/******************************************************************************
*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2008 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
* USA
*
* The full GNU General Public License is included in this distribution
* in the file called LICENSE.GPL.
*
* Contact Information:
* Tomas Winkler <tomas.winkler@intel.com>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
* BSD LICENSE
*
* Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*****************************************************************************/
#ifndef __iwl_eeprom_h__
#define __iwl_eeprom_h__
struct iwl4965_priv;
/*
* EEPROM access time values:
*
* Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
* then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
* CSR_EEPROM_REG_BIT_CMD (0x2).
* Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
* When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
* Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
*/
#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
#define IWL_EEPROM_SEM_TIMEOUT 10 /* milliseconds */
#define IWL_EEPROM_SEM_RETRY_LIMIT 1000 /* number of attempts (not time) */
/*
* Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
*
* IBSS and/or AP operation is allowed *only* on those channels with
* (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
* RADAR detection is not supported by the 4965 driver, but is a
* requirement for establishing a new network for legal operation on channels
* requiring RADAR detection or restricting ACTIVE scanning.
*
* NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
* It only indicates that 20 MHz channel use is supported; FAT channel
* usage is indicated by a separate set of regulatory flags for each
* FAT channel pair.
*
* NOTE: Using a channel inappropriately will result in a uCode error!
*/
#define IWL_NUM_TX_CALIB_GROUPS 5
enum {
EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
/* Bit 2 Reserved */
EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
};
/* SKU Capabilities */
#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
/* *regulatory* channel data format in eeprom, one for each channel.
* There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
struct iwl4965_eeprom_channel {
u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));
/* 4965 has two radio transmitters (and 3 radio receivers) */
#define EEPROM_TX_POWER_TX_CHAINS (2)
/* 4965 has room for up to 8 sets of txpower calibration data */
#define EEPROM_TX_POWER_BANDS (8)
/* 4965 factory calibration measures txpower gain settings for
* each of 3 target output levels */
#define EEPROM_TX_POWER_MEASUREMENTS (3)
#define EEPROM_4965_TX_POWER_VERSION (2)
/* 4965 driver does not work with txpower calibration version < 5.
* Look for this in calib_version member of struct iwl4965_eeprom. */
#define EEPROM_TX_POWER_VERSION_NEW (5)
/*
* 4965 factory calibration data for one txpower level, on one channel,
* measured on one of the 2 tx chains (radio transmitter and associated
* antenna). EEPROM contains:
*
* 1) Temperature (degrees Celsius) of device when measurement was made.
*
* 2) Gain table index used to achieve the target measurement power.
* This refers to the "well-known" gain tables (see iwl-4965-hw.h).
*
* 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
*
* 4) RF power amplifier detector level measurement (not used).
*/
struct iwl4965_eeprom_calib_measure {
u8 temperature; /* Device temperature (Celsius) */
u8 gain_idx; /* Index into gain table */
u8 actual_pow; /* Measured RF output power, half-dBm */
s8 pa_det; /* Power amp detector level (not used) */
} __attribute__ ((packed));
/*
* 4965 measurement set for one channel. EEPROM contains:
*
* 1) Channel number measured
*
* 2) Measurements for each of 3 power levels for each of 2 radio transmitters
* (a.k.a. "tx chains") (6 measurements altogether)
*/
struct iwl4965_eeprom_calib_ch_info {
u8 ch_num;
struct iwl4965_eeprom_calib_measure
measurements[EEPROM_TX_POWER_TX_CHAINS]
[EEPROM_TX_POWER_MEASUREMENTS];
} __attribute__ ((packed));
/*
* 4965 txpower subband info.
*
* For each frequency subband, EEPROM contains the following:
*
* 1) First and last channels within range of the subband. "0" values
* indicate that this sample set is not being used.
*
* 2) Sample measurement sets for 2 channels close to the range endpoints.
*/
struct iwl4965_eeprom_calib_subband_info {
u8 ch_from; /* channel number of lowest channel in subband */
u8 ch_to; /* channel number of highest channel in subband */
struct iwl4965_eeprom_calib_ch_info ch1;
struct iwl4965_eeprom_calib_ch_info ch2;
} __attribute__ ((packed));
/*
* 4965 txpower calibration info. EEPROM contains:
*
* 1) Factory-measured saturation power levels (maximum levels at which
* tx power amplifier can output a signal without too much distortion).
* There is one level for 2.4 GHz band and one for 5 GHz band. These
* values apply to all channels within each of the bands.
*
* 2) Factory-measured power supply voltage level. This is assumed to be
* constant (i.e. same value applies to all channels/bands) while the
* factory measurements are being made.
*
* 3) Up to 8 sets of factory-measured txpower calibration values.
* These are for different frequency ranges, since txpower gain
* characteristics of the analog radio circuitry vary with frequency.
*
* Not all sets need to be filled with data;
* struct iwl4965_eeprom_calib_subband_info contains range of channels
* (0 if unused) for each set of data.
*/
struct iwl4965_eeprom_calib_info {
u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
u8 saturation_power52; /* half-dBm */
s16 voltage; /* signed */
struct iwl4965_eeprom_calib_subband_info
band_info[EEPROM_TX_POWER_BANDS];
} __attribute__ ((packed));
/*
* 4965 EEPROM map
*/
struct iwl4965_eeprom {
u8 reserved0[16];
#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
u16 device_id; /* abs.ofs: 16 */
u8 reserved1[2];
#define EEPROM_PMC (2*0x0A) /* 2 bytes */
u16 pmc; /* abs.ofs: 20 */
u8 reserved2[20];
#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
u8 mac_address[6]; /* abs.ofs: 42 */
u8 reserved3[58];
#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
u16 board_revision; /* abs.ofs: 106 */
u8 reserved4[11];
#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
u8 board_pba_number[9]; /* abs.ofs: 119 */
u8 reserved5[8];
#define EEPROM_VERSION (2*0x44) /* 2 bytes */
u16 version; /* abs.ofs: 136 */
#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
u8 sku_cap; /* abs.ofs: 138 */
#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
u8 leds_mode; /* abs.ofs: 139 */
#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
u16 oem_mode;
#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
u16 wowlan_mode; /* abs.ofs: 142 */
#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
u16 leds_time_interval; /* abs.ofs: 144 */
#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
u8 leds_off_time; /* abs.ofs: 146 */
#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
u8 leds_on_time; /* abs.ofs: 147 */
#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
u8 almgor_m_version; /* abs.ofs: 148 */
#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
u8 antenna_switch_type; /* abs.ofs: 149 */
u8 reserved6[8];
#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
u16 board_revision_4965; /* abs.ofs: 158 */
u8 reserved7[13];
#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
u8 reserved8[10];
#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
u8 sku_id[4]; /* abs.ofs: 192 */
/*
* Per-channel regulatory data.
*
* Each channel that *might* be supported by 3945 or 4965 has a fixed location
* in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
* txpower (MSB).
*
* Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
* channels (only for 4965, not supported by 3945) appear later in the EEPROM.
*
* 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
*/
#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
u16 band_1_count; /* abs.ofs: 196 */
#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
/*
* 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
* 5.0 GHz channels 7, 8, 11, 12, 16
* (4915-5080MHz) (none of these is ever supported)
*/
#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
u16 band_2_count; /* abs.ofs: 226 */
#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
/*
* 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
* (5170-5320MHz)
*/
#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
u16 band_3_count; /* abs.ofs: 254 */
#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
/*
* 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
* (5500-5700MHz)
*/
#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
u16 band_4_count; /* abs.ofs: 280 */
#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
/*
* 5.7 GHz channels 145, 149, 153, 157, 161, 165
* (5725-5825MHz)
*/
#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
u16 band_5_count; /* abs.ofs: 304 */
#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
u8 reserved10[2];
/*
* 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
*
* The channel listed is the center of the lower 20 MHz half of the channel.
* The overall center frequency is actually 2 channels (10 MHz) above that,
* and the upper half of each FAT channel is centered 4 channels (20 MHz) away
* from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
* and the overall FAT channel width centers on channel 3.
*
* NOTE: The RXON command uses 20 MHz channel numbers to specify the
* control channel to which to tune. RXON also specifies whether the
* control channel is the upper or lower half of a FAT channel.
*
* NOTE: 4965 does not support FAT channels on 2.4 GHz.
*/
#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
u8 reserved11[2];
/*
* 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
* 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
*/
#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
u8 reserved12[6];
/*
* 4965 driver requires txpower calibration format version 5 or greater.
* Driver does not work with txpower calibration version < 5.
* This value is simply a 16-bit number, no major/minor versions here.
*/
#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
u16 calib_version; /* abs.ofs: 364 */
u8 reserved13[2];
u8 reserved14[96]; /* abs.ofs: 368 */
/*
* 4965 Txpower calibration data.
*/
#define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */
struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */
u8 reserved16[140]; /* fill out to full 1024 byte block */
} __attribute__ ((packed));
#define IWL_EEPROM_IMAGE_SIZE 1024
/* End of EEPROM */
struct iwl_eeprom_ops {
int (*verify_signature) (struct iwl4965_priv *priv);
int (*acquire_semaphore) (struct iwl4965_priv *priv);
void (*release_semaphore) (struct iwl4965_priv *priv);
};
void iwl_eeprom_get_mac(const struct iwl4965_priv *priv, u8 *mac);
int iwl_eeprom_init(struct iwl4965_priv *priv);
int iwlcore_eeprom_verify_signature(struct iwl4965_priv *priv);
int iwlcore_eeprom_acquire_semaphore(struct iwl4965_priv *priv);
void iwlcore_eeprom_release_semaphore(struct iwl4965_priv *priv);
#endif /* __iwl_eeprom_h__ */
