/*
* ata-it821x.c - IT821x PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* based upon
*
* it821x.c
*
* linux/drivers/ide/pci/it821x.c Version 0.09 December 2004
*
* Copyright (C) 2004 Red Hat <alan@redhat.com>
*
* May be copied or modified under the terms of the GNU General Public License
* Based in part on the ITE vendor provided SCSI driver.
*
* Documentation available from
* http://www.ite.com.tw/pc/IT8212F_V04.pdf
* Some other documents are NDA.
*
* The ITE8212 isn't exactly a standard IDE controller. It has two
* modes. In pass through mode then it is an IDE controller. In its smart
* mode its actually quite a capable hardware raid controller disguised
* as an IDE controller. Smart mode only understands DMA read/write and
* identify, none of the fancier commands apply. The IT8211 is identical
* in other respects but lacks the raid mode.
*
* Errata:
* o Rev 0x10 also requires master/slave hold the same DMA timings and
* cannot do ATAPI MWDMA.
* o The identify data for raid volumes lacks CHS info (technically ok)
* but also fails to set the LBA28 and other bits. We fix these in
* the IDE probe quirk code.
* o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
* raid then the controller firmware dies
* o Smart mode without RAID doesn't clear all the necessary identify
* bits to reduce the command set to the one used
*
* This has a few impacts on the driver
* - In pass through mode we do all the work you would expect
* - In smart mode the clocking set up is done by the controller generally
* but we must watch the other limits and filter.
* - There are a few extra vendor commands that actually talk to the
* controller but only work PIO with no IRQ.
*
* Vendor areas of the identify block in smart mode are used for the
* timing and policy set up. Each HDD in raid mode also has a serial
* block on the disk. The hardware extra commands are get/set chip status,
* rebuild, get rebuild status.
*
* In Linux the driver supports pass through mode as if the device was
* just another IDE controller. If the smart mode is running then
* volumes are managed by the controller firmware and each IDE "disk"
* is a raid volume. Even more cute - the controller can do automated
* hotplug and rebuild.
*
* The pass through controller itself is a little demented. It has a
* flaw that it has a single set of PIO/MWDMA timings per channel so
* non UDMA devices restrict each others performance. It also has a
* single clock source per channel so mixed UDMA100/133 performance
* isn't perfect and we have to pick a clock. Thankfully none of this
* matters in smart mode. ATAPI DMA is not currently supported.
*
* It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
*
* TODO
* - ATAPI and other speed filtering
* - Command filter in smart mode
* - RAID configuration ioctls
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_it821x"
#define DRV_VERSION "0.3.3"
struct it821x_dev
{
unsigned int smart:1, /* Are we in smart raid mode */
timing10:1; /* Rev 0x10 */
u8 clock_mode; /* 0, ATA_50 or ATA_66 */
u8 want[2][2]; /* Mode/Pri log for master slave */
/* We need these for switching the clock when DMA goes on/off
The high byte is the 66Mhz timing */
u16 pio[2]; /* Cached PIO values */
u16 mwdma[2]; /* Cached MWDMA values */
u16 udma[2]; /* Cached UDMA values (per drive) */
u16 last_device; /* Master or slave loaded ? */
};
#define ATA_66 0
#define ATA_50 1
#define ATA_ANY 2
#define UDMA_OFF 0
#define MWDMA_OFF 0
/*
* We allow users to force the card into non raid mode without
* flashing the alternative BIOS. This is also neccessary right now
* for embedded platforms that cannot run a PC BIOS but are using this
* device.
*/
static int it8212_noraid;
/**
* it821x_pre_reset - probe
* @ap: ATA port
*
* Set the cable type
*/
static int it821x_pre_reset(struct ata_port *ap)
{
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
/**
* it821x_error_handler - probe/reset
* @ap: ATA port
*
* Set the cable type and trigger a probe
*/
static void it821x_error_handler(struct ata_port *ap)
{
return ata_bmdma_drive_eh(ap, it821x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* it821x_program - program the PIO/MWDMA registers
* @ap: ATA port
* @adev: Device to program
* @timing: Timing value (66Mhz in top 8bits, 50 in the low 8)
*
* Program the PIO/MWDMA timing for this channel according to the
* current clock. These share the same register so are managed by
* the DMA start/stop sequence as with the old driver.
*/
static void it821x_program(struct ata_port *ap, struct ata_device *adev, u16 timing)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct it821x_dev *itdev = ap->private_data;
int channel = ap->port_no;
u8 conf;
/* Program PIO/MWDMA timing bits */
if (itdev->clock_mode == ATA_66)
conf = timing >> 8;
else
conf = timing & 0xFF;
pci_write_config_byte(pdev, 0x54 + 4 * channel, conf);
}
/**
* it821x_program_udma - program the UDMA registers
* @ap: ATA port
* @adev: ATA device to update
* @timing: Timing bits. Top 8 are for 66Mhz bottom for 50Mhz
*
* Program the UDMA timing for this drive according to the
* current clock. Handles the dual clocks and also knows about
* the errata on the 0x10 revision. The UDMA errata is partly handled
* here and partly in start_dma.
*/
static void it821x_program_udma(struct ata_port *ap, struct ata_device *adev, u16 timing)
{
struct it821x_dev *itdev = ap->private_data;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int channel = ap->port_no;
int unit = adev->devno;
u8 conf;
/* Program UDMA timing bits */
if (itdev->clock_mode == ATA_66)
conf = timing >> 8;
else
conf = timing & 0xFF;
if (itdev->timing10 == 0)
pci_write_config_byte(pdev, 0x56 + 4 * channel + unit, conf);
else {
/* Early revision must be programmed for both together */
pci_write_config_byte(pdev, 0x56 + 4 * channel, conf);
pci_write_config_byte(pdev, 0x56 + 4 * channel + 1, conf);
}
}
/**
* it821x_clock_strategy
* @ap: ATA interface
* @adev: ATA device being updated
*
* Select between the 50 and 66Mhz base clocks to get the best
* results for this interface.
*/
static void it821x_clock_strategy(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct it821x_dev *itdev = ap->private_data;
u8 unit = adev->devno;
struct ata_device *pair = ata_dev_pair(adev);
int clock, altclock;
u8 v;
int sel = 0;
/* Look for the most wanted clocking */
if (itdev->want[0][0] > itdev->want[1][0]) {
clock = itdev->want[0][1];
altclock = itdev->want[1][1];
} else {
clock = itdev->want[1][1];
altclock = itdev->want[0][1];
}
/* Master doesn't care does the slave ? */
if (clock == ATA_ANY)
clock = altclock;
/* Nobody cares - keep the same clock */
if (clock == ATA_ANY)
return;
/* No change */
if (clock == itdev->clock_mode)
return;
/* Load this into the controller */
if (clock == ATA_66)
itdev->clock_mode = ATA_66;
else {
itdev->clock_mode = ATA_50;
sel = 1;
}
pci_read_config_byte(pdev, 0x50, &v);
v &= ~(1 << (1 + ap->port_no));
v |= sel << (1 + ap->port_no);
pci_write_config_byte(pdev, 0x50, v);
/*
* Reprogram the UDMA/PIO of the pair drive for the switch
* MWDMA will be dealt with by the dma switcher
*/
if (pair && itdev->udma[1-unit] != UDMA_OFF) {
it821x_program_udma(ap, pair, itdev->udma[1-unit]);
it821x_program(ap, pair, itdev->pio[1-unit]);
}
/*
* Reprogram the UDMA/PIO of our drive for the switch.
* MWDMA will be dealt with by the dma switcher
*/
if (itdev->udma[unit] != UDMA_OFF) {
it821x_program_udma(ap, adev, itdev->udma[unit]);
it821x_program(ap, adev, itdev->pio[unit]);
}
}
/**
* it821x_passthru_set_piomode - set PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Configure for PIO mode. This is complicated as the register is
* shared by PIO and MWDMA and for both channels.
*/
static void it821x_passthru_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
/* Spec says 89 ref driver uses 88 */
static const u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
static const u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
struct it821x_dev *itdev = ap->private_data;
int unit = adev->devno;
int mode_wanted = adev->pio_mode - XFER_PIO_0;
/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
itdev->want[unit][1] = pio_want[mode_wanted];
itdev->want[unit][0] = 1; /* PIO is lowest priority */
itdev->pio[unit] = pio[mode_wanted];
it821x_clock_strategy(ap, adev);
it821x_program(ap, adev, itdev->pio[unit]);
}
/**
* it821x_passthru_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Set up the DMA modes. The actions taken depend heavily on the mode
* to use. If UDMA is used as is hopefully the usual case then the
* timing register is private and we need only consider the clock. If
* we are using MWDMA then we have to manage the setting ourself as
* we switch devices and mode.
*/
static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
static const u16 dma[] = { 0x8866, 0x3222, 0x3121 };
static const u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
static const u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
static const u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct it821x_dev *itdev = ap->private_data;
int channel = ap->port_no;
int unit = adev->devno;
u8 conf;
if (adev->dma_mode >= XFER_UDMA_0) {
int mode_wanted = adev->dma_mode - XFER_UDMA_0;
itdev->want[unit][1] = udma_want[mode_wanted];
itdev->want[unit][0] = 3; /* UDMA is high priority */
itdev->mwdma[unit] = MWDMA_OFF;
itdev->udma[unit] = udma[mode_wanted];
if (mode_wanted >= 5)
itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
/* UDMA on. Again revision 0x10 must do the pair */
pci_read_config_byte(pdev, 0x50, &conf);
if (itdev->timing10)
conf &= channel ? 0x9F: 0xE7;
else
conf &= ~ (1 << (3 + 2 * channel + unit));
pci_write_config_byte(pdev, 0x50, conf);
it821x_clock_strategy(ap, adev);
it821x_program_udma(ap, adev, itdev->udma[unit]);
} else {
int mode_wanted = adev->dma_mode - XFER_MW_DMA_0;
itdev->want[unit][1] = mwdma_want[mode_wanted];
itdev->want[unit][0] = 2; /* MWDMA is low priority */
itdev->mwdma[unit] = dma[mode_wanted];
itdev->udma[unit] = UDMA_OFF;
/* UDMA bits off - Revision 0x10 do them in pairs */
pci_read_config_byte(pdev, 0x50, &conf);
if (itdev->timing10)
conf |= channel ? 0x60: 0x18;
else
conf |= 1 << (3 + 2 * channel + unit);
pci_write_config_byte(pdev, 0x50, conf);
it821x_clock_strategy(ap, adev);
}
}
/**
* it821x_passthru_dma_start - DMA start callback
* @qc: Command in progress
*
* Usually drivers set the DMA timing at the point the set_dmamode call
* is made. IT821x however requires we load new timings on the
* transitions in some cases.
*/
static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
struct it821x_dev *itdev = ap->private_data;
int unit = adev->devno;
if (itdev->mwdma[unit] != MWDMA_OFF)
it821x_program(ap, adev, itdev->mwdma[unit]);
else if (itdev->udma[unit] != UDMA_OFF && itdev->timing10)
it821x_program_udma(ap, adev, itdev->udma[unit]);
ata_bmdma_start(qc);
}
/**
* it821x_passthru_dma_stop - DMA stop callback
* @qc: ATA command
*
* We loaded new timings in dma_start, as a result we need to restore
* the PIO timings in dma_stop so that the next command issue gets the
* right clock values.
*/
static void it821x_passthru_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
struct it821x_dev *itdev = ap->private_data;
int unit = adev->devno;
ata_bmdma_stop(qc);
if (itdev->mwdma[unit] != MWDMA_OFF)
it821x_program(ap, adev, itdev->pio[unit]);
}
/**
* it821x_passthru_dev_select - Select master/slave
* @ap: ATA port
* @device: Device number (not pointer)
*
* Device selection hook. If neccessary perform clock switching
*/
static void it821x_passthru_dev_select(struct ata_port *ap,
unsigned int device)
{
struct it821x_dev *itdev = ap->private_data;
if (itdev && device != itdev->last_device) {
struct ata_device *adev = &ap->device[device];
it821x_program(ap, adev, itdev->pio[adev->devno]);
itdev->last_device = device;
}
ata_std_dev_select(ap, device);
}
/**
* it821x_smart_qc_issue_prot - wrap qc issue prot
* @qc: command
*
* Wrap the command issue sequence for the IT821x. We need to
* perform out own device selection timing loads before the
* usual happenings kick off
*/
static unsigned int it821x_smart_qc_issue_prot(struct ata_queued_cmd *qc)
{
switch(qc->tf.command)
{
/* Commands the firmware supports */
case ATA_CMD_READ:
case ATA_CMD_READ_EXT:
case ATA_CMD_WRITE:
case ATA_CMD_WRITE_EXT:
case ATA_CMD_PIO_READ:
case ATA_CMD_PIO_READ_EXT:
case ATA_CMD_PIO_WRITE:
case ATA_CMD_PIO_WRITE_EXT:
case ATA_CMD_READ_MULTI:
case ATA_CMD_READ_MULTI_EXT:
case ATA_CMD_WRITE_MULTI:
case ATA_CMD_WRITE_MULTI_EXT:
case ATA_CMD_ID_ATA:
/* Arguably should just no-op this one */
case ATA_CMD_SET_FEATURES:
return ata_qc_issue_prot(qc);
}
printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command);
return AC_ERR_INVALID;
}
/**
* it821x_passthru_qc_issue_prot - wrap qc issue prot
* @qc: command
*
* Wrap the command issue sequence for the IT821x. We need to
* perform out own device selection timing loads before the
* usual happenings kick off
*/
static unsigned int it821x_passthru_qc_issue_prot(struct ata_queued_cmd *qc)
{
it821x_passthru_dev_select(qc->ap, qc->dev->devno);
return ata_qc_issue_prot(qc);
}
/**
* it821x_smart_set_mode - mode setting
* @ap: interface to set up
* @unused: device that failed (error only)
*
* Use a non standard set_mode function. We don't want to be tuned.
* The BIOS configured everything. Our job is not to fiddle. We
* read the dma enabled bits from the PCI configuration of the device
* and respect them.
*/
static int it821x_smart_set_mode(struct ata_port *ap, struct ata_device **unused)
{
int dma_enabled = 0;
int i;
/* Bits 5 and 6 indicate if DMA is active on master/slave */
/* It is possible that BMDMA isn't allocated */
if (ap->ioaddr.bmdma_addr)
dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
if (ata_dev_enabled(dev)) {
/* We don't really care */
dev->pio_mode = XFER_PIO_0;
dev->dma_mode = XFER_MW_DMA_0;
/* We do need the right mode information for DMA or PIO
and this comes from the current configuration flags */
if (dma_enabled & (1 << (5 + i))) {
dev->xfer_mode = XFER_MW_DMA_0;
dev->xfer_shift = ATA_SHIFT_MWDMA;
dev->flags &= ~ATA_DFLAG_PIO;
} else {
dev->xfer_mode = XFER_PIO_0;
dev->xfer_shift = ATA_SHIFT_PIO;
dev->flags |= ATA_DFLAG_PIO;
}
}
}
return 0;
}
/**
* it821x_dev_config - Called each device identify
* @ap: ATA port
* @adev: Device that has just been identified
*
* Perform the initial setup needed for each device that is chip
* special. In our case we need to lock the sector count to avoid
* blowing the brains out of the firmware with large LBA48 requests
*
* FIXME: When FUA appears we need to block FUA too. And SMART and
* basically we need to filter commands for this chip.
*/
static void it821x_dev_config(struct ata_port *ap, struct ata_device *adev)
{
unsigned char model_num[40];
char *s;
unsigned int len;
/* This block ought to be a library routine as it is in several
drivers now */
ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS,
sizeof(model_num));
s = &model_num[0];
len = strnlen(s, sizeof(model_num));
/* ATAPI specifies that empty space is blank-filled; remove blanks */
while ((len > 0) && (s[len - 1] == ' ')) {
len--;
s[len] = 0;
}
if (adev->max_sectors > 255)
adev->max_sectors = 255;
if (strstr(model_num, "Integrated Technology Express")) {
/* RAID mode */
printk(KERN_INFO "IT821x %sRAID%d volume",
adev->id[147]?"Bootable ":"",
adev->id[129]);
if (adev->id[129] != 1)
printk("(%dK stripe)", adev->id[146]);
printk(".\n");
}
}
/**
* it821x_check_atapi_dma - ATAPI DMA handler
* @qc: Command we are about to issue
*
* Decide if this ATAPI command can be issued by DMA on this
* controller. Return 0 if it can be.
*/
static int it821x_check_atapi_dma(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct it821x_dev *itdev = ap->private_data;
/* No ATAPI DMA in smart mode */
if (itdev->smart)
return -EOPNOTSUPP;
/* No ATAPI DMA on rev 10 */
if (itdev->timing10)
return -EOPNOTSUPP;
/* Cool */
return 0;
}
/**
* it821x_port_start - port setup
* @ap: ATA port being set up
*
* The it821x needs to maintain private data structures and also to
* use the standard PCI interface which lacks support for this
* functionality. We instead set up the private data on the port
* start hook, and tear it down on port stop
*/
static int it821x_port_start(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct it821x_dev *itdev;
u8 conf;
int ret = ata_port_start(ap);
if (ret < 0)
return ret;
ap->private_data = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL);
if (ap->private_data == NULL) {
ata_port_stop(ap);
return -ENOMEM;
}
itdev = ap->private_data;
memset(itdev, 0, sizeof(struct it821x_dev));
pci_read_config_byte(pdev, 0x50, &conf);
if (conf & 1) {
itdev->smart = 1;
/* Long I/O's although allowed in LBA48 space cause the
onboard firmware to enter the twighlight zone */
/* No ATAPI DMA in this mode either */
}
/* Pull the current clocks from 0x50 */
if (conf & (1 << (1 + ap->port_no)))
itdev->clock_mode = ATA_50;
else
itdev->clock_mode = ATA_66;
itdev->want[0][1] = ATA_ANY;
itdev->want[1][1] = ATA_ANY;
itdev->last_device = -1;
pci_read_config_byte(pdev, PCI_REVISION_ID, &conf);
if (conf == 0x10) {
itdev->timing10 = 1;
/* Need to disable ATAPI DMA for this case */
if (!itdev->smart)
printk(KERN_WARNING DRV_NAME": Revision 0x10, workarounds activated.\n");
}
return 0;
}
/**
* it821x_port_stop - port shutdown
* @ap: ATA port being removed
*
* Release the private objects we added in it821x_port_start
*/
static void it821x_port_stop(struct ata_port *ap) {
kfree(ap->private_data);
ap->private_data = NULL; /* We want an OOPS if we reuse this
too late! */
ata_port_stop(ap);
}
static struct scsi_host_template it821x_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations it821x_smart_port_ops = {
.set_mode = it821x_smart_set_mode,
.port_disable = ata_port_disable,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.mode_filter = ata_pci_default_filter,
.check_status = ata_check_status,
.check_atapi_dma= it821x_check_atapi_dma,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.dev_config = it821x_dev_config,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = it821x_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = it821x_smart_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = it821x_port_start,
.port_stop = it821x_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations it821x_passthru_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = it821x_passthru_set_piomode,
.set_dmamode = it821x_passthru_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.check_atapi_dma= it821x_check_atapi_dma,
.dev_select = it821x_passthru_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = it821x_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = it821x_passthru_bmdma_start,
.bmdma_stop = it821x_passthru_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = it821x_passthru_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_clear = ata_bmdma_irq_clear,
.irq_handler = ata_interrupt,
.port_start = it821x_port_start,
.port_stop = it821x_port_stop,
.host_stop = ata_host_stop
};
static void __devinit it821x_disable_raid(struct pci_dev *pdev)
{
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(pdev, 0x5E, 0x01);
/* Set to bypass mode, and reset PCI bus */
pci_write_config_byte(pdev, 0x50, 0x00);
pci_write_config_word(pdev, PCI_COMMAND,
PCI_COMMAND_PARITY | PCI_COMMAND_IO |
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
pci_write_config_word(pdev, 0x40, 0xA0F3);
pci_write_config_dword(pdev,0x4C, 0x02040204);
pci_write_config_byte(pdev, 0x42, 0x36);
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20);
}
static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
u8 conf;
static struct ata_port_info info_smart = {
.sht = &it821x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &it821x_smart_port_ops
};
static struct ata_port_info info_passthru = {
.sht = &it821x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7f,
.port_ops = &it821x_passthru_port_ops
};
static struct ata_port_info *port_info[2];
static char *mode[2] = { "pass through", "smart" };
/* Force the card into bypass mode if so requested */
if (it8212_noraid) {
printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
it821x_disable_raid(pdev);
}
pci_read_config_byte(pdev, 0x50, &conf);
conf &= 1;
printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]);
if (conf == 0)
port_info[0] = port_info[1] = &info_passthru;
else
port_info[0] = port_info[1] = &info_smart;
return ata_pci_init_one(pdev, port_info, 2);
}
static int it821x_reinit_one(struct pci_dev *pdev)
{
/* Resume - turn raid back off if need be */
if (it8212_noraid)
it821x_disable_raid(pdev);
return ata_pci_device_resume(pdev);
}
static const struct pci_device_id it821x[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
{ },
};
static struct pci_driver it821x_pci_driver = {
.name = DRV_NAME,
.id_table = it821x,
.probe = it821x_init_one,
.remove = ata_pci_remove_one,
.suspend = ata_pci_device_suspend,
.resume = it821x_reinit_one,
};
static int __init it821x_init(void)
{
return pci_register_driver(&it821x_pci_driver);
}
static void __exit it821x_exit(void)
{
pci_unregister_driver(&it821x_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, it821x);
MODULE_VERSION(DRV_VERSION);
module_param_named(noraid, it8212_noraid, int, S_IRUGO);
MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
module_init(it821x_init);
module_exit(it821x_exit);
