#ifndef __MV643XX_ETH_H__
#define __MV643XX_ETH_H__
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/mv643xx.h>
#define BIT0 0x00000001
#define BIT1 0x00000002
#define BIT2 0x00000004
#define BIT3 0x00000008
#define BIT4 0x00000010
#define BIT5 0x00000020
#define BIT6 0x00000040
#define BIT7 0x00000080
#define BIT8 0x00000100
#define BIT9 0x00000200
#define BIT10 0x00000400
#define BIT11 0x00000800
#define BIT12 0x00001000
#define BIT13 0x00002000
#define BIT14 0x00004000
#define BIT15 0x00008000
#define BIT16 0x00010000
#define BIT17 0x00020000
#define BIT18 0x00040000
#define BIT19 0x00080000
#define BIT20 0x00100000
#define BIT21 0x00200000
#define BIT22 0x00400000
#define BIT23 0x00800000
#define BIT24 0x01000000
#define BIT25 0x02000000
#define BIT26 0x04000000
#define BIT27 0x08000000
#define BIT28 0x10000000
#define BIT29 0x20000000
#define BIT30 0x40000000
#define BIT31 0x80000000
/*
* The first part is the high level driver of the gigE ethernet ports.
*/
/* Checksum offload for Tx works for most packets, but
* fails if previous packet sent did not use hw csum
*/
#define MV643XX_CHECKSUM_OFFLOAD_TX
#define MV643XX_NAPI
#define MV643XX_TX_FAST_REFILL
#undef MV643XX_RX_QUEUE_FILL_ON_TASK /* Does not work, yet */
#undef MV643XX_COAL
/*
* Number of RX / TX descriptors on RX / TX rings.
* Note that allocating RX descriptors is done by allocating the RX
* ring AND a preallocated RX buffers (skb's) for each descriptor.
* The TX descriptors only allocates the TX descriptors ring,
* with no pre allocated TX buffers (skb's are allocated by higher layers.
*/
/* Default TX ring size is 1000 descriptors */
#define MV643XX_DEFAULT_TX_QUEUE_SIZE 1000
/* Default RX ring size is 400 descriptors */
#define MV643XX_DEFAULT_RX_QUEUE_SIZE 400
#define MV643XX_TX_COAL 100
#ifdef MV643XX_COAL
#define MV643XX_RX_COAL 100
#endif
/*
* The second part is the low level driver of the gigE ethernet ports.
*/
/*
* Header File for : MV-643xx network interface header
*
* DESCRIPTION:
* This header file contains macros typedefs and function declaration for
* the Marvell Gig Bit Ethernet Controller.
*
* DEPENDENCIES:
* None.
*
*/
/* MAC accepet/reject macros */
#define ACCEPT_MAC_ADDR 0
#define REJECT_MAC_ADDR 1
/* Buffer offset from buffer pointer */
#define RX_BUF_OFFSET 0x2
/* Gigabit Ethernet Unit Global Registers */
/* MIB Counters register definitions */
#define ETH_MIB_GOOD_OCTETS_RECEIVED_LOW 0x0
#define ETH_MIB_GOOD_OCTETS_RECEIVED_HIGH 0x4
#define ETH_MIB_BAD_OCTETS_RECEIVED 0x8
#define ETH_MIB_INTERNAL_MAC_TRANSMIT_ERR 0xc
#define ETH_MIB_GOOD_FRAMES_RECEIVED 0x10
#define ETH_MIB_BAD_FRAMES_RECEIVED 0x14
#define ETH_MIB_BROADCAST_FRAMES_RECEIVED 0x18
#define ETH_MIB_MULTICAST_FRAMES_RECEIVED 0x1c
#define ETH_MIB_FRAMES_64_OCTETS 0x20
#define ETH_MIB_FRAMES_65_TO_127_OCTETS 0x24
#define ETH_MIB_FRAMES_128_TO_255_OCTETS 0x28
#define ETH_MIB_FRAMES_256_TO_511_OCTETS 0x2c
#define ETH_MIB_FRAMES_512_TO_1023_OCTETS 0x30
#define ETH_MIB_FRAMES_1024_TO_MAX_OCTETS 0x34
#define ETH_MIB_GOOD_OCTETS_SENT_LOW 0x38
#define ETH_MIB_GOOD_OCTETS_SENT_HIGH 0x3c
#define ETH_MIB_GOOD_FRAMES_SENT 0x40
#define ETH_MIB_EXCESSIVE_COLLISION 0x44
#define ETH_MIB_MULTICAST_FRAMES_SENT 0x48
#define ETH_MIB_BROADCAST_FRAMES_SENT 0x4c
#define ETH_MIB_UNREC_MAC_CONTROL_RECEIVED 0x50
#define ETH_MIB_FC_SENT 0x54
#define ETH_MIB_GOOD_FC_RECEIVED 0x58
#define ETH_MIB_BAD_FC_RECEIVED 0x5c
#define ETH_MIB_UNDERSIZE_RECEIVED 0x60
#define ETH_MIB_FRAGMENTS_RECEIVED 0x64
#define ETH_MIB_OVERSIZE_RECEIVED 0x68
#define ETH_MIB_JABBER_RECEIVED 0x6c
#define ETH_MIB_MAC_RECEIVE_ERROR 0x70
#define ETH_MIB_BAD_CRC_EVENT 0x74
#define ETH_MIB_COLLISION 0x78
#define ETH_MIB_LATE_COLLISION 0x7c
/* Port serial status reg (PSR) */
#define ETH_INTERFACE_GMII_MII 0
#define ETH_INTERFACE_PCM BIT0
#define ETH_LINK_IS_DOWN 0
#define ETH_LINK_IS_UP BIT1
#define ETH_PORT_AT_HALF_DUPLEX 0
#define ETH_PORT_AT_FULL_DUPLEX BIT2
#define ETH_RX_FLOW_CTRL_DISABLED 0
#define ETH_RX_FLOW_CTRL_ENBALED BIT3
#define ETH_GMII_SPEED_100_10 0
#define ETH_GMII_SPEED_1000 BIT4
#define ETH_MII_SPEED_10 0
#define ETH_MII_SPEED_100 BIT5
#define ETH_NO_TX 0
#define ETH_TX_IN_PROGRESS BIT7
#define ETH_BYPASS_NO_ACTIVE 0
#define ETH_BYPASS_ACTIVE BIT8
#define ETH_PORT_NOT_AT_PARTITION_STATE 0
#define ETH_PORT_AT_PARTITION_STATE BIT9
#define ETH_PORT_TX_FIFO_NOT_EMPTY 0
#define ETH_PORT_TX_FIFO_EMPTY BIT10
#define ETH_DEFAULT_RX_BPDU_QUEUE_3 (BIT23 | BIT22)
#define ETH_DEFAULT_RX_BPDU_QUEUE_4 BIT24
#define ETH_DEFAULT_RX_BPDU_QUEUE_5 (BIT24 | BIT22)
#define ETH_DEFAULT_RX_BPDU_QUEUE_6 (BIT24 | BIT23)
#define ETH_DEFAULT_RX_BPDU_QUEUE_7 (BIT24 | BIT23 | BIT22)
/* SMI reg */
#define ETH_SMI_BUSY BIT28 /* 0 - Write, 1 - Read */
#define ETH_SMI_READ_VALID BIT27 /* 0 - Write, 1 - Read */
#define ETH_SMI_OPCODE_WRITE 0 /* Completion of Read operation */
#define ETH_SMI_OPCODE_READ BIT26 /* Operation is in progress */
/* SDMA command status fields macros */
/* Tx & Rx descriptors status */
#define ETH_ERROR_SUMMARY (BIT0)
/* Tx & Rx descriptors command */
#define ETH_BUFFER_OWNED_BY_DMA (BIT31)
/* Tx descriptors status */
#define ETH_LC_ERROR (0 )
#define ETH_UR_ERROR (BIT1 )
#define ETH_RL_ERROR (BIT2 )
#define ETH_LLC_SNAP_FORMAT (BIT9 )
/* Rx descriptors status */
#define ETH_CRC_ERROR (0 )
#define ETH_OVERRUN_ERROR (BIT1 )
#define ETH_MAX_FRAME_LENGTH_ERROR (BIT2 )
#define ETH_RESOURCE_ERROR ((BIT2 | BIT1))
#define ETH_VLAN_TAGGED (BIT19)
#define ETH_BPDU_FRAME (BIT20)
#define ETH_TCP_FRAME_OVER_IP_V_4 (0 )
#define ETH_UDP_FRAME_OVER_IP_V_4 (BIT21)
#define ETH_OTHER_FRAME_TYPE (BIT22)
#define ETH_LAYER_2_IS_ETH_V_2 (BIT23)
#define ETH_FRAME_TYPE_IP_V_4 (BIT24)
#define ETH_FRAME_HEADER_OK (BIT25)
#define ETH_RX_LAST_DESC (BIT26)
#define ETH_RX_FIRST_DESC (BIT27)
#define ETH_UNKNOWN_DESTINATION_ADDR (BIT28)
#define ETH_RX_ENABLE_INTERRUPT (BIT29)
#define ETH_LAYER_4_CHECKSUM_OK (BIT30)
/* Rx descriptors byte count */
#define ETH_FRAME_FRAGMENTED (BIT2)
/* Tx descriptors command */
#define ETH_LAYER_4_CHECKSUM_FIRST_DESC (BIT10)
#define ETH_FRAME_SET_TO_VLAN (BIT15)
#define ETH_TCP_FRAME (0 )
#define ETH_UDP_FRAME (BIT16)
#define ETH_GEN_TCP_UDP_CHECKSUM (BIT17)
#define ETH_GEN_IP_V_4_CHECKSUM (BIT18)
#define ETH_ZERO_PADDING (BIT19)
#define ETH_TX_LAST_DESC (BIT20)
#define ETH_TX_FIRST_DESC (BIT21)
#define ETH_GEN_CRC (BIT22)
#define ETH_TX_ENABLE_INTERRUPT (BIT23)
#define ETH_AUTO_MODE (BIT30)
#define ETH_TX_IHL_SHIFT 11
/* typedefs */
typedef enum _eth_func_ret_status {
ETH_OK, /* Returned as expected. */
ETH_ERROR, /* Fundamental error. */
ETH_RETRY, /* Could not process request. Try later.*/
ETH_END_OF_JOB, /* Ring has nothing to process. */
ETH_QUEUE_FULL, /* Ring resource error. */
ETH_QUEUE_LAST_RESOURCE /* Ring resources about to exhaust. */
} ETH_FUNC_RET_STATUS;
typedef enum _eth_target {
ETH_TARGET_DRAM,
ETH_TARGET_DEVICE,
ETH_TARGET_CBS,
ETH_TARGET_PCI0,
ETH_TARGET_PCI1
} ETH_TARGET;
/* These are for big-endian machines. Little endian needs different
* definitions.
*/
#if defined(__BIG_ENDIAN)
struct eth_rx_desc {
u16 byte_cnt; /* Descriptor buffer byte count */
u16 buf_size; /* Buffer size */
u32 cmd_sts; /* Descriptor command status */
u32 next_desc_ptr; /* Next descriptor pointer */
u32 buf_ptr; /* Descriptor buffer pointer */
};
struct eth_tx_desc {
u16 byte_cnt; /* buffer byte count */
u16 l4i_chk; /* CPU provided TCP checksum */
u32 cmd_sts; /* Command/status field */
u32 next_desc_ptr; /* Pointer to next descriptor */
u32 buf_ptr; /* pointer to buffer for this descriptor*/
};
#elif defined(__LITTLE_ENDIAN)
struct eth_rx_desc {
u32 cmd_sts; /* Descriptor command status */
u16 buf_size; /* Buffer size */
u16 byte_cnt; /* Descriptor buffer byte count */
u32 buf_ptr; /* Descriptor buffer pointer */
u32 next_desc_ptr; /* Next descriptor pointer */
};
struct eth_tx_desc {
u32 cmd_sts; /* Command/status field */
u16 l4i_chk; /* CPU provided TCP checksum */
u16 byte_cnt; /* buffer byte count */
u32 buf_ptr; /* pointer to buffer for this descriptor*/
u32 next_desc_ptr; /* Pointer to next descriptor */
};
#else
#error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined
#endif
/* Unified struct for Rx and Tx operations. The user is not required to */
/* be familier with neither Tx nor Rx descriptors. */
struct pkt_info {
unsigned short byte_cnt; /* Descriptor buffer byte count */
unsigned short l4i_chk; /* Tx CPU provided TCP Checksum */
unsigned int cmd_sts; /* Descriptor command status */
dma_addr_t buf_ptr; /* Descriptor buffer pointer */
struct sk_buff *return_info; /* User resource return information */
};
/* Ethernet port specific infomation */
struct mv643xx_mib_counters {
u64 good_octets_received;
u32 bad_octets_received;
u32 internal_mac_transmit_err;
u32 good_frames_received;
u32 bad_frames_received;
u32 broadcast_frames_received;
u32 multicast_frames_received;
u32 frames_64_octets;
u32 frames_65_to_127_octets;
u32 frames_128_to_255_octets;
u32 frames_256_to_511_octets;
u32 frames_512_to_1023_octets;
u32 frames_1024_to_max_octets;
u64 good_octets_sent;
u32 good_frames_sent;
u32 excessive_collision;
u32 multicast_frames_sent;
u32 broadcast_frames_sent;
u32 unrec_mac_control_received;
u32 fc_sent;
u32 good_fc_received;
u32 bad_fc_received;
u32 undersize_received;
u32 fragments_received;
u32 oversize_received;
u32 jabber_received;
u32 mac_receive_error;
u32 bad_crc_event;
u32 collision;
u32 late_collision;
};
struct mv643xx_private {
int port_num; /* User Ethernet port number */
u8 port_mac_addr[6]; /* User defined port MAC address.*/
u32 port_config; /* User port configuration value*/
u32 port_config_extend; /* User port config extend value*/
u32 port_sdma_config; /* User port SDMA config value */
u32 port_serial_control; /* User port serial control value */
u32 port_tx_queue_command; /* Port active Tx queues summary*/
u32 port_rx_queue_command; /* Port active Rx queues summary*/
u32 rx_sram_addr; /* Base address of rx sram area */
u32 rx_sram_size; /* Size of rx sram area */
u32 tx_sram_addr; /* Base address of tx sram area */
u32 tx_sram_size; /* Size of tx sram area */
int rx_resource_err; /* Rx ring resource error flag */
int tx_resource_err; /* Tx ring resource error flag */
/* Tx/Rx rings managment indexes fields. For driver use */
/* Next available and first returning Rx resource */
int rx_curr_desc_q, rx_used_desc_q;
/* Next available and first returning Tx resource */
int tx_curr_desc_q, tx_used_desc_q;
#ifdef MV643XX_CHECKSUM_OFFLOAD_TX
int tx_first_desc_q;
u32 tx_first_command;
#endif
#ifdef MV643XX_TX_FAST_REFILL
u32 tx_clean_threshold;
#endif
struct eth_rx_desc *p_rx_desc_area;
dma_addr_t rx_desc_dma;
unsigned int rx_desc_area_size;
struct sk_buff **rx_skb;
struct eth_tx_desc *p_tx_desc_area;
dma_addr_t tx_desc_dma;
unsigned int tx_desc_area_size;
struct sk_buff **tx_skb;
struct work_struct tx_timeout_task;
/*
* Former struct mv643xx_eth_priv members start here
*/
struct net_device_stats stats;
struct mv643xx_mib_counters mib_counters;
spinlock_t lock;
/* Size of Tx Ring per queue */
unsigned int tx_ring_size;
/* Ammont of SKBs outstanding on Tx queue */
unsigned int tx_ring_skbs;
/* Size of Rx Ring per queue */
unsigned int rx_ring_size;
/* Ammount of SKBs allocated to Rx Ring per queue */
unsigned int rx_ring_skbs;
/*
* rx_task used to fill RX ring out of bottom half context
*/
struct work_struct rx_task;
/*
* Used in case RX Ring is empty, which can be caused when
* system does not have resources (skb's)
*/
struct timer_list timeout;
long rx_task_busy __attribute__ ((aligned(SMP_CACHE_BYTES)));
unsigned rx_timer_flag;
u32 rx_int_coal;
u32 tx_int_coal;
};
/* ethernet.h API list */
/* Port operation control routines */
static void eth_port_init(struct mv643xx_private *mp);
static void eth_port_reset(unsigned int eth_port_num);
static void eth_port_start(struct mv643xx_private *mp);
/* Port MAC address routines */
static void eth_port_uc_addr_set(unsigned int eth_port_num,
unsigned char *p_addr);
/* PHY and MIB routines */
static void ethernet_phy_reset(unsigned int eth_port_num);
static void eth_port_write_smi_reg(unsigned int eth_port_num,
unsigned int phy_reg, unsigned int value);
static void eth_port_read_smi_reg(unsigned int eth_port_num,
unsigned int phy_reg, unsigned int *value);
static void eth_clear_mib_counters(unsigned int eth_port_num);
/* Port data flow control routines */
static ETH_FUNC_RET_STATUS eth_port_send(struct mv643xx_private *mp,
struct pkt_info *p_pkt_info);
static ETH_FUNC_RET_STATUS eth_tx_return_desc(struct mv643xx_private *mp,
struct pkt_info *p_pkt_info);
static ETH_FUNC_RET_STATUS eth_port_receive(struct mv643xx_private *mp,
struct pkt_info *p_pkt_info);
static ETH_FUNC_RET_STATUS eth_rx_return_buff(struct mv643xx_private *mp,
struct pkt_info *p_pkt_info);
#endif /* __MV643XX_ETH_H__ */
