/*
* SL82C105/Winbond 553 IDE driver
*
* Maintainer unknown.
*
* Drive tuning added from Rebel.com's kernel sources
* -- Russell King (15/11/98) linux@arm.linux.org.uk
*
* Merge in Russell's HW workarounds, fix various problems
* with the timing registers setup.
* -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
*
* Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*/
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/hdreg.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <asm/io.h>
#undef DEBUG
#ifdef DEBUG
#define DBG(arg) printk arg
#else
#define DBG(fmt,...)
#endif
/*
* SL82C105 PCI config register 0x40 bits.
*/
#define CTRL_IDE_IRQB (1 << 30)
#define CTRL_IDE_IRQA (1 << 28)
#define CTRL_LEGIRQ (1 << 11)
#define CTRL_P1F16 (1 << 5)
#define CTRL_P1EN (1 << 4)
#define CTRL_P0F16 (1 << 1)
#define CTRL_P0EN (1 << 0)
/*
* Convert a PIO mode and cycle time to the required on/off times
* for the interface. This has protection against runaway timings.
*/
static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio)
{
unsigned int cmd_on, cmd_off;
u8 iordy = 0;
cmd_on = (ide_pio_timings[pio].active_time + 29) / 30;
cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30;
if (cmd_on == 0)
cmd_on = 1;
if (cmd_off == 0)
cmd_off = 1;
if (pio > 2 || ide_dev_has_iordy(drive->id))
iordy = 0x40;
return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy;
}
/*
* Configure the chipset for PIO mode.
*/
static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
int reg = 0x44 + drive->dn * 4;
u16 drv_ctrl;
drv_ctrl = get_pio_timings(drive, pio);
/*
* Store the PIO timings so that we can restore them
* in case DMA will be turned off...
*/
drive->drive_data &= 0xffff0000;
drive->drive_data |= drv_ctrl;
pci_write_config_word(dev, reg, drv_ctrl);
pci_read_config_word (dev, reg, &drv_ctrl);
printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
ide_xfer_verbose(pio + XFER_PIO_0),
ide_pio_cycle_time(drive, pio), drv_ctrl);
}
/*
* Configure the chipset for DMA mode.
*/
static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
u16 drv_ctrl;
DBG(("sl82c105_tune_chipset(drive:%s, speed:%s)\n",
drive->name, ide_xfer_verbose(speed)));
drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
/*
* Store the DMA timings so that we can actually program
* them when DMA will be turned on...
*/
drive->drive_data &= 0x0000ffff;
drive->drive_data |= (unsigned long)drv_ctrl << 16;
}
/*
* The SL82C105 holds off all IDE interrupts while in DMA mode until
* all DMA activity is completed. Sometimes this causes problems (eg,
* when the drive wants to report an error condition).
*
* 0x7e is a "chip testing" register. Bit 2 resets the DMA controller
* state machine. We need to kick this to work around various bugs.
*/
static inline void sl82c105_reset_host(struct pci_dev *dev)
{
u16 val;
pci_read_config_word(dev, 0x7e, &val);
pci_write_config_word(dev, 0x7e, val | (1 << 2));
pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
}
/*
* If we get an IRQ timeout, it might be that the DMA state machine
* got confused. Fix from Todd Inglett. Details from Winbond.
*
* This function is called when the IDE timer expires, the drive
* indicates that it is READY, and we were waiting for DMA to complete.
*/
static void sl82c105_dma_lost_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
u8 dma_cmd;
printk("sl82c105: lost IRQ, resetting host\n");
/*
* Check the raw interrupt from the drive.
*/
pci_read_config_dword(dev, 0x40, &val);
if (val & mask)
printk("sl82c105: drive was requesting IRQ, but host lost it\n");
/*
* Was DMA enabled? If so, disable it - we're resetting the
* host. The IDE layer will be handling the drive for us.
*/
dma_cmd = inb(hwif->dma_command);
if (dma_cmd & 1) {
outb(dma_cmd & ~1, hwif->dma_command);
printk("sl82c105: DMA was enabled\n");
}
sl82c105_reset_host(dev);
}
/*
* ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
* Winbond recommend that the DMA state machine is reset prior to
* setting the bus master DMA enable bit.
*
* The generic IDE core will have disabled the BMEN bit before this
* function is called.
*/
static void sl82c105_dma_start(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
int reg = 0x44 + drive->dn * 4;
DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
pci_write_config_word(dev, reg, drive->drive_data >> 16);
sl82c105_reset_host(dev);
ide_dma_start(drive);
}
static void sl82c105_dma_timeout(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
DBG(("sl82c105_dma_timeout(drive:%s)\n", drive->name));
sl82c105_reset_host(dev);
ide_dma_timeout(drive);
}
static int sl82c105_dma_end(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
int reg = 0x44 + drive->dn * 4;
int ret;
DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
ret = __ide_dma_end(drive);
pci_write_config_word(dev, reg, drive->drive_data);
return ret;
}
/*
* ATA reset will clear the 16 bits mode in the control
* register, we need to reprogram it
*/
static void sl82c105_resetproc(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
u32 val;
DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));
pci_read_config_dword(dev, 0x40, &val);
val |= (CTRL_P1F16 | CTRL_P0F16);
pci_write_config_dword(dev, 0x40, val);
}
/*
* Return the revision of the Winbond bridge
* which this function is part of.
*/
static unsigned int sl82c105_bridge_revision(struct pci_dev *dev)
{
struct pci_dev *bridge;
/*
* The bridge should be part of the same device, but function 0.
*/
bridge = pci_get_bus_and_slot(dev->bus->number,
PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
if (!bridge)
return -1;
/*
* Make sure it is a Winbond 553 and is an ISA bridge.
*/
if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
pci_dev_put(bridge);
return -1;
}
/*
* We need to find function 0's revision, not function 1
*/
pci_dev_put(bridge);
return bridge->revision;
}
/*
* Enable the PCI device
*
* --BenH: It's arch fixup code that should enable channels that
* have not been enabled by firmware. I decided we can still enable
* channel 0 here at least, but channel 1 has to be enabled by
* firmware or arch code. We still set both to 16 bits mode.
*/
static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev, const char *msg)
{
u32 val;
DBG(("init_chipset_sl82c105()\n"));
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
return dev->irq;
}
/*
* Initialise IDE channel
*/
static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned int rev;
DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
hwif->set_pio_mode = &sl82c105_set_pio_mode;
hwif->set_dma_mode = &sl82c105_set_dma_mode;
hwif->resetproc = &sl82c105_resetproc;
if (!hwif->dma_base)
return;
rev = sl82c105_bridge_revision(dev);
if (rev <= 5) {
/*
* Never ever EVER under any circumstances enable
* DMA when the bridge is this old.
*/
printk(" %s: Winbond W83C553 bridge revision %d, "
"BM-DMA disabled\n", hwif->name, rev);
return;
}
hwif->mwdma_mask = ATA_MWDMA2;
hwif->dma_lost_irq = &sl82c105_dma_lost_irq;
hwif->dma_start = &sl82c105_dma_start;
hwif->ide_dma_end = &sl82c105_dma_end;
hwif->dma_timeout = &sl82c105_dma_timeout;
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
}
static const struct ide_port_info sl82c105_chipset __devinitdata = {
.name = "W82C105",
.init_chipset = init_chipset_sl82c105,
.init_hwif = init_hwif_sl82c105,
.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
.host_flags = IDE_HFLAG_IO_32BIT |
IDE_HFLAG_UNMASK_IRQS |
IDE_HFLAG_NO_AUTODMA |
IDE_HFLAG_BOOTABLE,
.pio_mask = ATA_PIO5,
};
static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
return ide_setup_pci_device(dev, &sl82c105_chipset);
}
static const struct pci_device_id sl82c105_pci_tbl[] = {
{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
static struct pci_driver driver = {
.name = "W82C105_IDE",
.id_table = sl82c105_pci_tbl,
.probe = sl82c105_init_one,
};
static int __init sl82c105_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
module_init(sl82c105_ide_init);
MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
MODULE_LICENSE("GPL");
