/*
* Freescale CPM1/CPM2 I2C interface.
* Copyright (c) 1999 Dan Malek (dmalek@jlc.net).
*
* moved into proper i2c interface;
* Brad Parker (brad@heeltoe.com)
*
* Parts from dbox2_i2c.c (cvs.tuxbox.org)
* (C) 2000-2001 Felix Domke (tmbinc@gmx.net), Gillem (htoa@gmx.net)
*
* (C) 2007 Montavista Software, Inc.
* Vitaly Bordug <vitb@kernel.crashing.org>
*
* Converted to of_platform_device. Renamed to i2c-cpm.c.
* (C) 2007,2008 Jochen Friedrich <jochen@scram.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/stddef.h>
#include <linux/i2c.h>
#include <linux/io.h>
#include <linux/dma-mapping.h>
#include <linux/of_device.h>
#include <linux/of_platform.h>
#include <linux/of_i2c.h>
#include <sysdev/fsl_soc.h>
#include <asm/cpm.h>
/* Try to define this if you have an older CPU (earlier than rev D4) */
/* However, better use a GPIO based bitbang driver in this case :/ */
#undef I2C_CHIP_ERRATA
#define CPM_MAX_READ 513
#define CPM_MAXBD 4
#define I2C_EB (0x10) /* Big endian mode */
#define I2C_EB_CPM2 (0x30) /* Big endian mode, memory snoop */
#define DPRAM_BASE ((u8 __iomem __force *)cpm_muram_addr(0))
/* I2C parameter RAM. */
struct i2c_ram {
ushort rbase; /* Rx Buffer descriptor base address */
ushort tbase; /* Tx Buffer descriptor base address */
u_char rfcr; /* Rx function code */
u_char tfcr; /* Tx function code */
ushort mrblr; /* Max receive buffer length */
uint rstate; /* Internal */
uint rdp; /* Internal */
ushort rbptr; /* Rx Buffer descriptor pointer */
ushort rbc; /* Internal */
uint rxtmp; /* Internal */
uint tstate; /* Internal */
uint tdp; /* Internal */
ushort tbptr; /* Tx Buffer descriptor pointer */
ushort tbc; /* Internal */
uint txtmp; /* Internal */
char res1[4]; /* Reserved */
ushort rpbase; /* Relocation pointer */
char res2[2]; /* Reserved */
};
#define I2COM_START 0x80
#define I2COM_MASTER 0x01
#define I2CER_TXE 0x10
#define I2CER_BUSY 0x04
#define I2CER_TXB 0x02
#define I2CER_RXB 0x01
#define I2MOD_EN 0x01
/* I2C Registers */
struct i2c_reg {
u8 i2mod;
u8 res1[3];
u8 i2add;
u8 res2[3];
u8 i2brg;
u8 res3[3];
u8 i2com;
u8 res4[3];
u8 i2cer;
u8 res5[3];
u8 i2cmr;
};
struct cpm_i2c {
char *base;
struct of_device *ofdev;
struct i2c_adapter adap;
uint dp_addr;
int version; /* CPM1=1, CPM2=2 */
int irq;
int cp_command;
int freq;
struct i2c_reg __iomem *i2c_reg;
struct i2c_ram __iomem *i2c_ram;
u16 i2c_addr;
wait_queue_head_t i2c_wait;
cbd_t __iomem *tbase;
cbd_t __iomem *rbase;
u_char *txbuf[CPM_MAXBD];
u_char *rxbuf[CPM_MAXBD];
u32 txdma[CPM_MAXBD];
u32 rxdma[CPM_MAXBD];
};
static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id)
{
struct cpm_i2c *cpm;
struct i2c_reg __iomem *i2c_reg;
struct i2c_adapter *adap = dev_id;
int i;
cpm = i2c_get_adapdata(dev_id);
i2c_reg = cpm->i2c_reg;
/* Clear interrupt. */
i = in_8(&i2c_reg->i2cer);
out_8(&i2c_reg->i2cer, i);
dev_dbg(&adap->dev, "Interrupt: %x\n", i);
wake_up_interruptible(&cpm->i2c_wait);
return i ? IRQ_HANDLED : IRQ_NONE;
}
static void cpm_reset_i2c_params(struct cpm_i2c *cpm)
{
struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
/* Set up the I2C parameters in the parameter ram. */
out_be16(&i2c_ram->tbase, (u8 __iomem *)cpm->tbase - DPRAM_BASE);
out_be16(&i2c_ram->rbase, (u8 __iomem *)cpm->rbase - DPRAM_BASE);
if (cpm->version == 1) {
out_8(&i2c_ram->tfcr, I2C_EB);
out_8(&i2c_ram->rfcr, I2C_EB);
} else {
out_8(&i2c_ram->tfcr, I2C_EB_CPM2);
out_8(&i2c_ram->rfcr, I2C_EB_CPM2);
}
out_be16(&i2c_ram->mrblr, CPM_MAX_READ);
out_be32(&i2c_ram->rstate, 0);
out_be32(&i2c_ram->rdp, 0);
out_be16(&i2c_ram->rbptr, 0);
out_be16(&i2c_ram->rbc, 0);
out_be32(&i2c_ram->rxtmp, 0);
out_be32(&i2c_ram->tstate, 0);
out_be32(&i2c_ram->tdp, 0);
out_be16(&i2c_ram->tbptr, 0);
out_be16(&i2c_ram->tbc, 0);
out_be32(&i2c_ram->txtmp, 0);
}
static void cpm_i2c_force_close(struct i2c_adapter *adap)
{
struct cpm_i2c *cpm = i2c_get_adapdata(adap);
struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
dev_dbg(&adap->dev, "cpm_i2c_force_close()\n");
cpm_command(cpm->cp_command, CPM_CR_CLOSE_RX_BD);
out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */
out_8(&i2c_reg->i2cer, 0xff);
}
static void cpm_i2c_parse_message(struct i2c_adapter *adap,
struct i2c_msg *pmsg, int num, int tx, int rx)
{
cbd_t __iomem *tbdf;
cbd_t __iomem *rbdf;
u_char addr;
u_char *tb;
u_char *rb;
struct cpm_i2c *cpm = i2c_get_adapdata(adap);
tbdf = cpm->tbase + tx;
rbdf = cpm->rbase + rx;
addr = pmsg->addr << 1;
if (pmsg->flags & I2C_M_RD)
addr |= 1;
tb = cpm->txbuf[tx];
rb = cpm->rxbuf[rx];
/* Align read buffer */
rb = (u_char *) (((ulong) rb + 1) & ~1);
tb[0] = addr; /* Device address byte w/rw flag */
out_be16(&tbdf->cbd_datlen, pmsg->len + 1);
out_be16(&tbdf->cbd_sc, 0);
if (!(pmsg->flags & I2C_M_NOSTART))
setbits16(&tbdf->cbd_sc, BD_I2C_START);
if (tx + 1 == num)
setbits16(&tbdf->cbd_sc, BD_SC_LAST | BD_SC_WRAP);
if (pmsg->flags & I2C_M_RD) {
/*
* To read, we need an empty buffer of the proper length.
* All that is used is the first byte for address, the remainder
* is just used for timing (and doesn't really have to exist).
*/
dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr);
out_be16(&rbdf->cbd_datlen, 0);
out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT);
if (rx + 1 == CPM_MAXBD)
setbits16(&rbdf->cbd_sc, BD_SC_WRAP);
eieio();
setbits16(&tbdf->cbd_sc, BD_SC_READY);
} else {
dev_dbg(&adap->dev, "cpm_iic_write(abyte=0x%x)\n", addr);
memcpy(tb+1, pmsg->buf, pmsg->len);
eieio();
setbits16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_INTRPT);
}
}
static int cpm_i2c_check_message(struct i2c_adapter *adap,
struct i2c_msg *pmsg, int tx, int rx)
{
cbd_t __iomem *tbdf;
cbd_t __iomem *rbdf;
u_char *tb;
u_char *rb;
struct cpm_i2c *cpm = i2c_get_adapdata(adap);
tbdf = cpm->tbase + tx;
rbdf = cpm->rbase + rx;
tb = cpm->txbuf[tx];
rb = cpm->rxbuf[rx];
/* Align read buffer */
rb = (u_char *) (((uint) rb + 1) & ~1);
eieio();
if (pmsg->flags & I2C_M_RD) {
dev_dbg(&adap->dev, "tx sc 0x%04x, rx sc 0x%04x\n",
in_be16(&tbdf->cbd_sc), in_be16(&rbdf->cbd_sc));
if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) {
dev_dbg(&adap->dev, "I2C read; No ack\n");
return -ENXIO;
}
if (in_be16(&rbdf->cbd_sc) & BD_SC_EMPTY) {
dev_err(&adap->dev,
"I2C read; complete but rbuf empty\n");
return -EREMOTEIO;
}
if (in_be16(&rbdf->cbd_sc) & BD_SC_OV) {
dev_err(&adap->dev, "I2C read; Overrun\n");
return -EREMOTEIO;
}
memcpy(pmsg->buf, rb, pmsg->len);
} else {
dev_dbg(&adap->dev, "tx sc %d 0x%04x\n", tx,
in_be16(&tbdf->cbd_sc));
if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) {
dev_dbg(&adap->dev, "I2C write; No ack\n");
return -ENXIO;
}
if (in_be16(&tbdf->cbd_sc) & BD_SC_UN) {
dev_err(&adap->dev, "I2C write; Underrun\n");
return -EIO;
}
if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) {
dev_err(&adap->dev, "I2C write; Collision\n");
return -EIO;
}
}
return 0;
}
static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
struct cpm_i2c *cpm = i2c_get_adapdata(adap);
struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
struct i2c_msg *pmsg;
int ret, i;
int tptr;
int rptr;
cbd_t __iomem *tbdf;
cbd_t __iomem *rbdf;
if (num > CPM_MAXBD)
return -EINVAL;
/* Check if we have any oversized READ requests */
for (i = 0; i < num; i++) {
pmsg = &msgs[i];
if (pmsg->len >= CPM_MAX_READ)
return -EINVAL;
}
/* Reset to use first buffer */
out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase));
out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase));
tbdf = cpm->tbase;
rbdf = cpm->rbase;
tptr = 0;
rptr = 0;
while (tptr < num) {
pmsg = &msgs[tptr];
dev_dbg(&adap->dev, "R: %d T: %d\n", rptr, tptr);
cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr);
if (pmsg->flags & I2C_M_RD)
rptr++;
tptr++;
}
/* Start transfer now */
/* Enable RX/TX/Error interupts */
out_8(&i2c_reg->i2cmr, I2CER_BUSY | I2CER_TXB | I2CER_RXB);
out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */
/* Chip bug, set enable here */
setbits8(&i2c_reg->i2mod, I2MOD_EN); /* Enable */
/* Begin transmission */
setbits8(&i2c_reg->i2com, I2COM_START);
tptr = 0;
rptr = 0;
while (tptr < num) {
/* Check for outstanding messages */
dev_dbg(&adap->dev, "test ready.\n");
pmsg = &msgs[tptr];
if (pmsg->flags & I2C_M_RD)
ret = wait_event_interruptible_timeout(cpm->i2c_wait,
!(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY),
1 * HZ);
else
ret = wait_event_interruptible_timeout(cpm->i2c_wait,
!(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_READY),
1 * HZ);
if (ret == 0) {
ret = -EREMOTEIO;
dev_err(&adap->dev, "I2C transfer: timeout\n");
goto out_err;
}
if (ret > 0) {
dev_dbg(&adap->dev, "ready.\n");
ret = cpm_i2c_check_message(adap, pmsg, tptr, rptr);
tptr++;
if (pmsg->flags & I2C_M_RD)
rptr++;
if (ret)
goto out_err;
}
}
#ifdef I2C_CHIP_ERRATA
/*
* Chip errata, clear enable. This is not needed on rev D4 CPUs.
* Disabling I2C too early may cause too short stop condition
*/
udelay(4);
clrbits8(&i2c_reg->i2mod, I2MOD_EN);
#endif
return (num);
out_err:
cpm_i2c_force_close(adap);
#ifdef I2C_CHIP_ERRATA
/*
* Chip errata, clear enable. This is not needed on rev D4 CPUs.
*/
clrbits8(&i2c_reg->i2mod, I2MOD_EN);
#endif
return ret;
}
static u32 cpm_i2c_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
}
/* -----exported algorithm data: ------------------------------------- */
static const struct i2c_algorithm cpm_i2c_algo = {
.master_xfer = cpm_i2c_xfer,
.functionality = cpm_i2c_func,
};
static const struct i2c_adapter cpm_ops = {
.owner = THIS_MODULE,
.name = "i2c-cpm",
.algo = &cpm_i2c_algo,
.class = I2C_CLASS_HWMON,
};
static int __devinit cpm_i2c_setup(struct cpm_i2c *cpm)
{
struct of_device *ofdev = cpm->ofdev;
const u32 *data;
int len, ret, i;
void __iomem *i2c_base;
cbd_t __iomem *tbdf;
cbd_t __iomem *rbdf;
unsigned char brg;
dev_dbg(&cpm->ofdev->dev, "cpm_i2c_setup()\n");
init_waitqueue_head(&cpm->i2c_wait);
cpm->irq = of_irq_to_resource(ofdev->node, 0, NULL);
if (cpm->irq == NO_IRQ)
return -EINVAL;
/* Install interrupt handler. */
ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c",
&cpm->adap);
if (ret)
return ret;
/* I2C parameter RAM */
i2c_base = of_iomap(ofdev->node, 1);
if (i2c_base == NULL) {
ret = -EINVAL;
goto out_irq;
}
if (of_device_is_compatible(ofdev->node, "fsl,cpm1-i2c")) {
/* Check for and use a microcode relocation patch. */
cpm->i2c_ram = i2c_base;
cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase);
/*
* Maybe should use cpm_muram_alloc instead of hardcoding
* this in micropatch.c
*/
if (cpm->i2c_addr) {
cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
iounmap(i2c_base);
}
cpm->version = 1;
} else if (of_device_is_compatible(ofdev->node, "fsl,cpm2-i2c")) {
cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64);
cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
out_be16(i2c_base, cpm->i2c_addr);
iounmap(i2c_base);
cpm->version = 2;
} else {
iounmap(i2c_base);
ret = -EINVAL;
goto out_irq;
}
/* I2C control/status registers */
cpm->i2c_reg = of_iomap(ofdev->node, 0);
if (cpm->i2c_reg == NULL) {
ret = -EINVAL;
goto out_ram;
}
data = of_get_property(ofdev->node, "fsl,cpm-command", &len);
if (!data || len != 4) {
ret = -EINVAL;
goto out_reg;
}
cpm->cp_command = *data;
data = of_get_property(ofdev->node, "linux,i2c-class", &len);
if (data && len == 4)
cpm->adap.class = *data;
data = of_get_property(ofdev->node, "clock-frequency", &len);
if (data && len == 4)
cpm->freq = *data;
else
cpm->freq = 60000; /* use 60kHz i2c clock by default */
/*
* Allocate space for CPM_MAXBD transmit and receive buffer
* descriptors in the DP ram.
*/
cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8);
if (!cpm->dp_addr) {
ret = -ENOMEM;
goto out_reg;
}
cpm->tbase = cpm_muram_addr(cpm->dp_addr);
cpm->rbase = cpm_muram_addr(cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD);
/* Allocate TX and RX buffers */
tbdf = cpm->tbase;
rbdf = cpm->rbase;
for (i = 0; i < CPM_MAXBD; i++) {
cpm->rxbuf[i] = dma_alloc_coherent(
NULL, CPM_MAX_READ + 1, &cpm->rxdma[i], GFP_KERNEL);
if (!cpm->rxbuf[i]) {
ret = -ENOMEM;
goto out_muram;
}
out_be32(&rbdf[i].cbd_bufaddr, ((cpm->rxdma[i] + 1) & ~1));
cpm->txbuf[i] = (unsigned char *)dma_alloc_coherent(
NULL, CPM_MAX_READ + 1, &cpm->txdma[i], GFP_KERNEL);
if (!cpm->txbuf[i]) {
ret = -ENOMEM;
goto out_muram;
}
out_be32(&tbdf[i].cbd_bufaddr, cpm->txdma[i]);
}
/* Initialize Tx/Rx parameters. */
cpm_reset_i2c_params(cpm);
dev_dbg(&cpm->ofdev->dev, "i2c_ram %p, i2c_addr 0x%04x\n",
cpm->i2c_ram, cpm->i2c_addr);
dev_dbg(&cpm->ofdev->dev, "tbase 0x%04x, rbase 0x%04x\n",
(u8 __iomem *)cpm->tbase - DPRAM_BASE,
(u8 __iomem *)cpm->rbase - DPRAM_BASE);
cpm_command(cpm->cp_command, CPM_CR_INIT_TRX);
/*
* Select an invalid address. Just make sure we don't use loopback mode
*/
out_8(&cpm->i2c_reg->i2add, 0x7f << 1);
/*
* PDIV is set to 00 in i2mod, so brgclk/32 is used as input to the
* i2c baud rate generator. This is divided by 2 x (DIV + 3) to get
* the actual i2c bus frequency.
*/
brg = get_brgfreq() / (32 * 2 * cpm->freq) - 3;
out_8(&cpm->i2c_reg->i2brg, brg);
out_8(&cpm->i2c_reg->i2mod, 0x00);
out_8(&cpm->i2c_reg->i2com, I2COM_MASTER); /* Master mode */
/* Disable interrupts. */
out_8(&cpm->i2c_reg->i2cmr, 0);
out_8(&cpm->i2c_reg->i2cer, 0xff);
return 0;
out_muram:
for (i = 0; i < CPM_MAXBD; i++) {
if (cpm->rxbuf[i])
dma_free_coherent(NULL, CPM_MAX_READ + 1,
cpm->rxbuf[i], cpm->rxdma[i]);
if (cpm->txbuf[i])
dma_free_coherent(NULL, CPM_MAX_READ + 1,
cpm->txbuf[i], cpm->txdma[i]);
}
cpm_muram_free(cpm->dp_addr);
out_reg:
iounmap(cpm->i2c_reg);
out_ram:
if ((cpm->version == 1) && (!cpm->i2c_addr))
iounmap(cpm->i2c_ram);
if (cpm->version == 2)
cpm_muram_free(cpm->i2c_addr);
out_irq:
free_irq(cpm->irq, &cpm->adap);
return ret;
}
static void cpm_i2c_shutdown(struct cpm_i2c *cpm)
{
int i;
/* Shut down I2C. */
clrbits8(&cpm->i2c_reg->i2mod, I2MOD_EN);
/* Disable interrupts */
out_8(&cpm->i2c_reg->i2cmr, 0);
out_8(&cpm->i2c_reg->i2cer, 0xff);
free_irq(cpm->irq, &cpm->adap);
/* Free all memory */
for (i = 0; i < CPM_MAXBD; i++) {
dma_free_coherent(NULL, CPM_MAX_READ + 1,
cpm->rxbuf[i], cpm->rxdma[i]);
dma_free_coherent(NULL, CPM_MAX_READ + 1,
cpm->txbuf[i], cpm->txdma[i]);
}
cpm_muram_free(cpm->dp_addr);
iounmap(cpm->i2c_reg);
if ((cpm->version == 1) && (!cpm->i2c_addr))
iounmap(cpm->i2c_ram);
if (cpm->version == 2)
cpm_muram_free(cpm->i2c_addr);
}
static int __devinit cpm_i2c_probe(struct of_device *ofdev,
const struct of_device_id *match)
{
int result, len;
struct cpm_i2c *cpm;
const u32 *data;
cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL);
if (!cpm)
return -ENOMEM;
cpm->ofdev = ofdev;
dev_set_drvdata(&ofdev->dev, cpm);
cpm->adap = cpm_ops;
i2c_set_adapdata(&cpm->adap, cpm);
cpm->adap.dev.parent = &ofdev->dev;
result = cpm_i2c_setup(cpm);
if (result) {
dev_err(&ofdev->dev, "Unable to init hardware\n");
goto out_free;
}
/* register new adapter to i2c module... */
data = of_get_property(ofdev->node, "linux,i2c-index", &len);
if (data && len == 4) {
cpm->adap.nr = *data;
result = i2c_add_numbered_adapter(&cpm->adap);
} else
result = i2c_add_adapter(&cpm->adap);
if (result < 0) {
dev_err(&ofdev->dev, "Unable to register with I2C\n");
goto out_shut;
}
dev_dbg(&ofdev->dev, "hw routines for %s registered.\n",
cpm->adap.name);
/*
* register OF I2C devices
*/
of_register_i2c_devices(&cpm->adap, ofdev->node);
return 0;
out_shut:
cpm_i2c_shutdown(cpm);
out_free:
dev_set_drvdata(&ofdev->dev, NULL);
kfree(cpm);
return result;
}
static int __devexit cpm_i2c_remove(struct of_device *ofdev)
{
struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev);
i2c_del_adapter(&cpm->adap);
cpm_i2c_shutdown(cpm);
dev_set_drvdata(&ofdev->dev, NULL);
kfree(cpm);
return 0;
}
static const struct of_device_id cpm_i2c_match[] = {
{
.compatible = "fsl,cpm1-i2c",
},
{
.compatible = "fsl,cpm2-i2c",
},
{},
};
MODULE_DEVICE_TABLE(of, cpm_i2c_match);
static struct of_platform_driver cpm_i2c_driver = {
.match_table = cpm_i2c_match,
.probe = cpm_i2c_probe,
.remove = __devexit_p(cpm_i2c_remove),
.driver = {
.name = "fsl-i2c-cpm",
.owner = THIS_MODULE,
}
};
static int __init cpm_i2c_init(void)
{
return of_register_platform_driver(&cpm_i2c_driver);
}
static void __exit cpm_i2c_exit(void)
{
of_unregister_platform_driver(&cpm_i2c_driver);
}
module_init(cpm_i2c_init);
module_exit(cpm_i2c_exit);
MODULE_AUTHOR("Jochen Friedrich <jochen@scram.de>");
MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards");
MODULE_LICENSE("GPL");
