#ifndef B43_H_
#define B43_H_
#include <linux/kernel.h>
#include <linux/spinlock.h>
#include <linux/interrupt.h>
#include <linux/hw_random.h>
#include <linux/ssb/ssb.h>
#include <net/mac80211.h>
#include "debugfs.h"
#include "leds.h"
#include "rfkill.h"
#include "lo.h"
#include "phy_common.h"
/* The unique identifier of the firmware that's officially supported by
* this driver version. */
#define B43_SUPPORTED_FIRMWARE_ID "FW13"
#ifdef CONFIG_B43_DEBUG
# define B43_DEBUG 1
#else
# define B43_DEBUG 0
#endif
#define B43_RX_MAX_SSI 60
/* MMIO offsets */
#define B43_MMIO_DMA0_REASON 0x20
#define B43_MMIO_DMA0_IRQ_MASK 0x24
#define B43_MMIO_DMA1_REASON 0x28
#define B43_MMIO_DMA1_IRQ_MASK 0x2C
#define B43_MMIO_DMA2_REASON 0x30
#define B43_MMIO_DMA2_IRQ_MASK 0x34
#define B43_MMIO_DMA3_REASON 0x38
#define B43_MMIO_DMA3_IRQ_MASK 0x3C
#define B43_MMIO_DMA4_REASON 0x40
#define B43_MMIO_DMA4_IRQ_MASK 0x44
#define B43_MMIO_DMA5_REASON 0x48
#define B43_MMIO_DMA5_IRQ_MASK 0x4C
#define B43_MMIO_MACCTL 0x120 /* MAC control */
#define B43_MMIO_MACCMD 0x124 /* MAC command */
#define B43_MMIO_GEN_IRQ_REASON 0x128
#define B43_MMIO_GEN_IRQ_MASK 0x12C
#define B43_MMIO_RAM_CONTROL 0x130
#define B43_MMIO_RAM_DATA 0x134
#define B43_MMIO_PS_STATUS 0x140
#define B43_MMIO_RADIO_HWENABLED_HI 0x158
#define B43_MMIO_SHM_CONTROL 0x160
#define B43_MMIO_SHM_DATA 0x164
#define B43_MMIO_SHM_DATA_UNALIGNED 0x166
#define B43_MMIO_XMITSTAT_0 0x170
#define B43_MMIO_XMITSTAT_1 0x174
#define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
#define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
#define B43_MMIO_TSF_CFP_REP 0x188
#define B43_MMIO_TSF_CFP_START 0x18C
#define B43_MMIO_TSF_CFP_MAXDUR 0x190
/* 32-bit DMA */
#define B43_MMIO_DMA32_BASE0 0x200
#define B43_MMIO_DMA32_BASE1 0x220
#define B43_MMIO_DMA32_BASE2 0x240
#define B43_MMIO_DMA32_BASE3 0x260
#define B43_MMIO_DMA32_BASE4 0x280
#define B43_MMIO_DMA32_BASE5 0x2A0
/* 64-bit DMA */
#define B43_MMIO_DMA64_BASE0 0x200
#define B43_MMIO_DMA64_BASE1 0x240
#define B43_MMIO_DMA64_BASE2 0x280
#define B43_MMIO_DMA64_BASE3 0x2C0
#define B43_MMIO_DMA64_BASE4 0x300
#define B43_MMIO_DMA64_BASE5 0x340
/* PIO on core rev < 11 */
#define B43_MMIO_PIO_BASE0 0x300
#define B43_MMIO_PIO_BASE1 0x310
#define B43_MMIO_PIO_BASE2 0x320
#define B43_MMIO_PIO_BASE3 0x330
#define B43_MMIO_PIO_BASE4 0x340
#define B43_MMIO_PIO_BASE5 0x350
#define B43_MMIO_PIO_BASE6 0x360
#define B43_MMIO_PIO_BASE7 0x370
/* PIO on core rev >= 11 */
#define B43_MMIO_PIO11_BASE0 0x200
#define B43_MMIO_PIO11_BASE1 0x240
#define B43_MMIO_PIO11_BASE2 0x280
#define B43_MMIO_PIO11_BASE3 0x2C0
#define B43_MMIO_PIO11_BASE4 0x300
#define B43_MMIO_PIO11_BASE5 0x340
#define B43_MMIO_PHY_VER 0x3E0
#define B43_MMIO_PHY_RADIO 0x3E2
#define B43_MMIO_PHY0 0x3E6
#define B43_MMIO_ANTENNA 0x3E8
#define B43_MMIO_CHANNEL 0x3F0
#define B43_MMIO_CHANNEL_EXT 0x3F4
#define B43_MMIO_RADIO_CONTROL 0x3F6
#define B43_MMIO_RADIO_DATA_HIGH 0x3F8
#define B43_MMIO_RADIO_DATA_LOW 0x3FA
#define B43_MMIO_PHY_CONTROL 0x3FC
#define B43_MMIO_PHY_DATA 0x3FE
#define B43_MMIO_MACFILTER_CONTROL 0x420
#define B43_MMIO_MACFILTER_DATA 0x422
#define B43_MMIO_RCMTA_COUNT 0x43C
#define B43_MMIO_RADIO_HWENABLED_LO 0x49A
#define B43_MMIO_GPIO_CONTROL 0x49C
#define B43_MMIO_GPIO_MASK 0x49E
#define B43_MMIO_TSF_CFP_START_LOW 0x604
#define B43_MMIO_TSF_CFP_START_HIGH 0x606
#define B43_MMIO_TSF_CFP_PRETBTT 0x612
#define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */
#define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */
#define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */
#define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */
#define B43_MMIO_RNG 0x65A
#define B43_MMIO_IFSCTL 0x688 /* Interframe space control */
#define B43_MMIO_IFSCTL_USE_EDCF 0x0004
#define B43_MMIO_POWERUP_DELAY 0x6A8
#define B43_MMIO_BTCOEX_CTL 0x6B4 /* Bluetooth Coexistence Control */
#define B43_MMIO_BTCOEX_STAT 0x6B6 /* Bluetooth Coexistence Status */
#define B43_MMIO_BTCOEX_TXCTL 0x6B8 /* Bluetooth Coexistence Transmit Control */
/* SPROM boardflags_lo values */
#define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
#define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
#define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
#define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
#define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
#define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
#define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
#define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */
#define B43_BFL_ENETVLAN 0x0100 /* can do vlan */
#define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
#define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */
#define B43_BFL_FEM 0x0800 /* supports the Front End Module */
#define B43_BFL_EXTLNA 0x1000 /* has an external LNA */
#define B43_BFL_HGPA 0x2000 /* had high gain PA */
#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
/* SPROM boardflags_hi values */
#define B43_BFH_NOPA 0x0001 /* has no PA */
#define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */
#define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */
#define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared
* with bluetooth */
#define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */
#define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */
#define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna
* with bluetooth */
/* GPIO register offset, in both ChipCommon and PCI core. */
#define B43_GPIO_CONTROL 0x6c
/* SHM Routing */
enum {
B43_SHM_UCODE, /* Microcode memory */
B43_SHM_SHARED, /* Shared memory */
B43_SHM_SCRATCH, /* Scratch memory */
B43_SHM_HW, /* Internal hardware register */
B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */
};
/* SHM Routing modifiers */
#define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */
#define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */
#define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \
B43_SHM_AUTOINC_W)
/* Misc SHM_SHARED offsets */
#define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */
#define B43_SHM_SH_PCTLWDPOS 0x0008
#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
#define B43_SHM_SH_FWCAPA 0x0042 /* Firmware capabilities (Opensource firmware only) */
#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
#define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */
#define B43_SHM_SH_HOSTFMI 0x0060 /* Hostflags for ucode options (middle) */
#define B43_SHM_SH_HOSTFHI 0x0062 /* Hostflags for ucode options (high) */
#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
#define B43_SHM_SH_RADAR 0x0066 /* Radar register */
#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5Ghz channel */
#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
/* TSSI information */
#define B43_SHM_SH_TSSI_CCK 0x0058 /* TSSI for last 4 CCK frames (32bit) */
#define B43_SHM_SH_TSSI_OFDM_A 0x0068 /* TSSI for last 4 OFDM frames (32bit) */
#define B43_SHM_SH_TSSI_OFDM_G 0x0070 /* TSSI for last 4 OFDM frames (32bit) */
#define B43_TSSI_MAX 0x7F /* Max value for one TSSI value */
/* SHM_SHARED TX FIFO variables */
#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
#define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */
#define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */
/* SHM_SHARED background noise */
#define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */
#define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */
#define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */
/* SHM_SHARED crypto engine */
#define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */
#define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */
#define B43_SHM_SH_KTP 0x0056 /* Key table pointer */
#define B43_SHM_SH_TKIPTSCTTAK 0x0318
#define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */
#define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */
/* SHM_SHARED WME variables */
#define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */
#define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */
#define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */
/* SHM_SHARED powersave mode related */
#define B43_SHM_SH_SLOTT 0x0010 /* Slot time */
#define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */
#define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */
/* SHM_SHARED beacon/AP variables */
#define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */
#define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */
#define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */
#define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */
#define B43_SHM_SH_DTIMP 0x0012 /* DTIP period */
#define B43_SHM_SH_MCASTCOOKIE 0x00A8 /* Last bcast/mcast frame ID */
#define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */
#define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */
#define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */
#define B43_SHM_SH_EXTNPHYCTL 0x00B0 /* Extended bytes for beacon PHY control (N) */
/* SHM_SHARED ACK/CTS control */
#define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */
/* SHM_SHARED probe response variables */
#define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */
#define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */
#define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */
#define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */
#define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */
/* SHM_SHARED rate tables */
#define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */
#define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */
#define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */
#define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */
/* SHM_SHARED microcode soft registers */
#define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */
#define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */
#define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */
#define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */
#define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */
#define B43_SHM_SH_UCODESTAT_INVALID 0
#define B43_SHM_SH_UCODESTAT_INIT 1
#define B43_SHM_SH_UCODESTAT_ACTIVE 2
#define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */
#define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */
#define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */
#define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */
#define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */
/* SHM_SCRATCH offsets */
#define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */
#define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */
#define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */
#define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */
#define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */
#define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */
#define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */
#define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */
#define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */
#define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */
/* Hardware Radio Enable masks */
#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
/* HostFlags. See b43_hf_read/write() */
#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */
#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */
#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */
#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */
#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */
#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */
#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */
#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */
#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */
#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */
#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */
#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */
#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */
#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */
#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */
#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */
#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */
#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */
#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */
#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */
#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */
#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */
#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */
#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */
#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */
#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */
#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */
#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */
#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */
#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */
#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */
#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */
#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */
#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */
#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */
/* Firmware capabilities field in SHM (Opensource firmware only) */
#define B43_FWCAPA_HWCRYPTO 0x0001
#define B43_FWCAPA_QOS 0x0002
/* MacFilter offsets. */
#define B43_MACFILTER_SELF 0x0000
#define B43_MACFILTER_BSSID 0x0003
/* PowerControl */
#define B43_PCTL_IN 0xB0
#define B43_PCTL_OUT 0xB4
#define B43_PCTL_OUTENABLE 0xB8
#define B43_PCTL_XTAL_POWERUP 0x40
#define B43_PCTL_PLL_POWERDOWN 0x80
/* PowerControl Clock Modes */
#define B43_PCTL_CLK_FAST 0x00
#define B43_PCTL_CLK_SLOW 0x01
#define B43_PCTL_CLK_DYNAMIC 0x02
#define B43_PCTL_FORCE_SLOW 0x0800
#define B43_PCTL_FORCE_PLL 0x1000
#define B43_PCTL_DYN_XTAL 0x2000
/* PHYVersioning */
#define B43_PHYTYPE_A 0x00
#define B43_PHYTYPE_B 0x01
#define B43_PHYTYPE_G 0x02
#define B43_PHYTYPE_N 0x04
#define B43_PHYTYPE_LP 0x05
/* PHYRegisters */
#define B43_PHY_ILT_A_CTRL 0x0072
#define B43_PHY_ILT_A_DATA1 0x0073
#define B43_PHY_ILT_A_DATA2 0x0074
#define B43_PHY_G_LO_CONTROL 0x0810
#define B43_PHY_ILT_G_CTRL 0x0472
#define B43_PHY_ILT_G_DATA1 0x0473
#define B43_PHY_ILT_G_DATA2 0x0474
#define B43_PHY_A_PCTL 0x007B
#define B43_PHY_G_PCTL 0x0029
#define B43_PHY_A_CRS 0x0029
#define B43_PHY_RADIO_BITFIELD 0x0401
#define B43_PHY_G_CRS 0x0429
#define B43_PHY_NRSSILT_CTRL 0x0803
#define B43_PHY_NRSSILT_DATA 0x0804
/* RadioRegisters */
#define B43_RADIOCTL_ID 0x01
/* MAC Control bitfield */
#define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */
#define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */
#define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */
#define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */
#define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */
#define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */
#define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */
#define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */
#define B43_MACCTL_BE 0x00010000 /* Big Endian mode */
#define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */
#define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */
#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
#define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */
#define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */
#define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */
#define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */
#define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */
#define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */
#define B43_MACCTL_GMODE 0x80000000 /* G Mode */
/* MAC Command bitfield */
#define B43_MACCMD_BEACON0_VALID 0x00000001 /* Beacon 0 in template RAM is busy/valid */
#define B43_MACCMD_BEACON1_VALID 0x00000002 /* Beacon 1 in template RAM is busy/valid */
#define B43_MACCMD_DFQ_VALID 0x00000004 /* Directed frame queue valid (IBSS PS mode, ATIM) */
#define B43_MACCMD_CCA 0x00000008 /* Clear channel assessment */
#define B43_MACCMD_BGNOISE 0x00000010 /* Background noise */
/* 802.11 core specific TM State Low (SSB_TMSLOW) flags */
#define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */
#define B43_TMSLOW_PHYCLKSPEED 0x00C00000 /* PHY clock speed mask (N-PHY only) */
#define B43_TMSLOW_PHYCLKSPEED_40MHZ 0x00000000 /* 40 MHz PHY */
#define B43_TMSLOW_PHYCLKSPEED_80MHZ 0x00400000 /* 80 MHz PHY */
#define B43_TMSLOW_PHYCLKSPEED_160MHZ 0x00800000 /* 160 MHz PHY */
#define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select (rev >= 5) */
#define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */
#define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */
#define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */
/* 802.11 core specific TM State High (SSB_TMSHIGH) flags */
#define B43_TMSHIGH_DUALBAND_PHY 0x00080000 /* Dualband PHY available */
#define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */
#define B43_TMSHIGH_HAVE_5GHZ_PHY 0x00020000 /* 5 GHz PHY available (rev >= 5) */
#define B43_TMSHIGH_HAVE_2GHZ_PHY 0x00010000 /* 2.4 GHz PHY available (rev >= 5) */
/* Generic-Interrupt reasons. */
#define B43_IRQ_MAC_SUSPENDED 0x00000001
#define B43_IRQ_BEACON 0x00000002
#define B43_IRQ_TBTT_INDI 0x00000004
#define B43_IRQ_BEACON_TX_OK 0x00000008
#define B43_IRQ_BEACON_CANCEL 0x00000010
#define B43_IRQ_ATIM_END 0x00000020
#define B43_IRQ_PMQ 0x00000040
#define B43_IRQ_PIO_WORKAROUND 0x00000100
#define B43_IRQ_MAC_TXERR 0x00000200
#define B43_IRQ_PHY_TXERR 0x00000800
#define B43_IRQ_PMEVENT 0x00001000
#define B43_IRQ_TIMER0 0x00002000
#define B43_IRQ_TIMER1 0x00004000
#define B43_IRQ_DMA 0x00008000
#define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000
#define B43_IRQ_CCA_MEASURE_OK 0x00020000
#define B43_IRQ_NOISESAMPLE_OK 0x00040000
#define B43_IRQ_UCODE_DEBUG 0x08000000
#define B43_IRQ_RFKILL 0x10000000
#define B43_IRQ_TX_OK 0x20000000
#define B43_IRQ_PHY_G_CHANGED 0x40000000
#define B43_IRQ_TIMEOUT 0x80000000
#define B43_IRQ_ALL 0xFFFFFFFF
#define B43_IRQ_MASKTEMPLATE (B43_IRQ_TBTT_INDI | \
B43_IRQ_ATIM_END | \
B43_IRQ_PMQ | \
B43_IRQ_MAC_TXERR | \
B43_IRQ_PHY_TXERR | \
B43_IRQ_DMA | \
B43_IRQ_TXFIFO_FLUSH_OK | \
B43_IRQ_NOISESAMPLE_OK | \
B43_IRQ_UCODE_DEBUG | \
B43_IRQ_RFKILL | \
B43_IRQ_TX_OK)
/* The firmware register to fetch the debug-IRQ reason from. */
#define B43_DEBUGIRQ_REASON_REG 63
/* Debug-IRQ reasons. */
#define B43_DEBUGIRQ_PANIC 0 /* The firmware panic'ed */
#define B43_DEBUGIRQ_DUMP_SHM 1 /* Dump shared SHM */
#define B43_DEBUGIRQ_DUMP_REGS 2 /* Dump the microcode registers */
#define B43_DEBUGIRQ_MARKER 3 /* A "marker" was thrown by the firmware. */
#define B43_DEBUGIRQ_ACK 0xFFFF /* The host writes that to ACK the IRQ */
/* The firmware register that contains the "marker" line. */
#define B43_MARKER_ID_REG 2
#define B43_MARKER_LINE_REG 3
/* The firmware register to fetch the panic reason from. */
#define B43_FWPANIC_REASON_REG 3
/* Firmware panic reason codes */
#define B43_FWPANIC_DIE 0 /* Firmware died. Don't auto-restart it. */
#define B43_FWPANIC_RESTART 1 /* Firmware died. Schedule a controller reset. */
/* The firmware register that contains the watchdog counter. */
#define B43_WATCHDOG_REG 1
/* Device specific rate values.
* The actual values defined here are (rate_in_mbps * 2).
* Some code depends on this. Don't change it. */
#define B43_CCK_RATE_1MB 0x02
#define B43_CCK_RATE_2MB 0x04
#define B43_CCK_RATE_5MB 0x0B
#define B43_CCK_RATE_11MB 0x16
#define B43_OFDM_RATE_6MB 0x0C
#define B43_OFDM_RATE_9MB 0x12
#define B43_OFDM_RATE_12MB 0x18
#define B43_OFDM_RATE_18MB 0x24
#define B43_OFDM_RATE_24MB 0x30
#define B43_OFDM_RATE_36MB 0x48
#define B43_OFDM_RATE_48MB 0x60
#define B43_OFDM_RATE_54MB 0x6C
/* Convert a b43 rate value to a rate in 100kbps */
#define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2)
#define B43_DEFAULT_SHORT_RETRY_LIMIT 7
#define B43_DEFAULT_LONG_RETRY_LIMIT 4
#define B43_PHY_TX_BADNESS_LIMIT 1000
/* Max size of a security key */
#define B43_SEC_KEYSIZE 16
/* Max number of group keys */
#define B43_NR_GROUP_KEYS 4
/* Max number of pairwise keys */
#define B43_NR_PAIRWISE_KEYS 50
/* Security algorithms. */
enum {
B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
B43_SEC_ALGO_WEP40,
B43_SEC_ALGO_TKIP,
B43_SEC_ALGO_AES,
B43_SEC_ALGO_WEP104,
B43_SEC_ALGO_AES_LEGACY,
};
struct b43_dmaring;
/* The firmware file header */
#define B43_FW_TYPE_UCODE 'u'
#define B43_FW_TYPE_PCM 'p'
#define B43_FW_TYPE_IV 'i'
struct b43_fw_header {
/* File type */
u8 type;
/* File format version */
u8 ver;
u8 __padding[2];
/* Size of the data. For ucode and PCM this is in bytes.
* For IV this is number-of-ivs. */
__be32 size;
} __attribute__((__packed__));
/* Initial Value file format */
#define B43_IV_OFFSET_MASK 0x7FFF
#define B43_IV_32BIT 0x8000
struct b43_iv {
__be16 offset_size;
union {
__be16 d16;
__be32 d32;
} data __attribute__((__packed__));
} __attribute__((__packed__));
/* Data structures for DMA transmission, per 80211 core. */
struct b43_dma {
struct b43_dmaring *tx_ring_AC_BK; /* Background */
struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */
struct b43_dmaring *tx_ring_AC_VI; /* Video */
struct b43_dmaring *tx_ring_AC_VO; /* Voice */
struct b43_dmaring *tx_ring_mcast; /* Multicast */
struct b43_dmaring *rx_ring;
};
struct b43_pio_txqueue;
struct b43_pio_rxqueue;
/* Data structures for PIO transmission, per 80211 core. */
struct b43_pio {
struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */
struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */
struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */
struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */
struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */
struct b43_pio_rxqueue *rx_queue;
};
/* Context information for a noise calculation (Link Quality). */
struct b43_noise_calculation {
bool calculation_running;
u8 nr_samples;
s8 samples[8][4];
};
struct b43_stats {
u8 link_noise;
};
struct b43_key {
/* If keyconf is NULL, this key is disabled.
* keyconf is a cookie. Don't derefenrence it outside of the set_key
* path, because b43 doesn't own it. */
struct ieee80211_key_conf *keyconf;
u8 algorithm;
};
/* SHM offsets to the QOS data structures for the 4 different queues. */
#define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \
(B43_NR_QOSPARAMS * sizeof(u16) * (queue)))
#define B43_QOS_BACKGROUND B43_QOS_PARAMS(0)
#define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1)
#define B43_QOS_VIDEO B43_QOS_PARAMS(2)
#define B43_QOS_VOICE B43_QOS_PARAMS(3)
/* QOS parameter hardware data structure offsets. */
#define B43_NR_QOSPARAMS 16
enum {
B43_QOSPARAM_TXOP = 0,
B43_QOSPARAM_CWMIN,
B43_QOSPARAM_CWMAX,
B43_QOSPARAM_CWCUR,
B43_QOSPARAM_AIFS,
B43_QOSPARAM_BSLOTS,
B43_QOSPARAM_REGGAP,
B43_QOSPARAM_STATUS,
};
/* QOS parameters for a queue. */
struct b43_qos_params {
/* The QOS parameters */
struct ieee80211_tx_queue_params p;
};
struct b43_wl;
/* The type of the firmware file. */
enum b43_firmware_file_type {
B43_FWTYPE_PROPRIETARY,
B43_FWTYPE_OPENSOURCE,
B43_NR_FWTYPES,
};
/* Context data for fetching firmware. */
struct b43_request_fw_context {
/* The device we are requesting the fw for. */
struct b43_wldev *dev;
/* The type of firmware to request. */
enum b43_firmware_file_type req_type;
/* Error messages for each firmware type. */
char errors[B43_NR_FWTYPES][128];
/* Temporary buffer for storing the firmware name. */
char fwname[64];
/* A fatal error occured while requesting. Firmware reqest
* can not continue, as any other reqest will also fail. */
int fatal_failure;
};
/* In-memory representation of a cached microcode file. */
struct b43_firmware_file {
const char *filename;
const struct firmware *data;
/* Type of the firmware file name. Note that this does only indicate
* the type by the firmware name. NOT the file contents.
* If you want to check for proprietary vs opensource, use (struct b43_firmware)->opensource
* instead! The (struct b43_firmware)->opensource flag is derived from the actual firmware
* binary code, not just the filename.
*/
enum b43_firmware_file_type type;
};
/* Pointers to the firmware data and meta information about it. */
struct b43_firmware {
/* Microcode */
struct b43_firmware_file ucode;
/* PCM code */
struct b43_firmware_file pcm;
/* Initial MMIO values for the firmware */
struct b43_firmware_file initvals;
/* Initial MMIO values for the firmware, band-specific */
struct b43_firmware_file initvals_band;
/* Firmware revision */
u16 rev;
/* Firmware patchlevel */
u16 patch;
/* Set to true, if we are using an opensource firmware.
* Use this to check for proprietary vs opensource. */
bool opensource;
/* Set to true, if the core needs a PCM firmware, but
* we failed to load one. This is always false for
* core rev > 10, as these don't need PCM firmware. */
bool pcm_request_failed;
};
/* Device (802.11 core) initialization status. */
enum {
B43_STAT_UNINIT = 0, /* Uninitialized. */
B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */
B43_STAT_STARTED = 2, /* Up and running. */
};
#define b43_status(wldev) atomic_read(&(wldev)->__init_status)
#define b43_set_status(wldev, stat) do { \
atomic_set(&(wldev)->__init_status, (stat)); \
smp_wmb(); \
} while (0)
/* Data structure for one wireless device (802.11 core) */
struct b43_wldev {
struct ssb_device *dev;
struct b43_wl *wl;
/* The device initialization status.
* Use b43_status() to query. */
atomic_t __init_status;
bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */
bool radio_hw_enable; /* saved state of radio hardware enabled state */
bool qos_enabled; /* TRUE, if QoS is used. */
bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */
/* PHY/Radio device. */
struct b43_phy phy;
union {
/* DMA engines. */
struct b43_dma dma;
/* PIO engines. */
struct b43_pio pio;
};
/* Use b43_using_pio_transfers() to check whether we are using
* DMA or PIO data transfers. */
bool __using_pio_transfers;
/* Various statistics about the physical device. */
struct b43_stats stats;
/* Reason code of the last interrupt. */
u32 irq_reason;
u32 dma_reason[6];
/* The currently active generic-interrupt mask. */
u32 irq_mask;
/* Link Quality calculation context. */
struct b43_noise_calculation noisecalc;
/* if > 0 MAC is suspended. if == 0 MAC is enabled. */
int mac_suspended;
/* Periodic tasks */
struct delayed_work periodic_work;
unsigned int periodic_state;
struct work_struct restart_work;
/* encryption/decryption */
u16 ktp; /* Key table pointer */
struct b43_key key[B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS];
/* Firmware data */
struct b43_firmware fw;
/* Devicelist in struct b43_wl (all 802.11 cores) */
struct list_head list;
/* Debugging stuff follows. */
#ifdef CONFIG_B43_DEBUG
struct b43_dfsentry *dfsentry;
unsigned int irq_count;
unsigned int irq_bit_count[32];
unsigned int tx_count;
unsigned int rx_count;
#endif
};
/*
* Include goes here to avoid a dependency problem.
* A better fix would be to integrate xmit.h into b43.h.
*/
#include "xmit.h"
/* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */
struct b43_wl {
/* Pointer to the active wireless device on this chip */
struct b43_wldev *current_dev;
/* Pointer to the ieee80211 hardware data structure */
struct ieee80211_hw *hw;
/* Global driver mutex. Every operation must run with this mutex locked. */
struct mutex mutex;
/* Hard-IRQ spinlock. This lock protects things used in the hard-IRQ
* handler, only. This basically is just the IRQ mask register. */
spinlock_t hardirq_lock;
/* The number of queues that were registered with the mac80211 subsystem
* initially. This is a backup copy of hw->queues in case hw->queues has
* to be dynamically lowered at runtime (Firmware does not support QoS).
* hw->queues has to be restored to the original value before unregistering
* from the mac80211 subsystem. */
u16 mac80211_initially_registered_queues;
/* We can only have one operating interface (802.11 core)
* at a time. General information about this interface follows.
*/
struct ieee80211_vif *vif;
/* The MAC address of the operating interface. */
u8 mac_addr[ETH_ALEN];
/* Current BSSID */
u8 bssid[ETH_ALEN];
/* Interface type. (NL80211_IFTYPE_XXX) */
int if_type;
/* Is the card operating in AP, STA or IBSS mode? */
bool operating;
/* filter flags */
unsigned int filter_flags;
/* Stats about the wireless interface */
struct ieee80211_low_level_stats ieee_stats;
#ifdef CONFIG_B43_HWRNG
struct hwrng rng;
bool rng_initialized;
char rng_name[30 + 1];
#endif /* CONFIG_B43_HWRNG */
/* List of all wireless devices on this chip */
struct list_head devlist;
u8 nr_devs;
bool radiotap_enabled;
bool radio_enabled;
/* The beacon we are currently using (AP or IBSS mode). */
struct sk_buff *current_beacon;
bool beacon0_uploaded;
bool beacon1_uploaded;
bool beacon_templates_virgin; /* Never wrote the templates? */
struct work_struct beacon_update_trigger;
/* The current QOS parameters for the 4 queues. */
struct b43_qos_params qos_params[4];
/* Work for adjustment of the transmission power.
* This is scheduled when we determine that the actual TX output
* power doesn't match what we want. */
struct work_struct txpower_adjust_work;
/* Packet transmit work */
struct work_struct tx_work;
/* Queue of packets to be transmitted. */
struct sk_buff_head tx_queue;
/* The device LEDs. */
struct b43_leds leds;
#ifdef CONFIG_B43_PIO
/*
* RX/TX header/tail buffers used by the frame transmit functions.
*/
struct b43_rxhdr_fw4 rxhdr;
struct b43_txhdr txhdr;
u8 rx_tail[4];
u8 tx_tail[4];
#endif /* CONFIG_B43_PIO */
};
static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw)
{
return hw->priv;
}
static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev)
{
struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
return ssb_get_drvdata(ssb_dev);
}
/* Is the device operating in a specified mode (NL80211_IFTYPE_XXX). */
static inline int b43_is_mode(struct b43_wl *wl, int type)
{
return (wl->operating && wl->if_type == type);
}
/**
* b43_current_band - Returns the currently used band.
* Returns one of IEEE80211_BAND_2GHZ and IEEE80211_BAND_5GHZ.
*/
static inline enum ieee80211_band b43_current_band(struct b43_wl *wl)
{
return wl->hw->conf.channel->band;
}
static inline u16 b43_read16(struct b43_wldev *dev, u16 offset)
{
return ssb_read16(dev->dev, offset);
}
static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value)
{
ssb_write16(dev->dev, offset, value);
}
static inline u32 b43_read32(struct b43_wldev *dev, u16 offset)
{
return ssb_read32(dev->dev, offset);
}
static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value)
{
ssb_write32(dev->dev, offset, value);
}
static inline bool b43_using_pio_transfers(struct b43_wldev *dev)
{
#ifdef CONFIG_B43_PIO
return dev->__using_pio_transfers;
#else
return 0;
#endif
}
#ifdef CONFIG_B43_FORCE_PIO
# define B43_FORCE_PIO 1
#else
# define B43_FORCE_PIO 0
#endif
/* Message printing */
void b43info(struct b43_wl *wl, const char *fmt, ...)
__attribute__ ((format(printf, 2, 3)));
void b43err(struct b43_wl *wl, const char *fmt, ...)
__attribute__ ((format(printf, 2, 3)));
void b43warn(struct b43_wl *wl, const char *fmt, ...)
__attribute__ ((format(printf, 2, 3)));
void b43dbg(struct b43_wl *wl, const char *fmt, ...)
__attribute__ ((format(printf, 2, 3)));
/* A WARN_ON variant that vanishes when b43 debugging is disabled.
* This _also_ evaluates the arg with debugging disabled. */
#if B43_DEBUG
# define B43_WARN_ON(x) WARN_ON(x)
#else
static inline bool __b43_warn_on_dummy(bool x) { return x; }
# define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x)))
#endif
/* Convert an integer to a Q5.2 value */
#define INT_TO_Q52(i) ((i) << 2)
/* Convert a Q5.2 value to an integer (precision loss!) */
#define Q52_TO_INT(q52) ((q52) >> 2)
/* Macros for printing a value in Q5.2 format */
#define Q52_FMT "%u.%u"
#define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4)
#endif /* B43_H_ */
