/*
* SL82C105/Winbond 553 IDE driver
*
* Maintainer unknown.
*
* Drive tuning added from Rebel.com's kernel sources
* -- Russell King (15/11/98) linux@arm.linux.org.uk
*
* Merge in Russell's HW workarounds, fix various problems
* with the timing registers setup.
* -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
*
* Copyright (C) 2006-2007,2009 MontaVista Software, Inc. <source@mvista.com>
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*/
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <asm/io.h>
#define DRV_NAME "sl82c105"
/*
* SL82C105 PCI config register 0x40 bits.
*/
#define CTRL_IDE_IRQB (1 << 30)
#define CTRL_IDE_IRQA (1 << 28)
#define CTRL_LEGIRQ (1 << 11)
#define CTRL_P1F16 (1 << 5)
#define CTRL_P1EN (1 << 4)
#define CTRL_P0F16 (1 << 1)
#define CTRL_P0EN (1 << 0)
/*
* Convert a PIO mode and cycle time to the required on/off times
* for the interface. This has protection against runaway timings.
*/
static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio)
{
struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
unsigned int cmd_on, cmd_off;
u8 iordy = 0;
cmd_on = (t->active + 29) / 30;
cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30;
if (cmd_on == 0)
cmd_on = 1;
if (cmd_off == 0)
cmd_off = 1;
if (ide_pio_need_iordy(drive, pio))
iordy = 0x40;
return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy;
}
/*
* Configure the chipset for PIO mode.
*/
static void sl82c105_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long timings = (unsigned long)ide_get_drivedata(drive);
int reg = 0x44 + drive->dn * 4;
u16 drv_ctrl;
const u8 pio = drive->pio_mode - XFER_PIO_0;
drv_ctrl = get_pio_timings(drive, pio);
/*
* Store the PIO timings so that we can restore them
* in case DMA will be turned off...
*/
timings &= 0xffff0000;
timings |= drv_ctrl;
ide_set_drivedata(drive, (void *)timings);
pci_write_config_word(dev, reg, drv_ctrl);
pci_read_config_word (dev, reg, &drv_ctrl);
printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
ide_xfer_verbose(pio + XFER_PIO_0),
ide_pio_cycle_time(drive, pio), drv_ctrl);
}
/*
* Configure the chipset for DMA mode.
*/
static void sl82c105_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
unsigned long timings = (unsigned long)ide_get_drivedata(drive);
u16 drv_ctrl;
const u8 speed = drive->dma_mode;
drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
/*
* Store the DMA timings so that we can actually program
* them when DMA will be turned on...
*/
timings &= 0x0000ffff;
timings |= (unsigned long)drv_ctrl << 16;
ide_set_drivedata(drive, (void *)timings);
}
static int sl82c105_test_irq(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
pci_read_config_dword(dev, 0x40, &val);
return (val & mask) ? 1 : 0;
}
/*
* The SL82C105 holds off all IDE interrupts while in DMA mode until
* all DMA activity is completed. Sometimes this causes problems (eg,
* when the drive wants to report an error condition).
*
* 0x7e is a "chip testing" register. Bit 2 resets the DMA controller
* state machine. We need to kick this to work around various bugs.
*/
static inline void sl82c105_reset_host(struct pci_dev *dev)
{
u16 val;
pci_read_config_word(dev, 0x7e, &val);
pci_write_config_word(dev, 0x7e, val | (1 << 2));
pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
}
/*
* If we get an IRQ timeout, it might be that the DMA state machine
* got confused. Fix from Todd Inglett. Details from Winbond.
*
* This function is called when the IDE timer expires, the drive
* indicates that it is READY, and we were waiting for DMA to complete.
*/
static void sl82c105_dma_lost_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
u8 dma_cmd;
printk(KERN_WARNING "sl82c105: lost IRQ, resetting host\n");
/*
* Check the raw interrupt from the drive.
*/
pci_read_config_dword(dev, 0x40, &val);
if (val & mask)
printk(KERN_INFO "sl82c105: drive was requesting IRQ, "
"but host lost it\n");
/*
* Was DMA enabled? If so, disable it - we're resetting the
* host. The IDE layer will be handling the drive for us.
*/
dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
if (dma_cmd & 1) {
outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
printk(KERN_INFO "sl82c105: DMA was enabled\n");
}
sl82c105_reset_host(dev);
}
/*
* ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
* Winbond recommend that the DMA state machine is reset prior to
* setting the bus master DMA enable bit.
*
* The generic IDE core will have disabled the BMEN bit before this
* function is called.
*/
static void sl82c105_dma_start(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
int reg = 0x44 + drive->dn * 4;
pci_write_config_word(dev, reg,
(unsigned long)ide_get_drivedata(drive) >> 16);
sl82c105_reset_host(dev);
ide_dma_start(drive);
}
static void sl82c105_dma_clear(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
sl82c105_reset_host(dev);
}
static int sl82c105_dma_end(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
int reg = 0x44 + drive->dn * 4;
int ret = ide_dma_end(drive);
pci_write_config_word(dev, reg,
(unsigned long)ide_get_drivedata(drive));
return ret;
}
/*
* ATA reset will clear the 16 bits mode in the control
* register, we need to reprogram it
*/
static void sl82c105_resetproc(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
u32 val;
pci_read_config_dword(dev, 0x40, &val);
val |= (CTRL_P1F16 | CTRL_P0F16);
pci_write_config_dword(dev, 0x40, val);
}
/*
* Return the revision of the Winbond bridge
* which this function is part of.
*/
static u8 sl82c105_bridge_revision(struct pci_dev *dev)
{
struct pci_dev *bridge;
/*
* The bridge should be part of the same device, but function 0.
*/
bridge = pci_get_bus_and_slot(dev->bus->number,
PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
if (!bridge)
return -1;
/*
* Make sure it is a Winbond 553 and is an ISA bridge.
*/
if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
pci_dev_put(bridge);
return -1;
}
/*
* We need to find function 0's revision, not function 1
*/
pci_dev_put(bridge);
return bridge->revision;
}
/*
* Enable the PCI device
*
* --BenH: It's arch fixup code that should enable channels that
* have not been enabled by firmware. I decided we can still enable
* channel 0 here at least, but channel 1 has to be enabled by
* firmware or arch code. We still set both to 16 bits mode.
*/
static int init_chipset_sl82c105(struct pci_dev *dev)
{
u32 val;
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
return 0;
}
static const struct ide_port_ops sl82c105_port_ops = {
.set_pio_mode = sl82c105_set_pio_mode,
.set_dma_mode = sl82c105_set_dma_mode,
.resetproc = sl82c105_resetproc,
.test_irq = sl82c105_test_irq,
};
static const struct ide_dma_ops sl82c105_dma_ops = {
.dma_host_set = ide_dma_host_set,
.dma_setup = ide_dma_setup,
.dma_start = sl82c105_dma_start,
.dma_end = sl82c105_dma_end,
.dma_test_irq = ide_dma_test_irq,
.dma_lost_irq = sl82c105_dma_lost_irq,
.dma_timer_expiry = ide_dma_sff_timer_expiry,
.dma_clear = sl82c105_dma_clear,
.dma_sff_read_status = ide_dma_sff_read_status,
};
static const struct ide_port_info sl82c105_chipset __devinitdata = {
.name = DRV_NAME,
.init_chipset = init_chipset_sl82c105,
.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
.port_ops = &sl82c105_port_ops,
.dma_ops = &sl82c105_dma_ops,
.host_flags = IDE_HFLAG_IO_32BIT |
IDE_HFLAG_UNMASK_IRQS |
IDE_HFLAG_SERIALIZE_DMA |
IDE_HFLAG_NO_AUTODMA,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
};
static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ide_port_info d = sl82c105_chipset;
u8 rev = sl82c105_bridge_revision(dev);
if (rev <= 5) {
/*
* Never ever EVER under any circumstances enable
* DMA when the bridge is this old.
*/
printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge "
"revision %d, BM-DMA disabled\n", rev);
d.dma_ops = NULL;
d.mwdma_mask = 0;
d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA;
}
return ide_pci_init_one(dev, &d, NULL);
}
static const struct pci_device_id sl82c105_pci_tbl[] = {
{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
static struct pci_driver sl82c105_pci_driver = {
.name = "W82C105_IDE",
.id_table = sl82c105_pci_tbl,
.probe = sl82c105_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init sl82c105_ide_init(void)
{
return ide_pci_register_driver(&sl82c105_pci_driver);
}
static void __exit sl82c105_ide_exit(void)
{
pci_unregister_driver(&sl82c105_pci_driver);
}
module_init(sl82c105_ide_init);
module_exit(sl82c105_ide_exit);
MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
MODULE_LICENSE("GPL");
