/*
* Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
* Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator
*
* CYPRESS CY82C693 chipset IDE controller
*
* The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards.
* Writing the driver was quite simple, since most of the job is
* done by the generic pci-ide support.
* The hard part was finding the CY82C693's datasheet on Cypress's
* web page :-(. But Altavista solved this problem :-).
*
*
* Notes:
* - I recently got a 16.8G IBM DTTA, so I was able to test it with
* a large and fast disk - the results look great, so I'd say the
* driver is working fine :-)
* hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA
* - this is my first linux driver, so there's probably a lot of room
* for optimizations and bug fixing, so feel free to do it.
* - if using PIO mode it's a good idea to set the PIO mode and
* 32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda
* - I had some problems with my IBM DHEA with PIO modes < 2
* (lost interrupts) ?????
* - first tests with DMA look okay, they seem to work, but there is a
* problem with sound - the BusMaster IDE TimeOut should fixed this
*
* Ancient History:
* AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693
* ASK@1999-01-23: v0.33 made a few minor code clean ups
* removed DMA clock speed setting by default
* added boot message
* ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut
* added support to set DMA Controller Clock Speed
* ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes
* on some drives.
* ASK@1998-10-29: v0.3 added support to set DMA modes
* ASK@1998-10-28: v0.2 added support to set PIO modes
* ASK@1998-10-27: v0.1 first version - chipset detection
*
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
#define DRV_NAME "cy82c693"
/* the current version */
#define CY82_VERSION "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"
/*
* The following are used to debug the driver.
*/
#define CY82C693_DEBUG_LOGS 0
#define CY82C693_DEBUG_INFO 0
/* define CY82C693_SETDMA_CLOCK to set DMA Controller Clock Speed to ATCLK */
#undef CY82C693_SETDMA_CLOCK
/*
* NOTE: the value for busmaster timeout is tricky and I got it by
* trial and error! By using a to low value will cause DMA timeouts
* and drop IDE performance, and by using a to high value will cause
* audio playback to scatter.
* If you know a better value or how to calc it, please let me know.
*/
/* twice the value written in cy82c693ub datasheet */
#define BUSMASTER_TIMEOUT 0x50
/*
* the value above was tested on my machine and it seems to work okay
*/
/* here are the offset definitions for the registers */
#define CY82_IDE_CMDREG 0x04
#define CY82_IDE_ADDRSETUP 0x48
#define CY82_IDE_MASTER_IOR 0x4C
#define CY82_IDE_MASTER_IOW 0x4D
#define CY82_IDE_SLAVE_IOR 0x4E
#define CY82_IDE_SLAVE_IOW 0x4F
#define CY82_IDE_MASTER_8BIT 0x50
#define CY82_IDE_SLAVE_8BIT 0x51
#define CY82_INDEX_PORT 0x22
#define CY82_DATA_PORT 0x23
#define CY82_INDEX_CTRLREG1 0x01
#define CY82_INDEX_CHANNEL0 0x30
#define CY82_INDEX_CHANNEL1 0x31
#define CY82_INDEX_TIMEOUT 0x32
/* the min and max PCI bus speed in MHz - from datasheet */
#define CY82C963_MIN_BUS_SPEED 25
#define CY82C963_MAX_BUS_SPEED 33
/* the struct for the PIO mode timings */
typedef struct pio_clocks_s {
u8 address_time; /* Address setup (clocks) */
u8 time_16r; /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */
u8 time_16w; /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */
u8 time_8; /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */
} pio_clocks_t;
/*
* calc clocks using bus_speed
* returns (rounded up) time in bus clocks for time in ns
*/
static int calc_clk(int time, int bus_speed)
{
int clocks;
clocks = (time*bus_speed+999)/1000 - 1;
if (clocks < 0)
clocks = 0;
if (clocks > 0x0F)
clocks = 0x0F;
return clocks;
}
/*
* compute the values for the clock registers for PIO
* mode and pci_clk [MHz] speed
*
* NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used
* for mode 3 and 4 drives 8 and 16-bit timings are the same
*
*/
static void compute_clocks(u8 pio, pio_clocks_t *p_pclk)
{
struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
int clk1, clk2;
int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
/* we don't check against CY82C693's min and max speed,
* so you can play with the idebus=xx parameter
*/
/* let's calc the address setup time clocks */
p_pclk->address_time = (u8)calc_clk(t->setup, bus_speed);
/* let's calc the active and recovery time clocks */
clk1 = calc_clk(t->active, bus_speed);
/* calc recovery timing */
clk2 = t->cycle - t->active - t->setup;
clk2 = calc_clk(clk2, bus_speed);
clk1 = (clk1<<4)|clk2; /* combine active and recovery clocks */
/* note: we use the same values for 16bit IOR and IOW
* those are all the same, since I don't have other
* timings than those from ide-lib.c
*/
p_pclk->time_16r = (u8)clk1;
p_pclk->time_16w = (u8)clk1;
/* what are good values for 8bit ?? */
p_pclk->time_8 = (u8)clk1;
}
/*
* set DMA mode a specific channel for CY82C693
*/
static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
ide_hwif_t *hwif = drive->hwif;
u8 single = (mode & 0x10) >> 4, index = 0, data = 0;
index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;
#if CY82C693_DEBUG_LOGS
/* for debug let's show the previous values */
outb(index, CY82_INDEX_PORT);
data = inb(CY82_DATA_PORT);
printk(KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n",
drive->name, HWIF(drive)->channel, drive->select.b.unit,
(data&0x3), ((data>>2)&1));
#endif /* CY82C693_DEBUG_LOGS */
data = (mode & 3) | (single << 2);
outb(index, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
drive->name, HWIF(drive)->channel, drive->select.b.unit,
mode & 3, single);
#endif /* CY82C693_DEBUG_INFO */
/*
* note: below we set the value for Bus Master IDE TimeOut Register
* I'm not absolutly sure what this does, but it solved my problem
* with IDE DMA and sound, so I now can play sound and work with
* my IDE driver at the same time :-)
*
* If you know the correct (best) value for this register please
* let me know - ASK
*/
data = BUSMASTER_TIMEOUT;
outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n",
drive->name, data);
#endif /* CY82C693_DEBUG_INFO */
}
static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
pio_clocks_t pclk;
unsigned int addrCtrl;
/* select primary or secondary channel */
if (hwif->index > 0) { /* drive is on the secondary channel */
dev = pci_get_slot(dev->bus, dev->devfn+1);
if (!dev) {
printk(KERN_ERR "%s: tune_drive: "
"Cannot find secondary interface!\n",
drive->name);
return;
}
}
#if CY82C693_DEBUG_LOGS
/* for debug let's show the register values */
if (drive->select.b.unit == 0) {
/*
* get master drive registers
* address setup control register
* is 32 bit !!!
*/
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
addrCtrl &= 0x0F;
/* now let's get the remaining registers */
pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r);
pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w);
pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8);
} else {
/*
* set slave drive registers
* address setup control register
* is 32 bit !!!
*/
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
addrCtrl &= 0xF0;
addrCtrl >>= 4;
/* now let's get the remaining registers */
pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r);
pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w);
pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8);
}
printk(KERN_INFO "%s (ch=%d, dev=%d): PIO timing is "
"(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
drive->name, hwif->channel, drive->select.b.unit,
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_LOGS */
/* let's calc the values for this PIO mode */
compute_clocks(pio, &pclk);
/* now let's write the clocks registers */
if (drive->select.b.unit == 0) {
/*
* set master drive
* address setup control register
* is 32 bit !!!
*/
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
addrCtrl &= (~0xF);
addrCtrl |= (unsigned int)pclk.address_time;
pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
/* now let's set the remaining registers */
pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
addrCtrl &= 0xF;
} else {
/*
* set slave drive
* address setup control register
* is 32 bit !!!
*/
pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
addrCtrl &= (~0xF0);
addrCtrl |= ((unsigned int)pclk.address_time<<4);
pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
/* now let's set the remaining registers */
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
addrCtrl >>= 4;
addrCtrl &= 0xF;
}
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to "
"(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
drive->name, hwif->channel, drive->select.b.unit,
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_INFO */
}
/*
* this function is called during init and is used to setup the cy82c693 chip
*/
static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev)
{
if (PCI_FUNC(dev->devfn) != 1)
return 0;
#ifdef CY82C693_SETDMA_CLOCK
u8 data = 0;
#endif /* CY82C693_SETDMA_CLOCK */
/* write info about this verion of the driver */
printk(KERN_INFO CY82_VERSION "\n");
#ifdef CY82C693_SETDMA_CLOCK
/* okay let's set the DMA clock speed */
outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
data = inb(CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO DRV_NAME ": Peripheral Configuration Register: 0x%X\n",
data);
#endif /* CY82C693_DEBUG_INFO */
/*
* for some reason sometimes the DMA controller
* speed is set to ATCLK/2 ???? - we fix this here
*
* note: i don't know what causes this strange behaviour,
* but even changing the dma speed doesn't solve it :-(
* the ide performance is still only half the normal speed
*
* if anybody knows what goes wrong with my machine, please
* let me know - ASK
*/
data |= 0x03;
outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO ": New Peripheral Configuration Register: 0x%X\n",
data);
#endif /* CY82C693_DEBUG_INFO */
#endif /* CY82C693_SETDMA_CLOCK */
return 0;
}
static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
{
static ide_hwif_t *primary;
struct pci_dev *dev = to_pci_dev(hwif->dev);
if (PCI_FUNC(dev->devfn) == 1)
primary = hwif;
else {
hwif->mate = primary;
hwif->channel = 1;
}
}
static const struct ide_port_ops cy82c693_port_ops = {
.set_pio_mode = cy82c693_set_pio_mode,
.set_dma_mode = cy82c693_set_dma_mode,
};
static const struct ide_port_info cy82c693_chipset __devinitdata = {
.name = DRV_NAME,
.init_chipset = init_chipset_cy82c693,
.init_iops = init_iops_cy82c693,
.port_ops = &cy82c693_port_ops,
.chipset = ide_cy82c693,
.host_flags = IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.swdma_mask = ATA_SWDMA2,
.mwdma_mask = ATA_MWDMA2,
};
static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct pci_dev *dev2;
int ret = -ENODEV;
/* CY82C693 is more than only a IDE controller.
Function 1 is primary IDE channel, function 2 - secondary. */
if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE &&
PCI_FUNC(dev->devfn) == 1) {
dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
ret = ide_pci_init_two(dev, dev2, &cy82c693_chipset, NULL);
if (ret)
pci_dev_put(dev2);
}
return ret;
}
static void __devexit cy82c693_remove(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
ide_pci_remove(dev);
pci_dev_put(dev2);
}
static const struct pci_device_id cy82c693_pci_tbl[] = {
{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cy82c693_pci_tbl);
static struct pci_driver driver = {
.name = "Cypress_IDE",
.id_table = cy82c693_pci_tbl,
.probe = cy82c693_init_one,
.remove = __devexit_p(cy82c693_remove),
};
static int __init cy82c693_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
static void __exit cy82c693_ide_exit(void)
{
pci_unregister_driver(&driver);
}
module_init(cy82c693_ide_init);
module_exit(cy82c693_ide_exit);
MODULE_AUTHOR("Andreas Krebs, Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE");
MODULE_LICENSE("GPL");
