#
# Network device configuration
#
config HAVE_NET_MACB
bool
menuconfig NETDEVICES
default y if UML
depends on NET
bool "Network device support"
---help---
You can say N here if you don't intend to connect your Linux box to
any other computer at all.
You'll have to say Y if your computer contains a network card that
you want to use under Linux. If you are going to run SLIP or PPP over
telephone line or null modem cable you need say Y here. Connecting
two machines with parallel ports using PLIP needs this, as well as
AX.25/KISS for sending Internet traffic over amateur radio links.
See also "The Linux Network Administrator's Guide" by Olaf Kirch and
Terry Dawson. Available at <http://www.tldp.org/guides.html>.
If unsure, say Y.
# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
---help---
This is an intermediate driver that allows sharing of
resources.
To compile this driver as a module, choose M here: the module
will be called ifb. If you want to use more than one ifb
device at a time, you need to compile this driver as a module.
Instead of 'ifb', the devices will then be called 'ifb0',
'ifb1' etc.
Look at the iproute2 documentation directory for usage etc
config DUMMY
tristate "Dummy net driver support"
---help---
This is essentially a bit-bucket device (i.e. traffic you send to
this device is consigned into oblivion) with a configurable IP
address. It is most commonly used in order to make your currently
inactive SLIP address seem like a real address for local programs.
If you use SLIP or PPP, you might want to say Y here. Since this
thing often comes in handy, the default is Y. It won't enlarge your
kernel either. What a deal. Read about it in the Network
Administrator's Guide, available from
<http://www.tldp.org/docs.html#guide>.
To compile this driver as a module, choose M here: the module
will be called dummy. If you want to use more than one dummy
device at a time, you need to compile this driver as a module.
Instead of 'dummy', the devices will then be called 'dummy0',
'dummy1' etc.
config BONDING
tristate "Bonding driver support"
depends on INET
depends on IPV6 || IPV6=n
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
Channels together. This is called 'Etherchannel' by Cisco,
'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
The driver supports multiple bonding modes to allow for both high
performance and high availability operation.
Refer to <file:Documentation/networking/bonding.txt> for more
information.
To compile this driver as a module, choose M here: the module
will be called bonding.
config MACVLAN
tristate "MAC-VLAN support (EXPERIMENTAL)"
depends on EXPERIMENTAL
---help---
This allows one to create virtual interfaces that map packets to
or from specific MAC addresses to a particular interface.
Macvlan devices can be added using the "ip" command from the
iproute2 package starting with the iproute2-2.6.23 release:
"ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
To compile this driver as a module, choose M here: the module
will be called macvlan.
config MACVTAP
tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
depends on MACVLAN
help
This adds a specialized tap character device driver that is based
on the MAC-VLAN network interface, called macvtap. A macvtap device
can be added in the same way as a macvlan device, using 'type
macvlan', and then be accessed through the tap user space interface.
To compile this driver as a module, choose M here: the module
will be called macvtap.
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
If you have two serial connections to some other computer (this
usually requires two modems and two telephone lines) and you use
SLIP (the protocol for sending Internet traffic over telephone
lines) or PPP (a better SLIP) on them, you can make them behave like
one double speed connection using this driver. Naturally, this has
to be supported at the other end as well, either with a similar EQL
Linux driver or with a Livingston Portmaster 2e.
Say Y if you want this and read
<file:Documentation/networking/eql.txt>. You may also want to read
section 6.2 of the NET-3-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here: the module
will be called eql. If unsure, say N.
config TUN
tristate "Universal TUN/TAP device driver support"
select CRC32
---help---
TUN/TAP provides packet reception and transmission for user space
programs. It can be viewed as a simple Point-to-Point or Ethernet
device, which instead of receiving packets from a physical media,
receives them from user space program and instead of sending packets
via physical media writes them to the user space program.
When a program opens /dev/net/tun, driver creates and registers
corresponding net device tunX or tapX. After a program closed above
devices, driver will automatically delete tunXX or tapXX device and
all routes corresponding to it.
Please read <file:Documentation/networking/tuntap.txt> for more
information.
To compile this driver as a module, choose M here: the module
will be called tun.
If you don't know what to use this for, you don't need it.
config VETH
tristate "Virtual ethernet pair device"
---help---
This device is a local ethernet tunnel. Devices are created in pairs.
When one end receives the packet it appears on its pair and vice
versa.
config NET_SB1000
tristate "General Instruments Surfboard 1000"
depends on PNP
---help---
This is a driver for the General Instrument (also known as
NextLevel) SURFboard 1000 internal
cable modem. This is an ISA card which is used by a number of cable
TV companies to provide cable modem access. It's a one-way
downstream-only cable modem, meaning that your upstream net link is
provided by your regular phone modem.
At present this driver only compiles as a module, so say M here if
you have this card. The module will be called sb1000. Then read
<file:Documentation/networking/README.sb1000> for information on how
to use this module, as it needs special ppp scripts for establishing
a connection. Further documentation and the necessary scripts can be
found at:
<http://www.jacksonville.net/~fventuri/>
<http://home.adelphia.net/~siglercm/sb1000.html>
<http://linuxpower.cx/~cable/>
If you don't have this card, of course say N.
source "drivers/net/arcnet/Kconfig"
config MII
tristate "Generic Media Independent Interface device support"
help
Most ethernet controllers have MII transceiver either as an external
or internal device. It is safe to say Y or M here even if your
ethernet card lacks MII.
source "drivers/net/phy/Kconfig"
#
# Ethernet
#
source "drivers/net/ethernet/Kconfig"
menuconfig NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
depends on !UML
---help---
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
type of Local Area Network (LAN) in universities and companies.
Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
coaxial cable, linking computers in a chain), 10BASE-T or twisted
pair (10 Mbps over twisted pair cable, linking computers to central
hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
[the 100BASE varieties are also known as Fast Ethernet], and Gigabit
Ethernet (1 Gbps over optical fiber or short copper links).
If your Linux machine will be connected to an Ethernet and you have
an Ethernet network interface card (NIC) installed in your computer,
say Y here and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>. You will then also have
to say Y to the driver for your particular NIC.
Note that the answer to this question won't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Ethernet network cards. If unsure, say N.
if NET_ETHERNET
config MACB
tristate "Atmel MACB support"
depends on HAVE_NET_MACB
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
parts. Say Y to include support for the MACB chip.
To compile this driver as a module, choose M here: the module
will be called macb.
source "drivers/net/arm/Kconfig"
config KORINA
tristate "Korina (IDT RC32434) Ethernet support"
depends on NET_ETHERNET && MIKROTIK_RB532
help
If you have a Mikrotik RouterBoard 500 or IDT RC32434
based system say Y. Otherwise say N.
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
depends on PCI && SGI_IP27
select CRC32
select MII
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
depends on MIPS_SIM
help
The MIPSNET device is a simple Ethernet network device which is
emulated by the MIPS Simulator.
If you are not using a MIPSsim or are unsure, say N.
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on SGI_IP32=y
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
(CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7757)
select CRC32
select MII
select MDIO_BITBANG
select PHYLIB
help
Renesas SuperH Ethernet device driver.
This driver supporting CPUs are:
- SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757.
config BFIN_MAC
tristate "Blackfin on-chip MAC support"
depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
select CRC32
select MII
select PHYLIB
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
help
This is the driver for Blackfin on-chip mac device. Say Y if you want it
compiled into the kernel. This driver is also available as a module
( = code which can be inserted in and removed from the running kernel
whenever you want). The module will be called bfin_mac.
config BFIN_MAC_USE_L1
bool "Use L1 memory for rx/tx packets"
depends on BFIN_MAC && (BF527 || BF537)
default y
help
To get maximum network performance, you should use L1 memory as rx/tx buffers.
Say N here if you want to reserve L1 memory for other uses.
config BFIN_TX_DESC_NUM
int "Number of transmit buffer packets"
depends on BFIN_MAC
range 6 10 if BFIN_MAC_USE_L1
range 10 100
default "10"
help
Set the number of buffer packets used in driver.
config BFIN_RX_DESC_NUM
int "Number of receive buffer packets"
depends on BFIN_MAC
range 20 100 if BFIN_MAC_USE_L1
range 20 800
default "20"
help
Set the number of buffer packets used in driver.
config BFIN_MAC_USE_HWSTAMP
bool "Use IEEE 1588 hwstamp"
depends on BFIN_MAC && BF518
default y
help
To support the IEEE 1588 Precision Time Protocol (PTP), select y here
config PXA168_ETH
tristate "Marvell pxa168 ethernet support"
depends on CPU_PXA168
select PHYLIB
help
This driver supports the pxa168 Ethernet ports.
To compile this driver as a module, choose M here. The module
will be called pxa168_eth.
config NET_NETX
tristate "NetX Ethernet support"
select MII
depends on ARCH_NETX
help
This is support for the Hilscher netX builtin Ethernet ports
To compile this driver as a module, choose M here. The module
will be called netx-eth.
config TI_DAVINCI_EMAC
tristate "TI DaVinci EMAC Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select TI_DAVINCI_MDIO
select TI_DAVINCI_CPDMA
select PHYLIB
help
This driver supports TI's DaVinci Ethernet .
To compile this driver as a module, choose M here: the module
will be called davinci_emac_driver. This is recommended.
config TI_DAVINCI_MDIO
tristate "TI DaVinci MDIO Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select PHYLIB
help
This driver supports TI's DaVinci MDIO module.
To compile this driver as a module, choose M here: the module
will be called davinci_mdio. This is recommended.
config TI_DAVINCI_CPDMA
tristate "TI DaVinci CPDMA Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
help
This driver supports TI's DaVinci CPDMA dma engine.
To compile this driver as a module, choose M here: the module
will be called davinci_cpdma. This is recommended.
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
select CRC32
select MII
---help---
Support for DM9000 chipset.
To compile this driver as a module, choose M here. The module
will be called dm9000.
config DM9000_DEBUGLEVEL
int "DM9000 maximum debug level"
depends on DM9000
default 4
help
The maximum level of debugging code compiled into the DM9000
driver.
config DM9000_FORCE_SIMPLE_PHY_POLL
bool "Force simple NSR based PHY polling"
depends on DM9000
---help---
This configuration forces the DM9000 to use the NSR's LinkStatus
bit to determine if the link is up or down instead of the more
costly MII PHY reads. Note, this will not work if the chip is
operating with an external PHY.
config ENC28J60
tristate "ENC28J60 support"
depends on EXPERIMENTAL && SPI && NET_ETHERNET
select CRC32
---help---
Support for the Microchip EN28J60 ethernet chip.
To compile this driver as a module, choose M here. The module will be
called enc28j60.
config ENC28J60_WRITEVERIFY
bool "Enable write verify"
depends on ENC28J60
---help---
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
config ETHOC
tristate "OpenCores 10/100 Mbps Ethernet MAC support"
depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
select BITREVERSE
help
Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
config GRETH
tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
depends on SPARC
select PHYLIB
select CRC32
help
Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.
config DNET
tristate "Dave ethernet support (DNET)"
depends on NET_ETHERNET && HAS_IOMEM
select PHYLIB
help
The Dave ethernet interface (DNET) is found on Qong Board FPGA.
Say Y to include support for the DNET chip.
To compile this driver as a module, choose M here: the module
will be called dnet.
source "drivers/net/tulip/Kconfig"
config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called at1700.
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
depends on ISA || EISA || PCI
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called hp100.
config NET_ISA
bool "Other ISA cards"
depends on ISA
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
Make sure you know the name of your card. Read the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>.
If unsure, say Y.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the remaining ISA network card questions. If you say Y, you will be
asked for your specific card in the following questions.
config EWRK3
tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
depends on NET_ISA
select CRC32
---help---
This driver supports the DE203, DE204 and DE205 network (Ethernet)
cards. If this is for you, say Y and read
<file:Documentation/networking/ewrk3.txt> in the kernel source as
well as the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called ewrk3.
config ETH16I
tristate "ICL EtherTeam 16i/32 support"
depends on NET_ISA
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called eth16i.
config SEEQ8005
tristate "SEEQ8005 support (EXPERIMENTAL)"
depends on NET_ISA && EXPERIMENTAL
help
This is a driver for the SEEQ 8005 network (Ethernet) card. If this
is for you, read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called seeq8005.
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
depends on ISA || EISA || PCI
help
This is another class of network cards which attach directly to the
bus. If you have one of those, say Y and read the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about this class of network cards. If you say Y, you
will be asked for your specific card in the following questions. If
you are unsure, say Y.
config ADAPTEC_STARFIRE
tristate "Adaptec Starfire/DuraLAN support"
depends on NET_PCI && PCI
select CRC32
select MII
help
Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
adapter. The DuraLAN chip is used on the 64 bit PCI boards from
Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
driver.
To compile this driver as a module, choose M here: the module
will be called starfire. This is recommended.
config KSZ884X_PCI
tristate "Micrel KSZ8841/2 PCI"
depends on NET_PCI && PCI
select MII
select CRC32
help
This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
To compile this driver as a module, choose M here. The module
will be called ksz884x.
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
help
If you have a network (Ethernet) controller of this type, say Y and
read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called forcedeth.
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
select PHYLIB
config FEALNX
tristate "Myson MTD-8xx PCI Ethernet support"
depends on NET_PCI && PCI
select CRC32
select MII
help
Say Y here to support the Myson MTD-800 family of PCI-based Ethernet
cards. <http://www.myson.com.tw/>
config 8139CP
tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
depends on NET_PCI && PCI && EXPERIMENTAL
select CRC32
select MII
help
This is a driver for the Fast Ethernet PCI network cards based on
the RTL8139C+ chips. If you have one of those, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here: the module
will be called 8139cp. This is recommended.
config 8139TOO
tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
---help---
This is a driver for the Fast Ethernet PCI network cards based on
the RTL 8129/8130/8139 chips. If you have one of those, say Y and
read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here: the module
will be called 8139too. This is recommended.
config 8139TOO_PIO
bool "Use PIO instead of MMIO"
default y
depends on 8139TOO
help
This instructs the driver to use programmed I/O ports (PIO) instead
of PCI shared memory (MMIO). This can possibly solve some problems
in case your mainboard has memory consistency issues. If unsure,
say N.
config 8139TOO_TUNE_TWISTER
bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
depends on 8139TOO
help
This implements a function which might come in handy in case you
are using low quality on long cabling. It is required for RealTek
RTL-8139 revision K boards, and totally unused otherwise. It tries
to match the transceiver to the cable characteristics. This is
experimental since hardly documented by the manufacturer.
If unsure, say Y.
config 8139TOO_8129
bool "Support for older RTL-8129/8130 boards"
depends on 8139TOO
help
This enables support for the older and uncommon RTL-8129 and
RTL-8130 chips, which support MII via an external transceiver,
instead of an internal one. Disabling this option will save some
memory by making the code size smaller. If unsure, say Y.
config 8139_OLD_RX_RESET
bool "Use older RX-reset method"
depends on 8139TOO
help
The 8139too driver was recently updated to contain a more rapid
reset sequence, in the face of severe receive errors. This "new"
RX-reset method should be adequate for all boards. But if you
experience problems, you can enable this option to restore the
old RX-reset behavior. If unsure, say N.
config R6040
tristate "RDC R6040 Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
select PHYLIB
help
This is a driver for the R6040 Fast Ethernet MACs found in the
the RDC R-321x System-on-chips.
To compile this driver as a module, choose M here: the module
will be called r6040. This is recommended.
config SIS900
tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
---help---
This is a driver for the Fast Ethernet PCI network cards based on
the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
SiS 630 and SiS 540 chipsets.
This driver also supports AMD 79C901 HomePNA so that you can use
your phone line as a network cable.
To compile this driver as a module, choose M here: the module
will be called sis900. This is recommended.
config SUNDANCE
tristate "Sundance Alta support"
depends on NET_PCI && PCI
select CRC32
select MII
help
This driver is for the Sundance "Alta" chip.
More specific information and updates are available from
<http://www.scyld.com/network/sundance.html>.
config SUNDANCE_MMIO
bool "Use MMIO instead of PIO"
depends on SUNDANCE
help
Enable memory-mapped I/O for interaction with Sundance NIC registers.
Do NOT enable this by default, PIO (enabled when MMIO is disabled)
is known to solve bugs on certain chips.
If unsure, say N.
config TLAN
tristate "TI ThunderLAN support"
depends on NET_PCI && (PCI || EISA)
---help---
If you have a PCI Ethernet network card based on the ThunderLAN chip
which is supported by this driver, say Y and read the
Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Devices currently supported by this driver are Compaq Netelligent,
Compaq NetFlex and Olicom cards. Please read the file
<file:Documentation/networking/tlan.txt> for more details.
To compile this driver as a module, choose M here. The module
will be called tlan.
Please email feedback to <torben.mathiasen@compaq.com>.
config KS8842
tristate "Micrel KSZ8841/42 with generic bus interface"
depends on HAS_IOMEM && DMA_ENGINE
help
This platform driver is for KSZ8841(1-port) / KS8842(2-port)
ethernet switch chip (managed, VLAN, QoS) from Micrel or
Timberdale(FPGA).
config KS8851
tristate "Micrel KS8851 SPI"
depends on SPI
select MII
select CRC32
help
SPI driver for Micrel KS8851 SPI attached network chip.
config KS8851_MLL
tristate "Micrel KS8851 MLL"
depends on HAS_IOMEM
select MII
help
This platform driver is for Micrel KS8851 Address/data bus
multiplexed network chip.
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
select CRC32
select MII
help
If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
Ethernet functions can also be found integrated on South Bridges
(e.g. VT8235).
To compile this driver as a module, choose M here. The module
will be called via-rhine.
config VIA_RHINE_MMIO
bool "Use MMIO instead of PIO"
depends on VIA_RHINE
help
This instructs the driver to use PCI shared memory (MMIO) instead of
programmed I/O ports (PIO). Enabling this gives an improvement in
processing time in parts of the driver.
If unsure, say Y.
config SC92031
tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
depends on NET_PCI && PCI && EXPERIMENTAL
select CRC32
---help---
This is a driver for the Fast Ethernet PCI network cards based on
the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
have one of these, say Y here.
To compile this driver as a module, choose M here: the module
will be called sc92031. This is recommended.
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
config NET_POCKET
bool "Pocket and portable adapters"
depends on PARPORT
---help---
Cute little network (Ethernet) devices which attach to the parallel
port ("pocket adapters"), commonly used with laptops. If you have
one of those, say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
If you want to plug a network (or some other) card into the PCMCIA
(or PC-card) slot of your laptop instead (PCMCIA is the standard for
credit card size extension cards used by all modern laptops), you
need the pcmcia-cs package (location contained in the file
<file:Documentation/Changes>) and you can say N here.
Laptop users should read the Linux Laptop home page at
<http://www.linux-on-laptops.com/> or
Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about this class of network devices. If you say Y, you
will be asked for your specific device in the following questions.
config ATP
tristate "AT-LAN-TEC/RealTek pocket adapter support"
depends on NET_POCKET && PARPORT && X86
select CRC32
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>, if you
want to use this. If you intend to use this driver, you should have
said N to the "Parallel printer support", because the two drivers
don't like each other.
To compile this driver as a module, choose M here: the module
will be called atp.
config DE600
tristate "D-Link DE600 pocket adapter support"
depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, if you want to use
this. It is possible to have several devices share a single parallel
port and it is safe to compile the corresponding drivers into the
kernel.
To compile this driver as a module, choose M here: the module
will be called de600.
config DE620
tristate "D-Link DE620 pocket adapter support"
depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, if you want to use
this. It is possible to have several devices share a single parallel
port and it is safe to compile the corresponding drivers into the
kernel.
To compile this driver as a module, choose M here: the module
will be called de620.
config SGISEEQ
tristate "SGI Seeq ethernet controller support"
depends on SGI_HAS_SEEQ
help
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC
default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
select PHYLIB
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
config FEC_MPC52xx
tristate "MPC52xx FEC driver"
depends on PPC_MPC52xx && PPC_BESTCOMM
select CRC32
select PHYLIB
select PPC_BESTCOMM_FEC
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "MPC52xx FEC MDIO bus driver"
depends on FEC_MPC52xx
default y
---help---
The MPC5200's FEC can connect to the Ethernet either with
an external MII PHY chip or 10 Mbps 7-wire interface
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
If compiled as module, it will be called fec_mpc52xx_phy.
config ATL2
tristate "Atheros L2 Fast Ethernet support"
depends on PCI
select CRC32
select MII
help
This driver supports the Atheros L2 fast ethernet adapter.
To compile this driver as a module, choose M here. The module
will be called atl2.
config XILINX_EMACLITE
tristate "Xilinx 10/100 Ethernet Lite support"
depends on PPC32 || MICROBLAZE
select PHYLIB
help
This driver supports the 10/100 Ethernet Lite from Xilinx.
config FTMAC100
tristate "Faraday FTMAC100 10/100 Ethernet support"
depends on ARM
select MII
help
This driver supports the FTMAC100 10/100 Ethernet controller
from Faraday. It is used on Faraday A320, Andes AG101 and some
other ARM/NDS32 SoC's.
config LANTIQ_ETOP
tristate "Lantiq SoC ETOP driver"
depends on SOC_TYPE_XWAY
help
Support for the MII0 inside the Lantiq SoC
source "drivers/net/fs_enet/Kconfig"
source "drivers/net/octeon/Kconfig"
endif # NET_ETHERNET
#
# Gigabit Ethernet
#
menuconfig NETDEV_1000
bool "Ethernet (1000 Mbit)"
depends on !UML
default y
---help---
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
type of Local Area Network (LAN) in universities and companies.
Say Y here to get to see options for Gigabit Ethernet drivers.
This option alone does not add any kernel code.
Note that drivers supporting both 100 and 1000 MBit may be listed
under "Ethernet (10 or 100MBit)" instead.
If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_1000
config DL2K
tristate "DL2000/TC902x-based Gigabit Ethernet support"
depends on PCI
select CRC32
help
This driver supports DL2000/TC902x-based Gigabit ethernet cards,
which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
To compile this driver as a module, choose M here: the
module will be called dl2k.
config IP1000
tristate "IP1000 Gigabit Ethernet support"
depends on PCI && EXPERIMENTAL
select MII
---help---
This driver supports IP1000 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called ipg. This is recommended.
source "drivers/net/ixp2000/Kconfig"
config HAMACHI
tristate "Packet Engines Hamachi GNIC-II support"
depends on PCI
select MII
help
If you have a Gigabit Ethernet card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module will be
called hamachi.
config YELLOWFIN
tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
select CRC32
---help---
Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
used by the Beowulf Linux cluster project. See
<http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
information about this driver in particular and Beowulf in general.
To compile this driver as a module, choose M here: the module
will be called yellowfin. This is recommended.
config R8169
tristate "Realtek 8169 gigabit ethernet support"
depends on PCI
select FW_LOADER
select CRC32
select MII
---help---
Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
To compile this driver as a module, choose M here: the module
will be called r8169. This is recommended.
config SIS190
tristate "SiS190/SiS191 gigabit ethernet support"
depends on PCI
select CRC32
select MII
---help---
Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
appear in lan on motherboard designs which are based on SiS 965
and SiS 966 south bridge.
To compile this driver as a module, choose M here: the module
will be called sis190. This is recommended.
config SKGE
tristate "Marvell Yukon Gigabit Ethernet support"
depends on PCI
select CRC32
---help---
This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
and related Gigabit Ethernet adapters. It is a new smaller driver
with better performance and more complete ethtool support.
It does not support the link failover and network management
features that "portable" vendor supplied sk98lin driver does.
This driver supports adapters based on the original Yukon chipset:
Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
It does not support the newer Yukon2 chipset: a separate driver,
sky2, is provided for these adapters.
To compile this driver as a module, choose M here: the module
will be called skge. This is recommended.
config SKGE_DEBUG
bool "Debugging interface"
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
config SKGE_GENESIS
bool "Support for older SysKonnect Genesis boards"
depends on SKGE
help
This enables support for the older and uncommon SysKonnect Genesis
chips, which support MII via an external transceiver, instead of
an internal one. Disabling this option will save some memory
by making code smaller. If unsure say Y.
config SKY2
tristate "Marvell Yukon 2 support"
depends on PCI
select CRC32
---help---
This driver supports Gigabit Ethernet adapters based on the
Marvell Yukon 2 chipset:
Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
There is companion driver for the older Marvell Yukon and
SysKonnect Genesis based adapters: skge.
To compile this driver as a module, choose M here: the module
will be called sky2. This is recommended.
config SKY2_DEBUG
bool "Debugging interface"
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on PCI
select CRC32
select CRC_CCITT
select MII
help
If you have a VIA "Velocity" based network card say Y here.
To compile this driver as a module, choose M here. The module
will be called via-velocity.
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
select FW_LOADER
help
This driver supports the Gigabit Ethernet chips present on the
Cell Processor-Based Blades from IBM.
config TSI108_ETH
tristate "Tundra TSI108 gigabit Ethernet support"
depends on TSI108_BRIDGE
help
This driver supports Tundra TSI108 gigabit Ethernet ports.
To compile this driver as a module, choose M here: the module
will be called tsi108_eth.
config GELIC_NET
tristate "PS3 Gigabit Ethernet driver"
depends on PPC_PS3
select PS3_SYS_MANAGER
help
This driver supports the network device on the PS3 game
console. This driver has built-in support for Ethernet.
To compile this driver as a module, choose M here: the
module will be called ps3_gelic.
config GELIC_WIRELESS
bool "PS3 Wireless support"
depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
This option adds the support for the wireless feature of PS3.
If you have the wireless-less model of PS3 or have no plan to
use wireless feature, disabling this option saves memory. As
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
config FSL_PQ_MDIO
tristate "Freescale PQ MDIO"
depends on FSL_SOC
select PHYLIB
help
This driver supports the MDIO bus used by the gianfar and UCC drivers.
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
select FSL_PQ_MDIO
select PHYLIB
select CRC32
help
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
and MPC86xx family of chips, and the FEC on the 8540.
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
select FSL_PQ_MDIO
select PHYLIB
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
select INET_LRO
select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
Marvell Discovery PPC/MIPS chipset family (MV643XX) and
in the Marvell Orion ARM SoC family.
Some boards that use the Discovery chipset are the Momenco
Ocelot C and Jaguar ATX and Pegasos II.
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on PPC || MICROBLAZE
select PHYLIB
help
This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
core used in Xilinx Spartan and Virtex FPGAs
config ATL1
tristate "Atheros/Attansic L1 Gigabit Ethernet support"
depends on PCI
select CRC32
select MII
help
This driver supports the Atheros/Attansic L1 gigabit ethernet
adapter.
To compile this driver as a module, choose M here. The module
will be called atl1.
config ATL1E
tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
select CRC32
select MII
help
This driver supports the Atheros L1E gigabit ethernet adapter.
To compile this driver as a module, choose M here. The module
will be called atl1e.
config ATL1C
tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
select CRC32
select MII
help
This driver supports the Atheros L1C gigabit ethernet adapter.
To compile this driver as a module, choose M here. The module
will be called atl1c.
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
select CRC32
select MII
---help---
This driver supports the PCI-Express gigabit ethernet adapters
based on JMicron JMC250 chipset.
To compile this driver as a module, choose M here. The module
will be called jme.
config S6GMAC
tristate "S6105 GMAC ethernet support"
depends on XTENSA_VARIANT_S6000
select PHYLIB
help
This driver supports the on chip ethernet device on the
S6105 xtensa processor.
To compile this driver as a module, choose M here. The module
will be called s6gmac.
config PCH_GBE
tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GbE"
depends on PCI
select MII
---help---
This is a gigabit ethernet driver for EG20T PCH.
EG20T PCH is the platform controller hub that is used in Intel's
general embedded platform.
EG20T PCH has Gigabit Ethernet interface.
Using this interface, it is able to access system devices connected
to Gigabit Ethernet.
This driver enables Gigabit Ethernet function.
This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
Output Hub), ML7223.
ML7223 IOH is for MP(Media Phone) use.
ML7223 is companion chip for Intel Atom E6xx series.
ML7223 is completely compatible for Intel EG20T PCH.
config FTGMAC100
tristate "Faraday FTGMAC100 Gigabit Ethernet support"
depends on ARM
select PHYLIB
help
This driver supports the FTGMAC100 Gigabit Ethernet controller
from Faraday. It is used on Faraday A369, Andes AG102 and some
other ARM/NDS32 SoC's.
endif # NETDEV_1000
#
# 10 Gigabit Ethernet
#
menuconfig NETDEV_10000
bool "Ethernet (10000 Mbit)"
depends on !UML
default y
---help---
Say Y here to get to see options for 10 Gigabit Ethernet drivers.
This option alone does not add any kernel code.
If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_10000
config MDIO
tristate
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
source "drivers/net/wireless/Kconfig"
source "drivers/net/wimax/Kconfig"
source "drivers/net/usb/Kconfig"
source "drivers/net/pcmcia/Kconfig"
source "drivers/net/wan/Kconfig"
source "drivers/atm/Kconfig"
source "drivers/ieee802154/Kconfig"
source "drivers/s390/net/Kconfig"
source "drivers/net/caif/Kconfig"
config TILE_NET
tristate "Tilera GBE/XGBE network driver support"
depends on TILE
default y
select CRC32
help
This is a standard Linux network device driver for the
on-chip Tilera Gigabit Ethernet and XAUI interfaces.
To compile this driver as a module, choose M here: the module
will be called tile_net.
config XEN_NETDEV_FRONTEND
tristate "Xen network device frontend driver"
depends on XEN
select XEN_XENBUS_FRONTEND
default y
help
This driver provides support for Xen paravirtual network
devices exported by a Xen network driver domain (often
domain 0).
The corresponding Linux backend driver is enabled by the
CONFIG_XEN_NETDEV_BACKEND option.
If you are compiling a kernel for use as Xen guest, you
should say Y here. To compile this driver as a module, chose
M here: the module will be called xen-netfront.
config XEN_NETDEV_BACKEND
tristate "Xen backend network device"
depends on XEN_BACKEND
help
This driver allows the kernel to act as a Xen network driver
domain which exports paravirtual network devices to other
Xen domains. These devices can be accessed by any operating
system that implements a compatible front end.
The corresponding Linux frontend driver is enabled by the
CONFIG_XEN_NETDEV_FRONTEND configuration option.
The backend driver presents a standard network device
endpoint for each paravirtual network device to the driver
domain network stack. These can then be bridged or routed
etc in order to provide full network connectivity.
If you are compiling a kernel to run in a Xen network driver
domain (often this is domain 0) you should say Y here. To
compile this driver as a module, chose M here: the module
will be called xen-netback.
config RIONET
tristate "RapidIO Ethernet over messaging driver support"
depends on RAPIDIO
config RIONET_TX_SIZE
int "Number of outbound queue entries"
depends on RIONET
default "128"
config RIONET_RX_SIZE
int "Number of inbound queue entries"
depends on RIONET
default "128"
config FDDI
tristate "FDDI driver support"
depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
run over copper or fiber. If you are connected to such a network and
want a driver for the FDDI card in your computer, say Y here (and
then also Y to the driver for your FDDI card, below). Most people
will say N.
config DEFXX
tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
depends on FDDI && (PCI || EISA || TC)
---help---
This is support for the DIGITAL series of TURBOchannel (DEFTA),
EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
to a local FDDI network.
To compile this driver as a module, choose M here: the module
will be called defxx. If unsure, say N.
config DEFXX_MMIO
bool
prompt "Use MMIO instead of PIO" if PCI || EISA
depends on DEFXX
default n if PCI || EISA
default y
---help---
This instructs the driver to use EISA or PCI memory-mapped I/O
(MMIO) as appropriate instead of programmed I/O ports (PIO).
Enabling this gives an improvement in processing time in parts
of the driver, but it may cause problems with EISA (DEFEA)
adapters. TURBOchannel does not have the concept of I/O ports,
so MMIO is always used for these (DEFTA) adapters.
If unsure, say N.
config SKFP
tristate "SysKonnect FDDI PCI support"
depends on FDDI && PCI
select BITREVERSE
---help---
Say Y here if you have a SysKonnect FDDI PCI adapter.
The following adapters are supported by this driver:
- SK-5521 (SK-NET FDDI-UP)
- SK-5522 (SK-NET FDDI-UP DAS)
- SK-5541 (SK-NET FDDI-FP)
- SK-5543 (SK-NET FDDI-LP)
- SK-5544 (SK-NET FDDI-LP DAS)
- SK-5821 (SK-NET FDDI-UP64)
- SK-5822 (SK-NET FDDI-UP64 DAS)
- SK-5841 (SK-NET FDDI-FP64)
- SK-5843 (SK-NET FDDI-LP64)
- SK-5844 (SK-NET FDDI-LP64 DAS)
- Netelligent 100 FDDI DAS Fibre SC
- Netelligent 100 FDDI SAS Fibre SC
- Netelligent 100 FDDI DAS UTP
- Netelligent 100 FDDI SAS UTP
- Netelligent 100 FDDI SAS Fibre MIC
Read <file:Documentation/networking/skfp.txt> for information about
the driver.
Questions concerning this driver can be addressed to:
<linux@syskonnect.de>
To compile this driver as a module, choose M here: the module
will be called skfp. This is recommended.
config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
depends on EXPERIMENTAL && INET && PCI
help
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
can run over copper (25m) or fiber (300m on multi-mode or 10km on
single-mode). HIPPI networks are commonly used for clusters and to
connect to super computers. If you are connected to a HIPPI network
and have a HIPPI network card in your computer that you want to use
under Linux, say Y here (you must also remember to enable the driver
for your HIPPI card below). Most people will say N here.
config ROADRUNNER
tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
depends on HIPPI && PCI
help
Say Y here if this is your PCI HIPPI network card.
To compile this driver as a module, choose M here: the module
will be called rrunner. If unsure, say N.
config ROADRUNNER_LARGE_RINGS
bool "Use large TX/RX rings (EXPERIMENTAL)"
depends on ROADRUNNER
help
If you say Y here, the RoadRunner driver will preallocate up to 2 MB
of additional memory to allow for fastest operation, both for
transmitting and receiving. This memory cannot be used by any other
kernel code or by user space programs. Say Y here only if you have
the memory.
config PLIP
tristate "PLIP (parallel port) support"
depends on PARPORT
---help---
PLIP (Parallel Line Internet Protocol) is used to create a
reasonably fast mini network consisting of two (or, rarely, more)
local machines. A PLIP link from a Linux box is a popular means to
install a Linux distribution on a machine which doesn't have a
CD-ROM drive (a minimal system has to be transferred with floppies
first). The kernels on both machines need to have this PLIP option
enabled for this to work.
The PLIP driver has two modes, mode 0 and mode 1. The parallel
ports (the connectors at the computers with 25 holes) are connected
with "null printer" or "Turbo Laplink" cables which can transmit 4
bits at a time (mode 0) or with special PLIP cables, to be used on
bidirectional parallel ports only, which can transmit 8 bits at a
time (mode 1); you can find the wiring of these cables in
<file:Documentation/networking/PLIP.txt>. The cables can be up to
15m long. Mode 0 works also if one of the machines runs DOS/Windows
and has some PLIP software installed, e.g. the Crynwr PLIP packet
driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
and winsock or NCSA's telnet.
If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
as the NET-3-HOWTO, both available from
<http://www.tldp.org/docs.html#howto>. Note that the PLIP
protocol has been changed and this PLIP driver won't work together
with the PLIP support in Linux versions 1.0.x. This option enlarges
your kernel by about 8 KB.
To compile this driver as a module, choose M here. The module
will be called plip. If unsure, say Y or M, in case you buy
a laptop later.
config PPP
tristate "PPP (point-to-point protocol) support"
select SLHC
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
serial) lines. Ask your access provider if they support it, because
otherwise you can't use it; most Internet access providers these
days support PPP rather than SLIP.
To use PPP, you need an additional program called pppd as described
in the PPP-HOWTO, available at
<http://www.tldp.org/docs.html#howto>. Make sure that you have
the version of pppd recommended in <file:Documentation/Changes>.
The PPP option enlarges your kernel by about 16 KB.
There are actually two versions of PPP: the traditional PPP for
asynchronous lines, such as regular analog phone lines, and
synchronous PPP which can be used over digital ISDN lines for
example. If you want to use PPP over phone lines or other
asynchronous serial lines, you need to say Y (or M) here and also to
the next option, "PPP support for async serial ports". For PPP over
synchronous lines, you should say Y (or M) here and to "Support
synchronous PPP", below.
If you said Y to "Version information on all symbols" above, then
you cannot compile the PPP driver into the kernel; you can then only
compile it as a module. To compile this driver as a module, choose M
here. The module will be called ppp_generic.
config PPP_MULTILINK
bool "PPP multilink support (EXPERIMENTAL)"
depends on PPP && EXPERIMENTAL
help
PPP multilink is a protocol (defined in RFC 1990) which allows you
to combine several (logical or physical) lines into one logical PPP
connection, so that you can utilize your full bandwidth.
This has to be supported at the other end as well and you need a
version of the pppd daemon which understands the multilink protocol.
If unsure, say N.
config PPP_FILTER
bool "PPP filtering"
depends on PPP
help
Say Y here if you want to be able to filter the packets passing over
PPP interfaces. This allows you to control which packets count as
activity (i.e. which packets will reset the idle timer or bring up
a demand-dialed link) and which packets are to be dropped entirely.
You need to say Y here if you wish to use the pass-filter and
active-filter options to pppd.
If unsure, say N.
config PPP_ASYNC
tristate "PPP support for async serial ports"
depends on PPP
select CRC_CCITT
---help---
Say Y (or M) here if you want to be able to use PPP over standard
asynchronous serial ports, such as COM1 or COM2 on a PC. If you use
a modem (not a synchronous or ISDN modem) to contact your ISP, you
need this option.
To compile this driver as a module, choose M here.
If unsure, say Y.
config PPP_SYNC_TTY
tristate "PPP support for sync tty ports"
depends on PPP
help
Say Y (or M) here if you want to be able to use PPP over synchronous
(HDLC) tty devices, such as the SyncLink adapter. These devices
are often used for high-speed leased lines like T1/E1.
To compile this driver as a module, choose M here.
config PPP_DEFLATE
tristate "PPP Deflate compression"
depends on PPP
select ZLIB_INFLATE
select ZLIB_DEFLATE
---help---
Support for the Deflate compression method for PPP, which uses the
Deflate algorithm (the same algorithm that gzip uses) to compress
each PPP packet before it is sent over the wire. The machine at the
other end of the PPP link (usually your ISP) has to support the
Deflate compression method as well for this to be useful. Even if
they don't support it, it is safe to say Y here.
To compile this driver as a module, choose M here.
config PPP_BSDCOMP
tristate "PPP BSD-Compress compression"
depends on PPP
---help---
Support for the BSD-Compress compression method for PPP, which uses
the LZW compression method to compress each PPP packet before it is
sent over the wire. The machine at the other end of the PPP link
(usually your ISP) has to support the BSD-Compress compression
method as well for this to be useful. Even if they don't support it,
it is safe to say Y here.
The PPP Deflate compression method ("PPP Deflate compression",
above) is preferable to BSD-Compress, because it compresses better
and is patent-free.
Note that the BSD compression code will always be compiled as a
module; it is called bsd_comp and will show up in the directory
modules once you have said "make modules". If unsure, say N.
config PPP_MPPE
tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
depends on PPP && EXPERIMENTAL
select CRYPTO
select CRYPTO_SHA1
select CRYPTO_ARC4
select CRYPTO_ECB
---help---
Support for the MPPE Encryption protocol, as employed by the
Microsoft Point-to-Point Tunneling Protocol.
See http://pptpclient.sourceforge.net/ for information on
configuring PPTP clients and servers to utilize this method.
config PPPOE
tristate "PPP over Ethernet (EXPERIMENTAL)"
depends on EXPERIMENTAL && PPP
help
Support for PPP over Ethernet.
This driver requires the latest version of pppd from the CVS
repository at cvs.samba.org. Alternatively, see the
RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
which contains instruction on how to use this driver (under
the heading "Kernel mode PPPoE").
config PPTP
tristate "PPP over IPv4 (PPTP) (EXPERIMENTAL)"
depends on EXPERIMENTAL && PPP && NET_IPGRE_DEMUX
help
Support for PPP over IPv4.(Point-to-Point Tunneling Protocol)
This driver requires pppd plugin to work in client mode or
modified pptpd (poptop) to work in server mode.
See http://accel-pptp.sourceforge.net/ for information how to
utilize this module.
config PPPOATM
tristate "PPP over ATM"
depends on ATM && PPP
help
Support PPP (Point to Point Protocol) encapsulated in ATM frames.
This implementation does not yet comply with section 8 of RFC2364,
which can lead to bad results if the ATM peer loses state and
changes its encapsulation unilaterally.
config PPPOL2TP
tristate "PPP over L2TP (EXPERIMENTAL)"
depends on EXPERIMENTAL && L2TP && PPP
help
Support for PPP-over-L2TP socket family. L2TP is a protocol
used by ISPs and enterprises to tunnel PPP traffic over UDP
tunnels. L2TP is replacing PPTP for VPN uses.
config SLIP
tristate "SLIP (serial line) support"
---help---
Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
connect to your Internet service provider or to connect to some
other local Unix box or if you want to configure your Linux box as a
Slip/CSlip server for other people to dial in. SLIP (Serial Line
Internet Protocol) is a protocol used to send Internet traffic over
serial connections such as telephone lines or null modem cables;
nowadays, the protocol PPP is more commonly used for this same
purpose.
Normally, your access provider has to support SLIP in order for you
to be able to use it, but there is now a SLIP emulator called SLiRP
around (available from
<ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
allows you to use SLIP over a regular dial up shell connection. If
you plan to use SLiRP, make sure to say Y to CSLIP, below. The
NET-3-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, explains how to
configure SLIP. Note that you don't need this option if you just
want to run term (term is a program which gives you almost full
Internet connectivity if you have a regular dial up shell account on
some Internet connected Unix computer. Read
<http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
support will enlarge your kernel by about 4 KB. If unsure, say N.
To compile this driver as a module, choose M here. The module
will be called slip.
config SLIP_COMPRESSED
bool "CSLIP compressed headers"
depends on SLIP
select SLHC
---help---
This protocol is faster than SLIP because it uses compression on the
TCP/IP headers (not on the data itself), but it has to be supported
on both ends. Ask your access provider if you are not sure and
answer Y, just in case. You will still be able to use plain SLIP. If
you plan to use SLiRP, the SLIP emulator (available from
<ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
allows you to use SLIP over a regular dial up shell connection, you
definitely want to say Y here. The NET-3-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, explains how to configure
CSLIP. This won't enlarge your kernel.
config SLHC
tristate
help
This option enables Van Jacobsen serial line header compression
routines.
config SLIP_SMART
bool "Keepalive and linefill"
depends on SLIP
help
Adds additional capabilities to the SLIP driver to support the
RELCOM line fill and keepalive monitoring. Ideal on poor quality
analogue lines.
config SLIP_MODE_SLIP6
bool "Six bit SLIP encapsulation"
depends on SLIP
help
Just occasionally you may need to run IP over hostile serial
networks that don't pass all control characters or are only seven
bit. Saying Y here adds an extra mode you can use with SLIP:
"slip6". In this mode, SLIP will only send normal ASCII symbols over
the serial device. Naturally, this has to be supported at the other
end of the link as well. It's good enough, for example, to run IP
over the async ports of a Camtec JNT Pad. If unsure, say N.
config NET_FC
bool "Fibre Channel driver support"
depends on SCSI && PCI
help
Fibre Channel is a high speed serial protocol mainly used to connect
large storage devices to the computer; it is compatible with and
intended to replace SCSI.
If you intend to use Fibre Channel, you need to have a Fibre channel
adaptor card in your computer; say Y here and to the driver for your
adaptor below. You also should have said Y to "SCSI support" and
"SCSI generic support".
config NETCONSOLE
tristate "Network console logging support"
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
config NETCONSOLE_DYNAMIC
bool "Dynamic reconfiguration of logging targets"
depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
!(NETCONSOLE=y && CONFIGFS_FS=m)
help
This option enables the ability to dynamically reconfigure target
parameters (interface, IP addresses, port numbers, MAC addresses)
at runtime through a userspace interface exported using configfs.
See <file:Documentation/networking/netconsole.txt> for details.
config NETPOLL
def_bool NETCONSOLE
config NETPOLL_TRAP
bool "Netpoll traffic trapping"
default n
depends on NETPOLL
config NET_POLL_CONTROLLER
def_bool NETPOLL
config VIRTIO_NET
tristate "Virtio network driver (EXPERIMENTAL)"
depends on EXPERIMENTAL && VIRTIO
---help---
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
config VMXNET3
tristate "VMware VMXNET3 ethernet driver"
depends on PCI && INET
help
This driver supports VMware's vmxnet3 virtual ethernet NIC.
To compile this driver as a module, choose M here: the
module will be called vmxnet3.
endif # NETDEVICES
