/******************************************************************************
*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
* USA
*
* The full GNU General Public License is included in this distribution
* in the file called LICENSE.GPL.
*
* Contact Information:
* James P. Ketrenos <ipw2100-admin@linux.intel.com>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
* BSD LICENSE
*
* Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
/*
* Please use this file (iwl-3945-commands.h) only for uCode API definitions.
* Please use iwl-3945-hw.h for hardware-related definitions.
* Please use iwl-3945.h for driver implementation definitions.
*/
#ifndef __iwl_3945_commands_h__
#define __iwl_3945_commands_h__
/* uCode version contains 4 values: Major/Minor/API/Serial */
#define IWL_UCODE_MAJOR(ver) (((ver) & 0xFF000000) >> 24)
#define IWL_UCODE_MINOR(ver) (((ver) & 0x00FF0000) >> 16)
#define IWL_UCODE_API(ver) (((ver) & 0x0000FF00) >> 8)
#define IWL_UCODE_SERIAL(ver) ((ver) & 0x000000FF)
enum {
REPLY_ALIVE = 0x1,
REPLY_ERROR = 0x2,
/* RXON and QOS commands */
REPLY_RXON = 0x10,
REPLY_RXON_ASSOC = 0x11,
REPLY_QOS_PARAM = 0x13,
REPLY_RXON_TIMING = 0x14,
/* Multi-Station support */
REPLY_ADD_STA = 0x18,
REPLY_REMOVE_STA = 0x19, /* not used */
REPLY_REMOVE_ALL_STA = 0x1a, /* not used */
/* RX, TX, LEDs */
REPLY_3945_RX = 0x1b, /* 3945 only */
REPLY_TX = 0x1c,
REPLY_RATE_SCALE = 0x47, /* 3945 only */
REPLY_LEDS_CMD = 0x48,
REPLY_TX_LINK_QUALITY_CMD = 0x4e, /* 4965 only */
/* 802.11h related */
RADAR_NOTIFICATION = 0x70, /* not used */
REPLY_QUIET_CMD = 0x71, /* not used */
REPLY_CHANNEL_SWITCH = 0x72,
CHANNEL_SWITCH_NOTIFICATION = 0x73,
REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74,
SPECTRUM_MEASURE_NOTIFICATION = 0x75,
/* Power Management */
POWER_TABLE_CMD = 0x77,
PM_SLEEP_NOTIFICATION = 0x7A,
PM_DEBUG_STATISTIC_NOTIFIC = 0x7B,
/* Scan commands and notifications */
REPLY_SCAN_CMD = 0x80,
REPLY_SCAN_ABORT_CMD = 0x81,
SCAN_START_NOTIFICATION = 0x82,
SCAN_RESULTS_NOTIFICATION = 0x83,
SCAN_COMPLETE_NOTIFICATION = 0x84,
/* IBSS/AP commands */
BEACON_NOTIFICATION = 0x90,
REPLY_TX_BEACON = 0x91,
WHO_IS_AWAKE_NOTIFICATION = 0x94, /* not used */
/* Miscellaneous commands */
QUIET_NOTIFICATION = 0x96, /* not used */
REPLY_TX_PWR_TABLE_CMD = 0x97,
MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
/* Bluetooth device coexistence config command */
REPLY_BT_CONFIG = 0x9b,
/* Statistics */
REPLY_STATISTICS_CMD = 0x9c,
STATISTICS_NOTIFICATION = 0x9d,
/* RF-KILL commands and notifications */
REPLY_CARD_STATE_CMD = 0xa0,
CARD_STATE_NOTIFICATION = 0xa1,
/* Missed beacons notification */
MISSED_BEACONS_NOTIFICATION = 0xa2,
REPLY_MAX = 0xff
};
/******************************************************************************
* (0)
* Commonly used structures and definitions:
* Command header, txpower
*
*****************************************************************************/
/* iwl3945_cmd_header flags value */
#define IWL_CMD_FAILED_MSK 0x40
/**
* struct iwl3945_cmd_header
*
* This header format appears in the beginning of each command sent from the
* driver, and each response/notification received from uCode.
*/
struct iwl3945_cmd_header {
u8 cmd; /* Command ID: REPLY_RXON, etc. */
u8 flags; /* IWL_CMD_* */
/*
* The driver sets up the sequence number to values of its choosing.
* uCode does not use this value, but passes it back to the driver
* when sending the response to each driver-originated command, so
* the driver can match the response to the command. Since the values
* don't get used by uCode, the driver may set up an arbitrary format.
*
* There is one exception: uCode sets bit 15 when it originates
* the response/notification, i.e. when the response/notification
* is not a direct response to a command sent by the driver. For
* example, uCode issues REPLY_3945_RX when it sends a received frame
* to the driver; it is not a direct response to any driver command.
*
* The Linux driver uses the following format:
*
* 0:7 index/position within Tx queue
* 8:13 Tx queue selection
* 14:14 driver sets this to indicate command is in the 'huge'
* storage at the end of the command buffers, i.e. scan cmd
* 15:15 uCode sets this in uCode-originated response/notification
*/
__le16 sequence;
/* command or response/notification data follows immediately */
u8 data[0];
} __attribute__ ((packed));
/**
* struct iwl3945_tx_power
*
* Used in REPLY_TX_PWR_TABLE_CMD, REPLY_SCAN_CMD, REPLY_CHANNEL_SWITCH
*
* Each entry contains two values:
* 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
* linear value that multiplies the output of the digital signal processor,
* before being sent to the analog radio.
* 2) Radio gain. This sets the analog gain of the radio Tx path.
* It is a coarser setting, and behaves in a logarithmic (dB) fashion.
*
* Driver obtains values from struct iwl3945_tx_power power_gain_table[][].
*/
struct iwl3945_tx_power {
u8 tx_gain; /* gain for analog radio */
u8 dsp_atten; /* gain for DSP */
} __attribute__ ((packed));
/**
* struct iwl3945_power_per_rate
*
* Used in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
*/
struct iwl3945_power_per_rate {
u8 rate; /* plcp */
struct iwl3945_tx_power tpc;
u8 reserved;
} __attribute__ ((packed));
/******************************************************************************
* (0a)
* Alive and Error Commands & Responses:
*
*****************************************************************************/
#define UCODE_VALID_OK cpu_to_le32(0x1)
#define INITIALIZE_SUBTYPE (9)
/*
* ("Initialize") REPLY_ALIVE = 0x1 (response only, not a command)
*
* uCode issues this "initialize alive" notification once the initialization
* uCode image has completed its work, and is ready to load the runtime image.
* This is the *first* "alive" notification that the driver will receive after
* rebooting uCode; the "initialize" alive is indicated by subtype field == 9.
*
* See comments documenting "BSM" (bootstrap state machine).
*/
struct iwl3945_init_alive_resp {
u8 ucode_minor;
u8 ucode_major;
__le16 reserved1;
u8 sw_rev[8];
u8 ver_type;
u8 ver_subtype; /* "9" for initialize alive */
__le16 reserved2;
__le32 log_event_table_ptr;
__le32 error_event_table_ptr;
__le32 timestamp;
__le32 is_valid;
} __attribute__ ((packed));
/**
* REPLY_ALIVE = 0x1 (response only, not a command)
*
* uCode issues this "alive" notification once the runtime image is ready
* to receive commands from the driver. This is the *second* "alive"
* notification that the driver will receive after rebooting uCode;
* this "alive" is indicated by subtype field != 9.
*
* See comments documenting "BSM" (bootstrap state machine).
*
* This response includes two pointers to structures within the device's
* data SRAM (access via HBUS_TARG_MEM_* regs) that are useful for debugging:
*
* 1) log_event_table_ptr indicates base of the event log. This traces
* a 256-entry history of uCode execution within a circular buffer.
*
* 2) error_event_table_ptr indicates base of the error log. This contains
* information about any uCode error that occurs.
*
* The Linux driver can print both logs to the system log when a uCode error
* occurs.
*/
struct iwl3945_alive_resp {
u8 ucode_minor;
u8 ucode_major;
__le16 reserved1;
u8 sw_rev[8];
u8 ver_type;
u8 ver_subtype; /* not "9" for runtime alive */
__le16 reserved2;
__le32 log_event_table_ptr; /* SRAM address for event log */
__le32 error_event_table_ptr; /* SRAM address for error log */
__le32 timestamp;
__le32 is_valid;
} __attribute__ ((packed));
union tsf {
u8 byte[8];
__le16 word[4];
__le32 dw[2];
};
/*
* REPLY_ERROR = 0x2 (response only, not a command)
*/
struct iwl3945_error_resp {
__le32 error_type;
u8 cmd_id;
u8 reserved1;
__le16 bad_cmd_seq_num;
__le16 reserved2;
__le32 error_info;
union tsf timestamp;
} __attribute__ ((packed));
/******************************************************************************
* (1)
* RXON Commands & Responses:
*
*****************************************************************************/
/*
* Rx config defines & structure
*/
/* rx_config device types */
enum {
RXON_DEV_TYPE_AP = 1,
RXON_DEV_TYPE_ESS = 3,
RXON_DEV_TYPE_IBSS = 4,
RXON_DEV_TYPE_SNIFFER = 6,
};
/* rx_config flags */
/* band & modulation selection */
#define RXON_FLG_BAND_24G_MSK cpu_to_le32(1 << 0)
#define RXON_FLG_CCK_MSK cpu_to_le32(1 << 1)
/* auto detection enable */
#define RXON_FLG_AUTO_DETECT_MSK cpu_to_le32(1 << 2)
/* TGg protection when tx */
#define RXON_FLG_TGG_PROTECT_MSK cpu_to_le32(1 << 3)
/* cck short slot & preamble */
#define RXON_FLG_SHORT_SLOT_MSK cpu_to_le32(1 << 4)
#define RXON_FLG_SHORT_PREAMBLE_MSK cpu_to_le32(1 << 5)
/* antenna selection */
#define RXON_FLG_DIS_DIV_MSK cpu_to_le32(1 << 7)
#define RXON_FLG_ANT_SEL_MSK cpu_to_le32(0x0f00)
#define RXON_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
#define RXON_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
/* radar detection enable */
#define RXON_FLG_RADAR_DETECT_MSK cpu_to_le32(1 << 12)
#define RXON_FLG_TGJ_NARROW_BAND_MSK cpu_to_le32(1 << 13)
/* rx response to host with 8-byte TSF
* (according to ON_AIR deassertion) */
#define RXON_FLG_TSF2HOST_MSK cpu_to_le32(1 << 15)
/* rx_config filter flags */
/* accept all data frames */
#define RXON_FILTER_PROMISC_MSK cpu_to_le32(1 << 0)
/* pass control & management to host */
#define RXON_FILTER_CTL2HOST_MSK cpu_to_le32(1 << 1)
/* accept multi-cast */
#define RXON_FILTER_ACCEPT_GRP_MSK cpu_to_le32(1 << 2)
/* don't decrypt uni-cast frames */
#define RXON_FILTER_DIS_DECRYPT_MSK cpu_to_le32(1 << 3)
/* don't decrypt multi-cast frames */
#define RXON_FILTER_DIS_GRP_DECRYPT_MSK cpu_to_le32(1 << 4)
/* STA is associated */
#define RXON_FILTER_ASSOC_MSK cpu_to_le32(1 << 5)
/* transfer to host non bssid beacons in associated state */
#define RXON_FILTER_BCON_AWARE_MSK cpu_to_le32(1 << 6)
/**
* REPLY_RXON = 0x10 (command, has simple generic response)
*
* RXON tunes the radio tuner to a service channel, and sets up a number
* of parameters that are used primarily for Rx, but also for Tx operations.
*
* NOTE: When tuning to a new channel, driver must set the
* RXON_FILTER_ASSOC_MSK to 0. This will clear station-dependent
* info within the device, including the station tables, tx retry
* rate tables, and txpower tables. Driver must build a new station
* table and txpower table before transmitting anything on the RXON
* channel.
*
* NOTE: All RXONs wipe clean the internal txpower table. Driver must
* issue a new REPLY_TX_PWR_TABLE_CMD after each REPLY_RXON (0x10),
* regardless of whether RXON_FILTER_ASSOC_MSK is set.
*/
struct iwl3945_rxon_cmd {
u8 node_addr[6];
__le16 reserved1;
u8 bssid_addr[6];
__le16 reserved2;
u8 wlap_bssid_addr[6];
__le16 reserved3;
u8 dev_type;
u8 air_propagation;
__le16 reserved4;
u8 ofdm_basic_rates;
u8 cck_basic_rates;
__le16 assoc_id;
__le32 flags;
__le32 filter_flags;
__le16 channel;
__le16 reserved5;
} __attribute__ ((packed));
/*
* REPLY_RXON_ASSOC = 0x11 (command, has simple generic response)
*/
struct iwl3945_rxon_assoc_cmd {
__le32 flags;
__le32 filter_flags;
u8 ofdm_basic_rates;
u8 cck_basic_rates;
__le16 reserved;
} __attribute__ ((packed));
/*
* REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
*/
struct iwl3945_rxon_time_cmd {
union tsf timestamp;
__le16 beacon_interval;
__le16 atim_window;
__le32 beacon_init_val;
__le16 listen_interval;
__le16 reserved;
} __attribute__ ((packed));
/*
* REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
*/
struct iwl3945_channel_switch_cmd {
u8 band;
u8 expect_beacon;
__le16 channel;
__le32 rxon_flags;
__le32 rxon_filter_flags;
__le32 switch_time;
struct iwl3945_power_per_rate power[IWL_MAX_RATES];
} __attribute__ ((packed));
/*
* CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
*/
struct iwl3945_csa_notification {
__le16 band;
__le16 channel;
__le32 status; /* 0 - OK, 1 - fail */
} __attribute__ ((packed));
/******************************************************************************
* (2)
* Quality-of-Service (QOS) Commands & Responses:
*
*****************************************************************************/
/**
* struct iwl_ac_qos -- QOS timing params for REPLY_QOS_PARAM
* One for each of 4 EDCA access categories in struct iwl_qosparam_cmd
*
* @cw_min: Contention window, start value in numbers of slots.
* Should be a power-of-2, minus 1. Device's default is 0x0f.
* @cw_max: Contention window, max value in numbers of slots.
* Should be a power-of-2, minus 1. Device's default is 0x3f.
* @aifsn: Number of slots in Arbitration Interframe Space (before
* performing random backoff timing prior to Tx). Device default 1.
* @edca_txop: Length of Tx opportunity, in uSecs. Device default is 0.
*
* Device will automatically increase contention window by (2*CW) + 1 for each
* transmission retry. Device uses cw_max as a bit mask, ANDed with new CW
* value, to cap the CW value.
*/
struct iwl3945_ac_qos {
__le16 cw_min;
__le16 cw_max;
u8 aifsn;
u8 reserved1;
__le16 edca_txop;
} __attribute__ ((packed));
/* QoS flags defines */
#define QOS_PARAM_FLG_UPDATE_EDCA_MSK cpu_to_le32(0x01)
#define QOS_PARAM_FLG_TGN_MSK cpu_to_le32(0x02)
#define QOS_PARAM_FLG_TXOP_TYPE_MSK cpu_to_le32(0x10)
/* Number of Access Categories (AC) (EDCA), queues 0..3 */
#define AC_NUM 4
/*
* REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
*
* This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
* 0: Background, 1: Best Effort, 2: Video, 3: Voice.
*/
struct iwl3945_qosparam_cmd {
__le32 qos_flags;
struct iwl3945_ac_qos ac[AC_NUM];
} __attribute__ ((packed));
/******************************************************************************
* (3)
* Add/Modify Stations Commands & Responses:
*
*****************************************************************************/
/*
* Multi station support
*/
/* Special, dedicated locations within device's station table */
#define IWL_AP_ID 0
#define IWL_MULTICAST_ID 1
#define IWL_STA_ID 2
#define IWL3945_BROADCAST_ID 24
#define IWL3945_STATION_COUNT 25
#define IWL_STATION_COUNT 32 /* MAX(3945,4965)*/
#define IWL_INVALID_STATION 255
#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2);
#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8);
/* Use in mode field. 1: modify existing entry, 0: add new station entry */
#define STA_CONTROL_MODIFY_MSK 0x01
/* key flags __le16*/
#define STA_KEY_FLG_ENCRYPT_MSK cpu_to_le16(0x0007)
#define STA_KEY_FLG_NO_ENC cpu_to_le16(0x0000)
#define STA_KEY_FLG_WEP cpu_to_le16(0x0001)
#define STA_KEY_FLG_CCMP cpu_to_le16(0x0002)
#define STA_KEY_FLG_TKIP cpu_to_le16(0x0003)
#define STA_KEY_FLG_KEYID_POS 8
#define STA_KEY_FLG_INVALID cpu_to_le16(0x0800)
/* wep key is either from global key (0) or from station info array (1) */
#define STA_KEY_FLG_WEP_KEY_MAP_MSK cpu_to_le16(0x0008)
/* wep key in STA: 5-bytes (0) or 13-bytes (1) */
#define STA_KEY_FLG_KEY_SIZE_MSK cpu_to_le16(0x1000)
#define STA_KEY_MULTICAST_MSK cpu_to_le16(0x4000)
/* Flags indicate whether to modify vs. don't change various station params */
#define STA_MODIFY_KEY_MASK 0x01
#define STA_MODIFY_TID_DISABLE_TX 0x02
#define STA_MODIFY_TX_RATE_MSK 0x04
/*
* Antenna masks:
* bit14:15 01 B inactive, A active
* 10 B active, A inactive
* 11 Both active
*/
#define RATE_MCS_ANT_A_POS 14
#define RATE_MCS_ANT_B_POS 15
#define RATE_MCS_ANT_A_MSK 0x4000
#define RATE_MCS_ANT_B_MSK 0x8000
#define RATE_MCS_ANT_AB_MSK 0xc000
struct iwl3945_keyinfo {
__le16 key_flags;
u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
u8 reserved1;
__le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
u8 key_offset;
u8 reserved2;
u8 key[16]; /* 16-byte unicast decryption key */
} __attribute__ ((packed));
/**
* struct sta_id_modify
* @addr[ETH_ALEN]: station's MAC address
* @sta_id: index of station in uCode's station table
* @modify_mask: STA_MODIFY_*, 1: modify, 0: don't change
*
* Driver selects unused table index when adding new station,
* or the index to a pre-existing station entry when modifying that station.
* Some indexes have special purposes (IWL_AP_ID, index 0, is for AP).
*
* modify_mask flags select which parameters to modify vs. leave alone.
*/
struct sta_id_modify {
u8 addr[ETH_ALEN];
__le16 reserved1;
u8 sta_id;
u8 modify_mask;
__le16 reserved2;
} __attribute__ ((packed));
/*
* REPLY_ADD_STA = 0x18 (command)
*
* The device contains an internal table of per-station information,
* with info on security keys, aggregation parameters, and Tx rates for
* initial Tx attempt and any retries (4965 uses REPLY_TX_LINK_QUALITY_CMD,
* 3945 uses REPLY_RATE_SCALE to set up rate tables).
*
* REPLY_ADD_STA sets up the table entry for one station, either creating
* a new entry, or modifying a pre-existing one.
*
* NOTE: RXON command (without "associated" bit set) wipes the station table
* clean. Moving into RF_KILL state does this also. Driver must set up
* new station table before transmitting anything on the RXON channel
* (except active scans or active measurements; those commands carry
* their own txpower/rate setup data).
*
* When getting started on a new channel, driver must set up the
* IWL_BROADCAST_ID entry (last entry in the table). For a client
* station in a BSS, once an AP is selected, driver sets up the AP STA
* in the IWL_AP_ID entry (1st entry in the table). BROADCAST and AP
* are all that are needed for a BSS client station. If the device is
* used as AP, or in an IBSS network, driver must set up station table
* entries for all STAs in network, starting with index IWL_STA_ID.
*/
struct iwl3945_addsta_cmd {
u8 mode; /* 1: modify existing, 0: add new station */
u8 reserved[3];
struct sta_id_modify sta;
struct iwl3945_keyinfo key;
__le32 station_flags; /* STA_FLG_* */
__le32 station_flags_msk; /* STA_FLG_* */
/* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
* corresponding to bit (e.g. bit 5 controls TID 5).
* Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
__le16 tid_disable_tx;
__le16 rate_n_flags;
/* TID for which to add block-ack support.
* Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
u8 add_immediate_ba_tid;
/* TID for which to remove block-ack support.
* Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
u8 remove_immediate_ba_tid;
/* Starting Sequence Number for added block-ack support.
* Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
__le16 add_immediate_ba_ssn;
} __attribute__ ((packed));
#define ADD_STA_SUCCESS_MSK 0x1
#define ADD_STA_NO_ROOM_IN_TABLE 0x2
#define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
/*
* REPLY_ADD_STA = 0x18 (response)
*/
struct iwl3945_add_sta_resp {
u8 status; /* ADD_STA_* */
} __attribute__ ((packed));
/******************************************************************************
* (4)
* Rx Responses:
*
*****************************************************************************/
struct iwl3945_rx_frame_stats {
u8 phy_count;
u8 id;
u8 rssi;
u8 agc;
__le16 sig_avg;
__le16 noise_diff;
u8 payload[0];
} __attribute__ ((packed));
struct iwl3945_rx_frame_hdr {
__le16 channel;
__le16 phy_flags;
u8 reserved1;
u8 rate;
__le16 len;
u8 payload[0];
} __attribute__ ((packed));
#define RX_RES_STATUS_NO_CRC32_ERROR cpu_to_le32(1 << 0)
#define RX_RES_STATUS_NO_RXE_OVERFLOW cpu_to_le32(1 << 1)
#define RX_RES_PHY_FLAGS_BAND_24_MSK cpu_to_le16(1 << 0)
#define RX_RES_PHY_FLAGS_MOD_CCK_MSK cpu_to_le16(1 << 1)
#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK cpu_to_le16(1 << 2)
#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK cpu_to_le16(1 << 3)
#define RX_RES_PHY_FLAGS_ANTENNA_MSK cpu_to_le16(0xf0)
#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
#define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
#define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
#define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
#define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
#define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
#define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
#define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
#define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
struct iwl3945_rx_frame_end {
__le32 status;
__le64 timestamp;
__le32 beacon_timestamp;
} __attribute__ ((packed));
/*
* REPLY_3945_RX = 0x1b (response only, not a command)
*
* NOTE: DO NOT dereference from casts to this structure
* It is provided only for calculating minimum data set size.
* The actual offsets of the hdr and end are dynamic based on
* stats.phy_count
*/
struct iwl3945_rx_frame {
struct iwl3945_rx_frame_stats stats;
struct iwl3945_rx_frame_hdr hdr;
struct iwl3945_rx_frame_end end;
} __attribute__ ((packed));
/******************************************************************************
* (5)
* Tx Commands & Responses:
*
* Driver must place each REPLY_TX command into one of the prioritized Tx
* queues in host DRAM, shared between driver and device. When the device's
* Tx scheduler and uCode are preparing to transmit, the device pulls the
* Tx command over the PCI bus via one of the device's Tx DMA channels,
* to fill an internal FIFO from which data will be transmitted.
*
* uCode handles all timing and protocol related to control frames
* (RTS/CTS/ACK), based on flags in the Tx command.
*
* uCode handles retrying Tx when an ACK is expected but not received.
* This includes trying lower data rates than the one requested in the Tx
* command, as set up by the REPLY_RATE_SCALE (for 3945) or
* REPLY_TX_LINK_QUALITY_CMD (4965).
*
* Driver sets up transmit power for various rates via REPLY_TX_PWR_TABLE_CMD.
* This command must be executed after every RXON command, before Tx can occur.
*****************************************************************************/
/* REPLY_TX Tx flags field */
/* 1: Use Request-To-Send protocol before this frame.
* Mutually exclusive vs. TX_CMD_FLG_CTS_MSK. */
#define TX_CMD_FLG_RTS_MSK cpu_to_le32(1 << 1)
/* 1: Transmit Clear-To-Send to self before this frame.
* Driver should set this for AUTH/DEAUTH/ASSOC-REQ/REASSOC mgmnt frames.
* Mutually exclusive vs. TX_CMD_FLG_RTS_MSK. */
#define TX_CMD_FLG_CTS_MSK cpu_to_le32(1 << 2)
/* 1: Expect ACK from receiving station
* 0: Don't expect ACK (MAC header's duration field s/b 0)
* Set this for unicast frames, but not broadcast/multicast. */
#define TX_CMD_FLG_ACK_MSK cpu_to_le32(1 << 3)
/* 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
* Tx command's initial_rate_index indicates first rate to try;
* uCode walks through table for additional Tx attempts.
* 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
* This rate will be used for all Tx attempts; it will not be scaled. */
#define TX_CMD_FLG_STA_RATE_MSK cpu_to_le32(1 << 4)
/* 1: Expect immediate block-ack.
* Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
#define TX_CMD_FLG_IMM_BA_RSP_MASK cpu_to_le32(1 << 6)
/* 1: Frame requires full Tx-Op protection.
* Set this if either RTS or CTS Tx Flag gets set. */
#define TX_CMD_FLG_FULL_TXOP_PROT_MSK cpu_to_le32(1 << 7)
/* Tx antenna selection field; used only for 3945, reserved (0) for 4965.
* Set field to "0" to allow 3945 uCode to select antenna (normal usage). */
#define TX_CMD_FLG_ANT_SEL_MSK cpu_to_le32(0xf00)
#define TX_CMD_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
#define TX_CMD_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
/* 1: Ignore Bluetooth priority for this frame.
* 0: Delay Tx until Bluetooth device is done (normal usage). */
#define TX_CMD_FLG_BT_DIS_MSK cpu_to_le32(1 << 12)
/* 1: uCode overrides sequence control field in MAC header.
* 0: Driver provides sequence control field in MAC header.
* Set this for management frames, non-QOS data frames, non-unicast frames,
* and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
#define TX_CMD_FLG_SEQ_CTL_MSK cpu_to_le32(1 << 13)
/* 1: This frame is non-last MPDU; more fragments are coming.
* 0: Last fragment, or not using fragmentation. */
#define TX_CMD_FLG_MORE_FRAG_MSK cpu_to_le32(1 << 14)
/* 1: uCode calculates and inserts Timestamp Function (TSF) in outgoing frame.
* 0: No TSF required in outgoing frame.
* Set this for transmitting beacons and probe responses. */
#define TX_CMD_FLG_TSF_MSK cpu_to_le32(1 << 16)
/* 1: Driver inserted 2 bytes pad after the MAC header, for (required) dword
* alignment of frame's payload data field.
* 0: No pad
* Set this for MAC headers with 26 or 30 bytes, i.e. those with QOS or ADDR4
* field (but not both). Driver must align frame data (i.e. data following
* MAC header) to DWORD boundary. */
#define TX_CMD_FLG_MH_PAD_MSK cpu_to_le32(1 << 20)
/* HCCA-AP - disable duration overwriting. */
#define TX_CMD_FLG_DUR_MSK cpu_to_le32(1 << 25)
/*
* TX command security control
*/
#define TX_CMD_SEC_WEP 0x01
#define TX_CMD_SEC_CCM 0x02
#define TX_CMD_SEC_TKIP 0x03
#define TX_CMD_SEC_MSK 0x03
#define TX_CMD_SEC_SHIFT 6
#define TX_CMD_SEC_KEY128 0x08
/*
* REPLY_TX = 0x1c (command)
*/
struct iwl3945_tx_cmd {
/*
* MPDU byte count:
* MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
* + 8 byte IV for CCM or TKIP (not used for WEP)
* + Data payload
* + 8-byte MIC (not used for CCM/WEP)
* NOTE: Does not include Tx command bytes, post-MAC pad bytes,
* MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
* Range: 14-2342 bytes.
*/
__le16 len;
/*
* MPDU or MSDU byte count for next frame.
* Used for fragmentation and bursting, but not 11n aggregation.
* Same as "len", but for next frame. Set to 0 if not applicable.
*/
__le16 next_frame_len;
__le32 tx_flags; /* TX_CMD_FLG_* */
u8 rate;
/* Index of recipient station in uCode's station table */
u8 sta_id;
u8 tid_tspec;
u8 sec_ctl;
u8 key[16];
union {
u8 byte[8];
__le16 word[4];
__le32 dw[2];
} tkip_mic;
__le32 next_frame_info;
union {
__le32 life_time;
__le32 attempt;
} stop_time;
u8 supp_rates[2];
u8 rts_retry_limit; /*byte 50 */
u8 data_retry_limit; /*byte 51 */
union {
__le16 pm_frame_timeout;
__le16 attempt_duration;
} timeout;
/*
* Duration of EDCA burst Tx Opportunity, in 32-usec units.
* Set this if txop time is not specified by HCCA protocol (e.g. by AP).
*/
__le16 driver_txop;
/*
* MAC header goes here, followed by 2 bytes padding if MAC header
* length is 26 or 30 bytes, followed by payload data
*/
u8 payload[0];
struct ieee80211_hdr hdr[0];
} __attribute__ ((packed));
/* TX command response is sent after *all* transmission attempts.
*
* NOTES:
*
* TX_STATUS_FAIL_NEXT_FRAG
*
* If the fragment flag in the MAC header for the frame being transmitted
* is set and there is insufficient time to transmit the next frame, the
* TX status will be returned with 'TX_STATUS_FAIL_NEXT_FRAG'.
*
* TX_STATUS_FIFO_UNDERRUN
*
* Indicates the host did not provide bytes to the FIFO fast enough while
* a TX was in progress.
*
* TX_STATUS_FAIL_MGMNT_ABORT
*
* This status is only possible if the ABORT ON MGMT RX parameter was
* set to true with the TX command.
*
* If the MSB of the status parameter is set then an abort sequence is
* required. This sequence consists of the host activating the TX Abort
* control line, and then waiting for the TX Abort command response. This
* indicates that a the device is no longer in a transmit state, and that the
* command FIFO has been cleared. The host must then deactivate the TX Abort
* control line. Receiving is still allowed in this case.
*/
enum {
TX_STATUS_SUCCESS = 0x01,
TX_STATUS_DIRECT_DONE = 0x02,
TX_STATUS_FAIL_SHORT_LIMIT = 0x82,
TX_STATUS_FAIL_LONG_LIMIT = 0x83,
TX_STATUS_FAIL_FIFO_UNDERRUN = 0x84,
TX_STATUS_FAIL_MGMNT_ABORT = 0x85,
TX_STATUS_FAIL_NEXT_FRAG = 0x86,
TX_STATUS_FAIL_LIFE_EXPIRE = 0x87,
TX_STATUS_FAIL_DEST_PS = 0x88,
TX_STATUS_FAIL_ABORTED = 0x89,
TX_STATUS_FAIL_BT_RETRY = 0x8a,
TX_STATUS_FAIL_STA_INVALID = 0x8b,
TX_STATUS_FAIL_FRAG_DROPPED = 0x8c,
TX_STATUS_FAIL_TID_DISABLE = 0x8d,
TX_STATUS_FAIL_FRAME_FLUSHED = 0x8e,
TX_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
TX_STATUS_FAIL_TX_LOCKED = 0x90,
TX_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
};
#define TX_PACKET_MODE_REGULAR 0x0000
#define TX_PACKET_MODE_BURST_SEQ 0x0100
#define TX_PACKET_MODE_BURST_FIRST 0x0200
enum {
TX_POWER_PA_NOT_ACTIVE = 0x0,
};
enum {
TX_STATUS_MSK = 0x000000ff, /* bits 0:7 */
TX_STATUS_DELAY_MSK = 0x00000040,
TX_STATUS_ABORT_MSK = 0x00000080,
TX_PACKET_MODE_MSK = 0x0000ff00, /* bits 8:15 */
TX_FIFO_NUMBER_MSK = 0x00070000, /* bits 16:18 */
TX_RESERVED = 0x00780000, /* bits 19:22 */
TX_POWER_PA_DETECT_MSK = 0x7f800000, /* bits 23:30 */
TX_ABORT_REQUIRED_MSK = 0x80000000, /* bits 31:31 */
};
/*
* REPLY_TX = 0x1c (response)
*/
struct iwl3945_tx_resp {
u8 failure_rts;
u8 failure_frame;
u8 bt_kill_count;
u8 rate;
__le32 wireless_media_time;
__le32 status; /* TX status */
} __attribute__ ((packed));
/*
* REPLY_TX_PWR_TABLE_CMD = 0x97 (command, has simple generic response)
*/
struct iwl3945_txpowertable_cmd {
u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
u8 reserved;
__le16 channel;
struct iwl3945_power_per_rate power[IWL_MAX_RATES];
} __attribute__ ((packed));
struct iwl3945_rate_scaling_info {
__le16 rate_n_flags;
u8 try_cnt;
u8 next_rate_index;
} __attribute__ ((packed));
/**
* struct iwl3945_rate_scaling_cmd - Rate Scaling Command & Response
*
* REPLY_RATE_SCALE = 0x47 (command, has simple generic response)
*
* NOTE: The table of rates passed to the uCode via the
* RATE_SCALE command sets up the corresponding order of
* rates used for all related commands, including rate
* masks, etc.
*
* For example, if you set 9MB (PLCP 0x0f) as the first
* rate in the rate table, the bit mask for that rate
* when passed through ofdm_basic_rates on the REPLY_RXON
* command would be bit 0 (1 << 0)
*/
struct iwl3945_rate_scaling_cmd {
u8 table_id;
u8 reserved[3];
struct iwl3945_rate_scaling_info table[IWL_MAX_RATES];
} __attribute__ ((packed));
/*
* REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
*
* 3945 and 4965 support hardware handshake with Bluetooth device on
* same platform. Bluetooth device alerts wireless device when it will Tx;
* wireless device can delay or kill its own Tx to accommodate.
*/
struct iwl3945_bt_cmd {
u8 flags;
u8 lead_time;
u8 max_kill;
u8 reserved;
__le32 kill_ack_mask;
__le32 kill_cts_mask;
} __attribute__ ((packed));
/******************************************************************************
* (6)
* Spectrum Management (802.11h) Commands, Responses, Notifications:
*
*****************************************************************************/
/*
* Spectrum Management
*/
#define MEASUREMENT_FILTER_FLAG (RXON_FILTER_PROMISC_MSK | \
RXON_FILTER_CTL2HOST_MSK | \
RXON_FILTER_ACCEPT_GRP_MSK | \
RXON_FILTER_DIS_DECRYPT_MSK | \
RXON_FILTER_DIS_GRP_DECRYPT_MSK | \
RXON_FILTER_ASSOC_MSK | \
RXON_FILTER_BCON_AWARE_MSK)
struct iwl3945_measure_channel {
__le32 duration; /* measurement duration in extended beacon
* format */
u8 channel; /* channel to measure */
u8 type; /* see enum iwl3945_measure_type */
__le16 reserved;
} __attribute__ ((packed));
/*
* REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (command)
*/
struct iwl3945_spectrum_cmd {
__le16 len; /* number of bytes starting from token */
u8 token; /* token id */
u8 id; /* measurement id -- 0 or 1 */
u8 origin; /* 0 = TGh, 1 = other, 2 = TGk */
u8 periodic; /* 1 = periodic */
__le16 path_loss_timeout;
__le32 start_time; /* start time in extended beacon format */
__le32 reserved2;
__le32 flags; /* rxon flags */
__le32 filter_flags; /* rxon filter flags */
__le16 channel_count; /* minimum 1, maximum 10 */
__le16 reserved3;
struct iwl3945_measure_channel channels[10];
} __attribute__ ((packed));
/*
* REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (response)
*/
struct iwl3945_spectrum_resp {
u8 token;
u8 id; /* id of the prior command replaced, or 0xff */
__le16 status; /* 0 - command will be handled
* 1 - cannot handle (conflicts with another
* measurement) */
} __attribute__ ((packed));
enum iwl3945_measurement_state {
IWL_MEASUREMENT_START = 0,
IWL_MEASUREMENT_STOP = 1,
};
enum iwl3945_measurement_status {
IWL_MEASUREMENT_OK = 0,
IWL_MEASUREMENT_CONCURRENT = 1,
IWL_MEASUREMENT_CSA_CONFLICT = 2,
IWL_MEASUREMENT_TGH_CONFLICT = 3,
/* 4-5 reserved */
IWL_MEASUREMENT_STOPPED = 6,
IWL_MEASUREMENT_TIMEOUT = 7,
IWL_MEASUREMENT_PERIODIC_FAILED = 8,
};
#define NUM_ELEMENTS_IN_HISTOGRAM 8
struct iwl3945_measurement_histogram {
__le32 ofdm[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 0.8usec counts */
__le32 cck[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 1usec counts */
} __attribute__ ((packed));
/* clear channel availability counters */
struct iwl3945_measurement_cca_counters {
__le32 ofdm;
__le32 cck;
} __attribute__ ((packed));
enum iwl3945_measure_type {
IWL_MEASURE_BASIC = (1 << 0),
IWL_MEASURE_CHANNEL_LOAD = (1 << 1),
IWL_MEASURE_HISTOGRAM_RPI = (1 << 2),
IWL_MEASURE_HISTOGRAM_NOISE = (1 << 3),
IWL_MEASURE_FRAME = (1 << 4),
/* bits 5:6 are reserved */
IWL_MEASURE_IDLE = (1 << 7),
};
/*
* SPECTRUM_MEASURE_NOTIFICATION = 0x75 (notification only, not a command)
*/
struct iwl3945_spectrum_notification {
u8 id; /* measurement id -- 0 or 1 */
u8 token;
u8 channel_index; /* index in measurement channel list */
u8 state; /* 0 - start, 1 - stop */
__le32 start_time; /* lower 32-bits of TSF */
u8 band; /* 0 - 5.2GHz, 1 - 2.4GHz */
u8 channel;
u8 type; /* see enum iwl3945_measurement_type */
u8 reserved1;
/* NOTE: cca_ofdm, cca_cck, basic_type, and histogram are only only
* valid if applicable for measurement type requested. */
__le32 cca_ofdm; /* cca fraction time in 40Mhz clock periods */
__le32 cca_cck; /* cca fraction time in 44Mhz clock periods */
__le32 cca_time; /* channel load time in usecs */
u8 basic_type; /* 0 - bss, 1 - ofdm preamble, 2 -
* unidentified */
u8 reserved2[3];
struct iwl3945_measurement_histogram histogram;
__le32 stop_time; /* lower 32-bits of TSF */
__le32 status; /* see iwl3945_measurement_status */
} __attribute__ ((packed));
/******************************************************************************
* (7)
* Power Management Commands, Responses, Notifications:
*
*****************************************************************************/
/**
* struct iwl3945_powertable_cmd - Power Table Command
* @flags: See below:
*
* POWER_TABLE_CMD = 0x77 (command, has simple generic response)
*
* PM allow:
* bit 0 - '0' Driver not allow power management
* '1' Driver allow PM (use rest of parameters)
* uCode send sleep notifications:
* bit 1 - '0' Don't send sleep notification
* '1' send sleep notification (SEND_PM_NOTIFICATION)
* Sleep over DTIM
* bit 2 - '0' PM have to walk up every DTIM
* '1' PM could sleep over DTIM till listen Interval.
* PCI power managed
* bit 3 - '0' (PCI_LINK_CTRL & 0x1)
* '1' !(PCI_LINK_CTRL & 0x1)
* Force sleep Modes
* bit 31/30- '00' use both mac/xtal sleeps
* '01' force Mac sleep
* '10' force xtal sleep
* '11' Illegal set
*
* NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then
* ucode assume sleep over DTIM is allowed and we don't need to wakeup
* for every DTIM.
*/
#define IWL_POWER_VEC_SIZE 5
#define IWL_POWER_DRIVER_ALLOW_SLEEP_MSK cpu_to_le32(1 << 0)
#define IWL_POWER_SLEEP_OVER_DTIM_MSK cpu_to_le32(1 << 2)
#define IWL_POWER_PCI_PM_MSK cpu_to_le32(1 << 3)
struct iwl3945_powertable_cmd {
__le32 flags;
__le32 rx_data_timeout;
__le32 tx_data_timeout;
__le32 sleep_interval[IWL_POWER_VEC_SIZE];
} __attribute__((packed));
/*
* PM_SLEEP_NOTIFICATION = 0x7A (notification only, not a command)
* 3945 and 4965 identical.
*/
struct iwl3945_sleep_notification {
u8 pm_sleep_mode;
u8 pm_wakeup_src;
__le16 reserved;
__le32 sleep_time;
__le32 tsf_low;
__le32 bcon_timer;
} __attribute__ ((packed));
/* Sleep states. 3945 and 4965 identical. */
enum {
IWL_PM_NO_SLEEP = 0,
IWL_PM_SLP_MAC = 1,
IWL_PM_SLP_FULL_MAC_UNASSOCIATE = 2,
IWL_PM_SLP_FULL_MAC_CARD_STATE = 3,
IWL_PM_SLP_PHY = 4,
IWL_PM_SLP_REPENT = 5,
IWL_PM_WAKEUP_BY_TIMER = 6,
IWL_PM_WAKEUP_BY_DRIVER = 7,
IWL_PM_WAKEUP_BY_RFKILL = 8,
/* 3 reserved */
IWL_PM_NUM_OF_MODES = 12,
};
/*
* REPLY_CARD_STATE_CMD = 0xa0 (command, has simple generic response)
*/
#define CARD_STATE_CMD_DISABLE 0x00 /* Put card to sleep */
#define CARD_STATE_CMD_ENABLE 0x01 /* Wake up card */
#define CARD_STATE_CMD_HALT 0x02 /* Power down permanently */
struct iwl3945_card_state_cmd {
__le32 status; /* CARD_STATE_CMD_* request new power state */
} __attribute__ ((packed));
/*
* CARD_STATE_NOTIFICATION = 0xa1 (notification only, not a command)
*/
struct iwl3945_card_state_notif {
__le32 flags;
} __attribute__ ((packed));
#define HW_CARD_DISABLED 0x01
#define SW_CARD_DISABLED 0x02
#define RF_CARD_DISABLED 0x04
#define RXON_CARD_DISABLED 0x10
struct iwl3945_ct_kill_config {
__le32 reserved;
__le32 critical_temperature_M;
__le32 critical_temperature_R;
} __attribute__ ((packed));
/******************************************************************************
* (8)
* Scan Commands, Responses, Notifications:
*
*****************************************************************************/
/**
* struct iwl3945_scan_channel - entry in REPLY_SCAN_CMD channel table
*
* One for each channel in the scan list.
* Each channel can independently select:
* 1) SSID for directed active scans
* 2) Txpower setting (for rate specified within Tx command)
* 3) How long to stay on-channel (behavior may be modified by quiet_time,
* quiet_plcp_th, good_CRC_th)
*
* To avoid uCode errors, make sure the following are true (see comments
* under struct iwl3945_scan_cmd about max_out_time and quiet_time):
* 1) If using passive_dwell (i.e. passive_dwell != 0):
* active_dwell <= passive_dwell (< max_out_time if max_out_time != 0)
* 2) quiet_time <= active_dwell
* 3) If restricting off-channel time (i.e. max_out_time !=0):
* passive_dwell < max_out_time
* active_dwell < max_out_time
*/
struct iwl3945_scan_channel {
/*
* type is defined as:
* 0:0 1 = active, 0 = passive
* 1:4 SSID direct bit map; if a bit is set, then corresponding
* SSID IE is transmitted in probe request.
* 5:7 reserved
*/
u8 type;
u8 channel; /* band is selected by iwl3945_scan_cmd "flags" field */
struct iwl3945_tx_power tpc;
__le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
__le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
} __attribute__ ((packed));
/**
* struct iwl3945_ssid_ie - directed scan network information element
*
* Up to 4 of these may appear in REPLY_SCAN_CMD, selected by "type" field
* in struct iwl3945_scan_channel; each channel may select different ssids from
* among the 4 entries. SSID IEs get transmitted in reverse order of entry.
*/
struct iwl3945_ssid_ie {
u8 id;
u8 len;
u8 ssid[32];
} __attribute__ ((packed));
#define PROBE_OPTION_MAX 0x4
#define TX_CMD_LIFE_TIME_INFINITE cpu_to_le32(0xFFFFFFFF)
#define IWL_GOOD_CRC_TH cpu_to_le16(1)
#define IWL_MAX_SCAN_SIZE 1024
/*
* REPLY_SCAN_CMD = 0x80 (command)
*
* The hardware scan command is very powerful; the driver can set it up to
* maintain (relatively) normal network traffic while doing a scan in the
* background. The max_out_time and suspend_time control the ratio of how
* long the device stays on an associated network channel ("service channel")
* vs. how long it's away from the service channel, tuned to other channels
* for scanning.
*
* max_out_time is the max time off-channel (in usec), and suspend_time
* is how long (in "extended beacon" format) that the scan is "suspended"
* after returning to the service channel. That is, suspend_time is the
* time that we stay on the service channel, doing normal work, between
* scan segments. The driver may set these parameters differently to support
* scanning when associated vs. not associated, and light vs. heavy traffic
* loads when associated.
*
* After receiving this command, the device's scan engine does the following;
*
* 1) Sends SCAN_START notification to driver
* 2) Checks to see if it has time to do scan for one channel
* 3) Sends NULL packet, with power-save (PS) bit set to 1,
* to tell AP that we're going off-channel
* 4) Tunes to first channel in scan list, does active or passive scan
* 5) Sends SCAN_RESULT notification to driver
* 6) Checks to see if it has time to do scan on *next* channel in list
* 7) Repeats 4-6 until it no longer has time to scan the next channel
* before max_out_time expires
* 8) Returns to service channel
* 9) Sends NULL packet with PS=0 to tell AP that we're back
* 10) Stays on service channel until suspend_time expires
* 11) Repeats entire process 2-10 until list is complete
* 12) Sends SCAN_COMPLETE notification
*
* For fast, efficient scans, the scan command also has support for staying on
* a channel for just a short time, if doing active scanning and getting no
* responses to the transmitted probe request. This time is controlled by
* quiet_time, and the number of received packets below which a channel is
* considered "quiet" is controlled by quiet_plcp_threshold.
*
* For active scanning on channels that have regulatory restrictions against
* blindly transmitting, the scan can listen before transmitting, to make sure
* that there is already legitimate activity on the channel. If enough
* packets are cleanly received on the channel (controlled by good_CRC_th,
* typical value 1), the scan engine starts transmitting probe requests.
*
* Driver must use separate scan commands for 2.4 vs. 5 GHz bands.
*
* To avoid uCode errors, see timing restrictions described under
* struct iwl3945_scan_channel.
*/
struct iwl3945_scan_cmd {
__le16 len;
u8 reserved0;
u8 channel_count; /* # channels in channel list */
__le16 quiet_time; /* dwell only this # millisecs on quiet channel
* (only for active scan) */
__le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
__le16 good_CRC_th; /* passive -> active promotion threshold */
__le16 reserved1;
__le32 max_out_time; /* max usec to be away from associated (service)
* channel */
__le32 suspend_time; /* pause scan this long (in "extended beacon
* format") when returning to service channel:
* 3945; 31:24 # beacons, 19:0 additional usec,
* 4965; 31:22 # beacons, 21:0 additional usec.
*/
__le32 flags; /* RXON_FLG_* */
__le32 filter_flags; /* RXON_FILTER_* */
/* For active scans (set to all-0s for passive scans).
* Does not include payload. Must specify Tx rate; no rate scaling. */
struct iwl3945_tx_cmd tx_cmd;
/* For directed active scans (set to all-0s otherwise) */
struct iwl3945_ssid_ie direct_scan[PROBE_OPTION_MAX];
/*
* Probe request frame, followed by channel list.
*
* Size of probe request frame is specified by byte count in tx_cmd.
* Channel list follows immediately after probe request frame.
* Number of channels in list is specified by channel_count.
* Each channel in list is of type:
*
* struct iwl3945_scan_channel channels[0];
*
* NOTE: Only one band of channels can be scanned per pass. You
* must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
* for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
* before requesting another scan.
*/
u8 data[0];
} __attribute__ ((packed));
/* Can abort will notify by complete notification with abort status. */
#define CAN_ABORT_STATUS cpu_to_le32(0x1)
/* complete notification statuses */
#define ABORT_STATUS 0x2
/*
* REPLY_SCAN_CMD = 0x80 (response)
*/
struct iwl3945_scanreq_notification {
__le32 status; /* 1: okay, 2: cannot fulfill request */
} __attribute__ ((packed));
/*
* SCAN_START_NOTIFICATION = 0x82 (notification only, not a command)
*/
struct iwl3945_scanstart_notification {
__le32 tsf_low;
__le32 tsf_high;
__le32 beacon_timer;
u8 channel;
u8 band;
u8 reserved[2];
__le32 status;
} __attribute__ ((packed));
#define SCAN_OWNER_STATUS 0x1;
#define MEASURE_OWNER_STATUS 0x2;
#define NUMBER_OF_STATISTICS 1 /* first __le32 is good CRC */
/*
* SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
*/
struct iwl3945_scanresults_notification {
u8 channel;
u8 band;
u8 reserved[2];
__le32 tsf_low;
__le32 tsf_high;
__le32 statistics[NUMBER_OF_STATISTICS];
} __attribute__ ((packed));
/*
* SCAN_COMPLETE_NOTIFICATION = 0x84 (notification only, not a command)
*/
struct iwl3945_scancomplete_notification {
u8 scanned_channels;
u8 status;
u8 reserved;
u8 last_channel;
__le32 tsf_low;
__le32 tsf_high;
} __attribute__ ((packed));
/******************************************************************************
* (9)
* IBSS/AP Commands and Notifications:
*
*****************************************************************************/
/*
* BEACON_NOTIFICATION = 0x90 (notification only, not a command)
*/
struct iwl3945_beacon_notif {
struct iwl3945_tx_resp beacon_notify_hdr;
__le32 low_tsf;
__le32 high_tsf;
__le32 ibss_mgr_status;
} __attribute__ ((packed));
/*
* REPLY_TX_BEACON = 0x91 (command, has simple generic response)
*/
struct iwl3945_tx_beacon_cmd {
struct iwl3945_tx_cmd tx;
__le16 tim_idx;
u8 tim_size;
u8 reserved1;
struct ieee80211_hdr frame[0]; /* beacon frame */
} __attribute__ ((packed));
/******************************************************************************
* (10)
* Statistics Commands and Notifications:
*
*****************************************************************************/
#define IWL_TEMP_CONVERT 260
#define SUP_RATE_11A_MAX_NUM_CHANNELS 8
#define SUP_RATE_11B_MAX_NUM_CHANNELS 4
#define SUP_RATE_11G_MAX_NUM_CHANNELS 12
/* Used for passing to driver number of successes and failures per rate */
struct rate_histogram {
union {
__le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
__le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
__le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
} success;
union {
__le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
__le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
__le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
} failed;
} __attribute__ ((packed));
/* statistics command response */
struct statistics_rx_phy {
__le32 ina_cnt;
__le32 fina_cnt;
__le32 plcp_err;
__le32 crc32_err;
__le32 overrun_err;
__le32 early_overrun_err;
__le32 crc32_good;
__le32 false_alarm_cnt;
__le32 fina_sync_err_cnt;
__le32 sfd_timeout;
__le32 fina_timeout;
__le32 unresponded_rts;
__le32 rxe_frame_limit_overrun;
__le32 sent_ack_cnt;
__le32 sent_cts_cnt;
} __attribute__ ((packed));
struct statistics_rx_non_phy {
__le32 bogus_cts; /* CTS received when not expecting CTS */
__le32 bogus_ack; /* ACK received when not expecting ACK */
__le32 non_bssid_frames; /* number of frames with BSSID that
* doesn't belong to the STA BSSID */
__le32 filtered_frames; /* count frames that were dumped in the
* filtering process */
__le32 non_channel_beacons; /* beacons with our bss id but not on
* our serving channel */
} __attribute__ ((packed));
struct statistics_rx {
struct statistics_rx_phy ofdm;
struct statistics_rx_phy cck;
struct statistics_rx_non_phy general;
} __attribute__ ((packed));
struct statistics_tx {
__le32 preamble_cnt;
__le32 rx_detected_cnt;
__le32 bt_prio_defer_cnt;
__le32 bt_prio_kill_cnt;
__le32 few_bytes_cnt;
__le32 cts_timeout;
__le32 ack_timeout;
__le32 expected_ack_cnt;
__le32 actual_ack_cnt;
} __attribute__ ((packed));
struct statistics_dbg {
__le32 burst_check;
__le32 burst_count;
__le32 reserved[4];
} __attribute__ ((packed));
struct statistics_div {
__le32 tx_on_a;
__le32 tx_on_b;
__le32 exec_time;
__le32 probe_time;
} __attribute__ ((packed));
struct statistics_general {
__le32 temperature;
struct statistics_dbg dbg;
__le32 sleep_time;
__le32 slots_out;
__le32 slots_idle;
__le32 ttl_timestamp;
struct statistics_div div;
} __attribute__ ((packed));
/*
* REPLY_STATISTICS_CMD = 0x9c,
* 3945 and 4965 identical.
*
* This command triggers an immediate response containing uCode statistics.
* The response is in the same format as STATISTICS_NOTIFICATION 0x9d, below.
*
* If the CLEAR_STATS configuration flag is set, uCode will clear its
* internal copy of the statistics (counters) after issuing the response.
* This flag does not affect STATISTICS_NOTIFICATIONs after beacons (see below).
*
* If the DISABLE_NOTIF configuration flag is set, uCode will not issue
* STATISTICS_NOTIFICATIONs after received beacons (see below). This flag
* does not affect the response to the REPLY_STATISTICS_CMD 0x9c itself.
*/
#define IWL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
#define IWL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
struct iwl3945_statistics_cmd {
__le32 configuration_flags; /* IWL_STATS_CONF_* */
} __attribute__ ((packed));
/*
* STATISTICS_NOTIFICATION = 0x9d (notification only, not a command)
*
* By default, uCode issues this notification after receiving a beacon
* while associated. To disable this behavior, set DISABLE_NOTIF flag in the
* REPLY_STATISTICS_CMD 0x9c, above.
*
* Statistics counters continue to increment beacon after beacon, but are
* cleared when changing channels or when driver issues REPLY_STATISTICS_CMD
* 0x9c with CLEAR_STATS bit set (see above).
*
* uCode also issues this notification during scans. uCode clears statistics
* appropriately so that each notification contains statistics for only the
* one channel that has just been scanned.
*/
#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
#define STATISTICS_REPLY_FLG_FAT_MODE_MSK cpu_to_le32(0x8)
struct iwl3945_notif_statistics {
__le32 flag;
struct statistics_rx rx;
struct statistics_tx tx;
struct statistics_general general;
} __attribute__ ((packed));
/*
* MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
*/
/* if ucode missed CONSECUTIVE_MISSED_BCONS_TH beacons in a row,
* then this notification will be sent. */
#define CONSECUTIVE_MISSED_BCONS_TH 20
struct iwl3945_missed_beacon_notif {
__le32 consequtive_missed_beacons;
__le32 total_missed_becons;
__le32 num_expected_beacons;
__le32 num_recvd_beacons;
} __attribute__ ((packed));
/******************************************************************************
* (11)
* Rx Calibration Commands:
*
*****************************************************************************/
#define PHY_CALIBRATE_DIFF_GAIN_CMD (7)
#define HD_TABLE_SIZE (11)
struct iwl3945_sensitivity_cmd {
__le16 control;
__le16 table[HD_TABLE_SIZE];
} __attribute__ ((packed));
struct iwl3945_calibration_cmd {
u8 opCode;
u8 flags;
__le16 reserved;
s8 diff_gain_a;
s8 diff_gain_b;
s8 diff_gain_c;
u8 reserved1;
} __attribute__ ((packed));
/******************************************************************************
* (12)
* Miscellaneous Commands:
*
*****************************************************************************/
/*
* LEDs Command & Response
* REPLY_LEDS_CMD = 0x48 (command, has simple generic response)
*
* For each of 3 possible LEDs (Activity/Link/Tech, selected by "id" field),
* this command turns it on or off, or sets up a periodic blinking cycle.
*/
struct iwl3945_led_cmd {
__le32 interval; /* "interval" in uSec */
u8 id; /* 1: Activity, 2: Link, 3: Tech */
u8 off; /* # intervals off while blinking;
* "0", with >0 "on" value, turns LED on */
u8 on; /* # intervals on while blinking;
* "0", regardless of "off", turns LED off */
u8 reserved;
} __attribute__ ((packed));
/******************************************************************************
* (13)
* Union of all expected notifications/responses:
*
*****************************************************************************/
struct iwl3945_rx_packet {
__le32 len;
struct iwl3945_cmd_header hdr;
union {
struct iwl3945_alive_resp alive_frame;
struct iwl3945_rx_frame rx_frame;
struct iwl3945_tx_resp tx_resp;
struct iwl3945_spectrum_notification spectrum_notif;
struct iwl3945_csa_notification csa_notif;
struct iwl3945_error_resp err_resp;
struct iwl3945_card_state_notif card_state_notif;
struct iwl3945_beacon_notif beacon_status;
struct iwl3945_add_sta_resp add_sta;
struct iwl3945_sleep_notification sleep_notif;
struct iwl3945_spectrum_resp spectrum;
struct iwl3945_notif_statistics stats;
__le32 status;
u8 raw[0];
} u;
} __attribute__ ((packed));
#define IWL_RX_FRAME_SIZE (4 + sizeof(struct iwl3945_rx_frame))
#endif /* __iwl3945_3945_commands_h__ */
