/*
* Comtrol SV11 card driver
*
* This is a slightly odd Z85230 synchronous driver. All you need to
* know basically is
*
* Its a genuine Z85230
*
* It supports DMA using two DMA channels in SYNC mode. The driver doesn't
* use these facilities
*
* The control port is at io+1, the data at io+3 and turning off the DMA
* is done by writing 0 to io+4
*
* The hardware does the bus handling to avoid the need for delays between
* touching control registers.
*
* Port B isnt wired (why - beats me)
*
* Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/mm.h>
#include <linux/net.h>
#include <linux/skbuff.h>
#include <linux/netdevice.h>
#include <linux/if_arp.h>
#include <linux/delay.h>
#include <linux/hdlc.h>
#include <linux/ioport.h>
#include <net/arp.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/byteorder.h>
#include "z85230.h"
static int dma;
/*
* Network driver support routines
*/
static inline struct z8530_dev* dev_to_sv(struct net_device *dev)
{
return (struct z8530_dev *)dev_to_hdlc(dev)->priv;
}
/*
* Frame receive. Simple for our card as we do HDLC and there
* is no funny garbage involved
*/
static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
{
/* Drop the CRC - it's not a good idea to try and negotiate it ;) */
skb_trim(skb, skb->len - 2);
skb->protocol = hdlc_type_trans(skb, c->netdevice);
skb_reset_mac_header(skb);
skb->dev = c->netdevice;
/*
* Send it to the PPP layer. We don't have time to process
* it right now.
*/
netif_rx(skb);
c->netdevice->last_rx = jiffies;
}
/*
* We've been placed in the UP state
*/
static int hostess_open(struct net_device *d)
{
struct z8530_dev *sv11 = dev_to_sv(d);
int err = -1;
/*
* Link layer up
*/
switch (dma) {
case 0:
err = z8530_sync_open(d, &sv11->chanA);
break;
case 1:
err = z8530_sync_dma_open(d, &sv11->chanA);
break;
case 2:
err = z8530_sync_txdma_open(d, &sv11->chanA);
break;
}
if (err)
return err;
err = hdlc_open(d);
if (err) {
switch (dma) {
case 0:
z8530_sync_close(d, &sv11->chanA);
break;
case 1:
z8530_sync_dma_close(d, &sv11->chanA);
break;
case 2:
z8530_sync_txdma_close(d, &sv11->chanA);
break;
}
return err;
}
sv11->chanA.rx_function = hostess_input;
/*
* Go go go
*/
netif_start_queue(d);
return 0;
}
static int hostess_close(struct net_device *d)
{
struct z8530_dev *sv11 = dev_to_sv(d);
/*
* Discard new frames
*/
sv11->chanA.rx_function = z8530_null_rx;
hdlc_close(d);
netif_stop_queue(d);
switch (dma) {
case 0:
z8530_sync_close(d, &sv11->chanA);
break;
case 1:
z8530_sync_dma_close(d, &sv11->chanA);
break;
case 2:
z8530_sync_txdma_close(d, &sv11->chanA);
break;
}
return 0;
}
static int hostess_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
{
/* struct z8530_dev *sv11=dev_to_sv(d);
z8530_ioctl(d,&sv11->chanA,ifr,cmd) */
return hdlc_ioctl(d, ifr, cmd);
}
/*
* Passed network frames, fire them downwind.
*/
static int hostess_queue_xmit(struct sk_buff *skb, struct net_device *d)
{
return z8530_queue_xmit(&dev_to_sv(d)->chanA, skb);
}
static int hostess_attach(struct net_device *dev, unsigned short encoding,
unsigned short parity)
{
if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
return 0;
return -EINVAL;
}
/*
* Description block for a Comtrol Hostess SV11 card
*/
static struct z8530_dev *sv11_init(int iobase, int irq)
{
struct z8530_dev *sv;
struct net_device *netdev;
/*
* Get the needed I/O space
*/
if (!request_region(iobase, 8, "Comtrol SV11")) {
printk(KERN_WARNING "hostess: I/O 0x%X already in use.\n",
iobase);
return NULL;
}
sv = kzalloc(sizeof(struct z8530_dev), GFP_KERNEL);
if (!sv)
goto err_kzalloc;
/*
* Stuff in the I/O addressing
*/
sv->active = 0;
sv->chanA.ctrlio = iobase + 1;
sv->chanA.dataio = iobase + 3;
sv->chanB.ctrlio = -1;
sv->chanB.dataio = -1;
sv->chanA.irqs = &z8530_nop;
sv->chanB.irqs = &z8530_nop;
outb(0, iobase + 4); /* DMA off */
/* We want a fast IRQ for this device. Actually we'd like an even faster
IRQ ;) - This is one driver RtLinux is made for */
if (request_irq(irq, &z8530_interrupt, IRQF_DISABLED,
"Hostess SV11", sv) < 0) {
printk(KERN_WARNING "hostess: IRQ %d already in use.\n", irq);
goto err_irq;
}
sv->irq = irq;
sv->chanA.private = sv;
sv->chanA.dev = sv;
sv->chanB.dev = sv;
if (dma) {
/*
* You can have DMA off or 1 and 3 thats the lot
* on the Comtrol.
*/
sv->chanA.txdma = 3;
sv->chanA.rxdma = 1;
outb(0x03 | 0x08, iobase + 4); /* DMA on */
if (request_dma(sv->chanA.txdma, "Hostess SV/11 (TX)"))
goto err_txdma;
if (dma == 1)
if (request_dma(sv->chanA.rxdma, "Hostess SV/11 (RX)"))
goto err_rxdma;
}
/* Kill our private IRQ line the hostess can end up chattering
until the configuration is set */
disable_irq(irq);
/*
* Begin normal initialise
*/
if (z8530_init(sv)) {
printk(KERN_ERR "Z8530 series device not found.\n");
enable_irq(irq);
goto free_dma;
}
z8530_channel_load(&sv->chanB, z8530_dead_port);
if (sv->type == Z85C30)
z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream);
else
z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream_85230);
enable_irq(irq);
/*
* Now we can take the IRQ
*/
sv->chanA.netdevice = netdev = alloc_hdlcdev(sv);
if (!netdev)
goto free_dma;
dev_to_hdlc(netdev)->attach = hostess_attach;
dev_to_hdlc(netdev)->xmit = hostess_queue_xmit;
netdev->open = hostess_open;
netdev->stop = hostess_close;
netdev->do_ioctl = hostess_ioctl;
netdev->base_addr = iobase;
netdev->irq = irq;
if (register_hdlc_device(netdev)) {
printk(KERN_ERR "hostess: unable to register HDLC device.\n");
free_netdev(netdev);
goto free_dma;
}
z8530_describe(sv, "I/O", iobase);
sv->active = 1;
return sv;
free_dma:
if (dma == 1)
free_dma(sv->chanA.rxdma);
err_rxdma:
if (dma)
free_dma(sv->chanA.txdma);
err_txdma:
free_irq(irq, sv);
err_irq:
kfree(sv);
err_kzalloc:
release_region(iobase, 8);
return NULL;
}
static void sv11_shutdown(struct z8530_dev *dev)
{
unregister_hdlc_device(dev->chanA.netdevice);
z8530_shutdown(dev);
free_irq(dev->irq, dev);
if (dma) {
if (dma == 1)
free_dma(dev->chanA.rxdma);
free_dma(dev->chanA.txdma);
}
release_region(dev->chanA.ctrlio - 1, 8);
free_netdev(dev->chanA.netdevice);
kfree(dev);
}
static int io = 0x200;
static int irq = 9;
module_param(io, int, 0);
MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
module_param(dma, int, 0);
MODULE_PARM_DESC(dma, "Set this to 1 to use DMA1/DMA3 for TX/RX");
module_param(irq, int, 0);
MODULE_PARM_DESC(irq, "The interrupt line setting for the Comtrol Hostess SV11 card");
MODULE_AUTHOR("Alan Cox");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
static struct z8530_dev *sv11_unit;
int init_module(void)
{
if ((sv11_unit = sv11_init(io, irq)) == NULL)
return -ENODEV;
return 0;
}
void cleanup_module(void)
{
if (sv11_unit)
sv11_shutdown(sv11_unit);
}
