/*
* pata_mpiix.c - Intel MPIIX PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* The MPIIX is different enough to the PIIX4 and friends that we give it
* a separate driver. The old ide/pci code handles this by just not tuning
* MPIIX at all.
*
* The MPIIX also differs in another important way from the majority of PIIX
* devices. The chip is a bridge (pardon the pun) between the old world of
* ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual
* IDE controller is not decoded in PCI space and the chip does not claim to
* be IDE class PCI. This requires slightly non-standard probe logic compared
* with PCI IDE and also that we do not disable the device when our driver is
* unloaded (as it has many other functions).
*
* The driver conciously keeps this logic internally to avoid pushing quirky
* PATA history into the clean libata layer.
*
* Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA
* hard disk present this driver will not detect it. This is not a bug. In this
* configuration the secondary port of the MPIIX is disabled and the addresses
* are decoded by the PCMCIA bridge and therefore are for a generic IDE driver
* to operate.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
#define DRV_VERSION "0.7.6"
enum {
IDETIM = 0x6C, /* IDE control register */
IORDY = (1 << 1),
PPE = (1 << 2),
FTIM = (1 << 0),
ENABLED = (1 << 15),
SECONDARY = (1 << 14)
};
static int mpiix_pre_reset(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
return -ENOENT;
return ata_std_prereset(ap);
}
/**
* mpiix_error_handler - probe reset
* @ap: ATA port
*
* Perform the ATA probe and bus reset sequence plus specific handling
* for this hardware. The MPIIX has the enable bits in a different place
* to PIIX4 and friends. As a pure PIO device it has no cable detect
*/
static void mpiix_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, mpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* mpiix_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. The MPIIX allows us to program the
* IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether
* prefetching or IORDY are used.
*
* This would get very ugly because we can only program timing for one
* device at a time, the other gets PIO0. Fortunately libata calls
* our qc_issue_prot command before a command is issued so we can
* flip the timings back and forth to reduce the pain.
*/
static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
int control = 0;
int pio = adev->pio_mode - XFER_PIO_0;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 idetim;
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
pci_read_config_word(pdev, IDETIM, &idetim);
/* Mask the IORDY/TIME/PPE for this device */
if (adev->class == ATA_DEV_ATA)
control |= PPE; /* Enable prefetch/posting for disk */
if (ata_pio_need_iordy(adev))
control |= IORDY;
if (pio > 1)
control |= FTIM; /* This drive is on the fast timing bank */
/* Mask out timing and clear both TIME bank selects */
idetim &= 0xCCEE;
idetim &= ~(0x07 << (4 * adev->devno));
idetim |= control << (4 * adev->devno);
idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
pci_write_config_word(pdev, IDETIM, idetim);
/* We use ap->private_data as a pointer to the device currently
loaded for timing */
ap->private_data = adev;
}
/**
* mpiix_qc_issue_prot - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
* neccessary. Our logic also clears TIME0/TIME1 for the other device so
* that, even if we get this wrong, cycles to the other device will
* be made PIO0.
*/
static unsigned int mpiix_qc_issue_prot(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
/* If modes have been configured and the channel data is not loaded
then load it. We have to check if pio_mode is set as the core code
does not set adev->pio_mode to XFER_PIO_0 while probing as would be
logical */
if (adev->pio_mode && adev != ap->private_data)
mpiix_set_piomode(ap, adev);
return ata_qc_issue_prot(qc);
}
static struct scsi_host_template mpiix_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
#ifdef CONFIG_PM
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
#endif
};
static struct ata_port_operations mpiix_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = mpiix_set_piomode,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = mpiix_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ata_cable_40wire,
.qc_prep = ata_qc_prep,
.qc_issue = mpiix_qc_issue_prot,
.data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_port_start,
};
static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* Single threaded by the PCI probe logic */
static struct ata_probe_ent probe;
static int printed_version;
void __iomem *cmd_addr, *ctl_addr;
u16 idetim;
int irq;
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
/* MPIIX has many functions which can be turned on or off according
to other devices present. Make sure IDE is enabled before we try
and use it */
pci_read_config_word(dev, IDETIM, &idetim);
if (!(idetim & ENABLED))
return -ENODEV;
/* See if it's primary or secondary channel... */
if (!(idetim & SECONDARY)) {
irq = 14;
cmd_addr = devm_ioport_map(&dev->dev, 0x1F0, 8);
ctl_addr = devm_ioport_map(&dev->dev, 0x3F6, 1);
} else {
irq = 15;
cmd_addr = devm_ioport_map(&dev->dev, 0x170, 8);
ctl_addr = devm_ioport_map(&dev->dev, 0x376, 1);
}
if (!cmd_addr || !ctl_addr)
return -ENOMEM;
/* We do our own plumbing to avoid leaking special cases for whacko
ancient hardware into the core code. There are two issues to
worry about. #1 The chip is a bridge so if in legacy mode and
without BARs set fools the setup. #2 If you pci_disable_device
the MPIIX your box goes castors up */
INIT_LIST_HEAD(&probe.node);
probe.dev = pci_dev_to_dev(dev);
probe.port_ops = &mpiix_port_ops;
probe.sht = &mpiix_sht;
probe.pio_mask = 0x1F;
probe.irq_flags = IRQF_SHARED;
probe.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
probe.n_ports = 1;
probe.irq = irq;
probe.port[0].cmd_addr = cmd_addr;
probe.port[0].ctl_addr = ctl_addr;
probe.port[0].altstatus_addr = ctl_addr;
/* Let libata fill in the port details */
ata_std_ports(&probe.port[0]);
/* Now add the port that is active */
if (ata_device_add(&probe))
return 0;
return -ENODEV;
}
static const struct pci_device_id mpiix[] = {
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
{ },
};
static struct pci_driver mpiix_pci_driver = {
.name = DRV_NAME,
.id_table = mpiix,
.probe = mpiix_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
static int __init mpiix_init(void)
{
return pci_register_driver(&mpiix_pci_driver);
}
static void __exit mpiix_exit(void)
{
pci_unregister_driver(&mpiix_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, mpiix);
MODULE_VERSION(DRV_VERSION);
module_init(mpiix_init);
module_exit(mpiix_exit);
