#ifndef NET2280_H
#define NET2280_H
/*
* NetChip 2280 high/full speed USB device controller.
* Unlike many such controllers, this one talks PCI.
*/
/*
* Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
* Copyright (C) 2003 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
/*-------------------------------------------------------------------------*/
/* NET2280 MEMORY MAPPED REGISTERS
*
* The register layout came from the chip documentation, and the bit
* number definitions were extracted from chip specification.
*
* Use the shift operator ('<<') to build bit masks, with readl/writel
* to access the registers through PCI.
*/
/* main registers, BAR0 + 0x0000 */
struct net2280_regs {
/* offset 0x0000 */
__le32 devinit;
#define LOCAL_CLOCK_FREQUENCY 8
#define FORCE_PCI_RESET 7
#define PCI_ID 6
#define PCI_ENABLE 5
#define FIFO_SOFT_RESET 4
#define CFG_SOFT_RESET 3
#define PCI_SOFT_RESET 2
#define USB_SOFT_RESET 1
#define M8051_RESET 0
__le32 eectl;
#define EEPROM_ADDRESS_WIDTH 23
#define EEPROM_CHIP_SELECT_ACTIVE 22
#define EEPROM_PRESENT 21
#define EEPROM_VALID 20
#define EEPROM_BUSY 19
#define EEPROM_CHIP_SELECT_ENABLE 18
#define EEPROM_BYTE_READ_START 17
#define EEPROM_BYTE_WRITE_START 16
#define EEPROM_READ_DATA 8
#define EEPROM_WRITE_DATA 0
__le32 eeclkfreq;
u32 _unused0;
/* offset 0x0010 */
__le32 pciirqenb0; /* interrupt PCI master ... */
#define SETUP_PACKET_INTERRUPT_ENABLE 7
#define ENDPOINT_F_INTERRUPT_ENABLE 6
#define ENDPOINT_E_INTERRUPT_ENABLE 5
#define ENDPOINT_D_INTERRUPT_ENABLE 4
#define ENDPOINT_C_INTERRUPT_ENABLE 3
#define ENDPOINT_B_INTERRUPT_ENABLE 2
#define ENDPOINT_A_INTERRUPT_ENABLE 1
#define ENDPOINT_0_INTERRUPT_ENABLE 0
__le32 pciirqenb1;
#define PCI_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
__le32 cpu_irqenb0; /* ... or onboard 8051 */
#define SETUP_PACKET_INTERRUPT_ENABLE 7
#define ENDPOINT_F_INTERRUPT_ENABLE 6
#define ENDPOINT_E_INTERRUPT_ENABLE 5
#define ENDPOINT_D_INTERRUPT_ENABLE 4
#define ENDPOINT_C_INTERRUPT_ENABLE 3
#define ENDPOINT_B_INTERRUPT_ENABLE 2
#define ENDPOINT_A_INTERRUPT_ENABLE 1
#define ENDPOINT_0_INTERRUPT_ENABLE 0
__le32 cpu_irqenb1;
#define CPU_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_INTA_INTERRUPT_ENABLE 24
#define PCI_PME_INTERRUPT_ENABLE 23
#define PCI_SERR_INTERRUPT_ENABLE 22
#define PCI_PERR_INTERRUPT_ENABLE 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
/* offset 0x0020 */
u32 _unused1;
__le32 usbirqenb1;
#define USB_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_INTA_INTERRUPT_ENABLE 24
#define PCI_PME_INTERRUPT_ENABLE 23
#define PCI_SERR_INTERRUPT_ENABLE 22
#define PCI_PERR_INTERRUPT_ENABLE 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
__le32 irqstat0;
#define INTA_ASSERTED 12
#define SETUP_PACKET_INTERRUPT 7
#define ENDPOINT_F_INTERRUPT 6
#define ENDPOINT_E_INTERRUPT 5
#define ENDPOINT_D_INTERRUPT 4
#define ENDPOINT_C_INTERRUPT 3
#define ENDPOINT_B_INTERRUPT 2
#define ENDPOINT_A_INTERRUPT 1
#define ENDPOINT_0_INTERRUPT 0
__le32 irqstat1;
#define POWER_STATE_CHANGE_INTERRUPT 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
#define PCI_PARITY_ERROR_INTERRUPT 25
#define PCI_INTA_INTERRUPT 24
#define PCI_PME_INTERRUPT 23
#define PCI_SERR_INTERRUPT 22
#define PCI_PERR_INTERRUPT 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
#define PCI_RETRY_ABORT_INTERRUPT 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
#define GPIO_INTERRUPT 13
#define DMA_D_INTERRUPT 12
#define DMA_C_INTERRUPT 11
#define DMA_B_INTERRUPT 10
#define DMA_A_INTERRUPT 9
#define EEPROM_DONE_INTERRUPT 8
#define VBUS_INTERRUPT 7
#define CONTROL_STATUS_INTERRUPT 6
#define ROOT_PORT_RESET_INTERRUPT 4
#define SUSPEND_REQUEST_INTERRUPT 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
#define RESUME_INTERRUPT 1
#define SOF_INTERRUPT 0
/* offset 0x0030 */
__le32 idxaddr;
__le32 idxdata;
__le32 fifoctl;
#define PCI_BASE2_RANGE 16
#define IGNORE_FIFO_AVAILABILITY 3
#define PCI_BASE2_SELECT 2
#define FIFO_CONFIGURATION_SELECT 0
u32 _unused2;
/* offset 0x0040 */
__le32 memaddr;
#define START 28
#define DIRECTION 27
#define FIFO_DIAGNOSTIC_SELECT 24
#define MEMORY_ADDRESS 0
__le32 memdata0;
__le32 memdata1;
u32 _unused3;
/* offset 0x0050 */
__le32 gpioctl;
#define GPIO3_LED_SELECT 12
#define GPIO3_INTERRUPT_ENABLE 11
#define GPIO2_INTERRUPT_ENABLE 10
#define GPIO1_INTERRUPT_ENABLE 9
#define GPIO0_INTERRUPT_ENABLE 8
#define GPIO3_OUTPUT_ENABLE 7
#define GPIO2_OUTPUT_ENABLE 6
#define GPIO1_OUTPUT_ENABLE 5
#define GPIO0_OUTPUT_ENABLE 4
#define GPIO3_DATA 3
#define GPIO2_DATA 2
#define GPIO1_DATA 1
#define GPIO0_DATA 0
__le32 gpiostat;
#define GPIO3_INTERRUPT 3
#define GPIO2_INTERRUPT 2
#define GPIO1_INTERRUPT 1
#define GPIO0_INTERRUPT 0
} __attribute__ ((packed));
/* usb control, BAR0 + 0x0080 */
struct net2280_usb_regs {
/* offset 0x0080 */
__le32 stdrsp;
#define STALL_UNSUPPORTED_REQUESTS 31
#define SET_TEST_MODE 16
#define GET_OTHER_SPEED_CONFIGURATION 15
#define GET_DEVICE_QUALIFIER 14
#define SET_ADDRESS 13
#define ENDPOINT_SET_CLEAR_HALT 12
#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
#define GET_STRING_DESCRIPTOR_2 10
#define GET_STRING_DESCRIPTOR_1 9
#define GET_STRING_DESCRIPTOR_0 8
#define GET_SET_INTERFACE 6
#define GET_SET_CONFIGURATION 5
#define GET_CONFIGURATION_DESCRIPTOR 4
#define GET_DEVICE_DESCRIPTOR 3
#define GET_ENDPOINT_STATUS 2
#define GET_INTERFACE_STATUS 1
#define GET_DEVICE_STATUS 0
__le32 prodvendid;
#define PRODUCT_ID 16
#define VENDOR_ID 0
__le32 relnum;
__le32 usbctl;
#define SERIAL_NUMBER_INDEX 16
#define PRODUCT_ID_STRING_ENABLE 13
#define VENDOR_ID_STRING_ENABLE 12
#define USB_ROOT_PORT_WAKEUP_ENABLE 11
#define VBUS_PIN 10
#define TIMED_DISCONNECT 9
#define SUSPEND_IMMEDIATELY 7
#define SELF_POWERED_USB_DEVICE 6
#define REMOTE_WAKEUP_SUPPORT 5
#define PME_POLARITY 4
#define USB_DETECT_ENABLE 3
#define PME_WAKEUP_ENABLE 2
#define DEVICE_REMOTE_WAKEUP_ENABLE 1
#define SELF_POWERED_STATUS 0
/* offset 0x0090 */
__le32 usbstat;
#define HIGH_SPEED 7
#define FULL_SPEED 6
#define GENERATE_RESUME 5
#define GENERATE_DEVICE_REMOTE_WAKEUP 4
__le32 xcvrdiag;
#define FORCE_HIGH_SPEED_MODE 31
#define FORCE_FULL_SPEED_MODE 30
#define USB_TEST_MODE 24
#define LINE_STATE 16
#define TRANSCEIVER_OPERATION_MODE 2
#define TRANSCEIVER_SELECT 1
#define TERMINATION_SELECT 0
__le32 setup0123;
__le32 setup4567;
/* offset 0x0090 */
u32 _unused0;
__le32 ouraddr;
#define FORCE_IMMEDIATE 7
#define OUR_USB_ADDRESS 0
__le32 ourconfig;
} __attribute__ ((packed));
/* pci control, BAR0 + 0x0100 */
struct net2280_pci_regs {
/* offset 0x0100 */
__le32 pcimstctl;
#define PCI_ARBITER_PARK_SELECT 13
#define PCI_MULTI LEVEL_ARBITER 12
#define PCI_RETRY_ABORT_ENABLE 11
#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
#define DMA_READ_MULTIPLE_ENABLE 9
#define DMA_READ_LINE_ENABLE 8
#define PCI_MASTER_COMMAND_SELECT 6
#define MEM_READ_OR_WRITE 0
#define IO_READ_OR_WRITE 1
#define CFG_READ_OR_WRITE 2
#define PCI_MASTER_START 5
#define PCI_MASTER_READ_WRITE 4
#define PCI_MASTER_WRITE 0
#define PCI_MASTER_READ 1
#define PCI_MASTER_BYTE_WRITE_ENABLES 0
__le32 pcimstaddr;
__le32 pcimstdata;
__le32 pcimststat;
#define PCI_ARBITER_CLEAR 2
#define PCI_EXTERNAL_ARBITER 1
#define PCI_HOST_MODE 0
} __attribute__ ((packed));
/* dma control, BAR0 + 0x0180 ... array of four structs like this,
* for channels 0..3. see also struct net2280_dma: descriptor
* that can be loaded into some of these registers.
*/
struct net2280_dma_regs { /* [11.7] */
/* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */
__le32 dmactl;
#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
#define DMA_CLEAR_COUNT_ENABLE 21
#define DESCRIPTOR_POLLING_RATE 19
#define POLL_CONTINUOUS 0
#define POLL_1_USEC 1
#define POLL_100_USEC 2
#define POLL_1_MSEC 3
#define DMA_VALID_BIT_POLLING_ENABLE 18
#define DMA_VALID_BIT_ENABLE 17
#define DMA_SCATTER_GATHER_ENABLE 16
#define DMA_OUT_AUTO_START_ENABLE 4
#define DMA_PREEMPT_ENABLE 3
#define DMA_FIFO_VALIDATE 2
#define DMA_ENABLE 1
#define DMA_ADDRESS_HOLD 0
__le32 dmastat;
#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
#define DMA_TRANSACTION_DONE_INTERRUPT 24
#define DMA_ABORT 1
#define DMA_START 0
u32 _unused0[2];
/* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */
__le32 dmacount;
#define VALID_BIT 31
#define DMA_DIRECTION 30
#define DMA_DONE_INTERRUPT_ENABLE 29
#define END_OF_CHAIN 28
#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
#define DMA_BYTE_COUNT 0
__le32 dmaaddr;
__le32 dmadesc;
u32 _unused1;
} __attribute__ ((packed));
/* dedicated endpoint registers, BAR0 + 0x0200 */
struct net2280_dep_regs { /* [11.8] */
/* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */
__le32 dep_cfg;
/* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */
__le32 dep_rsp;
u32 _unused[2];
} __attribute__ ((packed));
/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
* like this, for ep0 then the configurable endpoints A..F
* ep0 reserved for control; E and F have only 64 bytes of fifo
*/
struct net2280_ep_regs { /* [11.9] */
/* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */
__le32 ep_cfg;
#define ENDPOINT_BYTE_COUNT 16
#define ENDPOINT_ENABLE 10
#define ENDPOINT_TYPE 8
#define ENDPOINT_DIRECTION 7
#define ENDPOINT_NUMBER 0
__le32 ep_rsp;
#define SET_NAK_OUT_PACKETS 15
#define SET_EP_HIDE_STATUS_PHASE 14
#define SET_EP_FORCE_CRC_ERROR 13
#define SET_INTERRUPT_MODE 12
#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
#define SET_NAK_OUT_PACKETS_MODE 10
#define SET_ENDPOINT_TOGGLE 9
#define SET_ENDPOINT_HALT 8
#define CLEAR_NAK_OUT_PACKETS 7
#define CLEAR_EP_HIDE_STATUS_PHASE 6
#define CLEAR_EP_FORCE_CRC_ERROR 5
#define CLEAR_INTERRUPT_MODE 4
#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
#define CLEAR_NAK_OUT_PACKETS_MODE 2
#define CLEAR_ENDPOINT_TOGGLE 1
#define CLEAR_ENDPOINT_HALT 0
__le32 ep_irqenb;
#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
__le32 ep_stat;
#define FIFO_VALID_COUNT 24
#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
#define TIMEOUT 21
#define USB_STALL_SENT 20
#define USB_IN_NAK_SENT 19
#define USB_IN_ACK_RCVD 18
#define USB_OUT_PING_NAK_SENT 17
#define USB_OUT_ACK_SENT 16
#define FIFO_OVERFLOW 13
#define FIFO_UNDERFLOW 12
#define FIFO_FULL 11
#define FIFO_EMPTY 10
#define FIFO_FLUSH 9
#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
#define NAK_OUT_PACKETS 4
#define DATA_PACKET_RECEIVED_INTERRUPT 3
#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
#define DATA_OUT_PING_TOKEN_INTERRUPT 1
#define DATA_IN_TOKEN_INTERRUPT 0
/* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */
__le32 ep_avail;
__le32 ep_data;
u32 _unused0[2];
} __attribute__ ((packed));
struct net2280_reg_write {
__le16 port;
__le32 addr;
__le32 val;
} __attribute__ ((packed));
struct net2280_reg_read {
__le16 port;
__le32 addr;
} __attribute__ ((packed));
#endif /* NET2280_H */
