/*
* Driver for Zilog serial chips found on SGI workstations and
* servers. This driver could actually be made more generic.
*
* This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
* old drivers/sgi/char/sgiserial.c code which itself is based of the original
* drivers/sbus/char/zs.c code. A lot of code has been simply moved over
* directly from there but much has been rewritten. Credits therefore go out
* to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
* for their work there.
*
* Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
* Copyright (C) 2002 David S. Miller (davem@redhat.com)
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/circ_buf.h>
#include <linux/serial.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#include <linux/spinlock.h>
#include <linux/init.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/sgialib.h>
#include <asm/sgi/ioc.h>
#include <asm/sgi/hpc3.h>
#include <asm/sgi/ip22.h>
#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#include "ip22zilog.h"
void ip22_do_break(void);
/*
* On IP22 we need to delay after register accesses but we do not need to
* flush writes.
*/
#define ZSDELAY() udelay(5)
#define ZSDELAY_LONG() udelay(20)
#define ZS_WSYNC(channel) do { } while (0)
#define NUM_IP22ZILOG 1
#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
#define ZS_CLOCK 3672000 /* Zilog input clock rate. */
#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
/*
* We wrap our port structure around the generic uart_port.
*/
struct uart_ip22zilog_port {
struct uart_port port;
/* IRQ servicing chain. */
struct uart_ip22zilog_port *next;
/* Current values of Zilog write registers. */
unsigned char curregs[NUM_ZSREGS];
unsigned int flags;
#define IP22ZILOG_FLAG_IS_CONS 0x00000004
#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
unsigned int cflag;
/* L1-A keyboard break state. */
int kbd_id;
int l1_down;
unsigned char parity_mask;
unsigned char prev_status;
};
#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
(UART_ZILOG(PORT)->curregs[REGNUM])
#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
/* Reading and writing Zilog8530 registers. The delays are to make this
* driver work on the IP22 which needs a settling delay after each chip
* register access, other machines handle this in hardware via auxiliary
* flip-flops which implement the settle time we do in software.
*
* The port lock must be held and local IRQs must be disabled
* when {read,write}_zsreg is invoked.
*/
static unsigned char read_zsreg(struct zilog_channel *channel,
unsigned char reg)
{
unsigned char retval;
writeb(reg, &channel->control);
ZSDELAY();
retval = readb(&channel->control);
ZSDELAY();
return retval;
}
static void write_zsreg(struct zilog_channel *channel,
unsigned char reg, unsigned char value)
{
writeb(reg, &channel->control);
ZSDELAY();
writeb(value, &channel->control);
ZSDELAY();
}
static void ip22zilog_clear_fifo(struct zilog_channel *channel)
{
int i;
for (i = 0; i < 32; i++) {
unsigned char regval;
regval = readb(&channel->control);
ZSDELAY();
if (regval & Rx_CH_AV)
break;
regval = read_zsreg(channel, R1);
readb(&channel->data);
ZSDELAY();
if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
}
}
/* This function must only be called when the TX is not busy. The UART
* port lock must be held and local interrupts disabled.
*/
static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
{
int i;
/* Let pending transmits finish. */
for (i = 0; i < 1000; i++) {
unsigned char stat = read_zsreg(channel, R1);
if (stat & ALL_SNT)
break;
udelay(100);
}
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
ip22zilog_clear_fifo(channel);
/* Disable all interrupts. */
write_zsreg(channel, R1,
regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
/* Set parity, sync config, stop bits, and clock divisor. */
write_zsreg(channel, R4, regs[R4]);
/* Set misc. TX/RX control bits. */
write_zsreg(channel, R10, regs[R10]);
/* Set TX/RX controls sans the enable bits. */
write_zsreg(channel, R3, regs[R3] & ~RxENAB);
write_zsreg(channel, R5, regs[R5] & ~TxENAB);
/* Synchronous mode config. */
write_zsreg(channel, R6, regs[R6]);
write_zsreg(channel, R7, regs[R7]);
/* Don't mess with the interrupt vector (R2, unused by us) and
* master interrupt control (R9). We make sure this is setup
* properly at probe time then never touch it again.
*/
/* Disable baud generator. */
write_zsreg(channel, R14, regs[R14] & ~BRENAB);
/* Clock mode control. */
write_zsreg(channel, R11, regs[R11]);
/* Lower and upper byte of baud rate generator divisor. */
write_zsreg(channel, R12, regs[R12]);
write_zsreg(channel, R13, regs[R13]);
/* Now rewrite R14, with BRENAB (if set). */
write_zsreg(channel, R14, regs[R14]);
/* External status interrupt control. */
write_zsreg(channel, R15, regs[R15]);
/* Reset external status interrupts. */
write_zsreg(channel, R0, RES_EXT_INT);
write_zsreg(channel, R0, RES_EXT_INT);
/* Rewrite R3/R5, this time without enables masked. */
write_zsreg(channel, R3, regs[R3]);
write_zsreg(channel, R5, regs[R5]);
/* Rewrite R1, this time without IRQ enabled masked. */
write_zsreg(channel, R1, regs[R1]);
}
/* Reprogram the Zilog channel HW registers with the copies found in the
* software state struct. If the transmitter is busy, we defer this update
* until the next TX complete interrupt. Else, we do it right now.
*
* The UART port lock must be held and local interrupts disabled.
*/
static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
struct zilog_channel *channel)
{
if (!ZS_REGS_HELD(up)) {
if (ZS_TX_ACTIVE(up)) {
up->flags |= IP22ZILOG_FLAG_REGS_HELD;
} else {
__load_zsregs(channel, up->curregs);
}
}
}
static void ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
struct zilog_channel *channel,
struct pt_regs *regs)
{
struct tty_struct *tty = up->port.info->tty; /* XXX info==NULL? */
while (1) {
unsigned char ch, r1, flag;
r1 = read_zsreg(channel, R1);
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
ch = readb(&channel->control);
ZSDELAY();
/* This funny hack depends upon BRK_ABRT not interfering
* with the other bits we care about in R1.
*/
if (ch & BRK_ABRT)
r1 |= BRK_ABRT;
ch = readb(&channel->data);
ZSDELAY();
ch &= up->parity_mask;
if (ZS_IS_CONS(up) && (r1 & BRK_ABRT)) {
/* Wait for BREAK to deassert to avoid potentially
* confusing the PROM.
*/
while (1) {
ch = readb(&channel->control);
ZSDELAY();
if (!(ch & BRK_ABRT))
break;
}
ip22_do_break();
return;
}
/* A real serial line, record the character and status. */
flag = TTY_NORMAL;
up->port.icount.rx++;
if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
if (r1 & BRK_ABRT) {
r1 &= ~(PAR_ERR | CRC_ERR);
up->port.icount.brk++;
if (uart_handle_break(&up->port))
goto next_char;
}
else if (r1 & PAR_ERR)
up->port.icount.parity++;
else if (r1 & CRC_ERR)
up->port.icount.frame++;
if (r1 & Rx_OVR)
up->port.icount.overrun++;
r1 &= up->port.read_status_mask;
if (r1 & BRK_ABRT)
flag = TTY_BREAK;
else if (r1 & PAR_ERR)
flag = TTY_PARITY;
else if (r1 & CRC_ERR)
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch, regs))
goto next_char;
if (up->port.ignore_status_mask == 0xff ||
(r1 & up->port.ignore_status_mask) == 0)
tty_insert_flip_char(tty, ch, flag);
if (r1 & Rx_OVR)
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
next_char:
ch = readb(&channel->control);
ZSDELAY();
if (!(ch & Rx_CH_AV))
break;
}
tty_flip_buffer_push(tty);
}
static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
struct zilog_channel *channel,
struct pt_regs *regs)
{
unsigned char status;
status = readb(&channel->control);
ZSDELAY();
writeb(RES_EXT_INT, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (ZS_WANTS_MODEM_STATUS(up)) {
if (status & SYNC)
up->port.icount.dsr++;
/* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
* But it does not tell us which bit has changed, we have to keep
* track of this ourselves.
*/
if ((status & DCD) ^ up->prev_status)
uart_handle_dcd_change(&up->port,
(status & DCD));
if ((status & CTS) ^ up->prev_status)
uart_handle_cts_change(&up->port,
(status & CTS));
wake_up_interruptible(&up->port.info->delta_msr_wait);
}
up->prev_status = status;
}
static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
struct zilog_channel *channel)
{
struct circ_buf *xmit;
if (ZS_IS_CONS(up)) {
unsigned char status = readb(&channel->control);
ZSDELAY();
/* TX still busy? Just wait for the next TX done interrupt.
*
* It can occur because of how we do serial console writes. It would
* be nice to transmit console writes just like we normally would for
* a TTY line. (ie. buffered and TX interrupt driven). That is not
* easy because console writes cannot sleep. One solution might be
* to poll on enough port->xmit space becomming free. -DaveM
*/
if (!(status & Tx_BUF_EMP))
return;
}
up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
if (ZS_REGS_HELD(up)) {
__load_zsregs(channel, up->curregs);
up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
}
if (ZS_TX_STOPPED(up)) {
up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
goto ack_tx_int;
}
if (up->port.x_char) {
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
writeb(up->port.x_char, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (up->port.info == NULL)
goto ack_tx_int;
xmit = &up->port.info->xmit;
if (uart_circ_empty(xmit))
goto ack_tx_int;
if (uart_tx_stopped(&up->port))
goto ack_tx_int;
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
writeb(xmit->buf[xmit->tail], &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
return;
ack_tx_int:
writeb(RES_Tx_P, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_ip22zilog_port *up = dev_id;
while (up) {
struct zilog_channel *channel
= ZILOG_CHANNEL_FROM_PORT(&up->port);
unsigned char r3;
spin_lock(&up->port.lock);
r3 = read_zsreg(channel, R3);
/* Channel A */
if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
writeb(RES_H_IUS, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (r3 & CHARxIP)
ip22zilog_receive_chars(up, channel, regs);
if (r3 & CHAEXT)
ip22zilog_status_handle(up, channel, regs);
if (r3 & CHATxIP)
ip22zilog_transmit_chars(up, channel);
}
spin_unlock(&up->port.lock);
/* Channel B */
up = up->next;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
spin_lock(&up->port.lock);
if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
writeb(RES_H_IUS, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (r3 & CHBRxIP)
ip22zilog_receive_chars(up, channel, regs);
if (r3 & CHBEXT)
ip22zilog_status_handle(up, channel, regs);
if (r3 & CHBTxIP)
ip22zilog_transmit_chars(up, channel);
}
spin_unlock(&up->port.lock);
up = up->next;
}
return IRQ_HANDLED;
}
/* A convenient way to quickly get R0 status. The caller must _not_ hold the
* port lock, it is acquired here.
*/
static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
{
struct zilog_channel *channel;
unsigned char status;
channel = ZILOG_CHANNEL_FROM_PORT(port);
status = readb(&channel->control);
ZSDELAY();
return status;
}
/* The port lock is not held. */
static unsigned int ip22zilog_tx_empty(struct uart_port *port)
{
unsigned long flags;
unsigned char status;
unsigned int ret;
spin_lock_irqsave(&port->lock, flags);
status = ip22zilog_read_channel_status(port);
spin_unlock_irqrestore(&port->lock, flags);
if (status & Tx_BUF_EMP)
ret = TIOCSER_TEMT;
else
ret = 0;
return ret;
}
/* The port lock is held and interrupts are disabled. */
static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
{
unsigned char status;
unsigned int ret;
status = ip22zilog_read_channel_status(port);
ret = 0;
if (status & DCD)
ret |= TIOCM_CAR;
if (status & SYNC)
ret |= TIOCM_DSR;
if (status & CTS)
ret |= TIOCM_CTS;
return ret;
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char set_bits, clear_bits;
set_bits = clear_bits = 0;
if (mctrl & TIOCM_RTS)
set_bits |= RTS;
else
clear_bits |= RTS;
if (mctrl & TIOCM_DTR)
set_bits |= DTR;
else
clear_bits |= DTR;
/* NOTE: Not subject to 'transmitter active' rule. */
up->curregs[R5] |= set_bits;
up->curregs[R5] &= ~clear_bits;
write_zsreg(channel, R5, up->curregs[R5]);
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_stop_tx(struct uart_port *port)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_start_tx(struct uart_port *port)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char status;
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
status = readb(&channel->control);
ZSDELAY();
/* TX busy? Just wait for the TX done interrupt. */
if (!(status & Tx_BUF_EMP))
return;
/* Send the first character to jump-start the TX done
* IRQ sending engine.
*/
if (port->x_char) {
writeb(port->x_char, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
port->icount.tx++;
port->x_char = 0;
} else {
struct circ_buf *xmit = &port->info->xmit;
writeb(xmit->buf[xmit->tail], &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
}
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_stop_rx(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
if (ZS_IS_CONS(up))
return;
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable all RX interrupts. */
up->curregs[R1] &= ~RxINT_MASK;
ip22zilog_maybe_update_regs(up, channel);
}
/* The port lock is held. */
static void ip22zilog_enable_ms(struct uart_port *port)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char new_reg;
new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
if (new_reg != up->curregs[R15]) {
up->curregs[R15] = new_reg;
/* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R15, up->curregs[R15]);
}
}
/* The port lock is not held. */
static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char set_bits, clear_bits, new_reg;
unsigned long flags;
set_bits = clear_bits = 0;
if (break_state)
set_bits |= SND_BRK;
else
clear_bits |= SND_BRK;
spin_lock_irqsave(&port->lock, flags);
new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
if (new_reg != up->curregs[R5]) {
up->curregs[R5] = new_reg;
/* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R5, up->curregs[R5]);
}
spin_unlock_irqrestore(&port->lock, flags);
}
static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
{
struct zilog_channel *channel;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
up->prev_status = readb(&channel->control);
/* Enable receiver and transmitter. */
up->curregs[R3] |= RxENAB;
up->curregs[R5] |= TxENAB;
up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
ip22zilog_maybe_update_regs(up, channel);
}
static int ip22zilog_startup(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
unsigned long flags;
if (ZS_IS_CONS(up))
return 0;
spin_lock_irqsave(&port->lock, flags);
__ip22zilog_startup(up);
spin_unlock_irqrestore(&port->lock, flags);
return 0;
}
/*
* The test for ZS_IS_CONS is explained by the following e-mail:
*****
* From: Russell King <rmk@arm.linux.org.uk>
* Date: Sun, 8 Dec 2002 10:18:38 +0000
*
* On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
* > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
* > and I noticed that something is not right with reference
* > counting in this case. It seems that when the console
* > is open by kernel initially, this is not accounted
* > as an open, and uart_startup is not called.
*
* That is correct. We are unable to call uart_startup when the serial
* console is initialised because it may need to allocate memory (as
* request_irq does) and the memory allocators may not have been
* initialised.
*
* 1. initialise the port into a state where it can send characters in the
* console write method.
*
* 2. don't do the actual hardware shutdown in your shutdown() method (but
* do the normal software shutdown - ie, free irqs etc)
*****
*/
static void ip22zilog_shutdown(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
unsigned long flags;
if (ZS_IS_CONS(up))
return;
spin_lock_irqsave(&port->lock, flags);
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable receiver and transmitter. */
up->curregs[R3] &= ~RxENAB;
up->curregs[R5] &= ~TxENAB;
/* Disable all interrupts and BRK assertion. */
up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
up->curregs[R5] &= ~SND_BRK;
ip22zilog_maybe_update_regs(up, channel);
spin_unlock_irqrestore(&port->lock, flags);
}
/* Shared by TTY driver and serial console setup. The port lock is held
* and local interrupts are disabled.
*/
static void
ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
unsigned int iflag, int brg)
{
up->curregs[R10] = NRZ;
up->curregs[R11] = TCBR | RCBR;
/* Program BAUD and clock source. */
up->curregs[R4] &= ~XCLK_MASK;
up->curregs[R4] |= X16CLK;
up->curregs[R12] = brg & 0xff;
up->curregs[R13] = (brg >> 8) & 0xff;
up->curregs[R14] = BRENAB;
/* Character size, stop bits, and parity. */
up->curregs[3] &= ~RxN_MASK;
up->curregs[5] &= ~TxN_MASK;
switch (cflag & CSIZE) {
case CS5:
up->curregs[3] |= Rx5;
up->curregs[5] |= Tx5;
up->parity_mask = 0x1f;
break;
case CS6:
up->curregs[3] |= Rx6;
up->curregs[5] |= Tx6;
up->parity_mask = 0x3f;
break;
case CS7:
up->curregs[3] |= Rx7;
up->curregs[5] |= Tx7;
up->parity_mask = 0x7f;
break;
case CS8:
default:
up->curregs[3] |= Rx8;
up->curregs[5] |= Tx8;
up->parity_mask = 0xff;
break;
};
up->curregs[4] &= ~0x0c;
if (cflag & CSTOPB)
up->curregs[4] |= SB2;
else
up->curregs[4] |= SB1;
if (cflag & PARENB)
up->curregs[4] |= PAR_ENAB;
else
up->curregs[4] &= ~PAR_ENAB;
if (!(cflag & PARODD))
up->curregs[4] |= PAR_EVEN;
else
up->curregs[4] &= ~PAR_EVEN;
up->port.read_status_mask = Rx_OVR;
if (iflag & INPCK)
up->port.read_status_mask |= CRC_ERR | PAR_ERR;
if (iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= BRK_ABRT;
up->port.ignore_status_mask = 0;
if (iflag & IGNPAR)
up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
if (iflag & IGNBRK) {
up->port.ignore_status_mask |= BRK_ABRT;
if (iflag & IGNPAR)
up->port.ignore_status_mask |= Rx_OVR;
}
if ((cflag & CREAD) == 0)
up->port.ignore_status_mask = 0xff;
}
/* The port lock is not held. */
static void
ip22zilog_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
unsigned long flags;
int baud, brg;
baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
spin_lock_irqsave(&up->port.lock, flags);
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
else
up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
up->cflag = termios->c_cflag;
ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
spin_unlock_irqrestore(&up->port.lock, flags);
}
static const char *ip22zilog_type(struct uart_port *port)
{
return "IP22-Zilog";
}
/* We do not request/release mappings of the registers here, this
* happens at early serial probe time.
*/
static void ip22zilog_release_port(struct uart_port *port)
{
}
static int ip22zilog_request_port(struct uart_port *port)
{
return 0;
}
/* These do not need to do anything interesting either. */
static void ip22zilog_config_port(struct uart_port *port, int flags)
{
}
/* We do not support letting the user mess with the divisor, IRQ, etc. */
static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
{
return -EINVAL;
}
static struct uart_ops ip22zilog_pops = {
.tx_empty = ip22zilog_tx_empty,
.set_mctrl = ip22zilog_set_mctrl,
.get_mctrl = ip22zilog_get_mctrl,
.stop_tx = ip22zilog_stop_tx,
.start_tx = ip22zilog_start_tx,
.stop_rx = ip22zilog_stop_rx,
.enable_ms = ip22zilog_enable_ms,
.break_ctl = ip22zilog_break_ctl,
.startup = ip22zilog_startup,
.shutdown = ip22zilog_shutdown,
.set_termios = ip22zilog_set_termios,
.type = ip22zilog_type,
.release_port = ip22zilog_release_port,
.request_port = ip22zilog_request_port,
.config_port = ip22zilog_config_port,
.verify_port = ip22zilog_verify_port,
};
static struct uart_ip22zilog_port *ip22zilog_port_table;
static struct zilog_layout **ip22zilog_chip_regs;
static struct uart_ip22zilog_port *ip22zilog_irq_chain;
static int zilog_irq = -1;
static void * __init alloc_one_table(unsigned long size)
{
void *ret;
ret = kmalloc(size, GFP_KERNEL);
if (ret != NULL)
memset(ret, 0, size);
return ret;
}
static void __init ip22zilog_alloc_tables(void)
{
ip22zilog_port_table = (struct uart_ip22zilog_port *)
alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
ip22zilog_chip_regs = (struct zilog_layout **)
alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
}
}
/* Get the address of the registers for IP22-Zilog instance CHIP. */
static struct zilog_layout * __init get_zs(int chip)
{
unsigned long base;
if (chip < 0 || chip >= NUM_IP22ZILOG) {
panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
}
/* Not probe-able, hard code it. */
base = (unsigned long) &sgioc->uart;
zilog_irq = SGI_SERIAL_IRQ;
request_mem_region(base, 8, "IP22-Zilog");
return (struct zilog_layout *) base;
}
#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
static void ip22zilog_put_char(struct uart_port *port, int ch)
{
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
int loops = ZS_PUT_CHAR_MAX_DELAY;
/* This is a timed polling loop so do not switch the explicit
* udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
*/
do {
unsigned char val = readb(&channel->control);
if (val & Tx_BUF_EMP) {
ZSDELAY();
break;
}
udelay(5);
} while (--loops);
writeb(ch, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
}
static void
ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
{
struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
uart_console_write(&up->port, s, count, ip22zilog_put_char);
udelay(2);
spin_unlock_irqrestore(&up->port.lock, flags);
}
void
ip22serial_console_termios(struct console *con, char *options)
{
int baud = 9600, bits = 8, cflag;
int parity = 'n';
int flow = 'n';
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
cflag = CREAD | HUPCL | CLOCAL;
switch (baud) {
case 150: cflag |= B150; break;
case 300: cflag |= B300; break;
case 600: cflag |= B600; break;
case 1200: cflag |= B1200; break;
case 2400: cflag |= B2400; break;
case 4800: cflag |= B4800; break;
case 9600: cflag |= B9600; break;
case 19200: cflag |= B19200; break;
case 38400: cflag |= B38400; break;
default: baud = 9600; cflag |= B9600; break;
}
con->cflag = cflag | CS8; /* 8N1 */
}
static int __init ip22zilog_console_setup(struct console *con, char *options)
{
struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
unsigned long flags;
int baud, brg;
printk("Console: ttyS%d (IP22-Zilog)\n", con->index);
/* Get firmware console settings. */
ip22serial_console_termios(con, options);
/* Firmware console speed is limited to 150-->38400 baud so
* this hackish cflag thing is OK.
*/
switch (con->cflag & CBAUD) {
case B150: baud = 150; break;
case B300: baud = 300; break;
case B600: baud = 600; break;
case B1200: baud = 1200; break;
case B2400: baud = 2400; break;
case B4800: baud = 4800; break;
default: case B9600: baud = 9600; break;
case B19200: baud = 19200; break;
case B38400: baud = 38400; break;
};
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
spin_lock_irqsave(&up->port.lock, flags);
up->curregs[R15] = BRKIE;
ip22zilog_convert_to_zs(up, con->cflag, 0, brg);
__ip22zilog_startup(up);
spin_unlock_irqrestore(&up->port.lock, flags);
return 0;
}
static struct uart_driver ip22zilog_reg;
static struct console ip22zilog_console = {
.name = "ttyS",
.write = ip22zilog_console_write,
.device = uart_console_device,
.setup = ip22zilog_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &ip22zilog_reg,
};
#endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
static struct uart_driver ip22zilog_reg = {
.owner = THIS_MODULE,
.driver_name = "serial",
.dev_name = "ttyS",
.major = TTY_MAJOR,
.minor = 64,
.nr = NUM_CHANNELS,
#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
.cons = &ip22zilog_console,
#endif
};
static void __init ip22zilog_prepare(void)
{
struct uart_ip22zilog_port *up;
struct zilog_layout *rp;
int channel, chip;
/*
* Temporary fix.
*/
for (channel = 0; channel < NUM_CHANNELS; channel++)
spin_lock_init(&ip22zilog_port_table[channel].port.lock);
ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1];
up = &ip22zilog_port_table[0];
for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--)
up[channel].next = &up[channel - 1];
up[channel].next = NULL;
for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
if (!ip22zilog_chip_regs[chip]) {
ip22zilog_chip_regs[chip] = rp = get_zs(chip);
up[(chip * 2) + 0].port.membase = (char *) &rp->channelB;
up[(chip * 2) + 1].port.membase = (char *) &rp->channelA;
/* In theory mapbase is the physical address ... */
up[(chip * 2) + 0].port.mapbase =
(unsigned long) ioremap((unsigned long) &rp->channelB, 8);
up[(chip * 2) + 1].port.mapbase =
(unsigned long) ioremap((unsigned long) &rp->channelA, 8);
}
/* Channel A */
up[(chip * 2) + 0].port.iotype = UPIO_MEM;
up[(chip * 2) + 0].port.irq = zilog_irq;
up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
up[(chip * 2) + 0].port.fifosize = 1;
up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
up[(chip * 2) + 0].port.flags = 0;
up[(chip * 2) + 0].port.line = (chip * 2) + 0;
up[(chip * 2) + 0].flags = 0;
/* Channel B */
up[(chip * 2) + 1].port.iotype = UPIO_MEM;
up[(chip * 2) + 1].port.irq = zilog_irq;
up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
up[(chip * 2) + 1].port.fifosize = 1;
up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
up[(chip * 2) + 1].port.line = (chip * 2) + 1;
up[(chip * 2) + 1].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
}
}
static void __init ip22zilog_init_hw(void)
{
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
unsigned long flags;
int baud, brg;
spin_lock_irqsave(&up->port.lock, flags);
if (ZS_IS_CHANNEL_A(up)) {
write_zsreg(channel, R9, FHWRES);
ZSDELAY_LONG();
(void) read_zsreg(channel, R0);
}
/* Normal serial TTY. */
up->parity_mask = 0xff;
up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
up->curregs[R3] = RxENAB | Rx8;
up->curregs[R5] = TxENAB | Tx8;
up->curregs[R9] = NV | MIE;
up->curregs[R10] = NRZ;
up->curregs[R11] = TCBR | RCBR;
baud = 9600;
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
up->curregs[R12] = (brg & 0xff);
up->curregs[R13] = (brg >> 8) & 0xff;
up->curregs[R14] = BRENAB;
__load_zsregs(channel, up->curregs);
/* set master interrupt enable */
write_zsreg(channel, R9, up->curregs[R9]);
spin_unlock_irqrestore(&up->port.lock, flags);
}
}
static int __init ip22zilog_ports_init(void)
{
int ret;
printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
ip22zilog_prepare();
if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
"IP22-Zilog", ip22zilog_irq_chain)) {
panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
}
ip22zilog_init_hw();
ret = uart_register_driver(&ip22zilog_reg);
if (ret == 0) {
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
uart_add_one_port(&ip22zilog_reg, &up->port);
}
}
return ret;
}
static int __init ip22zilog_init(void)
{
/* IP22 Zilog setup is hard coded, no probing to do. */
ip22zilog_alloc_tables();
ip22zilog_ports_init();
return 0;
}
static void __exit ip22zilog_exit(void)
{
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
uart_remove_one_port(&ip22zilog_reg, &up->port);
}
uart_unregister_driver(&ip22zilog_reg);
}
module_init(ip22zilog_init);
module_exit(ip22zilog_exit);
/* David wrote it but I'm to blame for the bugs ... */
MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
MODULE_DESCRIPTION("SGI Zilog serial port driver");
MODULE_LICENSE("GPL");
