/*
* linux/drivers/ide/ide-pmac.c
*
* Support for IDE interfaces on PowerMacs.
* These IDE interfaces are memory-mapped and have a DBDMA channel
* for doing DMA.
*
* Copyright (C) 1998-2003 Paul Mackerras & Ben. Herrenschmidt
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*
* Some code taken from drivers/ide/ide-dma.c:
*
* Copyright (c) 1995-1998 Mark Lord
*
* TODO: - Use pre-calculated (kauai) timing tables all the time and
* get rid of the "rounded" tables used previously, so we have the
* same table format for all controllers and can then just have one
* big table
*
*/
#include <linux/config.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/ide.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/pci.h>
#include <linux/adb.h>
#include <linux/pmu.h>
#include <linux/scatterlist.h>
#include <asm/prom.h>
#include <asm/io.h>
#include <asm/dbdma.h>
#include <asm/ide.h>
#include <asm/pci-bridge.h>
#include <asm/machdep.h>
#include <asm/pmac_feature.h>
#include <asm/sections.h>
#include <asm/irq.h>
#ifndef CONFIG_PPC64
#include <asm/mediabay.h>
#endif
#include "ide-timing.h"
#undef IDE_PMAC_DEBUG
#define DMA_WAIT_TIMEOUT 50
typedef struct pmac_ide_hwif {
unsigned long regbase;
int irq;
int kind;
int aapl_bus_id;
unsigned cable_80 : 1;
unsigned mediabay : 1;
unsigned broken_dma : 1;
unsigned broken_dma_warn : 1;
struct device_node* node;
struct macio_dev *mdev;
u32 timings[4];
volatile u32 __iomem * *kauai_fcr;
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/* Those fields are duplicating what is in hwif. We currently
* can't use the hwif ones because of some assumptions that are
* beeing done by the generic code about the kind of dma controller
* and format of the dma table. This will have to be fixed though.
*/
volatile struct dbdma_regs __iomem * dma_regs;
struct dbdma_cmd* dma_table_cpu;
#endif
} pmac_ide_hwif_t;
static pmac_ide_hwif_t pmac_ide[MAX_HWIFS] __pmacdata;
static int pmac_ide_count;
enum {
controller_ohare, /* OHare based */
controller_heathrow, /* Heathrow/Paddington */
controller_kl_ata3, /* KeyLargo ATA-3 */
controller_kl_ata4, /* KeyLargo ATA-4 */
controller_un_ata6, /* UniNorth2 ATA-6 */
controller_k2_ata6, /* K2 ATA-6 */
controller_sh_ata6, /* Shasta ATA-6 */
};
static const char* model_name[] = {
"OHare ATA", /* OHare based */
"Heathrow ATA", /* Heathrow/Paddington */
"KeyLargo ATA-3", /* KeyLargo ATA-3 (MDMA only) */
"KeyLargo ATA-4", /* KeyLargo ATA-4 (UDMA/66) */
"UniNorth ATA-6", /* UniNorth2 ATA-6 (UDMA/100) */
"K2 ATA-6", /* K2 ATA-6 (UDMA/100) */
"Shasta ATA-6", /* Shasta ATA-6 (UDMA/133) */
};
/*
* Extra registers, both 32-bit little-endian
*/
#define IDE_TIMING_CONFIG 0x200
#define IDE_INTERRUPT 0x300
/* Kauai (U2) ATA has different register setup */
#define IDE_KAUAI_PIO_CONFIG 0x200
#define IDE_KAUAI_ULTRA_CONFIG 0x210
#define IDE_KAUAI_POLL_CONFIG 0x220
/*
* Timing configuration register definitions
*/
/* Number of IDE_SYSCLK_NS ticks, argument is in nanoseconds */
#define SYSCLK_TICKS(t) (((t) + IDE_SYSCLK_NS - 1) / IDE_SYSCLK_NS)
#define SYSCLK_TICKS_66(t) (((t) + IDE_SYSCLK_66_NS - 1) / IDE_SYSCLK_66_NS)
#define IDE_SYSCLK_NS 30 /* 33Mhz cell */
#define IDE_SYSCLK_66_NS 15 /* 66Mhz cell */
/* 133Mhz cell, found in shasta.
* See comments about 100 Mhz Uninorth 2...
* Note that PIO_MASK and MDMA_MASK seem to overlap
*/
#define TR_133_PIOREG_PIO_MASK 0xff000fff
#define TR_133_PIOREG_MDMA_MASK 0x00fff800
#define TR_133_UDMAREG_UDMA_MASK 0x0003ffff
#define TR_133_UDMAREG_UDMA_EN 0x00000001
/* 100Mhz cell, found in Uninorth 2. I don't have much infos about
* this one yet, it appears as a pci device (106b/0033) on uninorth
* internal PCI bus and it's clock is controlled like gem or fw. It
* appears to be an evolution of keylargo ATA4 with a timing register
* extended to 2 32bits registers and a similar DBDMA channel. Other
* registers seem to exist but I can't tell much about them.
*
* So far, I'm using pre-calculated tables for this extracted from
* the values used by the MacOS X driver.
*
* The "PIO" register controls PIO and MDMA timings, the "ULTRA"
* register controls the UDMA timings. At least, it seems bit 0
* of this one enables UDMA vs. MDMA, and bits 4..7 are the
* cycle time in units of 10ns. Bits 8..15 are used by I don't
* know their meaning yet
*/
#define TR_100_PIOREG_PIO_MASK 0xff000fff
#define TR_100_PIOREG_MDMA_MASK 0x00fff000
#define TR_100_UDMAREG_UDMA_MASK 0x0000ffff
#define TR_100_UDMAREG_UDMA_EN 0x00000001
/* 66Mhz cell, found in KeyLargo. Can do ultra mode 0 to 2 on
* 40 connector cable and to 4 on 80 connector one.
* Clock unit is 15ns (66Mhz)
*
* 3 Values can be programmed:
* - Write data setup, which appears to match the cycle time. They
* also call it DIOW setup.
* - Ready to pause time (from spec)
* - Address setup. That one is weird. I don't see where exactly
* it fits in UDMA cycles, I got it's name from an obscure piece
* of commented out code in Darwin. They leave it to 0, we do as
* well, despite a comment that would lead to think it has a
* min value of 45ns.
* Apple also add 60ns to the write data setup (or cycle time ?) on
* reads.
*/
#define TR_66_UDMA_MASK 0xfff00000
#define TR_66_UDMA_EN 0x00100000 /* Enable Ultra mode for DMA */
#define TR_66_UDMA_ADDRSETUP_MASK 0xe0000000 /* Address setup */
#define TR_66_UDMA_ADDRSETUP_SHIFT 29
#define TR_66_UDMA_RDY2PAUS_MASK 0x1e000000 /* Ready 2 pause time */
#define TR_66_UDMA_RDY2PAUS_SHIFT 25
#define TR_66_UDMA_WRDATASETUP_MASK 0x01e00000 /* Write data setup time */
#define TR_66_UDMA_WRDATASETUP_SHIFT 21
#define TR_66_MDMA_MASK 0x000ffc00
#define TR_66_MDMA_RECOVERY_MASK 0x000f8000
#define TR_66_MDMA_RECOVERY_SHIFT 15
#define TR_66_MDMA_ACCESS_MASK 0x00007c00
#define TR_66_MDMA_ACCESS_SHIFT 10
#define TR_66_PIO_MASK 0x000003ff
#define TR_66_PIO_RECOVERY_MASK 0x000003e0
#define TR_66_PIO_RECOVERY_SHIFT 5
#define TR_66_PIO_ACCESS_MASK 0x0000001f
#define TR_66_PIO_ACCESS_SHIFT 0
/* 33Mhz cell, found in OHare, Heathrow (& Paddington) and KeyLargo
* Can do pio & mdma modes, clock unit is 30ns (33Mhz)
*
* The access time and recovery time can be programmed. Some older
* Darwin code base limit OHare to 150ns cycle time. I decided to do
* the same here fore safety against broken old hardware ;)
* The HalfTick bit, when set, adds half a clock (15ns) to the access
* time and removes one from recovery. It's not supported on KeyLargo
* implementation afaik. The E bit appears to be set for PIO mode 0 and
* is used to reach long timings used in this mode.
*/
#define TR_33_MDMA_MASK 0x003ff800
#define TR_33_MDMA_RECOVERY_MASK 0x001f0000
#define TR_33_MDMA_RECOVERY_SHIFT 16
#define TR_33_MDMA_ACCESS_MASK 0x0000f800
#define TR_33_MDMA_ACCESS_SHIFT 11
#define TR_33_MDMA_HALFTICK 0x00200000
#define TR_33_PIO_MASK 0x000007ff
#define TR_33_PIO_E 0x00000400
#define TR_33_PIO_RECOVERY_MASK 0x000003e0
#define TR_33_PIO_RECOVERY_SHIFT 5
#define TR_33_PIO_ACCESS_MASK 0x0000001f
#define TR_33_PIO_ACCESS_SHIFT 0
/*
* Interrupt register definitions
*/
#define IDE_INTR_DMA 0x80000000
#define IDE_INTR_DEVICE 0x40000000
/*
* FCR Register on Kauai. Not sure what bit 0x4 is ...
*/
#define KAUAI_FCR_UATA_MAGIC 0x00000004
#define KAUAI_FCR_UATA_RESET_N 0x00000002
#define KAUAI_FCR_UATA_ENABLE 0x00000001
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/* Rounded Multiword DMA timings
*
* I gave up finding a generic formula for all controller
* types and instead, built tables based on timing values
* used by Apple in Darwin's implementation.
*/
struct mdma_timings_t {
int accessTime;
int recoveryTime;
int cycleTime;
};
struct mdma_timings_t mdma_timings_33[] __pmacdata =
{
{ 240, 240, 480 },
{ 180, 180, 360 },
{ 135, 135, 270 },
{ 120, 120, 240 },
{ 105, 105, 210 },
{ 90, 90, 180 },
{ 75, 75, 150 },
{ 75, 45, 120 },
{ 0, 0, 0 }
};
struct mdma_timings_t mdma_timings_33k[] __pmacdata =
{
{ 240, 240, 480 },
{ 180, 180, 360 },
{ 150, 150, 300 },
{ 120, 120, 240 },
{ 90, 120, 210 },
{ 90, 90, 180 },
{ 90, 60, 150 },
{ 90, 30, 120 },
{ 0, 0, 0 }
};
struct mdma_timings_t mdma_timings_66[] __pmacdata =
{
{ 240, 240, 480 },
{ 180, 180, 360 },
{ 135, 135, 270 },
{ 120, 120, 240 },
{ 105, 105, 210 },
{ 90, 90, 180 },
{ 90, 75, 165 },
{ 75, 45, 120 },
{ 0, 0, 0 }
};
/* KeyLargo ATA-4 Ultra DMA timings (rounded) */
struct {
int addrSetup; /* ??? */
int rdy2pause;
int wrDataSetup;
} kl66_udma_timings[] __pmacdata =
{
{ 0, 180, 120 }, /* Mode 0 */
{ 0, 150, 90 }, /* 1 */
{ 0, 120, 60 }, /* 2 */
{ 0, 90, 45 }, /* 3 */
{ 0, 90, 30 } /* 4 */
};
/* UniNorth 2 ATA/100 timings */
struct kauai_timing {
int cycle_time;
u32 timing_reg;
};
static struct kauai_timing kauai_pio_timings[] __pmacdata =
{
{ 930 , 0x08000fff },
{ 600 , 0x08000a92 },
{ 383 , 0x0800060f },
{ 360 , 0x08000492 },
{ 330 , 0x0800048f },
{ 300 , 0x080003cf },
{ 270 , 0x080003cc },
{ 240 , 0x0800038b },
{ 239 , 0x0800030c },
{ 180 , 0x05000249 },
{ 120 , 0x04000148 }
};
static struct kauai_timing kauai_mdma_timings[] __pmacdata =
{
{ 1260 , 0x00fff000 },
{ 480 , 0x00618000 },
{ 360 , 0x00492000 },
{ 270 , 0x0038e000 },
{ 240 , 0x0030c000 },
{ 210 , 0x002cb000 },
{ 180 , 0x00249000 },
{ 150 , 0x00209000 },
{ 120 , 0x00148000 },
{ 0 , 0 },
};
static struct kauai_timing kauai_udma_timings[] __pmacdata =
{
{ 120 , 0x000070c0 },
{ 90 , 0x00005d80 },
{ 60 , 0x00004a60 },
{ 45 , 0x00003a50 },
{ 30 , 0x00002a30 },
{ 20 , 0x00002921 },
{ 0 , 0 },
};
static struct kauai_timing shasta_pio_timings[] __pmacdata =
{
{ 930 , 0x08000fff },
{ 600 , 0x0A000c97 },
{ 383 , 0x07000712 },
{ 360 , 0x040003cd },
{ 330 , 0x040003cd },
{ 300 , 0x040003cd },
{ 270 , 0x040003cd },
{ 240 , 0x040003cd },
{ 239 , 0x040003cd },
{ 180 , 0x0400028b },
{ 120 , 0x0400010a }
};
static struct kauai_timing shasta_mdma_timings[] __pmacdata =
{
{ 1260 , 0x00fff000 },
{ 480 , 0x00820800 },
{ 360 , 0x00820800 },
{ 270 , 0x00820800 },
{ 240 , 0x00820800 },
{ 210 , 0x00820800 },
{ 180 , 0x00820800 },
{ 150 , 0x0028b000 },
{ 120 , 0x001ca000 },
{ 0 , 0 },
};
static struct kauai_timing shasta_udma133_timings[] __pmacdata =
{
{ 120 , 0x00035901, },
{ 90 , 0x000348b1, },
{ 60 , 0x00033881, },
{ 45 , 0x00033861, },
{ 30 , 0x00033841, },
{ 20 , 0x00033031, },
{ 15 , 0x00033021, },
{ 0 , 0 },
};
static inline u32
kauai_lookup_timing(struct kauai_timing* table, int cycle_time)
{
int i;
for (i=0; table[i].cycle_time; i++)
if (cycle_time > table[i+1].cycle_time)
return table[i].timing_reg;
return 0;
}
/* allow up to 256 DBDMA commands per xfer */
#define MAX_DCMDS 256
/*
* Wait 1s for disk to answer on IDE bus after a hard reset
* of the device (via GPIO/FCR).
*
* Some devices seem to "pollute" the bus even after dropping
* the BSY bit (typically some combo drives slave on the UDMA
* bus) after a hard reset. Since we hard reset all drives on
* KeyLargo ATA66, we have to keep that delay around. I may end
* up not hard resetting anymore on these and keep the delay only
* for older interfaces instead (we have to reset when coming
* from MacOS...) --BenH.
*/
#define IDE_WAKEUP_DELAY (1*HZ)
static void pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif);
static int pmac_ide_build_dmatable(ide_drive_t *drive, struct request *rq);
static int pmac_ide_tune_chipset(ide_drive_t *drive, u8 speed);
static void pmac_ide_tuneproc(ide_drive_t *drive, u8 pio);
static void pmac_ide_selectproc(ide_drive_t *drive);
static void pmac_ide_kauai_selectproc(ide_drive_t *drive);
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
/*
* Below is the code for blinking the laptop LED along with hard
* disk activity.
*/
#ifdef CONFIG_BLK_DEV_IDE_PMAC_BLINK
/* Set to 50ms minimum led-on time (also used to limit frequency
* of requests sent to the PMU
*/
#define PMU_HD_BLINK_TIME (HZ/50)
static struct adb_request pmu_blink_on, pmu_blink_off;
static spinlock_t pmu_blink_lock;
static unsigned long pmu_blink_stoptime;
static int pmu_blink_ledstate;
static struct timer_list pmu_blink_timer;
static int pmu_ide_blink_enabled;
static void
pmu_hd_blink_timeout(unsigned long data)
{
unsigned long flags;
spin_lock_irqsave(&pmu_blink_lock, flags);
/* We may have been triggered again in a racy way, check
* that we really want to switch it off
*/
if (time_after(pmu_blink_stoptime, jiffies))
goto done;
/* Previous req. not complete, try 100ms more */
if (pmu_blink_off.complete == 0)
mod_timer(&pmu_blink_timer, jiffies + PMU_HD_BLINK_TIME);
else if (pmu_blink_ledstate) {
pmu_request(&pmu_blink_off, NULL, 4, 0xee, 4, 0, 0);
pmu_blink_ledstate = 0;
}
done:
spin_unlock_irqrestore(&pmu_blink_lock, flags);
}
static void
pmu_hd_kick_blink(void *data, int rw)
{
unsigned long flags;
pmu_blink_stoptime = jiffies + PMU_HD_BLINK_TIME;
wmb();
mod_timer(&pmu_blink_timer, pmu_blink_stoptime);
/* Fast path when LED is already ON */
if (pmu_blink_ledstate == 1)
return;
spin_lock_irqsave(&pmu_blink_lock, flags);
if (pmu_blink_on.complete && !pmu_blink_ledstate) {
pmu_request(&pmu_blink_on, NULL, 4, 0xee, 4, 0, 1);
pmu_blink_ledstate = 1;
}
spin_unlock_irqrestore(&pmu_blink_lock, flags);
}
static int
pmu_hd_blink_init(void)
{
struct device_node *dt;
const char *model;
/* Currently, I only enable this feature on KeyLargo based laptops,
* older laptops may support it (at least heathrow/paddington) but
* I don't feel like loading those venerable old machines with so
* much additional interrupt & PMU activity...
*/
if (pmu_get_model() != PMU_KEYLARGO_BASED)
return 0;
dt = find_devices("device-tree");
if (dt == NULL)
return 0;
model = (const char *)get_property(dt, "model", NULL);
if (model == NULL)
return 0;
if (strncmp(model, "PowerBook", strlen("PowerBook")) != 0 &&
strncmp(model, "iBook", strlen("iBook")) != 0)
return 0;
pmu_blink_on.complete = 1;
pmu_blink_off.complete = 1;
spin_lock_init(&pmu_blink_lock);
init_timer(&pmu_blink_timer);
pmu_blink_timer.function = pmu_hd_blink_timeout;
return 1;
}
#endif /* CONFIG_BLK_DEV_IDE_PMAC_BLINK */
/*
* N.B. this can't be an initfunc, because the media-bay task can
* call ide_[un]register at any time.
*/
void __pmac
pmac_ide_init_hwif_ports(hw_regs_t *hw,
unsigned long data_port, unsigned long ctrl_port,
int *irq)
{
int i, ix;
if (data_port == 0)
return;
for (ix = 0; ix < MAX_HWIFS; ++ix)
if (data_port == pmac_ide[ix].regbase)
break;
if (ix >= MAX_HWIFS) {
/* Probably a PCI interface... */
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; ++i)
hw->io_ports[i] = data_port + i - IDE_DATA_OFFSET;
hw->io_ports[IDE_CONTROL_OFFSET] = ctrl_port;
return;
}
for (i = 0; i < 8; ++i)
hw->io_ports[i] = data_port + i * 0x10;
hw->io_ports[8] = data_port + 0x160;
if (irq != NULL)
*irq = pmac_ide[ix].irq;
}
#define PMAC_IDE_REG(x) ((void __iomem *)(IDE_DATA_REG+(x)))
/*
* Apply the timings of the proper unit (master/slave) to the shared
* timing register when selecting that unit. This version is for
* ASICs with a single timing register
*/
static void __pmac
pmac_ide_selectproc(ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
if (pmif == NULL)
return;
if (drive->select.b.unit & 0x01)
writel(pmif->timings[1], PMAC_IDE_REG(IDE_TIMING_CONFIG));
else
writel(pmif->timings[0], PMAC_IDE_REG(IDE_TIMING_CONFIG));
(void)readl(PMAC_IDE_REG(IDE_TIMING_CONFIG));
}
/*
* Apply the timings of the proper unit (master/slave) to the shared
* timing register when selecting that unit. This version is for
* ASICs with a dual timing register (Kauai)
*/
static void __pmac
pmac_ide_kauai_selectproc(ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
if (pmif == NULL)
return;
if (drive->select.b.unit & 0x01) {
writel(pmif->timings[1], PMAC_IDE_REG(IDE_KAUAI_PIO_CONFIG));
writel(pmif->timings[3], PMAC_IDE_REG(IDE_KAUAI_ULTRA_CONFIG));
} else {
writel(pmif->timings[0], PMAC_IDE_REG(IDE_KAUAI_PIO_CONFIG));
writel(pmif->timings[2], PMAC_IDE_REG(IDE_KAUAI_ULTRA_CONFIG));
}
(void)readl(PMAC_IDE_REG(IDE_KAUAI_PIO_CONFIG));
}
/*
* Force an update of controller timing values for a given drive
*/
static void __pmac
pmac_ide_do_update_timings(ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
if (pmif == NULL)
return;
if (pmif->kind == controller_sh_ata6 ||
pmif->kind == controller_un_ata6 ||
pmif->kind == controller_k2_ata6)
pmac_ide_kauai_selectproc(drive);
else
pmac_ide_selectproc(drive);
}
static void
pmac_outbsync(ide_drive_t *drive, u8 value, unsigned long port)
{
u32 tmp;
writeb(value, (void __iomem *) port);
tmp = readl(PMAC_IDE_REG(IDE_TIMING_CONFIG));
}
/*
* Send the SET_FEATURE IDE command to the drive and update drive->id with
* the new state. We currently don't use the generic routine as it used to
* cause various trouble, especially with older mediabays.
* This code is sometimes triggering a spurrious interrupt though, I need
* to sort that out sooner or later and see if I can finally get the
* common version to work properly in all cases
*/
static int __pmac
pmac_ide_do_setfeature(ide_drive_t *drive, u8 command)
{
ide_hwif_t *hwif = HWIF(drive);
int result = 1;
disable_irq_nosync(hwif->irq);
udelay(1);
SELECT_DRIVE(drive);
SELECT_MASK(drive, 0);
udelay(1);
/* Get rid of pending error state */
(void) hwif->INB(IDE_STATUS_REG);
/* Timeout bumped for some powerbooks */
if (wait_for_ready(drive, 2000)) {
/* Timeout bumped for some powerbooks */
printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
"before SET_FEATURE!\n", drive->name);
goto out;
}
udelay(10);
hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
hwif->OUTB(command, IDE_NSECTOR_REG);
hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
udelay(1);
/* Timeout bumped for some powerbooks */
result = wait_for_ready(drive, 2000);
hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
if (result)
printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
"after SET_FEATURE !\n", drive->name);
out:
SELECT_MASK(drive, 0);
if (result == 0) {
drive->id->dma_ultra &= ~0xFF00;
drive->id->dma_mword &= ~0x0F00;
drive->id->dma_1word &= ~0x0F00;
switch(command) {
case XFER_UDMA_7:
drive->id->dma_ultra |= 0x8080; break;
case XFER_UDMA_6:
drive->id->dma_ultra |= 0x4040; break;
case XFER_UDMA_5:
drive->id->dma_ultra |= 0x2020; break;
case XFER_UDMA_4:
drive->id->dma_ultra |= 0x1010; break;
case XFER_UDMA_3:
drive->id->dma_ultra |= 0x0808; break;
case XFER_UDMA_2:
drive->id->dma_ultra |= 0x0404; break;
case XFER_UDMA_1:
drive->id->dma_ultra |= 0x0202; break;
case XFER_UDMA_0:
drive->id->dma_ultra |= 0x0101; break;
case XFER_MW_DMA_2:
drive->id->dma_mword |= 0x0404; break;
case XFER_MW_DMA_1:
drive->id->dma_mword |= 0x0202; break;
case XFER_MW_DMA_0:
drive->id->dma_mword |= 0x0101; break;
case XFER_SW_DMA_2:
drive->id->dma_1word |= 0x0404; break;
case XFER_SW_DMA_1:
drive->id->dma_1word |= 0x0202; break;
case XFER_SW_DMA_0:
drive->id->dma_1word |= 0x0101; break;
default: break;
}
}
enable_irq(hwif->irq);
return result;
}
/*
* Old tuning functions (called on hdparm -p), sets up drive PIO timings
*/
static void __pmac
pmac_ide_tuneproc(ide_drive_t *drive, u8 pio)
{
ide_pio_data_t d;
u32 *timings;
unsigned accessTicks, recTicks;
unsigned accessTime, recTime;
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
if (pmif == NULL)
return;
/* which drive is it ? */
timings = &pmif->timings[drive->select.b.unit & 0x01];
pio = ide_get_best_pio_mode(drive, pio, 4, &d);
switch (pmif->kind) {
case controller_sh_ata6: {
/* 133Mhz cell */
u32 tr = kauai_lookup_timing(shasta_pio_timings, d.cycle_time);
if (tr == 0)
return;
*timings = ((*timings) & ~TR_133_PIOREG_PIO_MASK) | tr;
break;
}
case controller_un_ata6:
case controller_k2_ata6: {
/* 100Mhz cell */
u32 tr = kauai_lookup_timing(kauai_pio_timings, d.cycle_time);
if (tr == 0)
return;
*timings = ((*timings) & ~TR_100_PIOREG_PIO_MASK) | tr;
break;
}
case controller_kl_ata4:
/* 66Mhz cell */
recTime = d.cycle_time - ide_pio_timings[pio].active_time
- ide_pio_timings[pio].setup_time;
recTime = max(recTime, 150U);
accessTime = ide_pio_timings[pio].active_time;
accessTime = max(accessTime, 150U);
accessTicks = SYSCLK_TICKS_66(accessTime);
accessTicks = min(accessTicks, 0x1fU);
recTicks = SYSCLK_TICKS_66(recTime);
recTicks = min(recTicks, 0x1fU);
*timings = ((*timings) & ~TR_66_PIO_MASK) |
(accessTicks << TR_66_PIO_ACCESS_SHIFT) |
(recTicks << TR_66_PIO_RECOVERY_SHIFT);
break;
default: {
/* 33Mhz cell */
int ebit = 0;
recTime = d.cycle_time - ide_pio_timings[pio].active_time
- ide_pio_timings[pio].setup_time;
recTime = max(recTime, 150U);
accessTime = ide_pio_timings[pio].active_time;
accessTime = max(accessTime, 150U);
accessTicks = SYSCLK_TICKS(accessTime);
accessTicks = min(accessTicks, 0x1fU);
accessTicks = max(accessTicks, 4U);
recTicks = SYSCLK_TICKS(recTime);
recTicks = min(recTicks, 0x1fU);
recTicks = max(recTicks, 5U) - 4;
if (recTicks > 9) {
recTicks--; /* guess, but it's only for PIO0, so... */
ebit = 1;
}
*timings = ((*timings) & ~TR_33_PIO_MASK) |
(accessTicks << TR_33_PIO_ACCESS_SHIFT) |
(recTicks << TR_33_PIO_RECOVERY_SHIFT);
if (ebit)
*timings |= TR_33_PIO_E;
break;
}
}
#ifdef IDE_PMAC_DEBUG
printk(KERN_ERR "%s: Set PIO timing for mode %d, reg: 0x%08x\n",
drive->name, pio, *timings);
#endif
if (drive->select.all == HWIF(drive)->INB(IDE_SELECT_REG))
pmac_ide_do_update_timings(drive);
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/*
* Calculate KeyLargo ATA/66 UDMA timings
*/
static int __pmac
set_timings_udma_ata4(u32 *timings, u8 speed)
{
unsigned rdyToPauseTicks, wrDataSetupTicks, addrTicks;
if (speed > XFER_UDMA_4)
return 1;
rdyToPauseTicks = SYSCLK_TICKS_66(kl66_udma_timings[speed & 0xf].rdy2pause);
wrDataSetupTicks = SYSCLK_TICKS_66(kl66_udma_timings[speed & 0xf].wrDataSetup);
addrTicks = SYSCLK_TICKS_66(kl66_udma_timings[speed & 0xf].addrSetup);
*timings = ((*timings) & ~(TR_66_UDMA_MASK | TR_66_MDMA_MASK)) |
(wrDataSetupTicks << TR_66_UDMA_WRDATASETUP_SHIFT) |
(rdyToPauseTicks << TR_66_UDMA_RDY2PAUS_SHIFT) |
(addrTicks <<TR_66_UDMA_ADDRSETUP_SHIFT) |
TR_66_UDMA_EN;
#ifdef IDE_PMAC_DEBUG
printk(KERN_ERR "ide_pmac: Set UDMA timing for mode %d, reg: 0x%08x\n",
speed & 0xf, *timings);
#endif
return 0;
}
/*
* Calculate Kauai ATA/100 UDMA timings
*/
static int __pmac
set_timings_udma_ata6(u32 *pio_timings, u32 *ultra_timings, u8 speed)
{
struct ide_timing *t = ide_timing_find_mode(speed);
u32 tr;
if (speed > XFER_UDMA_5 || t == NULL)
return 1;
tr = kauai_lookup_timing(kauai_udma_timings, (int)t->udma);
if (tr == 0)
return 1;
*ultra_timings = ((*ultra_timings) & ~TR_100_UDMAREG_UDMA_MASK) | tr;
*ultra_timings = (*ultra_timings) | TR_100_UDMAREG_UDMA_EN;
return 0;
}
/*
* Calculate Shasta ATA/133 UDMA timings
*/
static int __pmac
set_timings_udma_shasta(u32 *pio_timings, u32 *ultra_timings, u8 speed)
{
struct ide_timing *t = ide_timing_find_mode(speed);
u32 tr;
if (speed > XFER_UDMA_6 || t == NULL)
return 1;
tr = kauai_lookup_timing(shasta_udma133_timings, (int)t->udma);
if (tr == 0)
return 1;
*ultra_timings = ((*ultra_timings) & ~TR_133_UDMAREG_UDMA_MASK) | tr;
*ultra_timings = (*ultra_timings) | TR_133_UDMAREG_UDMA_EN;
return 0;
}
/*
* Calculate MDMA timings for all cells
*/
static int __pmac
set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
u8 speed, int drive_cycle_time)
{
int cycleTime, accessTime = 0, recTime = 0;
unsigned accessTicks, recTicks;
struct mdma_timings_t* tm = NULL;
int i;
/* Get default cycle time for mode */
switch(speed & 0xf) {
case 0: cycleTime = 480; break;
case 1: cycleTime = 150; break;
case 2: cycleTime = 120; break;
default:
return 1;
}
/* Adjust for drive */
if (drive_cycle_time && drive_cycle_time > cycleTime)
cycleTime = drive_cycle_time;
/* OHare limits according to some old Apple sources */
if ((intf_type == controller_ohare) && (cycleTime < 150))
cycleTime = 150;
/* Get the proper timing array for this controller */
switch(intf_type) {
case controller_sh_ata6:
case controller_un_ata6:
case controller_k2_ata6:
break;
case controller_kl_ata4:
tm = mdma_timings_66;
break;
case controller_kl_ata3:
tm = mdma_timings_33k;
break;
default:
tm = mdma_timings_33;
break;
}
if (tm != NULL) {
/* Lookup matching access & recovery times */
i = -1;
for (;;) {
if (tm[i+1].cycleTime < cycleTime)
break;
i++;
}
if (i < 0)
return 1;
cycleTime = tm[i].cycleTime;
accessTime = tm[i].accessTime;
recTime = tm[i].recoveryTime;
#ifdef IDE_PMAC_DEBUG
printk(KERN_ERR "%s: MDMA, cycleTime: %d, accessTime: %d, recTime: %d\n",
drive->name, cycleTime, accessTime, recTime);
#endif
}
switch(intf_type) {
case controller_sh_ata6: {
/* 133Mhz cell */
u32 tr = kauai_lookup_timing(shasta_mdma_timings, cycleTime);
if (tr == 0)
return 1;
*timings = ((*timings) & ~TR_133_PIOREG_MDMA_MASK) | tr;
*timings2 = (*timings2) & ~TR_133_UDMAREG_UDMA_EN;
}
case controller_un_ata6:
case controller_k2_ata6: {
/* 100Mhz cell */
u32 tr = kauai_lookup_timing(kauai_mdma_timings, cycleTime);
if (tr == 0)
return 1;
*timings = ((*timings) & ~TR_100_PIOREG_MDMA_MASK) | tr;
*timings2 = (*timings2) & ~TR_100_UDMAREG_UDMA_EN;
}
break;
case controller_kl_ata4:
/* 66Mhz cell */
accessTicks = SYSCLK_TICKS_66(accessTime);
accessTicks = min(accessTicks, 0x1fU);
accessTicks = max(accessTicks, 0x1U);
recTicks = SYSCLK_TICKS_66(recTime);
recTicks = min(recTicks, 0x1fU);
recTicks = max(recTicks, 0x3U);
/* Clear out mdma bits and disable udma */
*timings = ((*timings) & ~(TR_66_MDMA_MASK | TR_66_UDMA_MASK)) |
(accessTicks << TR_66_MDMA_ACCESS_SHIFT) |
(recTicks << TR_66_MDMA_RECOVERY_SHIFT);
break;
case controller_kl_ata3:
/* 33Mhz cell on KeyLargo */
accessTicks = SYSCLK_TICKS(accessTime);
accessTicks = max(accessTicks, 1U);
accessTicks = min(accessTicks, 0x1fU);
accessTime = accessTicks * IDE_SYSCLK_NS;
recTicks = SYSCLK_TICKS(recTime);
recTicks = max(recTicks, 1U);
recTicks = min(recTicks, 0x1fU);
*timings = ((*timings) & ~TR_33_MDMA_MASK) |
(accessTicks << TR_33_MDMA_ACCESS_SHIFT) |
(recTicks << TR_33_MDMA_RECOVERY_SHIFT);
break;
default: {
/* 33Mhz cell on others */
int halfTick = 0;
int origAccessTime = accessTime;
int origRecTime = recTime;
accessTicks = SYSCLK_TICKS(accessTime);
accessTicks = max(accessTicks, 1U);
accessTicks = min(accessTicks, 0x1fU);
accessTime = accessTicks * IDE_SYSCLK_NS;
recTicks = SYSCLK_TICKS(recTime);
recTicks = max(recTicks, 2U) - 1;
recTicks = min(recTicks, 0x1fU);
recTime = (recTicks + 1) * IDE_SYSCLK_NS;
if ((accessTicks > 1) &&
((accessTime - IDE_SYSCLK_NS/2) >= origAccessTime) &&
((recTime - IDE_SYSCLK_NS/2) >= origRecTime)) {
halfTick = 1;
accessTicks--;
}
*timings = ((*timings) & ~TR_33_MDMA_MASK) |
(accessTicks << TR_33_MDMA_ACCESS_SHIFT) |
(recTicks << TR_33_MDMA_RECOVERY_SHIFT);
if (halfTick)
*timings |= TR_33_MDMA_HALFTICK;
}
}
#ifdef IDE_PMAC_DEBUG
printk(KERN_ERR "%s: Set MDMA timing for mode %d, reg: 0x%08x\n",
drive->name, speed & 0xf, *timings);
#endif
return 0;
}
#endif /* #ifdef CONFIG_BLK_DEV_IDEDMA_PMAC */
/*
* Speedproc. This function is called by the core to set any of the standard
* timing (PIO, MDMA or UDMA) to both the drive and the controller.
* You may notice we don't use this function on normal "dma check" operation,
* our dedicated function is more precise as it uses the drive provided
* cycle time value. We should probably fix this one to deal with that too...
*/
static int __pmac
pmac_ide_tune_chipset (ide_drive_t *drive, byte speed)
{
int unit = (drive->select.b.unit & 0x01);
int ret = 0;
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
u32 *timings, *timings2;
if (pmif == NULL)
return 1;
timings = &pmif->timings[unit];
timings2 = &pmif->timings[unit+2];
switch(speed) {
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
case XFER_UDMA_6:
if (pmif->kind != controller_sh_ata6)
return 1;
case XFER_UDMA_5:
if (pmif->kind != controller_un_ata6 &&
pmif->kind != controller_k2_ata6 &&
pmif->kind != controller_sh_ata6)
return 1;
case XFER_UDMA_4:
case XFER_UDMA_3:
if (HWIF(drive)->udma_four == 0)
return 1;
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
if (pmif->kind == controller_kl_ata4)
ret = set_timings_udma_ata4(timings, speed);
else if (pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6)
ret = set_timings_udma_ata6(timings, timings2, speed);
else if (pmif->kind == controller_sh_ata6)
ret = set_timings_udma_shasta(timings, timings2, speed);
else
ret = 1;
break;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
ret = set_timings_mdma(drive, pmif->kind, timings, timings2, speed, 0);
break;
case XFER_SW_DMA_2:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
return 1;
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
pmac_ide_tuneproc(drive, speed & 0x07);
break;
default:
ret = 1;
}
if (ret)
return ret;
ret = pmac_ide_do_setfeature(drive, speed);
if (ret)
return ret;
pmac_ide_do_update_timings(drive);
drive->current_speed = speed;
return 0;
}
/*
* Blast some well known "safe" values to the timing registers at init or
* wakeup from sleep time, before we do real calculation
*/
static void __pmac
sanitize_timings(pmac_ide_hwif_t *pmif)
{
unsigned int value, value2 = 0;
switch(pmif->kind) {
case controller_sh_ata6:
value = 0x0a820c97;
value2 = 0x00033031;
break;
case controller_un_ata6:
case controller_k2_ata6:
value = 0x08618a92;
value2 = 0x00002921;
break;
case controller_kl_ata4:
value = 0x0008438c;
break;
case controller_kl_ata3:
value = 0x00084526;
break;
case controller_heathrow:
case controller_ohare:
default:
value = 0x00074526;
break;
}
pmif->timings[0] = pmif->timings[1] = value;
pmif->timings[2] = pmif->timings[3] = value2;
}
unsigned long __pmac
pmac_ide_get_base(int index)
{
return pmac_ide[index].regbase;
}
int __pmac
pmac_ide_check_base(unsigned long base)
{
int ix;
for (ix = 0; ix < MAX_HWIFS; ++ix)
if (base == pmac_ide[ix].regbase)
return ix;
return -1;
}
int __pmac
pmac_ide_get_irq(unsigned long base)
{
int ix;
for (ix = 0; ix < MAX_HWIFS; ++ix)
if (base == pmac_ide[ix].regbase)
return pmac_ide[ix].irq;
return 0;
}
static int ide_majors[] __pmacdata = { 3, 22, 33, 34, 56, 57 };
dev_t __init
pmac_find_ide_boot(char *bootdevice, int n)
{
int i;
/*
* Look through the list of IDE interfaces for this one.
*/
for (i = 0; i < pmac_ide_count; ++i) {
char *name;
if (!pmac_ide[i].node || !pmac_ide[i].node->full_name)
continue;
name = pmac_ide[i].node->full_name;
if (memcmp(name, bootdevice, n) == 0 && name[n] == 0) {
/* XXX should cope with the 2nd drive as well... */
return MKDEV(ide_majors[i], 0);
}
}
return 0;
}
/* Suspend call back, should be called after the child devices
* have actually been suspended
*/
static int
pmac_ide_do_suspend(ide_hwif_t *hwif)
{
pmac_ide_hwif_t *pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
/* We clear the timings */
pmif->timings[0] = 0;
pmif->timings[1] = 0;
#ifdef CONFIG_BLK_DEV_IDE_PMAC_BLINK
/* Note: This code will be called for every hwif, thus we'll
* try several time to stop the LED blinker timer, but that
* should be harmless
*/
if (pmu_ide_blink_enabled) {
unsigned long flags;
/* Make sure we don't hit the PMU blink */
spin_lock_irqsave(&pmu_blink_lock, flags);
if (pmu_blink_ledstate)
del_timer(&pmu_blink_timer);
pmu_blink_ledstate = 0;
spin_unlock_irqrestore(&pmu_blink_lock, flags);
}
#endif /* CONFIG_BLK_DEV_IDE_PMAC_BLINK */
disable_irq(pmif->irq);
/* The media bay will handle itself just fine */
if (pmif->mediabay)
return 0;
/* Kauai has bus control FCRs directly here */
if (pmif->kauai_fcr) {
u32 fcr = readl(pmif->kauai_fcr);
fcr &= ~(KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE);
writel(fcr, pmif->kauai_fcr);
}
/* Disable the bus on older machines and the cell on kauai */
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, pmif->node, pmif->aapl_bus_id,
0);
return 0;
}
/* Resume call back, should be called before the child devices
* are resumed
*/
static int
pmac_ide_do_resume(ide_hwif_t *hwif)
{
pmac_ide_hwif_t *pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
/* Hard reset & re-enable controller (do we really need to reset ? -BenH) */
if (!pmif->mediabay) {
ppc_md.feature_call(PMAC_FTR_IDE_RESET, pmif->node, pmif->aapl_bus_id, 1);
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, pmif->node, pmif->aapl_bus_id, 1);
msleep(10);
ppc_md.feature_call(PMAC_FTR_IDE_RESET, pmif->node, pmif->aapl_bus_id, 0);
/* Kauai has it different */
if (pmif->kauai_fcr) {
u32 fcr = readl(pmif->kauai_fcr);
fcr |= KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE;
writel(fcr, pmif->kauai_fcr);
}
msleep(jiffies_to_msecs(IDE_WAKEUP_DELAY));
}
/* Sanitize drive timings */
sanitize_timings(pmif);
enable_irq(pmif->irq);
return 0;
}
/*
* Setup, register & probe an IDE channel driven by this driver, this is
* called by one of the 2 probe functions (macio or PCI). Note that a channel
* that ends up beeing free of any device is not kept around by this driver
* (it is kept in 2.4). This introduce an interface numbering change on some
* rare machines unfortunately, but it's better this way.
*/
static int
pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
{
struct device_node *np = pmif->node;
int *bidp, i;
pmif->cable_80 = 0;
pmif->broken_dma = pmif->broken_dma_warn = 0;
if (device_is_compatible(np, "shasta-ata"))
pmif->kind = controller_sh_ata6;
else if (device_is_compatible(np, "kauai-ata"))
pmif->kind = controller_un_ata6;
else if (device_is_compatible(np, "K2-UATA"))
pmif->kind = controller_k2_ata6;
else if (device_is_compatible(np, "keylargo-ata")) {
if (strcmp(np->name, "ata-4") == 0)
pmif->kind = controller_kl_ata4;
else
pmif->kind = controller_kl_ata3;
} else if (device_is_compatible(np, "heathrow-ata"))
pmif->kind = controller_heathrow;
else {
pmif->kind = controller_ohare;
pmif->broken_dma = 1;
}
bidp = (int *)get_property(np, "AAPL,bus-id", NULL);
pmif->aapl_bus_id = bidp ? *bidp : 0;
/* Get cable type from device-tree */
if (pmif->kind == controller_kl_ata4 || pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6
|| pmif->kind == controller_sh_ata6) {
char* cable = get_property(np, "cable-type", NULL);
if (cable && !strncmp(cable, "80-", 3))
pmif->cable_80 = 1;
}
/* G5's seem to have incorrect cable type in device-tree. Let's assume
* they have a 80 conductor cable, this seem to be always the case unless
* the user mucked around
*/
if (device_is_compatible(np, "K2-UATA") ||
device_is_compatible(np, "shasta-ata"))
pmif->cable_80 = 1;
/* On Kauai-type controllers, we make sure the FCR is correct */
if (pmif->kauai_fcr)
writel(KAUAI_FCR_UATA_MAGIC |
KAUAI_FCR_UATA_RESET_N |
KAUAI_FCR_UATA_ENABLE, pmif->kauai_fcr);
pmif->mediabay = 0;
/* Make sure we have sane timings */
sanitize_timings(pmif);
#ifndef CONFIG_PPC64
/* XXX FIXME: Media bay stuff need re-organizing */
if (np->parent && np->parent->name
&& strcasecmp(np->parent->name, "media-bay") == 0) {
#ifdef CONFIG_PMAC_MEDIABAY
media_bay_set_ide_infos(np->parent, pmif->regbase, pmif->irq, hwif->index);
#endif /* CONFIG_PMAC_MEDIABAY */
pmif->mediabay = 1;
if (!bidp)
pmif->aapl_bus_id = 1;
} else if (pmif->kind == controller_ohare) {
/* The code below is having trouble on some ohare machines
* (timing related ?). Until I can put my hand on one of these
* units, I keep the old way
*/
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, np, 0, 1);
} else
#endif
{
/* This is necessary to enable IDE when net-booting */
ppc_md.feature_call(PMAC_FTR_IDE_RESET, np, pmif->aapl_bus_id, 1);
ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, np, pmif->aapl_bus_id, 1);
msleep(10);
ppc_md.feature_call(PMAC_FTR_IDE_RESET, np, pmif->aapl_bus_id, 0);
msleep(jiffies_to_msecs(IDE_WAKEUP_DELAY));
}
/* Setup MMIO ops */
default_hwif_mmiops(hwif);
hwif->OUTBSYNC = pmac_outbsync;
/* Tell common code _not_ to mess with resources */
hwif->mmio = 2;
hwif->hwif_data = pmif;
pmac_ide_init_hwif_ports(&hwif->hw, pmif->regbase, 0, &hwif->irq);
memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->io_ports));
hwif->chipset = ide_pmac;
hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET] || pmif->mediabay;
hwif->hold = pmif->mediabay;
hwif->udma_four = pmif->cable_80;
hwif->drives[0].unmask = 1;
hwif->drives[1].unmask = 1;
hwif->tuneproc = pmac_ide_tuneproc;
if (pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6
|| pmif->kind == controller_sh_ata6)
hwif->selectproc = pmac_ide_kauai_selectproc;
else
hwif->selectproc = pmac_ide_selectproc;
hwif->speedproc = pmac_ide_tune_chipset;
#ifdef CONFIG_BLK_DEV_IDE_PMAC_BLINK
pmu_ide_blink_enabled = pmu_hd_blink_init();
if (pmu_ide_blink_enabled)
hwif->led_act = pmu_hd_kick_blink;
#endif
printk(KERN_INFO "ide%d: Found Apple %s controller, bus ID %d%s, irq %d\n",
hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
pmif->mediabay ? " (mediabay)" : "", hwif->irq);
#ifdef CONFIG_PMAC_MEDIABAY
if (pmif->mediabay && check_media_bay_by_base(pmif->regbase, MB_CD) == 0)
hwif->noprobe = 0;
#endif /* CONFIG_PMAC_MEDIABAY */
hwif->sg_max_nents = MAX_DCMDS;
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/* has a DBDMA controller channel */
if (pmif->dma_regs)
pmac_ide_setup_dma(pmif, hwif);
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
/* We probe the hwif now */
probe_hwif_init(hwif);
/* The code IDE code will have set hwif->present if we have devices attached,
* if we don't, the discard the interface except if we are on a media bay slot
*/
if (!hwif->present && !pmif->mediabay) {
printk(KERN_INFO "ide%d: Bus empty, interface released.\n",
hwif->index);
default_hwif_iops(hwif);
for (i = IDE_DATA_OFFSET; i <= IDE_CONTROL_OFFSET; ++i)
hwif->io_ports[i] = 0;
hwif->chipset = ide_unknown;
hwif->noprobe = 1;
return -ENODEV;
}
return 0;
}
/*
* Attach to a macio probed interface
*/
static int __devinit
pmac_ide_macio_attach(struct macio_dev *mdev, const struct of_device_id *match)
{
void __iomem *base;
unsigned long regbase;
int irq;
ide_hwif_t *hwif;
pmac_ide_hwif_t *pmif;
int i, rc;
i = 0;
while (i < MAX_HWIFS && (ide_hwifs[i].io_ports[IDE_DATA_OFFSET] != 0
|| pmac_ide[i].node != NULL))
++i;
if (i >= MAX_HWIFS) {
printk(KERN_ERR "ide-pmac: MacIO interface attach with no slot\n");
printk(KERN_ERR " %s\n", mdev->ofdev.node->full_name);
return -ENODEV;
}
pmif = &pmac_ide[i];
hwif = &ide_hwifs[i];
if (mdev->ofdev.node->n_addrs == 0) {
printk(KERN_WARNING "ide%d: no address for %s\n",
i, mdev->ofdev.node->full_name);
return -ENXIO;
}
/* Request memory resource for IO ports */
if (macio_request_resource(mdev, 0, "ide-pmac (ports)")) {
printk(KERN_ERR "ide%d: can't request mmio resource !\n", i);
return -EBUSY;
}
/* XXX This is bogus. Should be fixed in the registry by checking
* the kind of host interrupt controller, a bit like gatwick
* fixes in irq.c. That works well enough for the single case
* where that happens though...
*/
if (macio_irq_count(mdev) == 0) {
printk(KERN_WARNING "ide%d: no intrs for device %s, using 13\n",
i, mdev->ofdev.node->full_name);
irq = 13;
} else
irq = macio_irq(mdev, 0);
base = ioremap(macio_resource_start(mdev, 0), 0x400);
regbase = (unsigned long) base;
hwif->pci_dev = mdev->bus->pdev;
hwif->gendev.parent = &mdev->ofdev.dev;
pmif->mdev = mdev;
pmif->node = mdev->ofdev.node;
pmif->regbase = regbase;
pmif->irq = irq;
pmif->kauai_fcr = NULL;
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
if (macio_resource_count(mdev) >= 2) {
if (macio_request_resource(mdev, 1, "ide-pmac (dma)"))
printk(KERN_WARNING "ide%d: can't request DMA resource !\n", i);
else
pmif->dma_regs = ioremap(macio_resource_start(mdev, 1), 0x1000);
} else
pmif->dma_regs = NULL;
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
dev_set_drvdata(&mdev->ofdev.dev, hwif);
rc = pmac_ide_setup_device(pmif, hwif);
if (rc != 0) {
/* The inteface is released to the common IDE layer */
dev_set_drvdata(&mdev->ofdev.dev, NULL);
iounmap(base);
if (pmif->dma_regs)
iounmap(pmif->dma_regs);
memset(pmif, 0, sizeof(*pmif));
macio_release_resource(mdev, 0);
if (pmif->dma_regs)
macio_release_resource(mdev, 1);
}
return rc;
}
static int
pmac_ide_macio_suspend(struct macio_dev *mdev, u32 state)
{
ide_hwif_t *hwif = (ide_hwif_t *)dev_get_drvdata(&mdev->ofdev.dev);
int rc = 0;
if (state != mdev->ofdev.dev.power.power_state && state >= 2) {
rc = pmac_ide_do_suspend(hwif);
if (rc == 0)
mdev->ofdev.dev.power.power_state = state;
}
return rc;
}
static int
pmac_ide_macio_resume(struct macio_dev *mdev)
{
ide_hwif_t *hwif = (ide_hwif_t *)dev_get_drvdata(&mdev->ofdev.dev);
int rc = 0;
if (mdev->ofdev.dev.power.power_state != 0) {
rc = pmac_ide_do_resume(hwif);
if (rc == 0)
mdev->ofdev.dev.power.power_state = 0;
}
return rc;
}
/*
* Attach to a PCI probed interface
*/
static int __devinit
pmac_ide_pci_attach(struct pci_dev *pdev, const struct pci_device_id *id)
{
ide_hwif_t *hwif;
struct device_node *np;
pmac_ide_hwif_t *pmif;
void __iomem *base;
unsigned long rbase, rlen;
int i, rc;
np = pci_device_to_OF_node(pdev);
if (np == NULL) {
printk(KERN_ERR "ide-pmac: cannot find MacIO node for Kauai ATA interface\n");
return -ENODEV;
}
i = 0;
while (i < MAX_HWIFS && (ide_hwifs[i].io_ports[IDE_DATA_OFFSET] != 0
|| pmac_ide[i].node != NULL))
++i;
if (i >= MAX_HWIFS) {
printk(KERN_ERR "ide-pmac: PCI interface attach with no slot\n");
printk(KERN_ERR " %s\n", np->full_name);
return -ENODEV;
}
pmif = &pmac_ide[i];
hwif = &ide_hwifs[i];
if (pci_enable_device(pdev)) {
printk(KERN_WARNING "ide%i: Can't enable PCI device for %s\n",
i, np->full_name);
return -ENXIO;
}
pci_set_master(pdev);
if (pci_request_regions(pdev, "Kauai ATA")) {
printk(KERN_ERR "ide%d: Cannot obtain PCI resources for %s\n",
i, np->full_name);
return -ENXIO;
}
hwif->pci_dev = pdev;
hwif->gendev.parent = &pdev->dev;
pmif->mdev = NULL;
pmif->node = np;
rbase = pci_resource_start(pdev, 0);
rlen = pci_resource_len(pdev, 0);
base = ioremap(rbase, rlen);
pmif->regbase = (unsigned long) base + 0x2000;
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
pmif->dma_regs = base + 0x1000;
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
pmif->kauai_fcr = base;
pmif->irq = pdev->irq;
pci_set_drvdata(pdev, hwif);
rc = pmac_ide_setup_device(pmif, hwif);
if (rc != 0) {
/* The inteface is released to the common IDE layer */
pci_set_drvdata(pdev, NULL);
iounmap(base);
memset(pmif, 0, sizeof(*pmif));
pci_release_regions(pdev);
}
return rc;
}
static int
pmac_ide_pci_suspend(struct pci_dev *pdev, u32 state)
{
ide_hwif_t *hwif = (ide_hwif_t *)pci_get_drvdata(pdev);
int rc = 0;
if (state != pdev->dev.power.power_state && state >= 2) {
rc = pmac_ide_do_suspend(hwif);
if (rc == 0)
pdev->dev.power.power_state = state;
}
return rc;
}
static int
pmac_ide_pci_resume(struct pci_dev *pdev)
{
ide_hwif_t *hwif = (ide_hwif_t *)pci_get_drvdata(pdev);
int rc = 0;
if (pdev->dev.power.power_state != 0) {
rc = pmac_ide_do_resume(hwif);
if (rc == 0)
pdev->dev.power.power_state = 0;
}
return rc;
}
static struct of_device_id pmac_ide_macio_match[] =
{
{
.name = "IDE",
},
{
.name = "ATA",
},
{
.type = "ide",
},
{
.type = "ata",
},
{},
};
static struct macio_driver pmac_ide_macio_driver =
{
.name = "ide-pmac",
.match_table = pmac_ide_macio_match,
.probe = pmac_ide_macio_attach,
.suspend = pmac_ide_macio_suspend,
.resume = pmac_ide_macio_resume,
};
static struct pci_device_id pmac_ide_pci_match[] = {
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_SH_ATA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
};
static struct pci_driver pmac_ide_pci_driver = {
.name = "ide-pmac",
.id_table = pmac_ide_pci_match,
.probe = pmac_ide_pci_attach,
.suspend = pmac_ide_pci_suspend,
.resume = pmac_ide_pci_resume,
};
MODULE_DEVICE_TABLE(pci, pmac_ide_pci_match);
void __init
pmac_ide_probe(void)
{
if (_machine != _MACH_Pmac)
return;
#ifdef CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST
pci_register_driver(&pmac_ide_pci_driver);
macio_register_driver(&pmac_ide_macio_driver);
#else
macio_register_driver(&pmac_ide_macio_driver);
pci_register_driver(&pmac_ide_pci_driver);
#endif
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/*
* pmac_ide_build_dmatable builds the DBDMA command list
* for a transfer and sets the DBDMA channel to point to it.
*/
static int __pmac
pmac_ide_build_dmatable(ide_drive_t *drive, struct request *rq)
{
struct dbdma_cmd *table;
int i, count = 0;
ide_hwif_t *hwif = HWIF(drive);
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
volatile struct dbdma_regs __iomem *dma = pmif->dma_regs;
struct scatterlist *sg;
int wr = (rq_data_dir(rq) == WRITE);
/* DMA table is already aligned */
table = (struct dbdma_cmd *) pmif->dma_table_cpu;
/* Make sure DMA controller is stopped (necessary ?) */
writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma->control);
while (readl(&dma->status) & RUN)
udelay(1);
hwif->sg_nents = i = ide_build_sglist(drive, rq);
if (!i)
return 0;
/* Build DBDMA commands list */
sg = hwif->sg_table;
while (i && sg_dma_len(sg)) {
u32 cur_addr;
u32 cur_len;
cur_addr = sg_dma_address(sg);
cur_len = sg_dma_len(sg);
if (pmif->broken_dma && cur_addr & (L1_CACHE_BYTES - 1)) {
if (pmif->broken_dma_warn == 0) {
printk(KERN_WARNING "%s: DMA on non aligned address,"
"switching to PIO on Ohare chipset\n", drive->name);
pmif->broken_dma_warn = 1;
}
goto use_pio_instead;
}
while (cur_len) {
unsigned int tc = (cur_len < 0xfe00)? cur_len: 0xfe00;
if (count++ >= MAX_DCMDS) {
printk(KERN_WARNING "%s: DMA table too small\n",
drive->name);
goto use_pio_instead;
}
st_le16(&table->command, wr? OUTPUT_MORE: INPUT_MORE);
st_le16(&table->req_count, tc);
st_le32(&table->phy_addr, cur_addr);
table->cmd_dep = 0;
table->xfer_status = 0;
table->res_count = 0;
cur_addr += tc;
cur_len -= tc;
++table;
}
sg++;
i--;
}
/* convert the last command to an input/output last command */
if (count) {
st_le16(&table[-1].command, wr? OUTPUT_LAST: INPUT_LAST);
/* add the stop command to the end of the list */
memset(table, 0, sizeof(struct dbdma_cmd));
st_le16(&table->command, DBDMA_STOP);
mb();
writel(hwif->dmatable_dma, &dma->cmdptr);
return 1;
}
printk(KERN_DEBUG "%s: empty DMA table?\n", drive->name);
use_pio_instead:
pci_unmap_sg(hwif->pci_dev,
hwif->sg_table,
hwif->sg_nents,
hwif->sg_dma_direction);
return 0; /* revert to PIO for this request */
}
/* Teardown mappings after DMA has completed. */
static void __pmac
pmac_ide_destroy_dmatable (ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = HWIF(drive)->pci_dev;
struct scatterlist *sg = hwif->sg_table;
int nents = hwif->sg_nents;
if (nents) {
pci_unmap_sg(dev, sg, nents, hwif->sg_dma_direction);
hwif->sg_nents = 0;
}
}
/*
* Pick up best MDMA timing for the drive and apply it
*/
static int __pmac
pmac_ide_mdma_enable(ide_drive_t *drive, u16 mode)
{
ide_hwif_t *hwif = HWIF(drive);
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
int drive_cycle_time;
struct hd_driveid *id = drive->id;
u32 *timings, *timings2;
u32 timing_local[2];
int ret;
/* which drive is it ? */
timings = &pmif->timings[drive->select.b.unit & 0x01];
timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
/* Check if drive provide explicit cycle time */
if ((id->field_valid & 2) && (id->eide_dma_time))
drive_cycle_time = id->eide_dma_time;
else
drive_cycle_time = 0;
/* Copy timings to local image */
timing_local[0] = *timings;
timing_local[1] = *timings2;
/* Calculate controller timings */
ret = set_timings_mdma( drive, pmif->kind,
&timing_local[0],
&timing_local[1],
mode,
drive_cycle_time);
if (ret)
return 0;
/* Set feature on drive */
printk(KERN_INFO "%s: Enabling MultiWord DMA %d\n", drive->name, mode & 0xf);
ret = pmac_ide_do_setfeature(drive, mode);
if (ret) {
printk(KERN_WARNING "%s: Failed !\n", drive->name);
return 0;
}
/* Apply timings to controller */
*timings = timing_local[0];
*timings2 = timing_local[1];
/* Set speed info in drive */
drive->current_speed = mode;
if (!drive->init_speed)
drive->init_speed = mode;
return 1;
}
/*
* Pick up best UDMA timing for the drive and apply it
*/
static int __pmac
pmac_ide_udma_enable(ide_drive_t *drive, u16 mode)
{
ide_hwif_t *hwif = HWIF(drive);
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
u32 *timings, *timings2;
u32 timing_local[2];
int ret;
/* which drive is it ? */
timings = &pmif->timings[drive->select.b.unit & 0x01];
timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
/* Copy timings to local image */
timing_local[0] = *timings;
timing_local[1] = *timings2;
/* Calculate timings for interface */
if (pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6)
ret = set_timings_udma_ata6( &timing_local[0],
&timing_local[1],
mode);
else if (pmif->kind == controller_sh_ata6)
ret = set_timings_udma_shasta( &timing_local[0],
&timing_local[1],
mode);
else
ret = set_timings_udma_ata4(&timing_local[0], mode);
if (ret)
return 0;
/* Set feature on drive */
printk(KERN_INFO "%s: Enabling Ultra DMA %d\n", drive->name, mode & 0x0f);
ret = pmac_ide_do_setfeature(drive, mode);
if (ret) {
printk(KERN_WARNING "%s: Failed !\n", drive->name);
return 0;
}
/* Apply timings to controller */
*timings = timing_local[0];
*timings2 = timing_local[1];
/* Set speed info in drive */
drive->current_speed = mode;
if (!drive->init_speed)
drive->init_speed = mode;
return 1;
}
/*
* Check what is the best DMA timing setting for the drive and
* call appropriate functions to apply it.
*/
static int __pmac
pmac_ide_dma_check(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
int enable = 1;
int map;
drive->using_dma = 0;
if (drive->media == ide_floppy)
enable = 0;
if (((id->capability & 1) == 0) && !__ide_dma_good_drive(drive))
enable = 0;
if (__ide_dma_bad_drive(drive))
enable = 0;
if (enable) {
short mode;
map = XFER_MWDMA;
if (pmif->kind == controller_kl_ata4
|| pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6
|| pmif->kind == controller_sh_ata6) {
map |= XFER_UDMA;
if (pmif->cable_80) {
map |= XFER_UDMA_66;
if (pmif->kind == controller_un_ata6 ||
pmif->kind == controller_k2_ata6 ||
pmif->kind == controller_sh_ata6)
map |= XFER_UDMA_100;
if (pmif->kind == controller_sh_ata6)
map |= XFER_UDMA_133;
}
}
mode = ide_find_best_mode(drive, map);
if (mode & XFER_UDMA)
drive->using_dma = pmac_ide_udma_enable(drive, mode);
else if (mode & XFER_MWDMA)
drive->using_dma = pmac_ide_mdma_enable(drive, mode);
hwif->OUTB(0, IDE_CONTROL_REG);
/* Apply settings to controller */
pmac_ide_do_update_timings(drive);
}
return 0;
}
/*
* Prepare a DMA transfer. We build the DMA table, adjust the timings for
* a read on KeyLargo ATA/66 and mark us as waiting for DMA completion
*/
static int __pmac
pmac_ide_dma_setup(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
struct request *rq = HWGROUP(drive)->rq;
u8 unit = (drive->select.b.unit & 0x01);
u8 ata4;
if (pmif == NULL)
return 1;
ata4 = (pmif->kind == controller_kl_ata4);
if (!pmac_ide_build_dmatable(drive, rq)) {
ide_map_sg(drive, rq);
return 1;
}
/* Apple adds 60ns to wrDataSetup on reads */
if (ata4 && (pmif->timings[unit] & TR_66_UDMA_EN)) {
writel(pmif->timings[unit] + (!rq_data_dir(rq) ? 0x00800000UL : 0),
PMAC_IDE_REG(IDE_TIMING_CONFIG));
(void)readl(PMAC_IDE_REG(IDE_TIMING_CONFIG));
}
drive->waiting_for_dma = 1;
return 0;
}
static void __pmac
pmac_ide_dma_exec_cmd(ide_drive_t *drive, u8 command)
{
/* issue cmd to drive */
ide_execute_command(drive, command, &ide_dma_intr, 2*WAIT_CMD, NULL);
}
/*
* Kick the DMA controller into life after the DMA command has been issued
* to the drive.
*/
static void __pmac
pmac_ide_dma_start(ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
volatile struct dbdma_regs __iomem *dma;
dma = pmif->dma_regs;
writel((RUN << 16) | RUN, &dma->control);
/* Make sure it gets to the controller right now */
(void)readl(&dma->control);
}
/*
* After a DMA transfer, make sure the controller is stopped
*/
static int __pmac
pmac_ide_dma_end (ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
volatile struct dbdma_regs __iomem *dma;
u32 dstat;
if (pmif == NULL)
return 0;
dma = pmif->dma_regs;
drive->waiting_for_dma = 0;
dstat = readl(&dma->status);
writel(((RUN|WAKE|DEAD) << 16), &dma->control);
pmac_ide_destroy_dmatable(drive);
/* verify good dma status. we don't check for ACTIVE beeing 0. We should...
* in theory, but with ATAPI decices doing buffer underruns, that would
* cause us to disable DMA, which isn't what we want
*/
return (dstat & (RUN|DEAD)) != RUN;
}
/*
* Check out that the interrupt we got was for us. We can't always know this
* for sure with those Apple interfaces (well, we could on the recent ones but
* that's not implemented yet), on the other hand, we don't have shared interrupts
* so it's not really a problem
*/
static int __pmac
pmac_ide_dma_test_irq (ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
volatile struct dbdma_regs __iomem *dma;
unsigned long status, timeout;
if (pmif == NULL)
return 0;
dma = pmif->dma_regs;
/* We have to things to deal with here:
*
* - The dbdma won't stop if the command was started
* but completed with an error without transferring all
* datas. This happens when bad blocks are met during
* a multi-block transfer.
*
* - The dbdma fifo hasn't yet finished flushing to
* to system memory when the disk interrupt occurs.
*
*/
/* If ACTIVE is cleared, the STOP command have passed and
* transfer is complete.
*/
status = readl(&dma->status);
if (!(status & ACTIVE))
return 1;
if (!drive->waiting_for_dma)
printk(KERN_WARNING "ide%d, ide_dma_test_irq \
called while not waiting\n", HWIF(drive)->index);
/* If dbdma didn't execute the STOP command yet, the
* active bit is still set. We consider that we aren't
* sharing interrupts (which is hopefully the case with
* those controllers) and so we just try to flush the
* channel for pending data in the fifo
*/
udelay(1);
writel((FLUSH << 16) | FLUSH, &dma->control);
timeout = 0;
for (;;) {
udelay(1);
status = readl(&dma->status);
if ((status & FLUSH) == 0)
break;
if (++timeout > 100) {
printk(KERN_WARNING "ide%d, ide_dma_test_irq \
timeout flushing channel\n", HWIF(drive)->index);
break;
}
}
return 1;
}
static int __pmac
pmac_ide_dma_host_off (ide_drive_t *drive)
{
return 0;
}
static int __pmac
pmac_ide_dma_host_on (ide_drive_t *drive)
{
return 0;
}
static int __pmac
pmac_ide_dma_lostirq (ide_drive_t *drive)
{
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
volatile struct dbdma_regs __iomem *dma;
unsigned long status;
if (pmif == NULL)
return 0;
dma = pmif->dma_regs;
status = readl(&dma->status);
printk(KERN_ERR "ide-pmac lost interrupt, dma status: %lx\n", status);
return 0;
}
/*
* Allocate the data structures needed for using DMA with an interface
* and fill the proper list of functions pointers
*/
static void __init
pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
{
/* We won't need pci_dev if we switch to generic consistent
* DMA routines ...
*/
if (hwif->pci_dev == NULL)
return;
/*
* Allocate space for the DBDMA commands.
* The +2 is +1 for the stop command and +1 to allow for
* aligning the start address to a multiple of 16 bytes.
*/
pmif->dma_table_cpu = (struct dbdma_cmd*)pci_alloc_consistent(
hwif->pci_dev,
(MAX_DCMDS + 2) * sizeof(struct dbdma_cmd),
&hwif->dmatable_dma);
if (pmif->dma_table_cpu == NULL) {
printk(KERN_ERR "%s: unable to allocate DMA command list\n",
hwif->name);
return;
}
hwif->ide_dma_off_quietly = &__ide_dma_off_quietly;
hwif->ide_dma_on = &__ide_dma_on;
hwif->ide_dma_check = &pmac_ide_dma_check;
hwif->dma_setup = &pmac_ide_dma_setup;
hwif->dma_exec_cmd = &pmac_ide_dma_exec_cmd;
hwif->dma_start = &pmac_ide_dma_start;
hwif->ide_dma_end = &pmac_ide_dma_end;
hwif->ide_dma_test_irq = &pmac_ide_dma_test_irq;
hwif->ide_dma_host_off = &pmac_ide_dma_host_off;
hwif->ide_dma_host_on = &pmac_ide_dma_host_on;
hwif->ide_dma_timeout = &__ide_dma_timeout;
hwif->ide_dma_lostirq = &pmac_ide_dma_lostirq;
hwif->atapi_dma = 1;
switch(pmif->kind) {
case controller_sh_ata6:
hwif->ultra_mask = pmif->cable_80 ? 0x7f : 0x07;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x00;
break;
case controller_un_ata6:
case controller_k2_ata6:
hwif->ultra_mask = pmif->cable_80 ? 0x3f : 0x07;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x00;
break;
case controller_kl_ata4:
hwif->ultra_mask = pmif->cable_80 ? 0x1f : 0x07;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x00;
break;
default:
hwif->ultra_mask = 0x00;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x00;
break;
}
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
