/*
* pata_cypress.c - Cypress PATA for new ATA layer
* (C) 2006 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* Based heavily on
* linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_cypress"
#define DRV_VERSION "0.1.4"
/* here are the offset definitions for the registers */
enum {
CY82_IDE_CMDREG = 0x04,
CY82_IDE_ADDRSETUP = 0x48,
CY82_IDE_MASTER_IOR = 0x4C,
CY82_IDE_MASTER_IOW = 0x4D,
CY82_IDE_SLAVE_IOR = 0x4E,
CY82_IDE_SLAVE_IOW = 0x4F,
CY82_IDE_MASTER_8BIT = 0x50,
CY82_IDE_SLAVE_8BIT = 0x51,
CY82_INDEX_PORT = 0x22,
CY82_DATA_PORT = 0x23,
CY82_INDEX_CTRLREG1 = 0x01,
CY82_INDEX_CHANNEL0 = 0x30,
CY82_INDEX_CHANNEL1 = 0x31,
CY82_INDEX_TIMEOUT = 0x32
};
/**
* cy82c693_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup.
*/
static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_timing t;
const unsigned long T = 1000000 / 33;
short time_16, time_8;
u32 addr;
if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) {
printk(KERN_ERR DRV_NAME ": mome computation failed.\n");
return;
}
time_16 = FIT(t.recover, 0, 15) | (FIT(t.active, 0, 15) << 4);
time_8 = FIT(t.act8b, 0, 15) | (FIT(t.rec8b, 0, 15) << 4);
if (adev->devno == 0) {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0x0F; /* Mask bits */
addr |= FIT(t.setup, 0, 15);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16);
pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8);
} else {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0xF0; /* Mask bits */
addr |= (FIT(t.setup, 0, 15) << 4);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8);
}
}
/**
* cy82c693_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the DMA mode setup.
*/
static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
int reg = CY82_INDEX_CHANNEL0 + ap->port_no;
/* Be afraid, be very afraid. Magic registers in low I/O space */
outb(reg, 0x22);
outb(adev->dma_mode - XFER_MW_DMA_0, 0x23);
/* 0x50 gives the best behaviour on the Alpha's using this chip */
outb(CY82_INDEX_TIMEOUT, 0x22);
outb(0x50, 0x23);
}
static struct scsi_host_template cy82c693_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
#ifdef CONFIG_PM
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
#endif
};
static struct ata_port_operations cy82c693_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = cy82c693_set_piomode,
.set_dmamode = cy82c693_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_port_start,
};
static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static struct ata_port_info info = {
.sht = &cy82c693_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cy82c693_port_ops
};
static struct ata_port_info *port_info[1] = { &info };
/* Devfn 1 is the ATA primary. The secondary is magic and on devfn2.
For the moment we don't handle the secondary. FIXME */
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
return ata_pci_init_one(pdev, port_info, 1);
}
static const struct pci_device_id cy82c693[] = {
{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), },
{ },
};
static struct pci_driver cy82c693_pci_driver = {
.name = DRV_NAME,
.id_table = cy82c693,
.probe = cy82c693_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
static int __init cy82c693_init(void)
{
return pci_register_driver(&cy82c693_pci_driver);
}
static void __exit cy82c693_exit(void)
{
pci_unregister_driver(&cy82c693_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cy82c693);
MODULE_VERSION(DRV_VERSION);
module_init(cy82c693_init);
module_exit(cy82c693_exit);
