/*
** mux.c:
** serial driver for the Mux console found in some PA-RISC servers.
**
** (c) Copyright 2002 Ryan Bradetich
** (c) Copyright 2002 Hewlett-Packard Company
**
** This program is free software; you can redistribute it and/or modify
** it under the terms of the GNU General Public License as published by
** the Free Software Foundation; either version 2 of the License, or
** (at your option) any later version.
**
** This Driver currently only supports the console (port 0) on the MUX.
** Additional work will be needed on this driver to enable the full
** functionality of the MUX.
**
*/
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/serial.h>
#include <linux/console.h>
#include <linux/delay.h> /* for udelay */
#include <linux/device.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/parisc-device.h>
#ifdef CONFIG_MAGIC_SYSRQ
#include <linux/sysrq.h>
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#define MUX_OFFSET 0x800
#define MUX_LINE_OFFSET 0x80
#define MUX_FIFO_SIZE 255
#define MUX_POLL_DELAY (30 * HZ / 1000)
#define IO_DATA_REG_OFFSET 0x3c
#define IO_DCOUNT_REG_OFFSET 0x40
#define MUX_EOFIFO(status) ((status & 0xF000) == 0xF000)
#define MUX_STATUS(status) ((status & 0xF000) == 0x8000)
#define MUX_BREAK(status) ((status & 0xF000) == 0x2000)
#define MUX_NR 256
static unsigned int port_cnt __read_mostly;
struct mux_port {
struct uart_port port;
int enabled;
};
static struct mux_port mux_ports[MUX_NR];
static struct uart_driver mux_driver = {
.owner = THIS_MODULE,
.driver_name = "ttyB",
.dev_name = "ttyB",
.major = MUX_MAJOR,
.minor = 0,
.nr = MUX_NR,
};
static struct timer_list mux_timer;
#define UART_PUT_CHAR(p, c) __raw_writel((c), (p)->membase + IO_DATA_REG_OFFSET)
#define UART_GET_FIFO_CNT(p) __raw_readl((p)->membase + IO_DCOUNT_REG_OFFSET)
/**
* get_mux_port_count - Get the number of available ports on the Mux.
* @dev: The parisc device.
*
* This function is used to determine the number of ports the Mux
* supports. The IODC data reports the number of ports the Mux
* can support, but there are cases where not all the Mux ports
* are connected. This function can override the IODC and
* return the true port count.
*/
static int __init get_mux_port_count(struct parisc_device *dev)
{
int status;
u8 iodc_data[32];
unsigned long bytecnt;
/* If this is the built-in Mux for the K-Class (Eole CAP/MUX),
* we only need to allocate resources for 1 port since the
* other 7 ports are not connected.
*/
if(dev->id.hversion == 0x15)
return 1;
status = pdc_iodc_read(&bytecnt, dev->hpa.start, 0, iodc_data, 32);
BUG_ON(status != PDC_OK);
/* Return the number of ports specified in the iodc data. */
return ((((iodc_data)[4] & 0xf0) >> 4) * 8) + 8;
}
/**
* mux_tx_empty - Check if the transmitter fifo is empty.
* @port: Ptr to the uart_port.
*
* This function test if the transmitter fifo for the port
* described by 'port' is empty. If it is empty, this function
* should return TIOCSER_TEMT, otherwise return 0.
*/
static unsigned int mux_tx_empty(struct uart_port *port)
{
return UART_GET_FIFO_CNT(port) ? 0 : TIOCSER_TEMT;
}
/**
* mux_set_mctrl - Set the current state of the modem control inputs.
* @ports: Ptr to the uart_port.
* @mctrl: Modem control bits.
*
* The Serial MUX does not support CTS, DCD or DSR so this function
* is ignored.
*/
static void mux_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
}
/**
* mux_get_mctrl - Returns the current state of modem control inputs.
* @port: Ptr to the uart_port.
*
* The Serial MUX does not support CTS, DCD or DSR so these lines are
* treated as permanently active.
*/
static unsigned int mux_get_mctrl(struct uart_port *port)
{
return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
}
/**
* mux_stop_tx - Stop transmitting characters.
* @port: Ptr to the uart_port.
*
* The Serial MUX does not support this function.
*/
static void mux_stop_tx(struct uart_port *port)
{
}
/**
* mux_start_tx - Start transmitting characters.
* @port: Ptr to the uart_port.
*
* The Serial Mux does not support this function.
*/
static void mux_start_tx(struct uart_port *port)
{
}
/**
* mux_stop_rx - Stop receiving characters.
* @port: Ptr to the uart_port.
*
* The Serial Mux does not support this function.
*/
static void mux_stop_rx(struct uart_port *port)
{
}
/**
* mux_enable_ms - Enable modum status interrupts.
* @port: Ptr to the uart_port.
*
* The Serial Mux does not support this function.
*/
static void mux_enable_ms(struct uart_port *port)
{
}
/**
* mux_break_ctl - Control the transmitssion of a break signal.
* @port: Ptr to the uart_port.
* @break_state: Raise/Lower the break signal.
*
* The Serial Mux does not support this function.
*/
static void mux_break_ctl(struct uart_port *port, int break_state)
{
}
/**
* mux_write - Write chars to the mux fifo.
* @port: Ptr to the uart_port.
*
* This function writes all the data from the uart buffer to
* the mux fifo.
*/
static void mux_write(struct uart_port *port)
{
int count;
struct circ_buf *xmit = &port->state->xmit;
if(port->x_char) {
UART_PUT_CHAR(port, port->x_char);
port->icount.tx++;
port->x_char = 0;
return;
}
if(uart_circ_empty(xmit) || uart_tx_stopped(port)) {
mux_stop_tx(port);
return;
}
count = (port->fifosize) - UART_GET_FIFO_CNT(port);
do {
UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if(uart_circ_empty(xmit))
break;
} while(--count > 0);
while(UART_GET_FIFO_CNT(port))
udelay(1);
if(uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
if (uart_circ_empty(xmit))
mux_stop_tx(port);
}
/**
* mux_read - Read chars from the mux fifo.
* @port: Ptr to the uart_port.
*
* This reads all available data from the mux's fifo and pushes
* the data to the tty layer.
*/
static void mux_read(struct uart_port *port)
{
int data;
struct tty_struct *tty = port->state->port.tty;
__u32 start_count = port->icount.rx;
while(1) {
data = __raw_readl(port->membase + IO_DATA_REG_OFFSET);
if (MUX_STATUS(data))
continue;
if (MUX_EOFIFO(data))
break;
port->icount.rx++;
if (MUX_BREAK(data)) {
port->icount.brk++;
if(uart_handle_break(port))
continue;
}
if (uart_handle_sysrq_char(port, data & 0xffu))
continue;
tty_insert_flip_char(tty, data & 0xFF, TTY_NORMAL);
}
if (start_count != port->icount.rx) {
tty_flip_buffer_push(tty);
}
}
/**
* mux_startup - Initialize the port.
* @port: Ptr to the uart_port.
*
* Grab any resources needed for this port and start the
* mux timer.
*/
static int mux_startup(struct uart_port *port)
{
mux_ports[port->line].enabled = 1;
return 0;
}
/**
* mux_shutdown - Disable the port.
* @port: Ptr to the uart_port.
*
* Release any resources needed for the port.
*/
static void mux_shutdown(struct uart_port *port)
{
mux_ports[port->line].enabled = 0;
}
/**
* mux_set_termios - Chane port parameters.
* @port: Ptr to the uart_port.
* @termios: new termios settings.
* @old: old termios settings.
*
* The Serial Mux does not support this function.
*/
static void
mux_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
}
/**
* mux_type - Describe the port.
* @port: Ptr to the uart_port.
*
* Return a pointer to a string constant describing the
* specified port.
*/
static const char *mux_type(struct uart_port *port)
{
return "Mux";
}
/**
* mux_release_port - Release memory and IO regions.
* @port: Ptr to the uart_port.
*
* Release any memory and IO region resources currently in use by
* the port.
*/
static void mux_release_port(struct uart_port *port)
{
}
/**
* mux_request_port - Request memory and IO regions.
* @port: Ptr to the uart_port.
*
* Request any memory and IO region resources required by the port.
* If any fail, no resources should be registered when this function
* returns, and it should return -EBUSY on failure.
*/
static int mux_request_port(struct uart_port *port)
{
return 0;
}
/**
* mux_config_port - Perform port autoconfiguration.
* @port: Ptr to the uart_port.
* @type: Bitmask of required configurations.
*
* Perform any autoconfiguration steps for the port. This function is
* called if the UPF_BOOT_AUTOCONF flag is specified for the port.
* [Note: This is required for now because of a bug in the Serial core.
* rmk has already submitted a patch to linus, should be available for
* 2.5.47.]
*/
static void mux_config_port(struct uart_port *port, int type)
{
port->type = PORT_MUX;
}
/**
* mux_verify_port - Verify the port information.
* @port: Ptr to the uart_port.
* @ser: Ptr to the serial information.
*
* Verify the new serial port information contained within serinfo is
* suitable for this port type.
*/
static int mux_verify_port(struct uart_port *port, struct serial_struct *ser)
{
if(port->membase == NULL)
return -EINVAL;
return 0;
}
/**
* mux_drv_poll - Mux poll function.
* @unused: Unused variable
*
* This function periodically polls the Serial MUX to check for new data.
*/
static void mux_poll(unsigned long unused)
{
int i;
for(i = 0; i < port_cnt; ++i) {
if(!mux_ports[i].enabled)
continue;
mux_read(&mux_ports[i].port);
mux_write(&mux_ports[i].port);
}
mod_timer(&mux_timer, jiffies + MUX_POLL_DELAY);
}
#ifdef CONFIG_SERIAL_MUX_CONSOLE
static void mux_console_write(struct console *co, const char *s, unsigned count)
{
/* Wait until the FIFO drains. */
while(UART_GET_FIFO_CNT(&mux_ports[0].port))
udelay(1);
while(count--) {
if(*s == '\n') {
UART_PUT_CHAR(&mux_ports[0].port, '\r');
}
UART_PUT_CHAR(&mux_ports[0].port, *s++);
}
}
static int mux_console_setup(struct console *co, char *options)
{
return 0;
}
struct tty_driver *mux_console_device(struct console *co, int *index)
{
*index = co->index;
return mux_driver.tty_driver;
}
static struct console mux_console = {
.name = "ttyB",
.write = mux_console_write,
.device = mux_console_device,
.setup = mux_console_setup,
.flags = CON_ENABLED | CON_PRINTBUFFER,
.index = 0,
};
#define MUX_CONSOLE &mux_console
#else
#define MUX_CONSOLE NULL
#endif
static struct uart_ops mux_pops = {
.tx_empty = mux_tx_empty,
.set_mctrl = mux_set_mctrl,
.get_mctrl = mux_get_mctrl,
.stop_tx = mux_stop_tx,
.start_tx = mux_start_tx,
.stop_rx = mux_stop_rx,
.enable_ms = mux_enable_ms,
.break_ctl = mux_break_ctl,
.startup = mux_startup,
.shutdown = mux_shutdown,
.set_termios = mux_set_termios,
.type = mux_type,
.release_port = mux_release_port,
.request_port = mux_request_port,
.config_port = mux_config_port,
.verify_port = mux_verify_port,
};
/**
* mux_probe - Determine if the Serial Mux should claim this device.
* @dev: The parisc device.
*
* Deterimine if the Serial Mux should claim this chip (return 0)
* or not (return 1).
*/
static int __init mux_probe(struct parisc_device *dev)
{
int i, status;
int port_count = get_mux_port_count(dev);
printk(KERN_INFO "Serial mux driver (%d ports) Revision: 0.6\n", port_count);
dev_set_drvdata(&dev->dev, (void *)(long)port_count);
request_mem_region(dev->hpa.start + MUX_OFFSET,
port_count * MUX_LINE_OFFSET, "Mux");
if(!port_cnt) {
mux_driver.cons = MUX_CONSOLE;
status = uart_register_driver(&mux_driver);
if(status) {
printk(KERN_ERR "Serial mux: Unable to register driver.\n");
return 1;
}
}
for(i = 0; i < port_count; ++i, ++port_cnt) {
struct uart_port *port = &mux_ports[port_cnt].port;
port->iobase = 0;
port->mapbase = dev->hpa.start + MUX_OFFSET +
(i * MUX_LINE_OFFSET);
port->membase = ioremap_nocache(port->mapbase, MUX_LINE_OFFSET);
port->iotype = UPIO_MEM;
port->type = PORT_MUX;
port->irq = NO_IRQ;
port->uartclk = 0;
port->fifosize = MUX_FIFO_SIZE;
port->ops = &mux_pops;
port->flags = UPF_BOOT_AUTOCONF;
port->line = port_cnt;
/* The port->timeout needs to match what is present in
* uart_wait_until_sent in serial_core.c. Otherwise
* the time spent in msleep_interruptable will be very
* long, causing the appearance of a console hang.
*/
port->timeout = HZ / 50;
spin_lock_init(&port->lock);
status = uart_add_one_port(&mux_driver, port);
BUG_ON(status);
}
return 0;
}
static int __devexit mux_remove(struct parisc_device *dev)
{
int i, j;
int port_count = (long)dev_get_drvdata(&dev->dev);
/* Find Port 0 for this card in the mux_ports list. */
for(i = 0; i < port_cnt; ++i) {
if(mux_ports[i].port.mapbase == dev->hpa.start + MUX_OFFSET)
break;
}
BUG_ON(i + port_count > port_cnt);
/* Release the resources associated with each port on the device. */
for(j = 0; j < port_count; ++j, ++i) {
struct uart_port *port = &mux_ports[i].port;
uart_remove_one_port(&mux_driver, port);
if(port->membase)
iounmap(port->membase);
}
release_mem_region(dev->hpa.start + MUX_OFFSET, port_count * MUX_LINE_OFFSET);
return 0;
}
/* Hack. This idea was taken from the 8250_gsc.c on how to properly order
* the serial port detection in the proper order. The idea is we always
* want the builtin mux to be detected before addin mux cards, so we
* specifically probe for the builtin mux cards first.
*
* This table only contains the parisc_device_id of known builtin mux
* devices. All other mux cards will be detected by the generic mux_tbl.
*/
static struct parisc_device_id builtin_mux_tbl[] = {
{ HPHW_A_DIRECT, HVERSION_REV_ANY_ID, 0x15, 0x0000D }, /* All K-class */
{ HPHW_A_DIRECT, HVERSION_REV_ANY_ID, 0x44, 0x0000D }, /* E35, E45, and E55 */
{ 0, }
};
static struct parisc_device_id mux_tbl[] = {
{ HPHW_A_DIRECT, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0000D },
{ 0, }
};
MODULE_DEVICE_TABLE(parisc, builtin_mux_tbl);
MODULE_DEVICE_TABLE(parisc, mux_tbl);
static struct parisc_driver builtin_serial_mux_driver = {
.name = "builtin_serial_mux",
.id_table = builtin_mux_tbl,
.probe = mux_probe,
.remove = __devexit_p(mux_remove),
};
static struct parisc_driver serial_mux_driver = {
.name = "serial_mux",
.id_table = mux_tbl,
.probe = mux_probe,
.remove = __devexit_p(mux_remove),
};
/**
* mux_init - Serial MUX initialization procedure.
*
* Register the Serial MUX driver.
*/
static int __init mux_init(void)
{
register_parisc_driver(&builtin_serial_mux_driver);
register_parisc_driver(&serial_mux_driver);
if(port_cnt > 0) {
/* Start the Mux timer */
init_timer(&mux_timer);
mux_timer.function = mux_poll;
mod_timer(&mux_timer, jiffies + MUX_POLL_DELAY);
#ifdef CONFIG_SERIAL_MUX_CONSOLE
register_console(&mux_console);
#endif
}
return 0;
}
/**
* mux_exit - Serial MUX cleanup procedure.
*
* Unregister the Serial MUX driver from the tty layer.
*/
static void __exit mux_exit(void)
{
/* Delete the Mux timer. */
if(port_cnt > 0) {
del_timer(&mux_timer);
#ifdef CONFIG_SERIAL_MUX_CONSOLE
unregister_console(&mux_console);
#endif
}
unregister_parisc_driver(&builtin_serial_mux_driver);
unregister_parisc_driver(&serial_mux_driver);
uart_unregister_driver(&mux_driver);
}
module_init(mux_init);
module_exit(mux_exit);
MODULE_AUTHOR("Ryan Bradetich");
MODULE_DESCRIPTION("Serial MUX driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS_CHARDEV_MAJOR(MUX_MAJOR);
