/*
* linux/drivers/char/at91_serial.c
*
* Driver for Atmel AT91RM9200 Serial ports
*
* Copyright (C) 2003 Rick Bronson
*
* Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/serial.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/tty_flip.h>
#include <asm/io.h>
#include <asm/arch/at91rm9200_usart.h>
#include <asm/mach/serial_at91rm9200.h>
#include <asm/arch/board.h>
#include <asm/arch/pio.h>
#if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#ifdef CONFIG_SERIAL_AT91_TTYAT
/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
* should coexist with the 8250 driver, such as if we have an external 16C550
* UART. */
#define SERIAL_AT91_MAJOR 204
#define MINOR_START 154
#define AT91_DEVICENAME "ttyAT"
#else
/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
* name, but it is legally reserved for the 8250 driver. */
#define SERIAL_AT91_MAJOR TTY_MAJOR
#define MINOR_START 64
#define AT91_DEVICENAME "ttyS"
#endif
#define AT91_VA_BASE_DBGU ((unsigned long) AT91_VA_BASE_SYS + AT91_DBGU)
#define AT91_ISR_PASS_LIMIT 256
#define UART_PUT_CR(port,v) writel(v, (port)->membase + AT91_US_CR)
#define UART_GET_MR(port) readl((port)->membase + AT91_US_MR)
#define UART_PUT_MR(port,v) writel(v, (port)->membase + AT91_US_MR)
#define UART_PUT_IER(port,v) writel(v, (port)->membase + AT91_US_IER)
#define UART_PUT_IDR(port,v) writel(v, (port)->membase + AT91_US_IDR)
#define UART_GET_IMR(port) readl((port)->membase + AT91_US_IMR)
#define UART_GET_CSR(port) readl((port)->membase + AT91_US_CSR)
#define UART_GET_CHAR(port) readl((port)->membase + AT91_US_RHR)
#define UART_PUT_CHAR(port,v) writel(v, (port)->membase + AT91_US_THR)
#define UART_GET_BRGR(port) readl((port)->membase + AT91_US_BRGR)
#define UART_PUT_BRGR(port,v) writel(v, (port)->membase + AT91_US_BRGR)
#define UART_PUT_RTOR(port,v) writel(v, (port)->membase + AT91_US_RTOR)
// #define UART_GET_CR(port) readl((port)->membase + AT91_US_CR) // is write-only
/* PDC registers */
#define UART_PUT_PTCR(port,v) writel(v, (port)->membase + AT91_PDC_PTCR)
#define UART_PUT_RPR(port,v) writel(v, (port)->membase + AT91_PDC_RPR)
#define UART_PUT_RCR(port,v) writel(v, (port)->membase + AT91_PDC_RCR)
#define UART_GET_RCR(port) readl((port)->membase + AT91_PDC_RCR)
#define UART_PUT_RNPR(port,v) writel(v, (port)->membase + AT91_PDC_RNPR)
#define UART_PUT_RNCR(port,v) writel(v, (port)->membase + AT91_PDC_RNCR)
static int (*at91_open)(struct uart_port *);
static void (*at91_close)(struct uart_port *);
#ifdef SUPPORT_SYSRQ
static struct console at91_console;
#endif
/*
* Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
*/
static u_int at91_tx_empty(struct uart_port *port)
{
return (UART_GET_CSR(port) & AT91_US_TXEMPTY) ? TIOCSER_TEMT : 0;
}
/*
* Set state of the modem control output lines
*/
static void at91_set_mctrl(struct uart_port *port, u_int mctrl)
{
unsigned int control = 0;
/*
* Errata #39: RTS0 is not internally connected to PA21. We need to drive
* the pin manually.
*/
if (port->mapbase == AT91_VA_BASE_US0) {
if (mctrl & TIOCM_RTS)
at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0);
else
at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0);
}
if (mctrl & TIOCM_RTS)
control |= AT91_US_RTSEN;
else
control |= AT91_US_RTSDIS;
if (mctrl & TIOCM_DTR)
control |= AT91_US_DTREN;
else
control |= AT91_US_DTRDIS;
UART_PUT_CR(port,control);
}
/*
* Get state of the modem control input lines
*/
static u_int at91_get_mctrl(struct uart_port *port)
{
unsigned int status, ret = 0;
status = UART_GET_CSR(port);
/*
* The control signals are active low.
*/
if (!(status & AT91_US_DCD))
ret |= TIOCM_CD;
if (!(status & AT91_US_CTS))
ret |= TIOCM_CTS;
if (!(status & AT91_US_DSR))
ret |= TIOCM_DSR;
if (!(status & AT91_US_RI))
ret |= TIOCM_RI;
return ret;
}
/*
* Stop transmitting.
*/
static void at91_stop_tx(struct uart_port *port)
{
UART_PUT_IDR(port, AT91_US_TXRDY);
port->read_status_mask &= ~AT91_US_TXRDY;
}
/*
* Start transmitting.
*/
static void at91_start_tx(struct uart_port *port)
{
port->read_status_mask |= AT91_US_TXRDY;
UART_PUT_IER(port, AT91_US_TXRDY);
}
/*
* Stop receiving - port is in process of being closed.
*/
static void at91_stop_rx(struct uart_port *port)
{
UART_PUT_IDR(port, AT91_US_RXRDY);
}
/*
* Enable modem status interrupts
*/
static void at91_enable_ms(struct uart_port *port)
{
port->read_status_mask |= (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
}
/*
* Control the transmission of a break signal
*/
static void at91_break_ctl(struct uart_port *port, int break_state)
{
if (break_state != 0)
UART_PUT_CR(port, AT91_US_STTBRK); /* start break */
else
UART_PUT_CR(port, AT91_US_STPBRK); /* stop break */
}
/*
* Characters received (called from interrupt handler)
*/
static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs)
{
struct tty_struct *tty = port->info->tty;
unsigned int status, ch, flg;
status = UART_GET_CSR(port) & port->read_status_mask;
while (status & (AT91_US_RXRDY)) {
ch = UART_GET_CHAR(port);
port->icount.rx++;
flg = TTY_NORMAL;
/*
* note that the error handling code is
* out of the main execution path
*/
if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE))) {
UART_PUT_CR(port, AT91_US_RSTSTA); /* clear error */
if (status & (AT91_US_PARE))
port->icount.parity++;
if (status & (AT91_US_FRAME))
port->icount.frame++;
if (status & (AT91_US_OVRE))
port->icount.overrun++;
if (status & AT91_US_PARE)
flg = TTY_PARITY;
else if (status & AT91_US_FRAME)
flg = TTY_FRAME;
if (status & AT91_US_OVRE) {
/*
* overrun does *not* affect the character
* we read from the FIFO
*/
tty_insert_flip_char(tty, ch, flg);
ch = 0;
flg = TTY_OVERRUN;
}
#ifdef SUPPORT_SYSRQ
port->sysrq = 0;
#endif
}
if (uart_handle_sysrq_char(port, ch, regs))
goto ignore_char;
tty_insert_flip_char(tty, ch, flg);
ignore_char:
status = UART_GET_CSR(port) & port->read_status_mask;
}
tty_flip_buffer_push(tty);
}
/*
* Transmit characters (called from interrupt handler)
*/
static void at91_tx_chars(struct uart_port *port)
{
struct circ_buf *xmit = &port->info->xmit;
if (port->x_char) {
UART_PUT_CHAR(port, port->x_char);
port->icount.tx++;
port->x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
at91_stop_tx(port);
return;
}
while (UART_GET_CSR(port) & AT91_US_TXRDY) {
UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if (uart_circ_empty(xmit))
break;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
if (uart_circ_empty(xmit))
at91_stop_tx(port);
}
/*
* Interrupt handler
*/
static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_port *port = dev_id;
unsigned int status, pending, pass_counter = 0;
status = UART_GET_CSR(port);
pending = status & port->read_status_mask;
if (pending) {
do {
if (pending & AT91_US_RXRDY)
at91_rx_chars(port, regs);
/* Clear the relevent break bits */
if (pending & AT91_US_RXBRK) {
UART_PUT_CR(port, AT91_US_RSTSTA);
port->icount.brk++;
uart_handle_break(port);
}
// TODO: All reads to CSR will clear these interrupts!
if (pending & AT91_US_RIIC) port->icount.rng++;
if (pending & AT91_US_DSRIC) port->icount.dsr++;
if (pending & AT91_US_DCDIC)
uart_handle_dcd_change(port, !(status & AT91_US_DCD));
if (pending & AT91_US_CTSIC)
uart_handle_cts_change(port, !(status & AT91_US_CTS));
if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC))
wake_up_interruptible(&port->info->delta_msr_wait);
if (pending & AT91_US_TXRDY)
at91_tx_chars(port);
if (pass_counter++ > AT91_ISR_PASS_LIMIT)
break;
status = UART_GET_CSR(port);
pending = status & port->read_status_mask;
} while (pending);
}
return IRQ_HANDLED;
}
/*
* Perform initialization and enable port for reception
*/
static int at91_startup(struct uart_port *port)
{
int retval;
/*
* Ensure that no interrupts are enabled otherwise when
* request_irq() is called we could get stuck trying to
* handle an unexpected interrupt
*/
UART_PUT_IDR(port, -1);
/*
* Allocate the IRQ
*/
retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port);
if (retval) {
printk("at91_serial: at91_startup - Can't get irq\n");
return retval;
}
/*
* If there is a specific "open" function (to register
* control line interrupts)
*/
if (at91_open) {
retval = at91_open(port);
if (retval) {
free_irq(port->irq, port);
return retval;
}
}
port->read_status_mask = AT91_US_RXRDY | AT91_US_TXRDY | AT91_US_OVRE
| AT91_US_FRAME | AT91_US_PARE | AT91_US_RXBRK;
/*
* Finally, enable the serial port
*/
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); /* enable xmit & rcvr */
UART_PUT_IER(port, AT91_US_RXRDY); /* do receive only */
return 0;
}
/*
* Disable the port
*/
static void at91_shutdown(struct uart_port *port)
{
/*
* Disable all interrupts, port and break condition.
*/
UART_PUT_CR(port, AT91_US_RSTSTA);
UART_PUT_IDR(port, -1);
/*
* Free the interrupt
*/
free_irq(port->irq, port);
/*
* If there is a specific "close" function (to unregister
* control line interrupts)
*/
if (at91_close)
at91_close(port);
}
/*
* Power / Clock management.
*/
static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate)
{
switch (state) {
case 0:
/*
* Enable the peripheral clock for this serial port.
* This is called on uart_open() or a resume event.
*/
at91_sys_write(AT91_PMC_PCER, 1 << port->irq);
break;
case 3:
/*
* Disable the peripheral clock for this serial port.
* This is called on uart_close() or a suspend event.
*/
if (port->irq != AT91_ID_SYS) /* is this a shared clock? */
at91_sys_write(AT91_PMC_PCDR, 1 << port->irq);
break;
default:
printk(KERN_ERR "at91_serial: unknown pm %d\n", state);
}
}
/*
* Change the port parameters
*/
static void at91_set_termios(struct uart_port *port, struct termios * termios, struct termios * old)
{
unsigned long flags;
unsigned int mode, imr, quot, baud;
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
/* Get current mode register */
mode = UART_GET_MR(port) & ~(AT91_US_CHRL | AT91_US_NBSTOP | AT91_US_PAR);
/* byte size */
switch (termios->c_cflag & CSIZE) {
case CS5:
mode |= AT91_US_CHRL_5;
break;
case CS6:
mode |= AT91_US_CHRL_6;
break;
case CS7:
mode |= AT91_US_CHRL_7;
break;
default:
mode |= AT91_US_CHRL_8;
break;
}
/* stop bits */
if (termios->c_cflag & CSTOPB)
mode |= AT91_US_NBSTOP_2;
/* parity */
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */
if (termios->c_cflag & PARODD)
mode |= AT91_US_PAR_MARK;
else
mode |= AT91_US_PAR_SPACE;
}
else if (termios->c_cflag & PARODD)
mode |= AT91_US_PAR_ODD;
else
mode |= AT91_US_PAR_EVEN;
}
else
mode |= AT91_US_PAR_NONE;
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask |= AT91_US_OVRE;
if (termios->c_iflag & INPCK)
port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= AT91_US_RXBRK;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= (AT91_US_FRAME | AT91_US_PARE);
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= AT91_US_RXBRK;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= AT91_US_OVRE;
}
// TODO: Ignore all characters if CREAD is set.
/* update the per-port timeout */
uart_update_timeout(port, termios->c_cflag, baud);
/* disable interrupts and drain transmitter */
imr = UART_GET_IMR(port); /* get interrupt mask */
UART_PUT_IDR(port, -1); /* disable all interrupts */
while (!(UART_GET_CSR(port) & AT91_US_TXEMPTY)) { barrier(); }
/* disable receiver and transmitter */
UART_PUT_CR(port, AT91_US_TXDIS | AT91_US_RXDIS);
/* set the parity, stop bits and data size */
UART_PUT_MR(port, mode);
/* set the baud rate */
UART_PUT_BRGR(port, quot);
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
/* restore interrupts */
UART_PUT_IER(port, imr);
/* CTS flow-control and modem-status interrupts */
if (UART_ENABLE_MS(port, termios->c_cflag))
port->ops->enable_ms(port);
spin_unlock_irqrestore(&port->lock, flags);
}
/*
* Return string describing the specified port
*/
static const char *at91_type(struct uart_port *port)
{
return (port->type == PORT_AT91RM9200) ? "AT91_SERIAL" : NULL;
}
/*
* Release the memory region(s) being used by 'port'.
*/
static void at91_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase,
(port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K);
}
/*
* Request the memory region(s) being used by 'port'.
*/
static int at91_request_port(struct uart_port *port)
{
return request_mem_region(port->mapbase,
(port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K,
"at91_serial") != NULL ? 0 : -EBUSY;
}
/*
* Configure/autoconfigure the port.
*/
static void at91_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE) {
port->type = PORT_AT91RM9200;
at91_request_port(port);
}
}
/*
* Verify the new serial_struct (for TIOCSSERIAL).
*/
static int at91_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91RM9200)
ret = -EINVAL;
if (port->irq != ser->irq)
ret = -EINVAL;
if (ser->io_type != SERIAL_IO_MEM)
ret = -EINVAL;
if (port->uartclk / 16 != ser->baud_base)
ret = -EINVAL;
if ((void *)port->mapbase != ser->iomem_base)
ret = -EINVAL;
if (port->iobase != ser->port)
ret = -EINVAL;
if (ser->hub6 != 0)
ret = -EINVAL;
return ret;
}
static struct uart_ops at91_pops = {
.tx_empty = at91_tx_empty,
.set_mctrl = at91_set_mctrl,
.get_mctrl = at91_get_mctrl,
.stop_tx = at91_stop_tx,
.start_tx = at91_start_tx,
.stop_rx = at91_stop_rx,
.enable_ms = at91_enable_ms,
.break_ctl = at91_break_ctl,
.startup = at91_startup,
.shutdown = at91_shutdown,
.set_termios = at91_set_termios,
.type = at91_type,
.release_port = at91_release_port,
.request_port = at91_request_port,
.config_port = at91_config_port,
.verify_port = at91_verify_port,
.pm = at91_serial_pm,
};
static struct uart_port at91_ports[AT91_NR_UART];
void __init at91_init_ports(void)
{
static int first = 1;
int i;
if (!first)
return;
first = 0;
for (i = 0; i < AT91_NR_UART; i++) {
at91_ports[i].iotype = UPIO_MEM;
at91_ports[i].flags = UPF_BOOT_AUTOCONF;
at91_ports[i].uartclk = at91_master_clock;
at91_ports[i].ops = &at91_pops;
at91_ports[i].fifosize = 1;
at91_ports[i].line = i;
}
}
void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns)
{
if (fns->enable_ms)
at91_pops.enable_ms = fns->enable_ms;
if (fns->get_mctrl)
at91_pops.get_mctrl = fns->get_mctrl;
if (fns->set_mctrl)
at91_pops.set_mctrl = fns->set_mctrl;
at91_open = fns->open;
at91_close = fns->close;
at91_pops.pm = fns->pm;
at91_pops.set_wake = fns->set_wake;
}
/*
* Setup ports.
*/
void __init at91_register_uart(int idx, int port)
{
if ((idx < 0) || (idx >= AT91_NR_UART)) {
printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx);
return;
}
switch (port) {
case 0:
at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US0;
at91_ports[idx].mapbase = AT91_VA_BASE_US0;
at91_ports[idx].irq = AT91_ID_US0;
AT91_CfgPIO_USART0();
break;
case 1:
at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US1;
at91_ports[idx].mapbase = AT91_VA_BASE_US1;
at91_ports[idx].irq = AT91_ID_US1;
AT91_CfgPIO_USART1();
break;
case 2:
at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US2;
at91_ports[idx].mapbase = AT91_VA_BASE_US2;
at91_ports[idx].irq = AT91_ID_US2;
AT91_CfgPIO_USART2();
break;
case 3:
at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US3;
at91_ports[idx].mapbase = AT91_VA_BASE_US3;
at91_ports[idx].irq = AT91_ID_US3;
AT91_CfgPIO_USART3();
break;
case 4:
at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_DBGU;
at91_ports[idx].mapbase = AT91_VA_BASE_DBGU;
at91_ports[idx].irq = AT91_ID_SYS;
AT91_CfgPIO_DBGU();
break;
default:
printk(KERN_ERR "%s : bad port number %d\n", __FUNCTION__, port);
}
}
#ifdef CONFIG_SERIAL_AT91_CONSOLE
/*
* Interrupts are disabled on entering
*/
static void at91_console_write(struct console *co, const char *s, u_int count)
{
struct uart_port *port = at91_ports + co->index;
unsigned int status, i, imr;
/*
* First, save IMR and then disable interrupts
*/
imr = UART_GET_IMR(port); /* get interrupt mask */
UART_PUT_IDR(port, AT91_US_RXRDY | AT91_US_TXRDY);
/*
* Now, do each character
*/
for (i = 0; i < count; i++) {
do {
status = UART_GET_CSR(port);
} while (!(status & AT91_US_TXRDY));
UART_PUT_CHAR(port, s[i]);
if (s[i] == '\n') {
do {
status = UART_GET_CSR(port);
} while (!(status & AT91_US_TXRDY));
UART_PUT_CHAR(port, '\r');
}
}
/*
* Finally, wait for transmitter to become empty
* and restore IMR
*/
do {
status = UART_GET_CSR(port);
} while (!(status & AT91_US_TXRDY));
UART_PUT_IER(port, imr); /* set interrupts back the way they were */
}
/*
* If the port was already initialised (eg, by a boot loader), try to determine
* the current setup.
*/
static void __init at91_console_get_options(struct uart_port *port, int *baud, int *parity, int *bits)
{
unsigned int mr, quot;
// TODO: CR is a write-only register
// unsigned int cr;
//
// cr = UART_GET_CR(port) & (AT91_US_RXEN | AT91_US_TXEN);
// if (cr == (AT91_US_RXEN | AT91_US_TXEN)) {
// /* ok, the port was enabled */
// }
mr = UART_GET_MR(port) & AT91_US_CHRL;
if (mr == AT91_US_CHRL_8)
*bits = 8;
else
*bits = 7;
mr = UART_GET_MR(port) & AT91_US_PAR;
if (mr == AT91_US_PAR_EVEN)
*parity = 'e';
else if (mr == AT91_US_PAR_ODD)
*parity = 'o';
quot = UART_GET_BRGR(port);
*baud = port->uartclk / (16 * (quot));
}
static int __init at91_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 115200;
int bits = 8;
int parity = 'n';
int flow = 'n';
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
port = uart_get_console(at91_ports, AT91_NR_UART, co);
/*
* Enable the serial console, in-case bootloader did not do it.
*/
at91_sys_write(AT91_PMC_PCER, 1 << port->irq); /* enable clock */
UART_PUT_IDR(port, -1); /* disable interrupts */
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
at91_console_get_options(port, &baud, &parity, &bits);
return uart_set_options(port, co, baud, parity, bits, flow);
}
static struct uart_driver at91_uart;
static struct console at91_console = {
.name = AT91_DEVICENAME,
.write = at91_console_write,
.device = uart_console_device,
.setup = at91_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &at91_uart,
};
#define AT91_CONSOLE_DEVICE &at91_console
static int __init at91_console_init(void)
{
at91_init_ports();
at91_console.index = at91_console_port;
register_console(&at91_console);
return 0;
}
console_initcall(at91_console_init);
#else
#define AT91_CONSOLE_DEVICE NULL
#endif
static struct uart_driver at91_uart = {
.owner = THIS_MODULE,
.driver_name = AT91_DEVICENAME,
.dev_name = AT91_DEVICENAME,
.devfs_name = AT91_DEVICENAME,
.major = SERIAL_AT91_MAJOR,
.minor = MINOR_START,
.nr = AT91_NR_UART,
.cons = AT91_CONSOLE_DEVICE,
};
static int __init at91_serial_init(void)
{
int ret, i;
at91_init_ports();
ret = uart_register_driver(&at91_uart);
if (ret)
return ret;
for (i = 0; i < AT91_NR_UART; i++) {
if (at91_serial_map[i] >= 0)
uart_add_one_port(&at91_uart, &at91_ports[i]);
}
return 0;
}
static void __exit at91_serial_exit(void)
{
int i;
for (i = 0; i < AT91_NR_UART; i++) {
if (at91_serial_map[i] >= 0)
uart_remove_one_port(&at91_uart, &at91_ports[i]);
}
uart_unregister_driver(&at91_uart);
}
module_init(at91_serial_init);
module_exit(at91_serial_exit);
MODULE_AUTHOR("Rick Bronson");
MODULE_DESCRIPTION("AT91 generic serial port driver");
MODULE_LICENSE("GPL");
