spin_unlock_irqrestore(&sunsu_serio_lock, flags);
}
#endif /* CONFIG_SERIO */
static void sunsu_autoconfig(struct uart_sunsu_port *up)
{
unsigned char status1, status2, scratch, scratch2, scratch3;
unsigned char save_lcr, save_mcr;
unsigned long flags;
if (up->su_type == SU_PORT_NONE)
return;
up->type_probed = PORT_UNKNOWN;
up->port.iotype = UPIO_MEM;
spin_lock_irqsave(&up->port.lock, flags);
if (!(up->port.flags & UPF_BUGGY_UART)) {
/*
* Do a simple existence test first; if we fail this, there's
* no point trying anything else.
*
* 0x80 is used as a nonsense port to prevent against false
* positives due to ISA bus float. The assumption is that
* 0x80 is a non-existent port; which should be safe since
* include/asm/io.h also makes this assumption.
*/
scratch = serial_inp(up, UART_IER);
serial_outp(up, UART_IER, 0);
#ifdef __i386__
outb(0xff, 0x080);
#endif
scratch2 = serial_inp(up, UART_IER);
serial_outp(up, UART_IER, 0x0f);
#ifdef __i386__
outb(0, 0x080);
#endif
scratch3 = serial_inp(up, UART_IER);
serial_outp(up, UART_IER, scratch);
if (scratch2 != 0 || scratch3 != 0x0F)
goto out; /* We failed; there's nothing here */
}
save_mcr = serial_in(up, UART_MCR);
save_lcr = serial_in(up, UART_LCR);
/*
* Check to see if a UART is really there. Certain broken
* internal modems based on the Rockwell chipset fail this
* test, because they apparently don't implement the loopback
* test mode. So this test is skipped on the COM 1 through
* COM 4 ports. This *should* be safe, since no board
* manufacturer would be stupid enough to design a board
* that conflicts with COM 1-4 --- we hope!
*/
if (!(up->port.flags & UPF_SKIP_TEST)) {
serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
status1 = serial_inp(up, UART_MSR) & 0xF0;
serial_outp(up, UART_MCR, save_mcr);
if (status1 != 0x90)
goto out; /* We failed loopback test */
}
serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */
serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */
serial_outp(up, UART_LCR, 0);
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
scratch = serial_in(up, UART_IIR) >> 6;
switch (scratch) {
case 0:
up->port.type = PORT_16450;
break;
case 1:
up->port.type = PORT_UNKNOWN;
break;
case 2:
up->port.type = PORT_16550;
break;
case 3:
up->port.type = PORT_16550A;
break;
}
if (up->port.type == PORT_16550A) {
/* Check for Startech UART's */
serial_outp(up, UART_LCR, UART_LCR_DLAB);
if (serial_in(up, UART_EFR) == 0) {
up->port.type = PORT_16650;
} else {
serial_outp(up, UART_LCR, 0xBF);
if (serial_in(up, UART_EFR) == 0)
up->port.type = PORT_16650V2;
}
}
if (up->port.type == PORT_16550A) {
/* Check for TI 16750 */
serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
serial_outp(up, UART_FCR,
UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
scratch = serial_in(up, UART_IIR) >> 5;
if (scratch == 7) {
/*
* If this is a 16750, and not a cheap UART
* clone, then it should only go into 64 byte
* mode if the UART_FCR7_64BYTE bit was set
* while UART_LCR_DLAB was latched.
*/
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_outp(up, UART_LCR, 0);
serial_outp(up, UART_FCR,
UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
scratch = serial_in(up, UART_IIR) >> 5;
if (scratch == 6)
up->port.type = PORT_16750;
}
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
}
serial_outp(up, UART_LCR, save_lcr);
if (up->port.type == PORT_16450) {
scratch = serial_in(up, UART_SCR);
serial_outp(up, UART_SCR, 0xa5);
status1 = serial_in(up, UART_SCR);
serial_outp(up, UART_SCR, 0x5a);
status2 = serial_in(up, UART_SCR);
serial_outp(up, UART_SCR, scratch);
if ((status1 != 0xa5) || (status2 != 0x5a))
up->port.type = PORT_8250;
}
up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
if (up->port.type == PORT_UNKNOWN)
goto out;
up->type_probed = up->port.type; /* XXX */
/*
* Reset the UART.
*/
#ifdef CONFIG_SERIAL_8250_RSA
if (up->port.type == PORT_RSA)
serial_outp(up, UART_RSA_FRR, 0);
#endif
serial_outp(up, UART_MCR, save_mcr);
serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT));
serial_outp(up, UART_FCR, 0);
(void)serial_in(up, UART_RX);
serial_outp(up, UART_IER, 0);
out:
spin_unlock_irqrestore(&up->port.lock, flags);
}
static struct uart_driver sunsu_reg = {
.owner = THIS_MODULE,
.driver_name = "serial",
.dev_name = "ttyS",
.major = TTY_MAJOR,
};
static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up)
{
int quot, baud;
#ifdef CONFIG_SERIO
struct serio *serio;
#endif
if (up->su_type == SU_PORT_KBD) {
up->cflag = B1200 | CS8 | CLOCAL | CREAD;
baud = 1200;
} else {
up->cflag = B4800 | CS8 | CLOCAL | CREAD;
baud = 4800;
}
quot = up->port.uartclk / (16 * baud);
sunsu_autoconfig(up);
if (up->port.type == PORT_UNKNOWN)
return -ENODEV;
printk("%s: %s port at %llx, irq %u\n",
to_of_device(up->port.dev)->node->full_name,
(up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
(unsigned long long) up->port.mapbase,
up->port.irq);
#ifdef CONFIG_SERIO
serio = &up->serio;
serio->port_data = up;
serio->id.type = SERIO_RS232;
if (up->su_type == SU_PORT_KBD) {
serio->id.proto = SERIO_SUNKBD;
strlcpy(serio->name, "sukbd", sizeof(serio->name));
} else {
serio->id.proto = SERIO_SUN;
serio->id.extra = 1;
strlcpy(serio->name, "sums", sizeof(serio->name));
}
strlcpy(serio->phys,
(!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
sizeof(serio->phys));
serio->write = sunsu_serio_write;
serio->open = sunsu_serio_open;
serio->close = sunsu_serio_close;
serio->dev.parent = up->port.dev;
serio_register_port(serio);
#endif
sunsu_change_speed(&up->port, up->cflag, 0, quot);
sunsu_startup(&up->port);
return 0;
}
/*
* ------------------------------------------------------------
* Serial console driver
* ------------------------------------------------------------
*/
#ifdef CONFIG_SERIAL_SUNSU_CONSOLE
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/*
* Wait for transmitter & holding register to empty
*/
static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
{
unsigned int status, tmout = 10000;
/* Wait up to 10ms for the character(s) to be sent. */
do {
status = serial_in(up, UART_LSR);
if (status & UART_LSR_BI)
up->lsr_break_flag = UART_LSR_BI;
if (--tmout == 0)
break;
udelay(1);
} while ((status & BOTH_EMPTY) != BOTH_EMPTY);
/* Wait up to 1s for flow control if necessary */
if (up->port.flags & UPF_CONS_FLOW) {
tmout = 1000000;
while (--tmout &&
((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
udelay(1);
}
}
static void sunsu_console_putchar(struct uart_port *port, int ch)
{
struct uart_sunsu_port *up = (struct uart_sunsu_port *)port;
wait_for_xmitr(up);
serial_out(up, UART_TX, ch);
}
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*/
static void sunsu_console_write(struct console *co, const char *s,
unsigned int count)
{
struct uart_sunsu_port *up = &sunsu_ports[co->index];
unsigned long flags;
unsigned int ier;
int locked = 1;
local_irq_save(flags);
if (up->port.sysrq) {
locked = 0;
} else if (oops_in_progress) {
locked = spin_trylock(&up->port.lock);
} else
spin_lock(&up->port.lock);
/*
* First save the UER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, 0);
uart_console_write(&up->port, s, count, sunsu_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
if (locked)
spin_unlock(&up->port.lock);
local_irq_restore(flags);
}
/*
* Setup initial baud/bits/parity. We do two things here:
* - construct a cflag setting for the first su_open()
* - initialize the serial port
* Return non-zero if we didn't find a serial port.
*/
static int __init sunsu_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
printk("Console: ttyS%d (SU)\n",
(sunsu_reg.minor - 64) + co->index);
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index >= UART_NR)
co->index = 0;
port = &sunsu_ports[co->index].port;
/*
* Temporary fix.
*/
spin_lock_init(&port->lock);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
return uart_set_options(port, co, baud, parity, bits, flow);
}
static struct console sunsu_console = {
.name = "ttyS",
.write = sunsu_console_write,
.device = uart_console_device,
.setup = sunsu_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &sunsu_reg,
};
/*
* Register console.
*/
static inline struct console *SUNSU_CONSOLE(void)
{
return &sunsu_console;
}
#else
#define SUNSU_CONSOLE() (NULL)
#define sunsu_serial_console_init() do { } while (0)
#endif
static enum su_type __devinit su_get_type(struct device_node *dp)
{
struct device_node *ap = of_find_node_by_path("/aliases");
if (ap) {
const char *keyb = of_get_property(ap, "keyboard", NULL);
const char *ms = of_get_property(ap, "mouse", NULL);
if (keyb) {
if (dp == of_find_node_by_path(keyb))
return SU_PORT_KBD;
}
if (ms) {
if (dp == of_find_node_by_path(ms))
return SU_PORT_MS;
}
}
return SU_PORT_PORT;
}
static int __devinit su_probe(struct of_device *op, const struct of_device_id *match)
{
static int inst;
struct device_node *dp = op->node;
struct uart_sunsu_port *up;
struct resource *rp;
enum su_type type;
int err;
type = su_get_type(dp);
if (type == SU_PORT_PORT) {
if (inst >= UART_NR)
return -EINVAL;
up = &sunsu_ports[inst];
} else {
up = kzalloc(sizeof(*up), GFP_KERNEL);
if (!up)
return -ENOMEM;
}
up->port.line = inst;
spin_lock_init(&up->port.lock);
up->su_type = type;
rp = &op->resource[0];
up->port.mapbase = rp->start;
up->reg_size = (rp->end - rp->start) + 1;
up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
if (!up->port.membase) {
if (type != SU_PORT_PORT)
kfree(up);
return -ENOMEM;
}
up->port.irq = op->irqs[0];
up->port.dev = &op->dev;
up->port.type = PORT_UNKNOWN;
up->port.uartclk = (SU_BASE_BAUD * 16);
err = 0;
if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
err = sunsu_kbd_ms_init(up);
if (err) {
kfree(up);
goto out_unmap;
}
dev_set_drvdata(&op->dev, up);
return 0;
}
up->port.flags |= UPF_BOOT_AUTOCONF;
sunsu_autoconfig(up);
err = -ENODEV;
if (up->port.type == PORT_UNKNOWN)
goto out_unmap;
up->port.ops = &sunsu_pops;
sunserial_console_match(SUNSU_CONSOLE(), dp,
&sunsu_reg, up->port.line);
err = uart_add_one_port(&sunsu_reg, &up->port);
if (err)
goto out_unmap;
dev_set_drvdata(&op->dev, up);
inst++;
return 0;
out_unmap:
of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
return err;
}
static int __devexit su_remove(struct of_device *op)
{
struct uart_sunsu_port *up = dev_get_drvdata(&op->dev);
if (up->su_type == SU_PORT_MS ||
up->su_type == SU_PORT_KBD) {
#ifdef CONFIG_SERIO
serio_unregister_port(&up->serio);
#endif
kfree(up);
} else if (up->port.type != PORT_UNKNOWN) {
uart_remove_one_port(&sunsu_reg, &up->port);
}
if (up->port.membase)
of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
dev_set_drvdata(&op->dev, NULL);
return 0;
}
static struct of_device_id su_match[] = {
{
.name = "su",
},
{
.name = "su_pnp",
},
{
.name = "serial",
.compatible = "su",
},
{},
};
MODULE_DEVICE_TABLE(of, su_match);
static struct of_platform_driver su_driver = {
.name = "su",
.match_table = su_match,
.probe = su_probe,
.remove = __devexit_p(su_remove),
};
static int __init sunsu_init(void)
{
struct device_node *dp;
int err;
int num_uart = 0;
for_each_node_by_name(dp, "su") {
if (su_get_type(dp) == SU_PORT_PORT)
num_uart++;
}
for_each_node_by_name(dp, "su_pnp") {
if (su_get_type(dp) == SU_PORT_PORT)
num_uart++;
}
for_each_node_by_name(dp, "serial") {
if (of_device_is_compatible(dp, "su")) {
if (su_get_type(dp) == SU_PORT_PORT)
num_uart++;
}
}
if (num_uart) {
err = sunserial_register_minors(&sunsu_reg, num_uart);
if (err)
return err;
}
err = of_register_driver(&su_driver, &of_bus_type);
if (err && num_uart)
sunserial_unregister_minors(&sunsu_reg, num_uart);
return err;
}
static void __exit sunsu_exit(void)
{
if (sunsu_reg.nr)
sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
}
module_init(sunsu_init);
module_exit(sunsu_exit);
MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
MODULE_DESCRIPTION("Sun SU serial port driver");
MODULE_VERSION("2.0");
MODULE_LICENSE("GPL");
