menuconfig NEW_LEDS
bool "LED Support"
help
Say Y to enable Linux LED support. This allows control of supported
LEDs from both userspace and optionally, by kernel events (triggers).
This is not related to standard keyboard LEDs which are controlled
via the input system.
if NEW_LEDS
config LEDS_CLASS
tristate "LED Class Support"
help
This option enables the led sysfs class in /sys/class/leds. You'll
need this to do anything useful with LEDs. If unsure, say N.
comment "LED drivers"
config LEDS_ATMEL_PWM
tristate "LED Support using Atmel PWM outputs"
depends on LEDS_CLASS && ATMEL_PWM
help
This option enables support for LEDs driven using outputs
of the dedicated PWM controller found on newer Atmel SOCs.
config LEDS_CORGI
tristate "LED Support for the Sharp SL-C7x0 series"
depends on LEDS_CLASS && PXA_SHARP_C7xx
help
This option enables support for the LEDs on Sharp Zaurus
SL-C7x0 series (C700, C750, C760, C860).
config LEDS_LOCOMO
tristate "LED Support for Locomo device"
depends on LEDS_CLASS && SHARP_LOCOMO
help
This option enables support for the LEDs on Sharp Locomo.
Zaurus models SL-5500 and SL-5600.
config LEDS_SPITZ
tristate "LED Support for the Sharp SL-Cxx00 series"
depends on LEDS_CLASS && PXA_SHARP_Cxx00
help
This option enables support for the LEDs on Sharp Zaurus
SL-Cxx00 series (C1000, C3000, C3100).
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
help
This option enables support for LEDs connected to GPIO lines
on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
config LEDS_AMS_DELTA
tristate "LED Support for the Amstrad Delta (E3)"
depends on LEDS_CLASS && MACH_AMS_DELTA
help
This option enables support for the LEDs on Amstrad Delta (E3).
config LEDS_NET48XX
tristate "LED Support for Soekris net48xx series Error LED"
depends on LEDS_CLASS && SCx200_GPIO
help
This option enables support for the Soekris net4801 and net4826 error
LED.
config LEDS_WRAP
tristate "LED Support for the WRAP series LEDs"
depends on LEDS_CLASS && SCx200_GPIO
help
This option enables support for the PCEngines WRAP programmable LEDs.
config LEDS_H1940
tristate "LED Support for iPAQ H1940 device"
depends on LEDS_CLASS && ARCH_H1940
help
This option enables support for the LEDs on the h1940.
config LEDS_COBALT_QUBE
tristate "LED Support for the Cobalt Qube series front LED"
depends on LEDS_CLASS && MIPS_COBALT
help
This option enables support for the front LED on Cobalt Qube series
config LEDS_COBALT_RAQ
bool "LED Support for the Cobalt Raq series"
depends on LEDS_CLASS && MIPS_COBALT
select LEDS_TRIGGERS
help
This option enables support for the Cobalt Raq series LEDs.
config LEDS_HP6XX
tristate "LED Support for the HP Jornada 6xx"
depends on LEDS_CLASS && SH_HP6XX
help
This option enables led support for the handheld
HP Jornada 620/660/680/690.
config LEDS_GPIO
tristate "LED Support for GPIO connected LEDs"
depends on LEDS_CLASS && GENERIC_GPIO
help
This option enables support for the LEDs connected to GPIO
outputs. To be useful the particular board must have LEDs
and they must be connected to the GPIO lines.
config LEDS_CM_X270
tristate "LED Support for the CM-X270 LEDs"
depends on LEDS_CLASS && MACH_ARMCORE
help
This option enables support for the CM-X270 LEDs.
config LEDS_CLEVO_MAIL
tristate "Mail LED on Clevo notebook (EXPERIMENTAL)"
depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI && EXPERIMENTAL
help
This driver makes the mail LED accessible from userspace
programs through the leds subsystem. This LED have three
known mode: off, blink at 0.5Hz and blink at 1Hz.
The driver supports two kinds of interface: using ledtrig-timer
or through /sys/class/leds/clevo::mail/brightness. As this LED
cannot change it's brightness it blinks instead. The brightness
value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
blink at 1Hz.
This module can drive the mail LED for the following notebooks:
Clevo D400P
Clevo D410J
Clevo D410V
Clevo D400V/D470V (not tested, but might work)
Clevo M540N
Clevo M5x0N (not tested, but might work)
Positivo Mobile (Clevo M5x0V)
If your model is not listed here you can try the "nodetect"
module paramter.
To compile this driver as a module, choose M here: the
module will be called leds-clevo-mail.
comment "LED Triggers"
config LEDS_TRIGGERS
bool "LED Trigger support"
help
This option enables trigger support for the leds class.
These triggers allow kernel events to drive the LEDs and can
be configured via sysfs. If unsure, say Y.
config LEDS_TRIGGER_TIMER
tristate "LED Timer Trigger"
depends on LEDS_TRIGGERS
help
This allows LEDs to be controlled by a programmable timer
via sysfs. Some LED hardware can be programmed to start
blinking the LED without any further software interaction.
For more details read Documentation/leds-class.txt.
If unsure, say Y.
config LEDS_TRIGGER_IDE_DISK
bool "LED IDE Disk Trigger"
depends on LEDS_TRIGGERS && BLK_DEV_IDEDISK
help
This allows LEDs to be controlled by IDE disk activity.
If unsure, say Y.
config LEDS_TRIGGER_HEARTBEAT
tristate "LED Heartbeat Trigger"
depends on LEDS_TRIGGERS
help
This allows LEDs to be controlled by a CPU load average.
The flash frequency is a hyperbolic function of the 1-minute
load average.
If unsure, say Y.
endif # NEW_LEDS
