/* enternow_pci.c,v 0.99 2001/10/02
*
* enternow_pci.c Card-specific routines for
* Formula-n enter:now ISDN PCI ab
* Gerdes AG Power ISDN PCI
* Woerltronic SA 16 PCI
* (based on HiSax driver by Karsten Keil)
*
* Author Christoph Ersfeld <info@formula-n.de>
* Formula-n Europe AG (www.formula-n.com)
* previously Gerdes AG
*
*
* This file is (c) under GNU PUBLIC LICENSE
*
* Notes:
* This driver interfaces to netjet.c which performs B-channel
* processing.
*
* Version 0.99 is the first release of this driver and there are
* certainly a few bugs.
* It isn't testet on linux 2.4 yet, so consider this code to be
* beta.
*
* Please don't report me any malfunction without sending
* (compressed) debug-logs.
* It would be nearly impossible to retrace it.
*
* Log D-channel-processing as follows:
*
* 1. Load hisax with card-specific parameters, this example ist for
* Formula-n enter:now ISDN PCI and compatible
* (f.e. Gerdes Power ISDN PCI)
*
* modprobe hisax type=41 protocol=2 id=gerdes
*
* if you chose an other value for id, you need to modify the
* code below, too.
*
* 2. set debug-level
*
* hisaxctrl gerdes 1 0x3ff
* hisaxctrl gerdes 11 0x4f
* cat /dev/isdnctrl >> ~/log &
*
* Please take also a look into /var/log/messages if there is
* anything importand concerning HISAX.
*
*
* Credits:
* Programming the driver for Formula-n enter:now ISDN PCI and
* necessary the driver for the used Amd 7930 D-channel-controller
* was spnsored by Formula-n Europe AG.
* Thanks to Karsten Keil and Petr Novak, who gave me support in
* Hisax-specific questions.
* I want so say special thanks to Carl-Friedrich Braun, who had to
* answer a lot of questions about generally ISDN and about handling
* of the Amd-Chip.
*
*/
#include <linux/config.h>
#include "hisax.h"
#include "isac.h"
#include "isdnl1.h"
#include "amd7930_fn.h"
#include "enternow.h"
#include <linux/interrupt.h>
#include <linux/ppp_defs.h>
#include <linux/pci.h>
#include <linux/init.h>
#include "netjet.h"
const char *enternow_pci_rev = "$Revision: 1.1.4.5 $";
/* *************************** I/O-Interface functions ************************************* */
/* cs->readisac, macro rByteAMD */
BYTE
ReadByteAmd7930(struct IsdnCardState *cs, BYTE offset)
{
/* direktes Register */
if(offset < 8)
return (InByte(cs->hw.njet.isac + 4*offset));
/* indirektes Register */
else {
OutByte(cs->hw.njet.isac + 4*AMD_CR, offset);
return(InByte(cs->hw.njet.isac + 4*AMD_DR));
}
}
/* cs->writeisac, macro wByteAMD */
void
WriteByteAmd7930(struct IsdnCardState *cs, BYTE offset, BYTE value)
{
/* direktes Register */
if(offset < 8)
OutByte(cs->hw.njet.isac + 4*offset, value);
/* indirektes Register */
else {
OutByte(cs->hw.njet.isac + 4*AMD_CR, offset);
OutByte(cs->hw.njet.isac + 4*AMD_DR, value);
}
}
void
enpci_setIrqMask(struct IsdnCardState *cs, BYTE val) {
if (!val)
OutByte(cs->hw.njet.base+NETJET_IRQMASK1, 0x00);
else
OutByte(cs->hw.njet.base+NETJET_IRQMASK1, TJ_AMD_IRQ);
}
static BYTE dummyrr(struct IsdnCardState *cs, int chan, BYTE off)
{
return(5);
}
static void dummywr(struct IsdnCardState *cs, int chan, BYTE off, BYTE value)
{
}
/* ******************************************************************************** */
static void
reset_enpci(struct IsdnCardState *cs)
{
if (cs->debug & L1_DEB_ISAC)
debugl1(cs, "enter:now PCI: reset");
/* Reset on, (also for AMD) */
cs->hw.njet.ctrl_reg = 0x07;
OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg);
mdelay(20);
/* Reset off */
cs->hw.njet.ctrl_reg = 0x30;
OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg);
/* 20ms delay */
mdelay(20);
cs->hw.njet.auxd = 0; // LED-status
cs->hw.njet.dmactrl = 0;
OutByte(cs->hw.njet.base + NETJET_AUXCTRL, ~TJ_AMD_IRQ);
OutByte(cs->hw.njet.base + NETJET_IRQMASK1, TJ_AMD_IRQ);
OutByte(cs->hw.njet.auxa, cs->hw.njet.auxd); // LED off
}
static int
enpci_card_msg(struct IsdnCardState *cs, int mt, void *arg)
{
u_long flags;
BYTE *chan;
if (cs->debug & L1_DEB_ISAC)
debugl1(cs, "enter:now PCI: card_msg: 0x%04X", mt);
switch (mt) {
case CARD_RESET:
spin_lock_irqsave(&cs->lock, flags);
reset_enpci(cs);
Amd7930_init(cs);
spin_unlock_irqrestore(&cs->lock, flags);
break;
case CARD_RELEASE:
release_io_netjet(cs);
break;
case CARD_INIT:
reset_enpci(cs);
inittiger(cs);
/* irq must be on here */
Amd7930_init(cs);
break;
case CARD_TEST:
break;
case MDL_ASSIGN:
/* TEI assigned, LED1 on */
cs->hw.njet.auxd = TJ_AMD_IRQ << 1;
OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd);
break;
case MDL_REMOVE:
/* TEI removed, LEDs off */
cs->hw.njet.auxd = 0;
OutByte(cs->hw.njet.base + NETJET_AUXDATA, 0x00);
break;
case MDL_BC_ASSIGN:
/* activate B-channel */
chan = (BYTE *)arg;
if (cs->debug & L1_DEB_ISAC)
debugl1(cs, "enter:now PCI: assign phys. BC %d in AMD LMR1", *chan);
cs->dc.amd7930.ph_command(cs, (cs->dc.amd7930.lmr1 | (*chan + 1)), "MDL_BC_ASSIGN");
/* at least one b-channel in use, LED 2 on */
cs->hw.njet.auxd |= TJ_AMD_IRQ << 2;
OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd);
break;
case MDL_BC_RELEASE:
/* deactivate B-channel */
chan = (BYTE *)arg;
if (cs->debug & L1_DEB_ISAC)
debugl1(cs, "enter:now PCI: release phys. BC %d in Amd LMR1", *chan);
cs->dc.amd7930.ph_command(cs, (cs->dc.amd7930.lmr1 & ~(*chan + 1)), "MDL_BC_RELEASE");
/* no b-channel active -> LED2 off */
if (!(cs->dc.amd7930.lmr1 & 3)) {
cs->hw.njet.auxd &= ~(TJ_AMD_IRQ << 2);
OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd);
}
break;
default:
break;
}
return(0);
}
static irqreturn_t
enpci_interrupt(int intno, void *dev_id, struct pt_regs *regs)
{
struct IsdnCardState *cs = dev_id;
BYTE s0val, s1val, ir;
u_long flags;
spin_lock_irqsave(&cs->lock, flags);
s1val = InByte(cs->hw.njet.base + NETJET_IRQSTAT1);
/* AMD threw an interrupt */
if (!(s1val & TJ_AMD_IRQ)) {
/* read and clear interrupt-register */
ir = ReadByteAmd7930(cs, 0x00);
Amd7930_interrupt(cs, ir);
s1val = 1;
} else
s1val = 0;
s0val = InByte(cs->hw.njet.base + NETJET_IRQSTAT0);
if ((s0val | s1val)==0) { // shared IRQ
spin_unlock_irqrestore(&cs->lock, flags);
return IRQ_NONE;
}
if (s0val)
OutByte(cs->hw.njet.base + NETJET_IRQSTAT0, s0val);
/* DMA-Interrupt: B-channel-stuff */
/* set bits in sval to indicate which page is free */
if (inl(cs->hw.njet.base + NETJET_DMA_WRITE_ADR) <
inl(cs->hw.njet.base + NETJET_DMA_WRITE_IRQ))
/* the 2nd write page is free */
s0val = 0x08;
else /* the 1st write page is free */
s0val = 0x04;
if (inl(cs->hw.njet.base + NETJET_DMA_READ_ADR) <
inl(cs->hw.njet.base + NETJET_DMA_READ_IRQ))
/* the 2nd read page is free */
s0val = s0val | 0x02;
else /* the 1st read page is free */
s0val = s0val | 0x01;
if (s0val != cs->hw.njet.last_is0) /* we have a DMA interrupt */
{
if (test_and_set_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags)) {
spin_unlock_irqrestore(&cs->lock, flags);
return IRQ_HANDLED;
}
cs->hw.njet.irqstat0 = s0val;
if ((cs->hw.njet.irqstat0 & NETJET_IRQM0_READ) !=
(cs->hw.njet.last_is0 & NETJET_IRQM0_READ))
/* we have a read dma int */
read_tiger(cs);
if ((cs->hw.njet.irqstat0 & NETJET_IRQM0_WRITE) !=
(cs->hw.njet.last_is0 & NETJET_IRQM0_WRITE))
/* we have a write dma int */
write_tiger(cs);
test_and_clear_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags);
}
spin_unlock_irqrestore(&cs->lock, flags);
return IRQ_HANDLED;
}
static struct pci_dev *dev_netjet __initdata = NULL;
/* called by config.c */
int __init
setup_enternow_pci(struct IsdnCard *card)
{
int bytecnt;
struct IsdnCardState *cs = card->cs;
char tmp[64];
#ifdef CONFIG_PCI
#ifdef __BIG_ENDIAN
#error "not running on big endian machines now"
#endif
strcpy(tmp, enternow_pci_rev);
printk(KERN_INFO "HiSax: Formula-n Europe AG enter:now ISDN PCI driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_ENTERNOW)
return(0);
test_and_clear_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags);
for ( ;; )
{
if ((dev_netjet = pci_find_device(PCI_VENDOR_ID_TIGERJET,
PCI_DEVICE_ID_TIGERJET_300, dev_netjet))) {
if (pci_enable_device(dev_netjet))
return(0);
cs->irq = dev_netjet->irq;
if (!cs->irq) {
printk(KERN_WARNING "enter:now PCI: No IRQ for PCI card found\n");
return(0);
}
cs->hw.njet.base = pci_resource_start(dev_netjet, 0);
if (!cs->hw.njet.base) {
printk(KERN_WARNING "enter:now PCI: No IO-Adr for PCI card found\n");
return(0);
}
/* checks Sub-Vendor ID because system crashes with Traverse-Card */
if ((dev_netjet->subsystem_vendor != 0x55) ||
(dev_netjet->subsystem_device != 0x02)) {
printk(KERN_WARNING "enter:now: You tried to load this driver with an incompatible TigerJet-card\n");
printk(KERN_WARNING "Use type=20 for Traverse NetJet PCI Card.\n");
return(0);
}
} else {
printk(KERN_WARNING "enter:now PCI: No PCI card found\n");
return(0);
}
cs->hw.njet.auxa = cs->hw.njet.base + NETJET_AUXDATA;
cs->hw.njet.isac = cs->hw.njet.base + 0xC0; // Fenster zum AMD
/* Reset an */
cs->hw.njet.ctrl_reg = 0x07; // geändert von 0xff
OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg);
/* 20 ms Pause */
mdelay(20);
cs->hw.njet.ctrl_reg = 0x30; /* Reset Off and status read clear */
OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg);
mdelay(10);
cs->hw.njet.auxd = 0x00; // war 0xc0
cs->hw.njet.dmactrl = 0;
OutByte(cs->hw.njet.base + NETJET_AUXCTRL, ~TJ_AMD_IRQ);
OutByte(cs->hw.njet.base + NETJET_IRQMASK1, TJ_AMD_IRQ);
OutByte(cs->hw.njet.auxa, cs->hw.njet.auxd);
break;
}
#else
printk(KERN_WARNING "enter:now PCI: NO_PCI_BIOS\n");
printk(KERN_WARNING "enter:now PCI: unable to config Formula-n enter:now ISDN PCI ab\n");
return (0);
#endif /* CONFIG_PCI */
bytecnt = 256;
printk(KERN_INFO
"enter:now PCI: PCI card configured at 0x%lx IRQ %d\n",
cs->hw.njet.base, cs->irq);
if (!request_region(cs->hw.njet.base, bytecnt, "Fn_ISDN")) {
printk(KERN_WARNING
"HiSax: %s config port %lx-%lx already in use\n",
CardType[card->typ],
cs->hw.njet.base,
cs->hw.njet.base + bytecnt);
return (0);
}
setup_Amd7930(cs);
cs->hw.njet.last_is0 = 0;
/* macro rByteAMD */
cs->readisac = &ReadByteAmd7930;
/* macro wByteAMD */
cs->writeisac = &WriteByteAmd7930;
cs->dc.amd7930.setIrqMask = &enpci_setIrqMask;
cs->BC_Read_Reg = &dummyrr;
cs->BC_Write_Reg = &dummywr;
cs->BC_Send_Data = &netjet_fill_dma;
cs->cardmsg = &enpci_card_msg;
cs->irq_func = &enpci_interrupt;
cs->irq_flags |= SA_SHIRQ;
return (1);
}
