/*
* pata_oldpiix.c - Intel PATA/SATA controllers
*
* (C) 2005 Red Hat <alan@redhat.com>
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
* Early PIIX differs significantly from the later PIIX as it lacks
* SITRE and the slave timing registers. This means that you have to
* set timing per channel, or be clever. Libata tells us whenever it
* does drive selection and we use this to reload the timings.
*
* Because of these behaviour differences PIIX gets its own driver module.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>
#define DRV_NAME "pata_oldpiix"
#define DRV_VERSION "0.5.4"
/**
* oldpiix_pre_reset - probe begin
* @ap: ATA port
*
* Set up cable type and use generic probe init
*/
static int oldpiix_pre_reset(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits oldpiix_enable_bits[] = {
{ 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
{ 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
};
if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no]))
return -ENOENT;
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
/**
* oldpiix_pata_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
* @classes:
*
* LOCKING:
* None (inherited from caller).
*/
static void oldpiix_pata_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, oldpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* oldpiix_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: um
*
* Set PIO mode for device, in host controller PCI config space.
*
* LOCKING:
* None (inherited from caller).
*/
static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
unsigned int pio = adev->pio_mode - XFER_PIO_0;
struct pci_dev *dev = to_pci_dev(ap->host->dev);
unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
u16 idetm_data;
int control = 0;
/*
* See Intel Document 298600-004 for the timing programing rules
* for PIIX/ICH. Note that the early PIIX does not have the slave
* timing port at 0x44.
*/
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
if (pio > 1)
control |= 1; /* TIME */
if (ata_pio_need_iordy(adev))
control |= 2; /* IE */
/* Intel specifies that the prefetch/posting is for disk only */
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE */
pci_read_config_word(dev, idetm_port, &idetm_data);
/*
* Set PPE, IE and TIME as appropriate.
* Clear the other drive's timing bits.
*/
if (adev->devno == 0) {
idetm_data &= 0xCCE0;
idetm_data |= control;
} else {
idetm_data &= 0xCC0E;
idetm_data |= (control << 4);
}
idetm_data |= (timings[pio][0] << 12) |
(timings[pio][1] << 8);
pci_write_config_word(dev, idetm_port, idetm_data);
/* Track which port is configured */
ap->private_data = adev;
}
/**
* oldpiix_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
* @isich: True if the device is an ICH and has IOCFG registers
*
* Set MWDMA mode for device, in host controller PCI config space.
*
* LOCKING:
* None (inherited from caller).
*/
static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *dev = to_pci_dev(ap->host->dev);
u8 idetm_port = ap->port_no ? 0x42 : 0x40;
u16 idetm_data;
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
/*
* MWDMA is driven by the PIO timings. We must also enable
* IORDY unconditionally along with TIME1. PPE has already
* been set when the PIO timing was set.
*/
unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
unsigned int control;
const unsigned int needed_pio[3] = {
XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
};
int pio = needed_pio[mwdma] - XFER_PIO_0;
pci_read_config_word(dev, idetm_port, &idetm_data);
control = 3; /* IORDY|TIME0 */
/* Intel specifies that the PPE functionality is for disk only */
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE enable */
/* If the drive MWDMA is faster than it can do PIO then
we must force PIO into PIO0 */
if (adev->pio_mode < needed_pio[mwdma])
/* Enable DMA timing only */
control |= 8; /* PIO cycles in PIO0 */
/* Mask out the relevant control and timing bits we will load. Also
clear the other drive TIME register as a precaution */
if (adev->devno == 0) {
idetm_data &= 0xCCE0;
idetm_data |= control;
} else {
idetm_data &= 0xCC0E;
idetm_data |= (control << 4);
}
idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
pci_write_config_word(dev, idetm_port, idetm_data);
/* Track which port is configured */
ap->private_data = adev;
}
/**
* oldpiix_qc_issue_prot - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
* neccessary. Our logic also clears TIME0/TIME1 for the other device so
* that, even if we get this wrong, cycles to the other device will
* be made PIO0.
*/
static unsigned int oldpiix_qc_issue_prot(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
if (adev != ap->private_data) {
oldpiix_set_piomode(ap, adev);
if (adev->dma_mode)
oldpiix_set_dmamode(ap, adev);
}
return ata_qc_issue_prot(qc);
}
static struct scsi_host_template oldpiix_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
#ifdef CONFIG_PM
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
#endif
};
static const struct ata_port_operations oldpiix_pata_ops = {
.port_disable = ata_port_disable,
.set_piomode = oldpiix_set_piomode,
.set_dmamode = oldpiix_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = oldpiix_pata_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = oldpiix_qc_issue_prot,
.data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_port_start,
};
/**
* oldpiix_init_one - Register PIIX ATA PCI device with kernel services
* @pdev: PCI device to register
* @ent: Entry in oldpiix_pci_tbl matching with @pdev
*
* Called from kernel PCI layer. We probe for combined mode (sigh),
* and then hand over control to libata, for it to do the rest.
*
* LOCKING:
* Inherited from PCI layer (may sleep).
*
* RETURNS:
* Zero on success, or -ERRNO value.
*/
static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
static struct ata_port_info info = {
.sht = &oldpiix_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.port_ops = &oldpiix_pata_ops,
};
static struct ata_port_info *port_info[2] = { &info, &info };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
return ata_pci_init_one(pdev, port_info, 2);
}
static const struct pci_device_id oldpiix_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x1230), },
{ } /* terminate list */
};
static struct pci_driver oldpiix_pci_driver = {
.name = DRV_NAME,
.id_table = oldpiix_pci_tbl,
.probe = oldpiix_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
static int __init oldpiix_init(void)
{
return pci_register_driver(&oldpiix_pci_driver);
}
static void __exit oldpiix_exit(void)
{
pci_unregister_driver(&oldpiix_pci_driver);
}
module_init(oldpiix_init);
module_exit(oldpiix_exit);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl);
MODULE_VERSION(DRV_VERSION);
