#
# Touchscreen driver configuration
#
menuconfig INPUT_TOUCHSCREEN
bool "Touchscreens"
help
Say Y here, and a list of supported touchscreens will be displayed.
This option doesn't affect the kernel.
If unsure, say Y.
if INPUT_TOUCHSCREEN
config OF_TOUCHSCREEN
def_tristate INPUT
depends on INPUT && OF
config TOUCHSCREEN_88PM860X
tristate "Marvell 88PM860x touchscreen"
depends on MFD_88PM860X
help
Say Y here if you have a 88PM860x PMIC and want to enable
support for the built-in touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called 88pm860x-ts.
config TOUCHSCREEN_ADS7846
tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
depends on SPI_MASTER
depends on HWMON = n || HWMON
help
Say Y here if you have a touchscreen interface using the
ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
and your board-specific setup code includes that in its
table of SPI devices.
If HWMON is selected, and the driver is told the reference voltage
on your board, you will also get hwmon interfaces for the voltage
(and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called ads7846.
config TOUCHSCREEN_AD7877
tristate "AD7877 based touchscreens"
depends on SPI_MASTER
help
Say Y here if you have a touchscreen interface using the
AD7877 controller, and your board-specific initialization
code includes that in its table of SPI devices.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called ad7877.
config TOUCHSCREEN_AD7879
tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
help
Say Y here if you want to support a touchscreen interface using
the AD7879-1/AD7889-1 controller.
You should select a bus connection too.
To compile this driver as a module, choose M here: the
module will be called ad7879.
config TOUCHSCREEN_AD7879_I2C
tristate "support I2C bus connection"
depends on TOUCHSCREEN_AD7879 && I2C
help
Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called ad7879-i2c.
config TOUCHSCREEN_AD7879_SPI
tristate "support SPI bus connection"
depends on TOUCHSCREEN_AD7879 && SPI_MASTER
help
Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called ad7879-spi.
config TOUCHSCREEN_AR1021_I2C
tristate "Microchip AR1021 i2c touchscreen"
depends on I2C && OF
help
Say Y here if you have the Microchip AR1021 touchscreen controller
chip in your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called ar1021_i2c.
config TOUCHSCREEN_ATMEL_MXT
tristate "Atmel mXT I2C Touchscreen"
depends on I2C
select FW_LOADER
help
Say Y here if you have Atmel mXT series I2C touchscreen,
such as AT42QT602240/ATMXT224, connected to your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called atmel_mxt_ts.
config TOUCHSCREEN_AUO_PIXCIR
tristate "AUO in-cell touchscreen using Pixcir ICs"
depends on I2C
depends on GPIOLIB
help
Say Y here if you have a AUO display with in-cell touchscreen
using Pixcir ICs.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called auo-pixcir-ts.
config TOUCHSCREEN_BU21013
tristate "BU21013 based touch panel controllers"
depends on I2C
help
Say Y here if you have a bu21013 touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called bu21013_ts.
config TOUCHSCREEN_CHIPONE_ICN8318
tristate "chipone icn8318 touchscreen controller"
depends on GPIOLIB
depends on I2C
depends on OF
help
Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called chipone_icn8318.
config TOUCHSCREEN_CY8CTMG110
tristate "cy8ctmg110 touchscreen"
depends on I2C
depends on GPIOLIB
help
Say Y here if you have a cy8ctmg110 capacitive touchscreen on
an AAVA device.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called cy8ctmg110_ts.
config TOUCHSCREEN_CYTTSP_CORE
tristate "Cypress TTSP touchscreen"
help
Say Y here if you have a touchscreen using controller from
the Cypress TrueTouch(tm) Standard Product family connected
to your system. You will also need to select appropriate
bus connection below.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called cyttsp_core.
config TOUCHSCREEN_CYTTSP_I2C
tristate "support I2C bus connection"
depends on TOUCHSCREEN_CYTTSP_CORE && I2C
help
Say Y here if the touchscreen is connected via I2C bus.
To compile this driver as a module, choose M here: the
module will be called cyttsp_i2c.
config TOUCHSCREEN_CYTTSP_SPI
tristate "support SPI bus connection"
depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
help
Say Y here if the touchscreen is connected via SPI bus.
To compile this driver as a module, choose M here: the
module will be called cyttsp_spi.
config TOUCHSCREEN_CYTTSP4_CORE
tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
help
Core driver for Cypress TrueTouch(tm) Standard Product
Generation4 touchscreen controllers.
Say Y here if you have a Cypress Gen4 touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here.
config TOUCHSCREEN_CYTTSP4_I2C
tristate "support I2C bus connection"
depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
help
Say Y here if the touchscreen is connected via I2C bus.
To compile this driver as a module, choose M here: the
module will be called cyttsp4_i2c.
config TOUCHSCREEN_CYTTSP4_SPI
tristate "support SPI bus connection"
depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
help
Say Y here if the touchscreen is connected via SPI bus.
To compile this driver as a module, choose M here: the
module will be called cyttsp4_spi.
config TOUCHSCREEN_DA9034
tristate "Touchscreen support for Dialog Semiconductor DA9034"
depends on PMIC_DA903X
default y
help
Say Y here to enable the support for the touchscreen found
on Dialog Semiconductor DA9034 PMIC.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called da9034-ts.
config TOUCHSCREEN_DA9052
tristate "Dialog DA9052/DA9053 TSI"
depends on PMIC_DA9052
help
Say Y here to support the touchscreen found on Dialog Semiconductor
DA9052-BC and DA9053-AA/Bx PMICs.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called da9052_tsi.
config TOUCHSCREEN_DYNAPRO
tristate "Dynapro serial touchscreen"
select SERIO
help
Say Y here if you have a Dynapro serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called dynapro.
config TOUCHSCREEN_HAMPSHIRE
tristate "Hampshire serial touchscreen"
select SERIO
help
Say Y here if you have a Hampshire serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called hampshire.
config TOUCHSCREEN_EETI
tristate "EETI touchscreen panel support"
depends on I2C
help
Say Y here to enable support for I2C connected EETI touch panels.
To compile this driver as a module, choose M here: the
module will be called eeti_ts.
config TOUCHSCREEN_EGALAX
tristate "EETI eGalax multi-touch panel support"
depends on I2C && OF
help
Say Y here to enable support for I2C connected EETI
eGalax multi-touch panels.
To compile this driver as a module, choose M here: the
module will be called egalax_ts.
config TOUCHSCREEN_FUJITSU
tristate "Fujitsu serial touchscreen"
select SERIO
help
Say Y here if you have the Fujitsu touchscreen (such as one
installed in Lifebook P series laptop) connected to your
system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called fujitsu-ts.
config TOUCHSCREEN_GOODIX
tristate "Goodix I2C touchscreen"
depends on I2C
help
Say Y here if you have the Goodix touchscreen (such as one
installed in Onda v975w tablets) connected to your
system. It also supports 5-finger chip models, which can be
found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called goodix.
config TOUCHSCREEN_ILI210X
tristate "Ilitek ILI210X based touchscreen"
depends on I2C
help
Say Y here if you have a ILI210X based touchscreen
controller. This driver supports models ILI2102,
ILI2102s, ILI2103, ILI2103s and ILI2105.
Such kind of chipsets can be found in Amazon Kindle Fire
touchscreens.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called ili210x.
config TOUCHSCREEN_IPROC
tristate "IPROC touch panel driver support"
depends on ARCH_BCM_IPROC || COMPILE_TEST
help
Say Y here if you want to add support for the IPROC touch
controller to your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called bcm_iproc_tsc.
config TOUCHSCREEN_S3C2410
tristate "Samsung S3C2410/generic touchscreen input driver"
depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
select S3C_ADC
help
Say Y here if you have the s3c2410 touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called s3c2410_ts.
config TOUCHSCREEN_GUNZE
tristate "Gunze AHL-51S touchscreen"
select SERIO
help
Say Y here if you have the Gunze AHL-51 touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called gunze.
config TOUCHSCREEN_ELAN
tristate "Elan eKTH I2C touchscreen"
depends on I2C
help
Say Y here if you have an Elan eKTH I2C touchscreen
connected to your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called elants_i2c.
config TOUCHSCREEN_ELO
tristate "Elo serial touchscreens"
select SERIO
help
Say Y here if you have an Elo serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called elo.
config TOUCHSCREEN_WACOM_W8001
tristate "Wacom W8001 penabled serial touchscreen"
select SERIO
help
Say Y here if you have an Wacom W8001 penabled serial touchscreen
connected to your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called wacom_w8001.
config TOUCHSCREEN_WACOM_I2C
tristate "Wacom Tablet support (I2C)"
depends on I2C
help
Say Y here if you want to use the I2C version of the Wacom
Pen Tablet.
If unsure, say N.
To compile this driver as a module, choose M here: the module
will be called wacom_i2c.
config TOUCHSCREEN_LPC32XX
tristate "LPC32XX touchscreen controller"
depends on ARCH_LPC32XX
help
Say Y here if you have a LPC32XX device and want
to support the built-in touchscreen.
To compile this driver as a module, choose M here: the
module will be called lpc32xx_ts.
config TOUCHSCREEN_MAX11801
tristate "MAX11801 based touchscreens"
depends on I2C
help
Say Y here if you have a MAX11801 based touchscreen
controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called max11801_ts.
config TOUCHSCREEN_MCS5000
tristate "MELFAS MCS-5000 touchscreen"
depends on I2C
help
Say Y here if you have the MELFAS MCS-5000 touchscreen controller
chip in your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mcs5000_ts.
config TOUCHSCREEN_MMS114
tristate "MELFAS MMS114 touchscreen"
depends on I2C
help
Say Y here if you have the MELFAS MMS114 touchscreen controller
chip in your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mms114.
config TOUCHSCREEN_MTOUCH
tristate "MicroTouch serial touchscreens"
select SERIO
help
Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mtouch.
config TOUCHSCREEN_INEXIO
tristate "iNexio serial touchscreens"
select SERIO
help
Say Y here if you have an iNexio serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called inexio.
config TOUCHSCREEN_INTEL_MID
tristate "Intel MID platform resistive touchscreen"
depends on INTEL_SCU_IPC
help
Say Y here if you have a Intel MID based touchscreen in
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called intel_mid_touch.
config TOUCHSCREEN_MK712
tristate "ICS MicroClock MK712 touchscreen"
help
Say Y here if you have the ICS MicroClock MK712 touchscreen
controller chip in your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mk712.
config TOUCHSCREEN_HP600
tristate "HP Jornada 6xx touchscreen"
depends on SH_HP6XX && SH_ADC
help
Say Y here if you have a HP Jornada 620/660/680/690 and want to
support the built-in touchscreen.
To compile this driver as a module, choose M here: the
module will be called hp680_ts_input.
config TOUCHSCREEN_HP7XX
tristate "HP Jornada 7xx touchscreen"
depends on SA1100_JORNADA720_SSP
help
Say Y here if you have a HP Jornada 710/720/728 and want
to support the built-in touchscreen.
To compile this driver as a module, choose M here: the
module will be called jornada720_ts.
config TOUCHSCREEN_IPAQ_MICRO
tristate "HP iPAQ Atmel Micro ASIC touchscreen"
depends on MFD_IPAQ_MICRO
help
Say Y here to enable support for the touchscreen attached to
the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called ipaq-micro-ts.
config TOUCHSCREEN_HTCPEN
tristate "HTC Shift X9500 touchscreen"
depends on ISA
help
Say Y here if you have an HTC Shift UMPC also known as HTC X9500
Clio / Shangrila and want to support the built-in touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called htcpen.
config TOUCHSCREEN_PENMOUNT
tristate "Penmount serial touchscreen"
select SERIO
help
Say Y here if you have a Penmount serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called penmount.
config TOUCHSCREEN_EDT_FT5X06
tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
depends on I2C
help
Say Y here if you have an EDT "Polytouch" touchscreen based
on the FocalTech FT5x06 family of controllers connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called edt-ft5x06.
config TOUCHSCREEN_MIGOR
tristate "Renesas MIGO-R touchscreen"
depends on SH_MIGOR && I2C
help
Say Y here to enable MIGO-R touchscreen support.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called migor_ts.
config TOUCHSCREEN_TOUCHRIGHT
tristate "Touchright serial touchscreen"
select SERIO
help
Say Y here if you have a Touchright serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called touchright.
config TOUCHSCREEN_TOUCHWIN
tristate "Touchwin serial touchscreen"
select SERIO
help
Say Y here if you have a Touchwin serial touchscreen connected to
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called touchwin.
config TOUCHSCREEN_TI_AM335X_TSC
tristate "TI Touchscreen Interface"
depends on MFD_TI_AM335X_TSCADC
help
Say Y here if you have 4/5/8 wire touchscreen controller
to be connected to the ADC controller on your TI AM335x SoC.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called ti_am335x_tsc.
config TOUCHSCREEN_UCB1400
tristate "Philips UCB1400 touchscreen"
depends on AC97_BUS
depends on UCB1400_CORE
help
This enables support for the Philips UCB1400 touchscreen interface.
The UCB1400 is an AC97 audio codec. The touchscreen interface
will be initialized only after the ALSA subsystem has been
brought up and the UCB1400 detected. You therefore have to
configure ALSA support as well (either built-in or modular,
independently of whether this driver is itself built-in or
modular) for this driver to work.
To compile this driver as a module, choose M here: the
module will be called ucb1400_ts.
config TOUCHSCREEN_PIXCIR
tristate "PIXCIR I2C touchscreens"
depends on I2C
help
Say Y here if you have a pixcir i2c touchscreen
controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called pixcir_i2c_ts.
config TOUCHSCREEN_WM831X
tristate "Support for WM831x touchscreen controllers"
depends on MFD_WM831X
help
This enables support for the touchscreen controller on the WM831x
series of PMICs.
To compile this driver as a module, choose M here: the
module will be called wm831x-ts.
config TOUCHSCREEN_WM97XX
tristate "Support for WM97xx AC97 touchscreen controllers"
depends on AC97_BUS
help
Say Y here if you have a Wolfson Microelectronics WM97xx
touchscreen connected to your system. Note that this option
only enables core driver, you will also need to select
support for appropriate chip below.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called wm97xx-ts.
config TOUCHSCREEN_WM9705
bool "WM9705 Touchscreen interface support"
depends on TOUCHSCREEN_WM97XX
default y
help
Say Y here to enable support for the Wolfson Microelectronics
WM9705 touchscreen controller.
config TOUCHSCREEN_WM9712
bool "WM9712 Touchscreen interface support"
depends on TOUCHSCREEN_WM97XX
default y
help
Say Y here to enable support for the Wolfson Microelectronics
WM9712 touchscreen controller.
config TOUCHSCREEN_WM9713
bool "WM9713 Touchscreen interface support"
depends on TOUCHSCREEN_WM97XX
default y
help
Say Y here to enable support for the Wolfson Microelectronics
WM9713 touchscreen controller.
config TOUCHSCREEN_WM97XX_ATMEL
tristate "WM97xx Atmel accelerated touch"
depends on TOUCHSCREEN_WM97XX && AVR32
help
Say Y here for support for streaming mode with WM97xx touchscreens
on Atmel AT91 or AVR32 systems with an AC97C module.
Be aware that this will use channel B in the controller for
streaming data, this must not conflict with other AC97C drivers.
If unsure, say N.
To compile this driver as a module, choose M here: the module will
be called atmel-wm97xx.
config TOUCHSCREEN_WM97XX_MAINSTONE
tristate "WM97xx Mainstone/Palm accelerated touch"
depends on TOUCHSCREEN_WM97XX && ARCH_PXA
help
Say Y here for support for streaming mode with WM97xx touchscreens
on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mainstone-wm97xx.
config TOUCHSCREEN_WM97XX_ZYLONITE
tristate "Zylonite accelerated touch"
depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
select TOUCHSCREEN_WM9713
help
Say Y here for support for streaming mode with the touchscreen
on Zylonite systems.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called zylonite-wm97xx.
config TOUCHSCREEN_USB_COMPOSITE
tristate "USB Touchscreen Driver"
depends on USB_ARCH_HAS_HCD
select USB
help
USB Touchscreen driver for:
- eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
- PanJit TouchSet USB
- 3M MicroTouch USB (EX II series)
- ITM
- some other eTurboTouch
- Gunze AHL61
- DMC TSC-10/25
- IRTOUCHSYSTEMS/UNITOP
- IdealTEK URTC1000
- GoTop Super_Q2/GogoPen/PenPower tablets
- JASTEC USB Touch Controller/DigiTech DTR-02U
- Zytronic controllers
- Elo TouchSystems 2700 IntelliTouch
- EasyTouch USB Touch Controller from Data Modul
- e2i (Mimo monitors)
Have a look at <http://linux.chapter7.ch/touchkit/> for
a usage description and the required user-space stuff.
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
config TOUCHSCREEN_MC13783
tristate "Freescale MC13783 touchscreen input driver"
depends on MFD_MC13XXX
help
Say Y here if you have an Freescale MC13783 PMIC on your
board and want to use its touchscreen
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called mc13783_ts.
config TOUCHSCREEN_USB_EGALAX
default y
bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_PANJIT
default y
bool "PanJit device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_3M
default y
bool "3M/Microtouch EX II series device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ITM
default y
bool "ITM device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ETURBO
default y
bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GUNZE
default y
bool "Gunze AHL61 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_DMC_TSC10
default y
bool "DMC TSC-10/25 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_IRTOUCH
default y
bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_IDEALTEK
default y
bool "IdealTEK URTC1000 device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GENERAL_TOUCH
default y
bool "GeneralTouch Touchscreen device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_GOTOP
default y
bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_JASTEC
default y
bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ELO
default y
bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_E2I
default y
bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ZYTRONIC
default y
bool "Zytronic controller" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_ETT_TC45USB
default y
bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_NEXIO
default y
bool "NEXIO/iNexio device support" if EXPERT
depends on TOUCHSCREEN_USB_COMPOSITE
config TOUCHSCREEN_USB_EASYTOUCH
default y
bool "EasyTouch USB Touch controller device support" if EMBEDDED
depends on TOUCHSCREEN_USB_COMPOSITE
help
Say Y here if you have an EasyTouch USB Touch controller.
If unsure, say N.
config TOUCHSCREEN_TOUCHIT213
tristate "Sahara TouchIT-213 touchscreen"
select SERIO
help
Say Y here if you have a Sahara TouchIT-213 Tablet PC.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called touchit213.
config TOUCHSCREEN_TSC_SERIO
tristate "TSC-10/25/40 serial touchscreen support"
select SERIO
help
Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
to your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called tsc40.
config TOUCHSCREEN_TSC2005
tristate "TSC2005 based touchscreens"
depends on SPI_MASTER
help
Say Y here if you have a TSC2005 based touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called tsc2005.
config TOUCHSCREEN_TSC2007
tristate "TSC2007 based touchscreens"
depends on I2C
help
Say Y here if you have a TSC2007 based touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called tsc2007.
config TOUCHSCREEN_W90X900
tristate "W90P910 touchscreen driver"
depends on ARCH_W90X900
help
Say Y here if you have a W90P910 based touchscreen.
To compile this driver as a module, choose M here: the
module will be called w90p910_ts.
config TOUCHSCREEN_PCAP
tristate "Motorola PCAP touchscreen"
depends on EZX_PCAP
help
Say Y here if you have a Motorola EZX telephone and
want to enable support for the built-in touchscreen.
To compile this driver as a module, choose M here: the
module will be called pcap_ts.
config TOUCHSCREEN_ST1232
tristate "Sitronix ST1232 touchscreen controllers"
depends on I2C
help
Say Y here if you want to support Sitronix ST1232
touchscreen controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called st1232_ts.
config TOUCHSCREEN_STMPE
tristate "STMicroelectronics STMPE touchscreens"
depends on MFD_STMPE
help
Say Y here if you want support for STMicroelectronics
STMPE touchscreen controllers.
To compile this driver as a module, choose M here: the
module will be called stmpe-ts.
config TOUCHSCREEN_SUN4I
tristate "Allwinner sun4i resistive touchscreen controller support"
depends on ARCH_SUNXI || COMPILE_TEST
depends on HWMON
depends on THERMAL || !THERMAL_OF
help
This selects support for the resistive touchscreen controller
found on Allwinner sunxi SoCs.
To compile this driver as a module, choose M here: the
module will be called sun4i-ts.
config TOUCHSCREEN_SUR40
tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
depends on USB
depends on MEDIA_USB_SUPPORT
select INPUT_POLLDEV
select VIDEOBUF2_DMA_SG
help
Say Y here if you want support for the Samsung SUR40 touchscreen
(also known as Microsoft Surface 2.0 or Microsoft PixelSense).
To compile this driver as a module, choose M here: the
module will be called sur40.
config TOUCHSCREEN_SX8654
tristate "Semtech SX8654 touchscreen"
depends on I2C
help
Say Y here if you have a Semtech SX8654 touchscreen controller.
If unsure, say N
To compile this driver as a module, choose M here: the
module will be called sx8654.
config TOUCHSCREEN_TPS6507X
tristate "TPS6507x based touchscreens"
depends on I2C
select INPUT_POLLDEV
help
Say Y here if you have a TPS6507x based touchscreen
controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called tps6507x_ts.
config TOUCHSCREEN_ZFORCE
tristate "Neonode zForce infrared touchscreens"
depends on I2C
depends on GPIOLIB
help
Say Y here if you have a touchscreen using the zforce
infraread technology from Neonode.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called zforce_ts.
endif
