/*
* linux/drivers/ide/ide-floppy.c Version 0.99 Feb 24 2002
*
* Copyright (C) 1996 - 1999 Gadi Oxman <gadio@netvision.net.il>
* Copyright (C) 2000 - 2002 Paul Bristow <paul@paulbristow.net>
*/
/*
* IDE ATAPI floppy driver.
*
* The driver currently doesn't have any fancy features, just the bare
* minimum read/write support.
*
* This driver supports the following IDE floppy drives:
*
* LS-120/240 SuperDisk
* Iomega Zip 100/250
* Iomega PC Card Clik!/PocketZip
*
* Many thanks to Lode Leroy <Lode.Leroy@www.ibase.be>, who tested so many
* ALPHA patches to this driver on an EASYSTOR LS-120 ATAPI floppy drive.
*
* Ver 0.1 Oct 17 96 Initial test version, mostly based on ide-tape.c.
* Ver 0.2 Oct 31 96 Minor changes.
* Ver 0.3 Dec 2 96 Fixed error recovery bug.
* Ver 0.4 Jan 26 97 Add support for the HDIO_GETGEO ioctl.
* Ver 0.5 Feb 21 97 Add partitions support.
* Use the minimum of the LBA and CHS capacities.
* Avoid hwgroup->rq == NULL on the last irq.
* Fix potential null dereferencing with DEBUG_LOG.
* Ver 0.8 Dec 7 97 Increase irq timeout from 10 to 50 seconds.
* Add media write-protect detection.
* Issue START command only if TEST UNIT READY fails.
* Add work-around for IOMEGA ZIP revision 21.D.
* Remove idefloppy_get_capabilities().
* Ver 0.9 Jul 4 99 Fix a bug which might have caused the number of
* bytes requested on each interrupt to be zero.
* Thanks to <shanos@es.co.nz> for pointing this out.
* Ver 0.9.sv Jan 6 01 Sam Varshavchik <mrsam@courier-mta.com>
* Implement low level formatting. Reimplemented
* IDEFLOPPY_CAPABILITIES_PAGE, since we need the srfp
* bit. My LS-120 drive barfs on
* IDEFLOPPY_CAPABILITIES_PAGE, but maybe it's just me.
* Compromise by not reporting a failure to get this
* mode page. Implemented four IOCTLs in order to
* implement formatting. IOCTls begin with 0x4600,
* 0x46 is 'F' as in Format.
* Jan 9 01 Userland option to select format verify.
* Added PC_SUPPRESS_ERROR flag - some idefloppy drives
* do not implement IDEFLOPPY_CAPABILITIES_PAGE, and
* return a sense error. Suppress error reporting in
* this particular case in order to avoid spurious
* errors in syslog. The culprit is
* idefloppy_get_capability_page(), so move it to
* idefloppy_begin_format() so that it's not used
* unless absolutely necessary.
* If drive does not support format progress indication
* monitor the dsc bit in the status register.
* Also, O_NDELAY on open will allow the device to be
* opened without a disk available. This can be used to
* open an unformatted disk, or get the device capacity.
* Ver 0.91 Dec 11 99 Added IOMEGA Clik! drive support by
* <paul@paulbristow.net>
* Ver 0.92 Oct 22 00 Paul Bristow became official maintainer for this
* driver. Included Powerbook internal zip kludge.
* Ver 0.93 Oct 24 00 Fixed bugs for Clik! drive
* no disk on insert and disk change now works
* Ver 0.94 Oct 27 00 Tidied up to remove strstr(Clik) everywhere
* Ver 0.95 Nov 7 00 Brought across to kernel 2.4
* Ver 0.96 Jan 7 01 Actually in line with release version of 2.4.0
* including set_bit patch from Rusty Russell
* Ver 0.97 Jul 22 01 Merge 0.91-0.96 onto 0.9.sv for ac series
* Ver 0.97.sv Aug 3 01 Backported from 2.4.7-ac3
* Ver 0.98 Oct 26 01 Split idefloppy_transfer_pc into two pieces to
* fix a lost interrupt problem. It appears the busy
* bit was being deasserted by my IOMEGA ATAPI ZIP 100
* drive before the drive was actually ready.
* Ver 0.98a Oct 29 01 Expose delay value so we can play.
* Ver 0.99 Feb 24 02 Remove duplicate code, modify clik! detection code
* to support new PocketZip drives
*/
#define IDEFLOPPY_VERSION "0.99.newide"
#include <linux/config.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/interrupt.h>
#include <linux/major.h>
#include <linux/errno.h>
#include <linux/genhd.h>
#include <linux/slab.h>
#include <linux/cdrom.h>
#include <linux/ide.h>
#include <linux/bitops.h>
#include <linux/mutex.h>
#include <asm/byteorder.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/unaligned.h>
/*
* The following are used to debug the driver.
*/
#define IDEFLOPPY_DEBUG_LOG 0
#define IDEFLOPPY_DEBUG_INFO 0
#define IDEFLOPPY_DEBUG_BUGS 1
/* #define IDEFLOPPY_DEBUG(fmt, args...) printk(KERN_INFO fmt, ## args) */
#define IDEFLOPPY_DEBUG( fmt, args... )
#if IDEFLOPPY_DEBUG_LOG
#define debug_log printk
#else
#define debug_log(fmt, args... ) do {} while(0)
#endif
/*
* Some drives require a longer irq timeout.
*/
#define IDEFLOPPY_WAIT_CMD (5 * WAIT_CMD)
/*
* After each failed packet command we issue a request sense command
* and retry the packet command IDEFLOPPY_MAX_PC_RETRIES times.
*/
#define IDEFLOPPY_MAX_PC_RETRIES 3
/*
* With each packet command, we allocate a buffer of
* IDEFLOPPY_PC_BUFFER_SIZE bytes.
*/
#define IDEFLOPPY_PC_BUFFER_SIZE 256
/*
* In various places in the driver, we need to allocate storage
* for packet commands and requests, which will remain valid while
* we leave the driver to wait for an interrupt or a timeout event.
*/
#define IDEFLOPPY_PC_STACK (10 + IDEFLOPPY_MAX_PC_RETRIES)
/*
* Our view of a packet command.
*/
typedef struct idefloppy_packet_command_s {
u8 c[12]; /* Actual packet bytes */
int retries; /* On each retry, we increment retries */
int error; /* Error code */
int request_transfer; /* Bytes to transfer */
int actually_transferred; /* Bytes actually transferred */
int buffer_size; /* Size of our data buffer */
int b_count; /* Missing/Available data on the current buffer */
struct request *rq; /* The corresponding request */
u8 *buffer; /* Data buffer */
u8 *current_position; /* Pointer into the above buffer */
void (*callback) (ide_drive_t *); /* Called when this packet command is completed */
u8 pc_buffer[IDEFLOPPY_PC_BUFFER_SIZE]; /* Temporary buffer */
unsigned long flags; /* Status/Action bit flags: long for set_bit */
} idefloppy_pc_t;
/*
* Packet command flag bits.
*/
#define PC_ABORT 0 /* Set when an error is considered normal - We won't retry */
#define PC_DMA_RECOMMENDED 2 /* 1 when we prefer to use DMA if possible */
#define PC_DMA_IN_PROGRESS 3 /* 1 while DMA in progress */
#define PC_DMA_ERROR 4 /* 1 when encountered problem during DMA */
#define PC_WRITING 5 /* Data direction */
#define PC_SUPPRESS_ERROR 6 /* Suppress error reporting */
/*
* Removable Block Access Capabilities Page
*/
typedef struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned page_code :6; /* Page code - Should be 0x1b */
unsigned reserved1_6 :1; /* Reserved */
unsigned ps :1; /* Should be 0 */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned ps :1; /* Should be 0 */
unsigned reserved1_6 :1; /* Reserved */
unsigned page_code :6; /* Page code - Should be 0x1b */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 page_length; /* Page Length - Should be 0xa */
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned reserved2 :6;
unsigned srfp :1; /* Supports reporting progress of format */
unsigned sflp :1; /* System floppy type device */
unsigned tlun :3; /* Total logical units supported by the device */
unsigned reserved3 :3;
unsigned sml :1; /* Single / Multiple lun supported */
unsigned ncd :1; /* Non cd optical device */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned sflp :1; /* System floppy type device */
unsigned srfp :1; /* Supports reporting progress of format */
unsigned reserved2 :6;
unsigned ncd :1; /* Non cd optical device */
unsigned sml :1; /* Single / Multiple lun supported */
unsigned reserved3 :3;
unsigned tlun :3; /* Total logical units supported by the device */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 reserved[8];
} idefloppy_capabilities_page_t;
/*
* Flexible disk page.
*/
typedef struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned page_code :6; /* Page code - Should be 0x5 */
unsigned reserved1_6 :1; /* Reserved */
unsigned ps :1; /* The device is capable of saving the page */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned ps :1; /* The device is capable of saving the page */
unsigned reserved1_6 :1; /* Reserved */
unsigned page_code :6; /* Page code - Should be 0x5 */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 page_length; /* Page Length - Should be 0x1e */
u16 transfer_rate; /* In kilobits per second */
u8 heads, sectors; /* Number of heads, Number of sectors per track */
u16 sector_size; /* Byes per sector */
u16 cyls; /* Number of cylinders */
u8 reserved10[10];
u8 motor_delay; /* Motor off delay */
u8 reserved21[7];
u16 rpm; /* Rotations per minute */
u8 reserved30[2];
} idefloppy_flexible_disk_page_t;
/*
* Format capacity
*/
typedef struct {
u8 reserved[3];
u8 length; /* Length of the following descriptors in bytes */
} idefloppy_capacity_header_t;
typedef struct {
u32 blocks; /* Number of blocks */
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned dc :2; /* Descriptor Code */
unsigned reserved :6;
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned reserved :6;
unsigned dc :2; /* Descriptor Code */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 length_msb; /* Block Length (MSB)*/
u16 length; /* Block Length */
} idefloppy_capacity_descriptor_t;
#define CAPACITY_INVALID 0x00
#define CAPACITY_UNFORMATTED 0x01
#define CAPACITY_CURRENT 0x02
#define CAPACITY_NO_CARTRIDGE 0x03
/*
* Most of our global data which we need to save even as we leave the
* driver due to an interrupt or a timer event is stored in a variable
* of type idefloppy_floppy_t, defined below.
*/
typedef struct ide_floppy_obj {
ide_drive_t *drive;
ide_driver_t *driver;
struct gendisk *disk;
struct kref kref;
/* Current packet command */
idefloppy_pc_t *pc;
/* Last failed packet command */
idefloppy_pc_t *failed_pc;
/* Packet command stack */
idefloppy_pc_t pc_stack[IDEFLOPPY_PC_STACK];
/* Next free packet command storage space */
int pc_stack_index;
struct request rq_stack[IDEFLOPPY_PC_STACK];
/* We implement a circular array */
int rq_stack_index;
/*
* Last error information
*/
u8 sense_key, asc, ascq;
/* delay this long before sending packet command */
u8 ticks;
int progress_indication;
/*
* Device information
*/
/* Current format */
int blocks, block_size, bs_factor;
/* Last format capacity */
idefloppy_capacity_descriptor_t capacity;
/* Copy of the flexible disk page */
idefloppy_flexible_disk_page_t flexible_disk_page;
/* Write protect */
int wp;
/* Supports format progress report */
int srfp;
/* Status/Action flags */
unsigned long flags;
} idefloppy_floppy_t;
#define IDEFLOPPY_TICKS_DELAY HZ/20 /* default delay for ZIP 100 (50ms) */
/*
* Floppy flag bits values.
*/
#define IDEFLOPPY_DRQ_INTERRUPT 0 /* DRQ interrupt device */
#define IDEFLOPPY_MEDIA_CHANGED 1 /* Media may have changed */
#define IDEFLOPPY_USE_READ12 2 /* Use READ12/WRITE12 or READ10/WRITE10 */
#define IDEFLOPPY_FORMAT_IN_PROGRESS 3 /* Format in progress */
#define IDEFLOPPY_CLIK_DRIVE 4 /* Avoid commands not supported in Clik drive */
#define IDEFLOPPY_ZIP_DRIVE 5 /* Requires BH algorithm for packets */
/*
* ATAPI floppy drive packet commands
*/
#define IDEFLOPPY_FORMAT_UNIT_CMD 0x04
#define IDEFLOPPY_INQUIRY_CMD 0x12
#define IDEFLOPPY_MODE_SELECT_CMD 0x55
#define IDEFLOPPY_MODE_SENSE_CMD 0x5a
#define IDEFLOPPY_READ10_CMD 0x28
#define IDEFLOPPY_READ12_CMD 0xa8
#define IDEFLOPPY_READ_CAPACITY_CMD 0x23
#define IDEFLOPPY_REQUEST_SENSE_CMD 0x03
#define IDEFLOPPY_PREVENT_REMOVAL_CMD 0x1e
#define IDEFLOPPY_SEEK_CMD 0x2b
#define IDEFLOPPY_START_STOP_CMD 0x1b
#define IDEFLOPPY_TEST_UNIT_READY_CMD 0x00
#define IDEFLOPPY_VERIFY_CMD 0x2f
#define IDEFLOPPY_WRITE10_CMD 0x2a
#define IDEFLOPPY_WRITE12_CMD 0xaa
#define IDEFLOPPY_WRITE_VERIFY_CMD 0x2e
/*
* Defines for the mode sense command
*/
#define MODE_SENSE_CURRENT 0x00
#define MODE_SENSE_CHANGEABLE 0x01
#define MODE_SENSE_DEFAULT 0x02
#define MODE_SENSE_SAVED 0x03
/*
* IOCTLs used in low-level formatting.
*/
#define IDEFLOPPY_IOCTL_FORMAT_SUPPORTED 0x4600
#define IDEFLOPPY_IOCTL_FORMAT_GET_CAPACITY 0x4601
#define IDEFLOPPY_IOCTL_FORMAT_START 0x4602
#define IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS 0x4603
#if 0
/*
* Special requests for our block device strategy routine.
*/
#define IDEFLOPPY_FIRST_RQ 90
/*
* IDEFLOPPY_PC_RQ is used to queue a packet command in the request queue.
*/
#define IDEFLOPPY_PC_RQ 90
#define IDEFLOPPY_LAST_RQ 90
/*
* A macro which can be used to check if a given request command
* originated in the driver or in the buffer cache layer.
*/
#define IDEFLOPPY_RQ_CMD(cmd) ((cmd >= IDEFLOPPY_FIRST_RQ) && (cmd <= IDEFLOPPY_LAST_RQ))
#endif
/*
* Error codes which are returned in rq->errors to the higher part
* of the driver.
*/
#define IDEFLOPPY_ERROR_GENERAL 101
/*
* The following is used to format the general configuration word of
* the ATAPI IDENTIFY DEVICE command.
*/
struct idefloppy_id_gcw {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned packet_size :2; /* Packet Size */
unsigned reserved234 :3; /* Reserved */
unsigned drq_type :2; /* Command packet DRQ type */
unsigned removable :1; /* Removable media */
unsigned device_type :5; /* Device type */
unsigned reserved13 :1; /* Reserved */
unsigned protocol :2; /* Protocol type */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned protocol :2; /* Protocol type */
unsigned reserved13 :1; /* Reserved */
unsigned device_type :5; /* Device type */
unsigned removable :1; /* Removable media */
unsigned drq_type :2; /* Command packet DRQ type */
unsigned reserved234 :3; /* Reserved */
unsigned packet_size :2; /* Packet Size */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
};
/*
* INQUIRY packet command - Data Format
*/
typedef struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned device_type :5; /* Peripheral Device Type */
unsigned reserved0_765 :3; /* Peripheral Qualifier - Reserved */
unsigned reserved1_6t0 :7; /* Reserved */
unsigned rmb :1; /* Removable Medium Bit */
unsigned ansi_version :3; /* ANSI Version */
unsigned ecma_version :3; /* ECMA Version */
unsigned iso_version :2; /* ISO Version */
unsigned response_format :4; /* Response Data Format */
unsigned reserved3_45 :2; /* Reserved */
unsigned reserved3_6 :1; /* TrmIOP - Reserved */
unsigned reserved3_7 :1; /* AENC - Reserved */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned reserved0_765 :3; /* Peripheral Qualifier - Reserved */
unsigned device_type :5; /* Peripheral Device Type */
unsigned rmb :1; /* Removable Medium Bit */
unsigned reserved1_6t0 :7; /* Reserved */
unsigned iso_version :2; /* ISO Version */
unsigned ecma_version :3; /* ECMA Version */
unsigned ansi_version :3; /* ANSI Version */
unsigned reserved3_7 :1; /* AENC - Reserved */
unsigned reserved3_6 :1; /* TrmIOP - Reserved */
unsigned reserved3_45 :2; /* Reserved */
unsigned response_format :4; /* Response Data Format */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 additional_length; /* Additional Length (total_length-4) */
u8 rsv5, rsv6, rsv7; /* Reserved */
u8 vendor_id[8]; /* Vendor Identification */
u8 product_id[16]; /* Product Identification */
u8 revision_level[4]; /* Revision Level */
u8 vendor_specific[20]; /* Vendor Specific - Optional */
u8 reserved56t95[40]; /* Reserved - Optional */
/* Additional information may be returned */
} idefloppy_inquiry_result_t;
/*
* REQUEST SENSE packet command result - Data Format.
*/
typedef struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned error_code :7; /* Current error (0x70) */
unsigned valid :1; /* The information field conforms to SFF-8070i */
u8 reserved1 :8; /* Reserved */
unsigned sense_key :4; /* Sense Key */
unsigned reserved2_4 :1; /* Reserved */
unsigned ili :1; /* Incorrect Length Indicator */
unsigned reserved2_67 :2;
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned valid :1; /* The information field conforms to SFF-8070i */
unsigned error_code :7; /* Current error (0x70) */
u8 reserved1 :8; /* Reserved */
unsigned reserved2_67 :2;
unsigned ili :1; /* Incorrect Length Indicator */
unsigned reserved2_4 :1; /* Reserved */
unsigned sense_key :4; /* Sense Key */
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u32 information __attribute__ ((packed));
u8 asl; /* Additional sense length (n-7) */
u32 command_specific; /* Additional command specific information */
u8 asc; /* Additional Sense Code */
u8 ascq; /* Additional Sense Code Qualifier */
u8 replaceable_unit_code; /* Field Replaceable Unit Code */
u8 sksv[3];
u8 pad[2]; /* Padding to 20 bytes */
} idefloppy_request_sense_result_t;
/*
* Pages of the SELECT SENSE / MODE SENSE packet commands.
*/
#define IDEFLOPPY_CAPABILITIES_PAGE 0x1b
#define IDEFLOPPY_FLEXIBLE_DISK_PAGE 0x05
/*
* Mode Parameter Header for the MODE SENSE packet command
*/
typedef struct {
u16 mode_data_length; /* Length of the following data transfer */
u8 medium_type; /* Medium Type */
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned reserved3 :7;
unsigned wp :1; /* Write protect */
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned wp :1; /* Write protect */
unsigned reserved3 :7;
#else
#error "Bitfield endianness not defined! Check your byteorder.h"
#endif
u8 reserved[4];
} idefloppy_mode_parameter_header_t;
static DEFINE_MUTEX(idefloppy_ref_mutex);
#define to_ide_floppy(obj) container_of(obj, struct ide_floppy_obj, kref)
#define ide_floppy_g(disk) \
container_of((disk)->private_data, struct ide_floppy_obj, driver)
static struct ide_floppy_obj *ide_floppy_get(struct gendisk *disk)
{
struct ide_floppy_obj *floppy = NULL;
mutex_lock(&idefloppy_ref_mutex);
floppy = ide_floppy_g(disk);
if (floppy)
kref_get(&floppy->kref);
mutex_unlock(&idefloppy_ref_mutex);
return floppy;
}
static void ide_floppy_release(struct kref *);
static void ide_floppy_put(struct ide_floppy_obj *floppy)
{
mutex_lock(&idefloppy_ref_mutex);
kref_put(&floppy->kref, ide_floppy_release);
mutex_unlock(&idefloppy_ref_mutex);
}
/*
* Too bad. The drive wants to send us data which we are not ready to accept.
* Just throw it away.
*/
static void idefloppy_discard_data (ide_drive_t *drive, unsigned int bcount)
{
while (bcount--)
(void) HWIF(drive)->INB(IDE_DATA_REG);
}
#if IDEFLOPPY_DEBUG_BUGS
static void idefloppy_write_zeros (ide_drive_t *drive, unsigned int bcount)
{
while (bcount--)
HWIF(drive)->OUTB(0, IDE_DATA_REG);
}
#endif /* IDEFLOPPY_DEBUG_BUGS */
/*
* idefloppy_do_end_request is used to finish servicing a request.
*
* For read/write requests, we will call ide_end_request to pass to the
* next buffer.
*/
static int idefloppy_do_end_request(ide_drive_t *drive, int uptodate, int nsecs)
{
idefloppy_floppy_t *floppy = drive->driver_data;
struct request *rq = HWGROUP(drive)->rq;
int error;
debug_log(KERN_INFO "Reached idefloppy_end_request\n");
switch (uptodate) {
case 0: error = IDEFLOPPY_ERROR_GENERAL; break;
case 1: error = 0; break;
default: error = uptodate;
}
if (error)
floppy->failed_pc = NULL;
/* Why does this happen? */
if (!rq)
return 0;
if (!(rq->flags & REQ_SPECIAL)) { //if (!IDEFLOPPY_RQ_CMD (rq->cmd)) {
/* our real local end request function */
ide_end_request(drive, uptodate, nsecs);
return 0;
}
rq->errors = error;
/* fixme: need to move this local also */
ide_end_drive_cmd(drive, 0, 0);
return 0;
}
static void idefloppy_input_buffers (ide_drive_t *drive, idefloppy_pc_t *pc, unsigned int bcount)
{
struct request *rq = pc->rq;
struct bio_vec *bvec;
struct bio *bio;
unsigned long flags;
char *data;
int count, i, done = 0;
rq_for_each_bio(bio, rq) {
bio_for_each_segment(bvec, bio, i) {
if (!bcount)
break;
count = min(bvec->bv_len, bcount);
data = bvec_kmap_irq(bvec, &flags);
drive->hwif->atapi_input_bytes(drive, data, count);
bvec_kunmap_irq(data, &flags);
bcount -= count;
pc->b_count += count;
done += count;
}
}
idefloppy_do_end_request(drive, 1, done >> 9);
if (bcount) {
printk(KERN_ERR "%s: leftover data in idefloppy_input_buffers, bcount == %d\n", drive->name, bcount);
idefloppy_discard_data(drive, bcount);
}
}
static void idefloppy_output_buffers (ide_drive_t *drive, idefloppy_pc_t *pc, unsigned int bcount)
{
struct request *rq = pc->rq;
struct bio *bio;
struct bio_vec *bvec;
unsigned long flags;
int count, i, done = 0;
char *data;
rq_for_each_bio(bio, rq) {
bio_for_each_segment(bvec, bio, i) {
if (!bcount)
break;
count = min(bvec->bv_len, bcount);
data = bvec_kmap_irq(bvec, &flags);
drive->hwif->atapi_output_bytes(drive, data, count);
bvec_kunmap_irq(data, &flags);
bcount -= count;
pc->b_count += count;
done += count;
}
}
idefloppy_do_end_request(drive, 1, done >> 9);
#if IDEFLOPPY_DEBUG_BUGS
if (bcount) {
printk(KERN_ERR "%s: leftover data in idefloppy_output_buffers, bcount == %d\n", drive->name, bcount);
idefloppy_write_zeros(drive, bcount);
}
#endif
}
static void idefloppy_update_buffers (ide_drive_t *drive, idefloppy_pc_t *pc)
{
struct request *rq = pc->rq;
struct bio *bio = rq->bio;
while ((bio = rq->bio) != NULL)
idefloppy_do_end_request(drive, 1, 0);
}
/*
* idefloppy_queue_pc_head generates a new packet command request in front
* of the request queue, before the current request, so that it will be
* processed immediately, on the next pass through the driver.
*/
static void idefloppy_queue_pc_head (ide_drive_t *drive,idefloppy_pc_t *pc,struct request *rq)
{
struct ide_floppy_obj *floppy = drive->driver_data;
ide_init_drive_cmd(rq);
rq->buffer = (char *) pc;
rq->flags = REQ_SPECIAL; //rq->cmd = IDEFLOPPY_PC_RQ;
rq->rq_disk = floppy->disk;
(void) ide_do_drive_cmd(drive, rq, ide_preempt);
}
static idefloppy_pc_t *idefloppy_next_pc_storage (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
if (floppy->pc_stack_index == IDEFLOPPY_PC_STACK)
floppy->pc_stack_index=0;
return (&floppy->pc_stack[floppy->pc_stack_index++]);
}
static struct request *idefloppy_next_rq_storage (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
if (floppy->rq_stack_index == IDEFLOPPY_PC_STACK)
floppy->rq_stack_index = 0;
return (&floppy->rq_stack[floppy->rq_stack_index++]);
}
/*
* idefloppy_analyze_error is called on each failed packet command retry
* to analyze the request sense.
*/
static void idefloppy_analyze_error (ide_drive_t *drive,idefloppy_request_sense_result_t *result)
{
idefloppy_floppy_t *floppy = drive->driver_data;
floppy->sense_key = result->sense_key;
floppy->asc = result->asc;
floppy->ascq = result->ascq;
floppy->progress_indication = result->sksv[0] & 0x80 ?
(u16)get_unaligned((u16 *)(result->sksv+1)):0x10000;
if (floppy->failed_pc)
debug_log(KERN_INFO "ide-floppy: pc = %x, sense key = %x, "
"asc = %x, ascq = %x\n", floppy->failed_pc->c[0],
result->sense_key, result->asc, result->ascq);
else
debug_log(KERN_INFO "ide-floppy: sense key = %x, asc = %x, "
"ascq = %x\n", result->sense_key,
result->asc, result->ascq);
}
static void idefloppy_request_sense_callback (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
debug_log(KERN_INFO "ide-floppy: Reached %s\n", __FUNCTION__);
if (!floppy->pc->error) {
idefloppy_analyze_error(drive,(idefloppy_request_sense_result_t *) floppy->pc->buffer);
idefloppy_do_end_request(drive, 1, 0);
} else {
printk(KERN_ERR "Error in REQUEST SENSE itself - Aborting request!\n");
idefloppy_do_end_request(drive, 0, 0);
}
}
/*
* General packet command callback function.
*/
static void idefloppy_pc_callback (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
debug_log(KERN_INFO "ide-floppy: Reached %s\n", __FUNCTION__);
idefloppy_do_end_request(drive, floppy->pc->error ? 0 : 1, 0);
}
/*
* idefloppy_init_pc initializes a packet command.
*/
static void idefloppy_init_pc (idefloppy_pc_t *pc)
{
memset(pc->c, 0, 12);
pc->retries = 0;
pc->flags = 0;
pc->request_transfer = 0;
pc->buffer = pc->pc_buffer;
pc->buffer_size = IDEFLOPPY_PC_BUFFER_SIZE;
pc->callback = &idefloppy_pc_callback;
}
static void idefloppy_create_request_sense_cmd (idefloppy_pc_t *pc)
{
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_REQUEST_SENSE_CMD;
pc->c[4] = 255;
pc->request_transfer = 18;
pc->callback = &idefloppy_request_sense_callback;
}
/*
* idefloppy_retry_pc is called when an error was detected during the
* last packet command. We queue a request sense packet command in
* the head of the request list.
*/
static void idefloppy_retry_pc (ide_drive_t *drive)
{
idefloppy_pc_t *pc;
struct request *rq;
atapi_error_t error;
error.all = HWIF(drive)->INB(IDE_ERROR_REG);
pc = idefloppy_next_pc_storage(drive);
rq = idefloppy_next_rq_storage(drive);
idefloppy_create_request_sense_cmd(pc);
idefloppy_queue_pc_head(drive, pc, rq);
}
/*
* idefloppy_pc_intr is the usual interrupt handler which will be called
* during a packet command.
*/
static ide_startstop_t idefloppy_pc_intr (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
atapi_status_t status;
atapi_bcount_t bcount;
atapi_ireason_t ireason;
idefloppy_pc_t *pc = floppy->pc;
struct request *rq = pc->rq;
unsigned int temp;
debug_log(KERN_INFO "ide-floppy: Reached %s interrupt handler\n",
__FUNCTION__);
if (test_bit(PC_DMA_IN_PROGRESS, &pc->flags)) {
if (HWIF(drive)->ide_dma_end(drive)) {
set_bit(PC_DMA_ERROR, &pc->flags);
} else {
pc->actually_transferred = pc->request_transfer;
idefloppy_update_buffers(drive, pc);
}
debug_log(KERN_INFO "ide-floppy: DMA finished\n");
}
/* Clear the interrupt */
status.all = HWIF(drive)->INB(IDE_STATUS_REG);
if (!status.b.drq) { /* No more interrupts */
debug_log(KERN_INFO "Packet command completed, %d bytes "
"transferred\n", pc->actually_transferred);
clear_bit(PC_DMA_IN_PROGRESS, &pc->flags);
local_irq_enable();
if (status.b.check || test_bit(PC_DMA_ERROR, &pc->flags)) {
/* Error detected */
debug_log(KERN_INFO "ide-floppy: %s: I/O error\n",
drive->name);
rq->errors++;
if (pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD) {
printk(KERN_ERR "ide-floppy: I/O error in "
"request sense command\n");
return ide_do_reset(drive);
}
/* Retry operation */
idefloppy_retry_pc(drive);
/* queued, but not started */
return ide_stopped;
}
pc->error = 0;
if (floppy->failed_pc == pc)
floppy->failed_pc = NULL;
/* Command finished - Call the callback function */
pc->callback(drive);
return ide_stopped;
}
if (test_and_clear_bit(PC_DMA_IN_PROGRESS, &pc->flags)) {
printk(KERN_ERR "ide-floppy: The floppy wants to issue "
"more interrupts in DMA mode\n");
(void)__ide_dma_off(drive);
return ide_do_reset(drive);
}
/* Get the number of bytes to transfer */
bcount.b.high = HWIF(drive)->INB(IDE_BCOUNTH_REG);
bcount.b.low = HWIF(drive)->INB(IDE_BCOUNTL_REG);
/* on this interrupt */
ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
if (ireason.b.cod) {
printk(KERN_ERR "ide-floppy: CoD != 0 in idefloppy_pc_intr\n");
return ide_do_reset(drive);
}
if (ireason.b.io == test_bit(PC_WRITING, &pc->flags)) {
/* Hopefully, we will never get here */
printk(KERN_ERR "ide-floppy: We wanted to %s, ",
ireason.b.io ? "Write":"Read");
printk(KERN_ERR "but the floppy wants us to %s !\n",
ireason.b.io ? "Read":"Write");
return ide_do_reset(drive);
}
if (!test_bit(PC_WRITING, &pc->flags)) {
/* Reading - Check that we have enough space */
temp = pc->actually_transferred + bcount.all;
if (temp > pc->request_transfer) {
if (temp > pc->buffer_size) {
printk(KERN_ERR "ide-floppy: The floppy wants "
"to send us more data than expected "
"- discarding data\n");
idefloppy_discard_data(drive,bcount.all);
BUG_ON(HWGROUP(drive)->handler != NULL);
ide_set_handler(drive,
&idefloppy_pc_intr,
IDEFLOPPY_WAIT_CMD,
NULL);
return ide_started;
}
debug_log(KERN_NOTICE "ide-floppy: The floppy wants to "
"send us more data than expected - "
"allowing transfer\n");
}
}
if (test_bit(PC_WRITING, &pc->flags)) {
if (pc->buffer != NULL)
/* Write the current buffer */
HWIF(drive)->atapi_output_bytes(drive,
pc->current_position,
bcount.all);
else
idefloppy_output_buffers(drive, pc, bcount.all);
} else {
if (pc->buffer != NULL)
/* Read the current buffer */
HWIF(drive)->atapi_input_bytes(drive,
pc->current_position,
bcount.all);
else
idefloppy_input_buffers(drive, pc, bcount.all);
}
/* Update the current position */
pc->actually_transferred += bcount.all;
pc->current_position += bcount.all;
BUG_ON(HWGROUP(drive)->handler != NULL);
ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL); /* And set the interrupt handler again */
return ide_started;
}
/*
* This is the original routine that did the packet transfer.
* It fails at high speeds on the Iomega ZIP drive, so there's a slower version
* for that drive below. The algorithm is chosen based on drive type
*/
static ide_startstop_t idefloppy_transfer_pc (ide_drive_t *drive)
{
ide_startstop_t startstop;
idefloppy_floppy_t *floppy = drive->driver_data;
atapi_ireason_t ireason;
if (ide_wait_stat(&startstop, drive, DRQ_STAT, BUSY_STAT, WAIT_READY)) {
printk(KERN_ERR "ide-floppy: Strange, packet command "
"initiated yet DRQ isn't asserted\n");
return startstop;
}
ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
if (!ireason.b.cod || ireason.b.io) {
printk(KERN_ERR "ide-floppy: (IO,CoD) != (0,1) while "
"issuing a packet command\n");
return ide_do_reset(drive);
}
BUG_ON(HWGROUP(drive)->handler != NULL);
/* Set the interrupt routine */
ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL);
/* Send the actual packet */
HWIF(drive)->atapi_output_bytes(drive, floppy->pc->c, 12);
return ide_started;
}
/*
* What we have here is a classic case of a top half / bottom half
* interrupt service routine. In interrupt mode, the device sends
* an interrupt to signal it's ready to receive a packet. However,
* we need to delay about 2-3 ticks before issuing the packet or we
* gets in trouble.
*
* So, follow carefully. transfer_pc1 is called as an interrupt (or
* directly). In either case, when the device says it's ready for a
* packet, we schedule the packet transfer to occur about 2-3 ticks
* later in transfer_pc2.
*/
static int idefloppy_transfer_pc2 (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
/* Send the actual packet */
HWIF(drive)->atapi_output_bytes(drive, floppy->pc->c, 12);
/* Timeout for the packet command */
return IDEFLOPPY_WAIT_CMD;
}
static ide_startstop_t idefloppy_transfer_pc1 (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
ide_startstop_t startstop;
atapi_ireason_t ireason;
if (ide_wait_stat(&startstop, drive, DRQ_STAT, BUSY_STAT, WAIT_READY)) {
printk(KERN_ERR "ide-floppy: Strange, packet command "
"initiated yet DRQ isn't asserted\n");
return startstop;
}
ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
if (!ireason.b.cod || ireason.b.io) {
printk(KERN_ERR "ide-floppy: (IO,CoD) != (0,1) "
"while issuing a packet command\n");
return ide_do_reset(drive);
}
/*
* The following delay solves a problem with ATAPI Zip 100 drives
* where the Busy flag was apparently being deasserted before the
* unit was ready to receive data. This was happening on a
* 1200 MHz Athlon system. 10/26/01 25msec is too short,
* 40 and 50msec work well. idefloppy_pc_intr will not be actually
* used until after the packet is moved in about 50 msec.
*/
BUG_ON(HWGROUP(drive)->handler != NULL);
ide_set_handler(drive,
&idefloppy_pc_intr, /* service routine for packet command */
floppy->ticks, /* wait this long before "failing" */
&idefloppy_transfer_pc2); /* fail == transfer_pc2 */
return ide_started;
}
/**
* idefloppy_should_report_error()
*
* Supresses error messages resulting from Medium not present
*/
static inline int idefloppy_should_report_error(idefloppy_floppy_t *floppy)
{
if (floppy->sense_key == 0x02 &&
floppy->asc == 0x3a &&
floppy->ascq == 0x00)
return 0;
return 1;
}
/*
* Issue a packet command
*/
static ide_startstop_t idefloppy_issue_pc (ide_drive_t *drive, idefloppy_pc_t *pc)
{
idefloppy_floppy_t *floppy = drive->driver_data;
ide_hwif_t *hwif = drive->hwif;
atapi_feature_t feature;
atapi_bcount_t bcount;
ide_handler_t *pkt_xfer_routine;
#if 0 /* Accessing floppy->pc is not valid here, the previous pc may be gone
and have lived on another thread's stack; that stack may have become
unmapped meanwhile (CONFIG_DEBUG_PAGEALLOC). */
#if IDEFLOPPY_DEBUG_BUGS
if (floppy->pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD &&
pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD) {
printk(KERN_ERR "ide-floppy: possible ide-floppy.c bug - "
"Two request sense in serial were issued\n");
}
#endif /* IDEFLOPPY_DEBUG_BUGS */
#endif
if (floppy->failed_pc == NULL &&
pc->c[0] != IDEFLOPPY_REQUEST_SENSE_CMD)
floppy->failed_pc = pc;
/* Set the current packet command */
floppy->pc = pc;
if (pc->retries > IDEFLOPPY_MAX_PC_RETRIES ||
test_bit(PC_ABORT, &pc->flags)) {
/*
* We will "abort" retrying a packet command in case
* a legitimate error code was received.
*/
if (!test_bit(PC_ABORT, &pc->flags)) {
if (!test_bit(PC_SUPPRESS_ERROR, &pc->flags)) {
if (idefloppy_should_report_error(floppy))
printk(KERN_ERR "ide-floppy: %s: I/O error, "
"pc = %2x, key = %2x, "
"asc = %2x, ascq = %2x\n",
drive->name, pc->c[0],
floppy->sense_key,
floppy->asc, floppy->ascq);
}
/* Giving up */
pc->error = IDEFLOPPY_ERROR_GENERAL;
}
floppy->failed_pc = NULL;
pc->callback(drive);
return ide_stopped;
}
debug_log(KERN_INFO "Retry number - %d\n",pc->retries);
pc->retries++;
/* We haven't transferred any data yet */
pc->actually_transferred = 0;
pc->current_position = pc->buffer;
bcount.all = min(pc->request_transfer, 63 * 1024);
if (test_and_clear_bit(PC_DMA_ERROR, &pc->flags)) {
(void)__ide_dma_off(drive);
}
feature.all = 0;
if (test_bit(PC_DMA_RECOMMENDED, &pc->flags) && drive->using_dma)
feature.b.dma = !hwif->dma_setup(drive);
if (IDE_CONTROL_REG)
HWIF(drive)->OUTB(drive->ctl, IDE_CONTROL_REG);
/* Use PIO/DMA */
HWIF(drive)->OUTB(feature.all, IDE_FEATURE_REG);
HWIF(drive)->OUTB(bcount.b.high, IDE_BCOUNTH_REG);
HWIF(drive)->OUTB(bcount.b.low, IDE_BCOUNTL_REG);
HWIF(drive)->OUTB(drive->select.all, IDE_SELECT_REG);
if (feature.b.dma) { /* Begin DMA, if necessary */
set_bit(PC_DMA_IN_PROGRESS, &pc->flags);
hwif->dma_start(drive);
}
/* Can we transfer the packet when we get the interrupt or wait? */
if (test_bit(IDEFLOPPY_ZIP_DRIVE, &floppy->flags)) {
/* wait */
pkt_xfer_routine = &idefloppy_transfer_pc1;
} else {
/* immediate */
pkt_xfer_routine = &idefloppy_transfer_pc;
}
if (test_bit (IDEFLOPPY_DRQ_INTERRUPT, &floppy->flags)) {
/* Issue the packet command */
ide_execute_command(drive, WIN_PACKETCMD,
pkt_xfer_routine,
IDEFLOPPY_WAIT_CMD,
NULL);
return ide_started;
} else {
/* Issue the packet command */
HWIF(drive)->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG);
return (*pkt_xfer_routine) (drive);
}
}
static void idefloppy_rw_callback (ide_drive_t *drive)
{
debug_log(KERN_INFO "ide-floppy: Reached idefloppy_rw_callback\n");
idefloppy_do_end_request(drive, 1, 0);
return;
}
static void idefloppy_create_prevent_cmd (idefloppy_pc_t *pc, int prevent)
{
debug_log(KERN_INFO "ide-floppy: creating prevent removal command, "
"prevent = %d\n", prevent);
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_PREVENT_REMOVAL_CMD;
pc->c[4] = prevent;
}
static void idefloppy_create_read_capacity_cmd (idefloppy_pc_t *pc)
{
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_READ_CAPACITY_CMD;
pc->c[7] = 255;
pc->c[8] = 255;
pc->request_transfer = 255;
}
static void idefloppy_create_format_unit_cmd (idefloppy_pc_t *pc, int b, int l,
int flags)
{
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_FORMAT_UNIT_CMD;
pc->c[1] = 0x17;
memset(pc->buffer, 0, 12);
pc->buffer[1] = 0xA2;
/* Default format list header, u8 1: FOV/DCRT/IMM bits set */
if (flags & 1) /* Verify bit on... */
pc->buffer[1] ^= 0x20; /* ... turn off DCRT bit */
pc->buffer[3] = 8;
put_unaligned(htonl(b), (unsigned int *)(&pc->buffer[4]));
put_unaligned(htonl(l), (unsigned int *)(&pc->buffer[8]));
pc->buffer_size=12;
set_bit(PC_WRITING, &pc->flags);
}
/*
* A mode sense command is used to "sense" floppy parameters.
*/
static void idefloppy_create_mode_sense_cmd (idefloppy_pc_t *pc, u8 page_code, u8 type)
{
u16 length = sizeof(idefloppy_mode_parameter_header_t);
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_MODE_SENSE_CMD;
pc->c[1] = 0;
pc->c[2] = page_code + (type << 6);
switch (page_code) {
case IDEFLOPPY_CAPABILITIES_PAGE:
length += 12;
break;
case IDEFLOPPY_FLEXIBLE_DISK_PAGE:
length += 32;
break;
default:
printk(KERN_ERR "ide-floppy: unsupported page code "
"in create_mode_sense_cmd\n");
}
put_unaligned(htons(length), (u16 *) &pc->c[7]);
pc->request_transfer = length;
}
static void idefloppy_create_start_stop_cmd (idefloppy_pc_t *pc, int start)
{
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_START_STOP_CMD;
pc->c[4] = start;
}
static void idefloppy_create_test_unit_ready_cmd(idefloppy_pc_t *pc)
{
idefloppy_init_pc(pc);
pc->c[0] = IDEFLOPPY_TEST_UNIT_READY_CMD;
}
static void idefloppy_create_rw_cmd (idefloppy_floppy_t *floppy, idefloppy_pc_t *pc, struct request *rq, unsigned long sector)
{
int block = sector / floppy->bs_factor;
int blocks = rq->nr_sectors / floppy->bs_factor;
int cmd = rq_data_dir(rq);
debug_log("create_rw1%d_cmd: block == %d, blocks == %d\n",
2 * test_bit (IDEFLOPPY_USE_READ12, &floppy->flags),
block, blocks);
idefloppy_init_pc(pc);
if (test_bit(IDEFLOPPY_USE_READ12, &floppy->flags)) {
pc->c[0] = cmd == READ ? IDEFLOPPY_READ12_CMD : IDEFLOPPY_WRITE12_CMD;
put_unaligned(htonl(blocks), (unsigned int *) &pc->c[6]);
} else {
pc->c[0] = cmd == READ ? IDEFLOPPY_READ10_CMD : IDEFLOPPY_WRITE10_CMD;
put_unaligned(htons(blocks), (unsigned short *) &pc->c[7]);
}
put_unaligned(htonl(block), (unsigned int *) &pc->c[2]);
pc->callback = &idefloppy_rw_callback;
pc->rq = rq;
pc->b_count = cmd == READ ? 0 : rq->bio->bi_size;
if (rq->flags & REQ_RW)
set_bit(PC_WRITING, &pc->flags);
pc->buffer = NULL;
pc->request_transfer = pc->buffer_size = blocks * floppy->block_size;
set_bit(PC_DMA_RECOMMENDED, &pc->flags);
}
static int
idefloppy_blockpc_cmd(idefloppy_floppy_t *floppy, idefloppy_pc_t *pc, struct request *rq)
{
/*
* just support eject for now, it would not be hard to make the
* REQ_BLOCK_PC support fully-featured
*/
if (rq->cmd[0] != IDEFLOPPY_START_STOP_CMD)
return 1;
idefloppy_init_pc(pc);
memcpy(pc->c, rq->cmd, sizeof(pc->c));
return 0;
}
/*
* idefloppy_do_request is our request handling function.
*/
static ide_startstop_t idefloppy_do_request (ide_drive_t *drive, struct request *rq, sector_t block_s)
{
idefloppy_floppy_t *floppy = drive->driver_data;
idefloppy_pc_t *pc;
unsigned long block = (unsigned long)block_s;
debug_log(KERN_INFO "rq_status: %d, dev: %s, flags: %lx, errors: %d\n",
rq->rq_status,
rq->rq_disk ? rq->rq_disk->disk_name ? "?",
rq->flags, rq->errors);
debug_log(KERN_INFO "sector: %ld, nr_sectors: %ld, "
"current_nr_sectors: %d\n", (long)rq->sector,
rq->nr_sectors, rq->current_nr_sectors);
if (rq->errors >= ERROR_MAX) {
if (floppy->failed_pc != NULL) {
if (idefloppy_should_report_error(floppy))
printk(KERN_ERR "ide-floppy: %s: I/O error, pc = %2x,"
" key = %2x, asc = %2x, ascq = %2x\n",
drive->name, floppy->failed_pc->c[0],
floppy->sense_key, floppy->asc, floppy->ascq);
}
else
printk(KERN_ERR "ide-floppy: %s: I/O error\n",
drive->name);
idefloppy_do_end_request(drive, 0, 0);
return ide_stopped;
}
if (rq->flags & REQ_CMD) {
if (((long)rq->sector % floppy->bs_factor) ||
(rq->nr_sectors % floppy->bs_factor)) {
printk("%s: unsupported r/w request size\n",
drive->name);
idefloppy_do_end_request(drive, 0, 0);
return ide_stopped;
}
pc = idefloppy_next_pc_storage(drive);
idefloppy_create_rw_cmd(floppy, pc, rq, block);
} else if (rq->flags & REQ_SPECIAL) {
pc = (idefloppy_pc_t *) rq->buffer;
} else if (rq->flags & REQ_BLOCK_PC) {
pc = idefloppy_next_pc_storage(drive);
if (idefloppy_blockpc_cmd(floppy, pc, rq)) {
idefloppy_do_end_request(drive, 0, 0);
return ide_stopped;
}
} else {
blk_dump_rq_flags(rq,
"ide-floppy: unsupported command in queue");
idefloppy_do_end_request(drive, 0, 0);
return ide_stopped;
}
pc->rq = rq;
return idefloppy_issue_pc(drive, pc);
}
/*
* idefloppy_queue_pc_tail adds a special packet command request to the
* tail of the request queue, and waits for it to be serviced.
*/
static int idefloppy_queue_pc_tail (ide_drive_t *drive,idefloppy_pc_t *pc)
{
struct ide_floppy_obj *floppy = drive->driver_data;
struct request rq;
ide_init_drive_cmd (&rq);
rq.buffer = (char *) pc;
rq.flags = REQ_SPECIAL; // rq.cmd = IDEFLOPPY_PC_RQ;
rq.rq_disk = floppy->disk;
return ide_do_drive_cmd(drive, &rq, ide_wait);
}
/*
* Look at the flexible disk page parameters. We will ignore the CHS
* capacity parameters and use the LBA parameters instead.
*/
static int idefloppy_get_flexible_disk_page (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
idefloppy_pc_t pc;
idefloppy_mode_parameter_header_t *header;
idefloppy_flexible_disk_page_t *page;
int capacity, lba_capacity;
idefloppy_create_mode_sense_cmd(&pc, IDEFLOPPY_FLEXIBLE_DISK_PAGE, MODE_SENSE_CURRENT);
if (idefloppy_queue_pc_tail(drive,&pc)) {
printk(KERN_ERR "ide-floppy: Can't get flexible disk "
"page parameters\n");
return 1;
}
header = (idefloppy_mode_parameter_header_t *) pc.buffer;
floppy->wp = header->wp;
set_disk_ro(floppy->disk, floppy->wp);
page = (idefloppy_flexible_disk_page_t *) (header + 1);
page->transfer_rate = ntohs(page->transfer_rate);
page->sector_size = ntohs(page->sector_size);
page->cyls = ntohs(page->cyls);
page->rpm = ntohs(page->rpm);
capacity = page->cyls * page->heads * page->sectors * page->sector_size;
if (memcmp (page, &floppy->flexible_disk_page, sizeof (idefloppy_flexible_disk_page_t)))
printk(KERN_INFO "%s: %dkB, %d/%d/%d CHS, %d kBps, "
"%d sector size, %d rpm\n",
drive->name, capacity / 1024, page->cyls,
page->heads, page->sectors,
page->transfer_rate / 8, page->sector_size, page->rpm);
floppy->flexible_disk_page = *page;
drive->bios_cyl = page->cyls;
drive->bios_head = page->heads;
drive->bios_sect = page->sectors;
lba_capacity = floppy->blocks * floppy->block_size;
if (capacity < lba_capacity) {
printk(KERN_NOTICE "%s: The disk reports a capacity of %d "
"bytes, but the drive only handles %d\n",
drive->name, lba_capacity, capacity);
floppy->blocks = floppy->block_size ? capacity / floppy->block_size : 0;
}
return 0;
}
static int idefloppy_get_capability_page(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
idefloppy_pc_t pc;
idefloppy_mode_parameter_header_t *header;
idefloppy_capabilities_page_t *page;
floppy->srfp = 0;
idefloppy_create_mode_sense_cmd(&pc, IDEFLOPPY_CAPABILITIES_PAGE,
MODE_SENSE_CURRENT);
set_bit(PC_SUPPRESS_ERROR, &pc.flags);
if (idefloppy_queue_pc_tail(drive,&pc)) {
return 1;
}
header = (idefloppy_mode_parameter_header_t *) pc.buffer;
page= (idefloppy_capabilities_page_t *)(header+1);
floppy->srfp = page->srfp;
return (0);
}
/*
* Determine if a media is present in the floppy drive, and if so,
* its LBA capacity.
*/
static int idefloppy_get_capacity (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
idefloppy_pc_t pc;
idefloppy_capacity_header_t *header;
idefloppy_capacity_descriptor_t *descriptor;
int i, descriptors, rc = 1, blocks, length;
drive->bios_cyl = 0;
drive->bios_head = drive->bios_sect = 0;
floppy->blocks = floppy->bs_factor = 0;
set_capacity(floppy->disk, 0);
idefloppy_create_read_capacity_cmd(&pc);
if (idefloppy_queue_pc_tail(drive, &pc)) {
printk(KERN_ERR "ide-floppy: Can't get floppy parameters\n");
return 1;
}
header = (idefloppy_capacity_header_t *) pc.buffer;
descriptors = header->length / sizeof(idefloppy_capacity_descriptor_t);
descriptor = (idefloppy_capacity_descriptor_t *) (header + 1);
for (i = 0; i < descriptors; i++, descriptor++) {
blocks = descriptor->blocks = ntohl(descriptor->blocks);
length = descriptor->length = ntohs(descriptor->length);
if (!i)
{
switch (descriptor->dc) {
/* Clik! drive returns this instead of CAPACITY_CURRENT */
case CAPACITY_UNFORMATTED:
if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags))
/*
* If it is not a clik drive, break out
* (maintains previous driver behaviour)
*/
break;
case CAPACITY_CURRENT:
/* Normal Zip/LS-120 disks */
if (memcmp(descriptor, &floppy->capacity, sizeof (idefloppy_capacity_descriptor_t)))
printk(KERN_INFO "%s: %dkB, %d blocks, %d "
"sector size\n", drive->name,
blocks * length / 1024, blocks, length);
floppy->capacity = *descriptor;
if (!length || length % 512) {
printk(KERN_NOTICE "%s: %d bytes block size "
"not supported\n", drive->name, length);
} else {
floppy->blocks = blocks;
floppy->block_size = length;
if ((floppy->bs_factor = length / 512) != 1)
printk(KERN_NOTICE "%s: warning: non "
"512 bytes block size not "
"fully supported\n",
drive->name);
rc = 0;
}
break;
case CAPACITY_NO_CARTRIDGE:
/*
* This is a KERN_ERR so it appears on screen
* for the user to see
*/
printk(KERN_ERR "%s: No disk in drive\n", drive->name);
break;
case CAPACITY_INVALID:
printk(KERN_ERR "%s: Invalid capacity for disk "
"in drive\n", drive->name);
break;
}
}
if (!i) {
debug_log( "Descriptor 0 Code: %d\n",
descriptor->dc);
}
debug_log( "Descriptor %d: %dkB, %d blocks, %d "
"sector size\n", i, blocks * length / 1024, blocks,
length);
}
/* Clik! disk does not support get_flexible_disk_page */
if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
(void) idefloppy_get_flexible_disk_page(drive);
}
set_capacity(floppy->disk, floppy->blocks * floppy->bs_factor);
return rc;
}
/*
** Obtain the list of formattable capacities.
** Very similar to idefloppy_get_capacity, except that we push the capacity
** descriptors to userland, instead of our own structures.
**
** Userland gives us the following structure:
**
** struct idefloppy_format_capacities {
** int nformats;
** struct {
** int nblocks;
** int blocksize;
** } formats[];
** } ;
**
** userland initializes nformats to the number of allocated formats[]
** records. On exit we set nformats to the number of records we've
** actually initialized.
**
*/
static int idefloppy_get_format_capacities(ide_drive_t *drive, int __user *arg)
{
idefloppy_pc_t pc;
idefloppy_capacity_header_t *header;
idefloppy_capacity_descriptor_t *descriptor;
int i, descriptors, blocks, length;
int u_array_size;
int u_index;
int __user *argp;
if (get_user(u_array_size, arg))
return (-EFAULT);
if (u_array_size <= 0)
return (-EINVAL);
idefloppy_create_read_capacity_cmd(&pc);
if (idefloppy_queue_pc_tail(drive, &pc)) {
printk(KERN_ERR "ide-floppy: Can't get floppy parameters\n");
return (-EIO);
}
header = (idefloppy_capacity_header_t *) pc.buffer;
descriptors = header->length /
sizeof(idefloppy_capacity_descriptor_t);
descriptor = (idefloppy_capacity_descriptor_t *) (header + 1);
u_index = 0;
argp = arg + 1;
/*
** We always skip the first capacity descriptor. That's the
** current capacity. We are interested in the remaining descriptors,
** the formattable capacities.
*/
for (i=0; i<descriptors; i++, descriptor++) {
if (u_index >= u_array_size)
break; /* User-supplied buffer too small */
if (i == 0)
continue; /* Skip the first descriptor */
blocks = ntohl(descriptor->blocks);
length = ntohs(descriptor->length);
if (put_user(blocks, argp))
return(-EFAULT);
++argp;
if (put_user(length, argp))
return (-EFAULT);
++argp;
++u_index;
}
if (put_user(u_index, arg))
return (-EFAULT);
return (0);
}
/*
** Send ATAPI_FORMAT_UNIT to the drive.
**
** Userland gives us the following structure:
**
** struct idefloppy_format_command {
** int nblocks;
** int blocksize;
** int flags;
** } ;
**
** flags is a bitmask, currently, the only defined flag is:
**
** 0x01 - verify media after format.
*/
static int idefloppy_begin_format(ide_drive_t *drive, int __user *arg)
{
int blocks;
int length;
int flags;
idefloppy_pc_t pc;
if (get_user(blocks, arg) ||
get_user(length, arg+1) ||
get_user(flags, arg+2)) {
return (-EFAULT);
}
/* Get the SFRP bit */
(void) idefloppy_get_capability_page(drive);
idefloppy_create_format_unit_cmd(&pc, blocks, length, flags);
if (idefloppy_queue_pc_tail(drive, &pc)) {
return (-EIO);
}
return (0);
}
/*
** Get ATAPI_FORMAT_UNIT progress indication.
**
** Userland gives a pointer to an int. The int is set to a progresss
** indicator 0-65536, with 65536=100%.
**
** If the drive does not support format progress indication, we just check
** the dsc bit, and return either 0 or 65536.
*/
static int idefloppy_get_format_progress(ide_drive_t *drive, int __user *arg)
{
idefloppy_floppy_t *floppy = drive->driver_data;
idefloppy_pc_t pc;
int progress_indication = 0x10000;
if (floppy->srfp) {
idefloppy_create_request_sense_cmd(&pc);
if (idefloppy_queue_pc_tail(drive, &pc)) {
return (-EIO);
}
if (floppy->sense_key == 2 &&
floppy->asc == 4 &&
floppy->ascq == 4) {
progress_indication = floppy->progress_indication;
}
/* Else assume format_unit has finished, and we're
** at 0x10000 */
} else {
atapi_status_t status;
unsigned long flags;
local_irq_save(flags);
status.all = HWIF(drive)->INB(IDE_STATUS_REG);
local_irq_restore(flags);
progress_indication = !status.b.dsc ? 0 : 0x10000;
}
if (put_user(progress_indication, arg))
return (-EFAULT);
return (0);
}
/*
* Return the current floppy capacity.
*/
static sector_t idefloppy_capacity (ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
unsigned long capacity = floppy->blocks * floppy->bs_factor;
return capacity;
}
/*
* idefloppy_identify_device checks if we can support a drive,
* based on the ATAPI IDENTIFY command results.
*/
static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
{
struct idefloppy_id_gcw gcw;
#if IDEFLOPPY_DEBUG_INFO
u16 mask,i;
char buffer[80];
#endif /* IDEFLOPPY_DEBUG_INFO */
*((u16 *) &gcw) = id->config;
#ifdef CONFIG_PPC
/* kludge for Apple PowerBook internal zip */
if ((gcw.device_type == 5) &&
!strstr(id->model, "CD-ROM") &&
strstr(id->model, "ZIP"))
gcw.device_type = 0;
#endif
#if IDEFLOPPY_DEBUG_INFO
printk(KERN_INFO "Dumping ATAPI Identify Device floppy parameters\n");
switch (gcw.protocol) {
case 0: case 1: sprintf(buffer, "ATA");break;
case 2: sprintf(buffer, "ATAPI");break;
case 3: sprintf(buffer, "Reserved (Unknown to ide-floppy)");break;
}
printk(KERN_INFO "Protocol Type: %s\n", buffer);
switch (gcw.device_type) {
case 0: sprintf(buffer, "Direct-access Device");break;
case 1: sprintf(buffer, "Streaming Tape Device");break;
case 2: case 3: case 4: sprintf (buffer, "Reserved");break;
case 5: sprintf(buffer, "CD-ROM Device");break;
case 6: sprintf(buffer, "Reserved");
case 7: sprintf(buffer, "Optical memory Device");break;
case 0x1f: sprintf(buffer, "Unknown or no Device type");break;
default: sprintf(buffer, "Reserved");
}
printk(KERN_INFO "Device Type: %x - %s\n", gcw.device_type, buffer);
printk(KERN_INFO "Removable: %s\n",gcw.removable ? "Yes":"No");
switch (gcw.drq_type) {
case 0: sprintf(buffer, "Microprocessor DRQ");break;
case 1: sprintf(buffer, "Interrupt DRQ");break;
case 2: sprintf(buffer, "Accelerated DRQ");break;
case 3: sprintf(buffer, "Reserved");break;
}
printk(KERN_INFO "Command Packet DRQ Type: %s\n", buffer);
switch (gcw.packet_size) {
case 0: sprintf(buffer, "12 bytes");break;
case 1: sprintf(buffer, "16 bytes");break;
default: sprintf(buffer, "Reserved");break;
}
printk(KERN_INFO "Command Packet Size: %s\n", buffer);
printk(KERN_INFO "Model: %.40s\n",id->model);
printk(KERN_INFO "Firmware Revision: %.8s\n",id->fw_rev);
printk(KERN_INFO "Serial Number: %.20s\n",id->serial_no);
printk(KERN_INFO "Write buffer size(?): %d bytes\n",id->buf_size*512);
printk(KERN_INFO "DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
printk(KERN_INFO "LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
printk(KERN_INFO "IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
printk(KERN_INFO "IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
printk(KERN_INFO "ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
printk(KERN_INFO "PIO Cycle Timing Category: %d\n",id->tPIO);
printk(KERN_INFO "DMA Cycle Timing Category: %d\n",id->tDMA);
printk(KERN_INFO "Single Word DMA supported modes:\n");
for (i=0,mask=1;i<8;i++,mask=mask << 1) {
if (id->dma_1word & mask)
printk(KERN_INFO " Mode %d%s\n", i,
(id->dma_1word & (mask << 8)) ? " (active)" : "");
}
printk(KERN_INFO "Multi Word DMA supported modes:\n");
for (i=0,mask=1;i<8;i++,mask=mask << 1) {
if (id->dma_mword & mask)
printk(KERN_INFO " Mode %d%s\n", i,
(id->dma_mword & (mask << 8)) ? " (active)" : "");
}
if (id->field_valid & 0x0002) {
printk(KERN_INFO "Enhanced PIO Modes: %s\n",
id->eide_pio_modes & 1 ? "Mode 3":"None");
if (id->eide_dma_min == 0)
sprintf(buffer, "Not supported");
else
sprintf(buffer, "%d ns",id->eide_dma_min);
printk(KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n", buffer);
if (id->eide_dma_time == 0)
sprintf(buffer, "Not supported");
else
sprintf(buffer, "%d ns",id->eide_dma_time);
printk(KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n", buffer);
if (id->eide_pio == 0)
sprintf(buffer, "Not supported");
else
sprintf(buffer, "%d ns",id->eide_pio);
printk(KERN_INFO "Minimum PIO cycle without IORDY: %s\n",
buffer);
if (id->eide_pio_iordy == 0)
sprintf(buffer, "Not supported");
else
sprintf(buffer, "%d ns",id->eide_pio_iordy);
printk(KERN_INFO "Minimum PIO cycle with IORDY: %s\n", buffer);
} else
printk(KERN_INFO "According to the device, fields 64-70 are not valid.\n");
#endif /* IDEFLOPPY_DEBUG_INFO */
if (gcw.protocol != 2)
printk(KERN_ERR "ide-floppy: Protocol is not ATAPI\n");
else if (gcw.device_type != 0)
printk(KERN_ERR "ide-floppy: Device type is not set to floppy\n");
else if (!gcw.removable)
printk(KERN_ERR "ide-floppy: The removable flag is not set\n");
else if (gcw.drq_type == 3) {
printk(KERN_ERR "ide-floppy: Sorry, DRQ type %d not supported\n", gcw.drq_type);
} else if (gcw.packet_size != 0) {
printk(KERN_ERR "ide-floppy: Packet size is not 12 bytes long\n");
} else
return 1;
return 0;
}
static void idefloppy_add_settings(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
/*
* drive setting name read/write ioctl ioctl data type min max mul_factor div_factor data pointer set function
*/
ide_add_setting(drive, "bios_cyl", SETTING_RW, -1, -1, TYPE_INT, 0, 1023, 1, 1, &drive->bios_cyl, NULL);
ide_add_setting(drive, "bios_head", SETTING_RW, -1, -1, TYPE_BYTE, 0, 255, 1, 1, &drive->bios_head, NULL);
ide_add_setting(drive, "bios_sect", SETTING_RW, -1, -1, TYPE_BYTE, 0, 63, 1, 1, &drive->bios_sect, NULL);
ide_add_setting(drive, "ticks", SETTING_RW, -1, -1, TYPE_BYTE, 0, 255, 1, 1, &floppy->ticks, NULL);
}
/*
* Driver initialization.
*/
static void idefloppy_setup (ide_drive_t *drive, idefloppy_floppy_t *floppy)
{
struct idefloppy_id_gcw gcw;
*((u16 *) &gcw) = drive->id->config;
floppy->pc = floppy->pc_stack;
if (gcw.drq_type == 1)
set_bit(IDEFLOPPY_DRQ_INTERRUPT, &floppy->flags);
/*
* We used to check revisions here. At this point however
* I'm giving up. Just assume they are all broken, its easier.
*
* The actual reason for the workarounds was likely
* a driver bug after all rather than a firmware bug,
* and the workaround below used to hide it. It should
* be fixed as of version 1.9, but to be on the safe side
* we'll leave the limitation below for the 2.2.x tree.
*/
if (!strncmp(drive->id->model, "IOMEGA ZIP 100 ATAPI", 20)) {
set_bit(IDEFLOPPY_ZIP_DRIVE, &floppy->flags);
/* This value will be visible in the /proc/ide/hdx/settings */
floppy->ticks = IDEFLOPPY_TICKS_DELAY;
blk_queue_max_sectors(drive->queue, 64);
}
/*
* Guess what? The IOMEGA Clik! drive also needs the
* above fix. It makes nasty clicking noises without
* it, so please don't remove this.
*/
if (strncmp(drive->id->model, "IOMEGA Clik!", 11) == 0) {
blk_queue_max_sectors(drive->queue, 64);
set_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags);
}
(void) idefloppy_get_capacity(drive);
idefloppy_add_settings(drive);
}
static void ide_floppy_remove(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
struct gendisk *g = floppy->disk;
ide_unregister_subdriver(drive, floppy->driver);
del_gendisk(g);
ide_floppy_put(floppy);
}
static void ide_floppy_release(struct kref *kref)
{
struct ide_floppy_obj *floppy = to_ide_floppy(kref);
ide_drive_t *drive = floppy->drive;
struct gendisk *g = floppy->disk;
drive->driver_data = NULL;
g->private_data = NULL;
put_disk(g);
kfree(floppy);
}
#ifdef CONFIG_PROC_FS
static int proc_idefloppy_read_capacity
(char *page, char **start, off_t off, int count, int *eof, void *data)
{
ide_drive_t*drive = (ide_drive_t *)data;
int len;
len = sprintf(page,"%llu\n", (long long)idefloppy_capacity(drive));
PROC_IDE_READ_RETURN(page,start,off,count,eof,len);
}
static ide_proc_entry_t idefloppy_proc[] = {
{ "capacity", S_IFREG|S_IRUGO, proc_idefloppy_read_capacity, NULL },
{ "geometry", S_IFREG|S_IRUGO, proc_ide_read_geometry, NULL },
{ NULL, 0, NULL, NULL }
};
#else
#define idefloppy_proc NULL
#endif /* CONFIG_PROC_FS */
static int ide_floppy_probe(ide_drive_t *);
static ide_driver_t idefloppy_driver = {
.gen_driver = {
.owner = THIS_MODULE,
.name = "ide-floppy",
.bus = &ide_bus_type,
},
.probe = ide_floppy_probe,
.remove = ide_floppy_remove,
.version = IDEFLOPPY_VERSION,
.media = ide_floppy,
.supports_dsc_overlap = 0,
.do_request = idefloppy_do_request,
.end_request = idefloppy_do_end_request,
.error = __ide_error,
.abort = __ide_abort,
.proc = idefloppy_proc,
};
static int idefloppy_open(struct inode *inode, struct file *filp)
{
struct gendisk *disk = inode->i_bdev->bd_disk;
struct ide_floppy_obj *floppy;
ide_drive_t *drive;
idefloppy_pc_t pc;
int ret = 0;
debug_log(KERN_INFO "Reached idefloppy_open\n");
if (!(floppy = ide_floppy_get(disk)))
return -ENXIO;
drive = floppy->drive;
drive->usage++;
if (drive->usage == 1) {
clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
/* Just in case */
idefloppy_create_test_unit_ready_cmd(&pc);
if (idefloppy_queue_pc_tail(drive, &pc)) {
idefloppy_create_start_stop_cmd(&pc, 1);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
if (idefloppy_get_capacity (drive)
&& (filp->f_flags & O_NDELAY) == 0
/*
** Allow O_NDELAY to open a drive without a disk, or with
** an unreadable disk, so that we can get the format
** capacity of the drive or begin the format - Sam
*/
) {
drive->usage--;
ret = -EIO;
goto out_put_floppy;
}
if (floppy->wp && (filp->f_mode & 2)) {
drive->usage--;
ret = -EROFS;
goto out_put_floppy;
}
set_bit(IDEFLOPPY_MEDIA_CHANGED, &floppy->flags);
/* IOMEGA Clik! drives do not support lock/unlock commands */
if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
idefloppy_create_prevent_cmd(&pc, 1);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
check_disk_change(inode->i_bdev);
} else if (test_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags)) {
drive->usage--;
ret = -EBUSY;
goto out_put_floppy;
}
return 0;
out_put_floppy:
ide_floppy_put(floppy);
return ret;
}
static int idefloppy_release(struct inode *inode, struct file *filp)
{
struct gendisk *disk = inode->i_bdev->bd_disk;
struct ide_floppy_obj *floppy = ide_floppy_g(disk);
ide_drive_t *drive = floppy->drive;
idefloppy_pc_t pc;
debug_log(KERN_INFO "Reached idefloppy_release\n");
if (drive->usage == 1) {
/* IOMEGA Clik! drives do not support lock/unlock commands */
if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
idefloppy_create_prevent_cmd(&pc, 0);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
}
drive->usage--;
ide_floppy_put(floppy);
return 0;
}
static int idefloppy_getgeo(struct block_device *bdev, struct hd_geometry *geo)
{
struct ide_floppy_obj *floppy = ide_floppy_g(bdev->bd_disk);
ide_drive_t *drive = floppy->drive;
geo->heads = drive->bios_head;
geo->sectors = drive->bios_sect;
geo->cylinders = (u16)drive->bios_cyl; /* truncate */
return 0;
}
static int idefloppy_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
struct block_device *bdev = inode->i_bdev;
struct ide_floppy_obj *floppy = ide_floppy_g(bdev->bd_disk);
ide_drive_t *drive = floppy->drive;
void __user *argp = (void __user *)arg;
int err;
int prevent = (arg) ? 1 : 0;
idefloppy_pc_t pc;
switch (cmd) {
case CDROMEJECT:
prevent = 0;
/* fall through */
case CDROM_LOCKDOOR:
if (drive->usage > 1)
return -EBUSY;
/* The IOMEGA Clik! Drive doesn't support this command - no room for an eject mechanism */
if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
idefloppy_create_prevent_cmd(&pc, prevent);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
if (cmd == CDROMEJECT) {
idefloppy_create_start_stop_cmd(&pc, 2);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
return 0;
case IDEFLOPPY_IOCTL_FORMAT_SUPPORTED:
return 0;
case IDEFLOPPY_IOCTL_FORMAT_GET_CAPACITY:
return idefloppy_get_format_capacities(drive, argp);
case IDEFLOPPY_IOCTL_FORMAT_START:
if (!(file->f_mode & 2))
return -EPERM;
if (drive->usage > 1) {
/* Don't format if someone is using the disk */
clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS,
&floppy->flags);
return -EBUSY;
}
set_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
err = idefloppy_begin_format(drive, argp);
if (err)
clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
return err;
/*
** Note, the bit will be cleared when the device is
** closed. This is the cleanest way to handle the
** situation where the drive does not support
** format progress reporting.
*/
case IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS:
return idefloppy_get_format_progress(drive, argp);
}
return generic_ide_ioctl(drive, file, bdev, cmd, arg);
}
static int idefloppy_media_changed(struct gendisk *disk)
{
struct ide_floppy_obj *floppy = ide_floppy_g(disk);
ide_drive_t *drive = floppy->drive;
/* do not scan partitions twice if this is a removable device */
if (drive->attach) {
drive->attach = 0;
return 0;
}
return test_and_clear_bit(IDEFLOPPY_MEDIA_CHANGED, &floppy->flags);
}
static int idefloppy_revalidate_disk(struct gendisk *disk)
{
struct ide_floppy_obj *floppy = ide_floppy_g(disk);
set_capacity(disk, idefloppy_capacity(floppy->drive));
return 0;
}
static struct block_device_operations idefloppy_ops = {
.owner = THIS_MODULE,
.open = idefloppy_open,
.release = idefloppy_release,
.ioctl = idefloppy_ioctl,
.getgeo = idefloppy_getgeo,
.media_changed = idefloppy_media_changed,
.revalidate_disk= idefloppy_revalidate_disk
};
static int ide_floppy_probe(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy;
struct gendisk *g;
if (!strstr("ide-floppy", drive->driver_req))
goto failed;
if (!drive->present)
goto failed;
if (drive->media != ide_floppy)
goto failed;
if (!idefloppy_identify_device (drive, drive->id)) {
printk (KERN_ERR "ide-floppy: %s: not supported by this version of ide-floppy\n", drive->name);
goto failed;
}
if (drive->scsi) {
printk("ide-floppy: passing drive %s to ide-scsi emulation.\n", drive->name);
goto failed;
}
if ((floppy = (idefloppy_floppy_t *) kzalloc (sizeof (idefloppy_floppy_t), GFP_KERNEL)) == NULL) {
printk (KERN_ERR "ide-floppy: %s: Can't allocate a floppy structure\n", drive->name);
goto failed;
}
g = alloc_disk(1 << PARTN_BITS);
if (!g)
goto out_free_floppy;
ide_init_disk(g, drive);
ide_register_subdriver(drive, &idefloppy_driver);
kref_init(&floppy->kref);
floppy->drive = drive;
floppy->driver = &idefloppy_driver;
floppy->disk = g;
g->private_data = &floppy->driver;
drive->driver_data = floppy;
idefloppy_setup (drive, floppy);
g->minors = 1 << PARTN_BITS;
g->driverfs_dev = &drive->gendev;
strcpy(g->devfs_name, drive->devfs_name);
g->flags = drive->removable ? GENHD_FL_REMOVABLE : 0;
g->fops = &idefloppy_ops;
drive->attach = 1;
add_disk(g);
return 0;
out_free_floppy:
kfree(floppy);
failed:
return -ENODEV;
}
MODULE_DESCRIPTION("ATAPI FLOPPY Driver");
static void __exit idefloppy_exit (void)
{
driver_unregister(&idefloppy_driver.gen_driver);
}
static int __init idefloppy_init(void)
{
printk("ide-floppy driver " IDEFLOPPY_VERSION "\n");
return driver_register(&idefloppy_driver.gen_driver);
}
MODULE_ALIAS("ide:*m-floppy*");
module_init(idefloppy_init);
module_exit(idefloppy_exit);
MODULE_LICENSE("GPL");
