/*
* Moorestown PCI support
* Copyright (c) 2008 Intel Corporation
* Jesse Barnes <jesse.barnes@intel.com>
*
* Moorestown has an interesting PCI implementation:
* - configuration space is memory mapped (as defined by MCFG)
* - Lincroft devices also have a real, type 1 configuration space
* - Early Lincroft silicon has a type 1 access bug that will cause
* a hang if non-existent devices are accessed
* - some devices have the "fixed BAR" capability, which means
* they can't be relocated or modified; check for that during
* BAR sizing
*
* So, we use the MCFG space for all reads and writes, but also send
* Lincroft writes to type 1 space. But only read/write if the device
* actually exists, otherwise return all 1s for reads and bit bucket
* the writes.
*/
#include <linux/sched.h>
#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/dmi.h>
#include <asm/acpi.h>
#include <asm/segment.h>
#include <asm/io.h>
#include <asm/smp.h>
#include <asm/pci_x86.h>
#include <asm/hw_irq.h>
#include <asm/io_apic.h>
#define PCIE_CAP_OFFSET 0x100
/* Fixed BAR fields */
#define PCIE_VNDR_CAP_ID_FIXED_BAR 0x00 /* Fixed BAR (TBD) */
#define PCI_FIXED_BAR_0_SIZE 0x04
#define PCI_FIXED_BAR_1_SIZE 0x08
#define PCI_FIXED_BAR_2_SIZE 0x0c
#define PCI_FIXED_BAR_3_SIZE 0x10
#define PCI_FIXED_BAR_4_SIZE 0x14
#define PCI_FIXED_BAR_5_SIZE 0x1c
/**
* fixed_bar_cap - return the offset of the fixed BAR cap if found
* @bus: PCI bus
* @devfn: device in question
*
* Look for the fixed BAR cap on @bus and @devfn, returning its offset
* if found or 0 otherwise.
*/
static int fixed_bar_cap(struct pci_bus *bus, unsigned int devfn)
{
int pos;
u32 pcie_cap = 0, cap_data;
pos = PCIE_CAP_OFFSET;
if (!raw_pci_ext_ops)
return 0;
while (pos) {
if (raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
devfn, pos, 4, &pcie_cap))
return 0;
if (pcie_cap == 0xffffffff)
return 0;
if (PCI_EXT_CAP_ID(pcie_cap) == PCI_EXT_CAP_ID_VNDR) {
raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
devfn, pos + 4, 4, &cap_data);
if ((cap_data & 0xffff) == PCIE_VNDR_CAP_ID_FIXED_BAR)
return pos;
}
pos = pcie_cap >> 20;
}
return 0;
}
static int pci_device_update_fixed(struct pci_bus *bus, unsigned int devfn,
int reg, int len, u32 val, int offset)
{
u32 size;
unsigned int domain, busnum;
int bar = (reg - PCI_BASE_ADDRESS_0) >> 2;
domain = pci_domain_nr(bus);
busnum = bus->number;
if (val == ~0 && len == 4) {
unsigned long decode;
raw_pci_ext_ops->read(domain, busnum, devfn,
offset + 8 + (bar * 4), 4, &size);
/* Turn the size into a decode pattern for the sizing code */
if (size) {
decode = size - 1;
decode |= decode >> 1;
decode |= decode >> 2;
decode |= decode >> 4;
decode |= decode >> 8;
decode |= decode >> 16;
decode++;
decode = ~(decode - 1);
} else {
decode = ~0;
}
/*
* If val is all ones, the core code is trying to size the reg,
* so update the mmconfig space with the real size.
*
* Note: this assumes the fixed size we got is a power of two.
*/
return raw_pci_ext_ops->write(domain, busnum, devfn, reg, 4,
decode);
}
/* This is some other kind of BAR write, so just do it. */
return raw_pci_ext_ops->write(domain, busnum, devfn, reg, len, val);
}
/**
* type1_access_ok - check whether to use type 1
* @bus: bus number
* @devfn: device & function in question
*
* If the bus is on a Lincroft chip and it exists, or is not on a Lincroft at
* all, the we can go ahead with any reads & writes. If it's on a Lincroft,
* but doesn't exist, avoid the access altogether to keep the chip from
* hanging.
*/
static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg)
{
/* This is a workaround for A0 LNC bug where PCI status register does
* not have new CAP bit set. can not be written by SW either.
*
* PCI header type in real LNC indicates a single function device, this
* will prevent probing other devices under the same function in PCI
* shim. Therefore, use the header type in shim instead.
*/
if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE)
return 0;
if (bus == 0 && (devfn == PCI_DEVFN(2, 0) || devfn == PCI_DEVFN(0, 0)))
return 1;
return 0; /* langwell on others */
}
static int pci_read(struct pci_bus *bus, unsigned int devfn, int where,
int size, u32 *value)
{
if (type1_access_ok(bus->number, devfn, where))
return pci_direct_conf1.read(pci_domain_nr(bus), bus->number,
devfn, where, size, value);
return raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
devfn, where, size, value);
}
static int pci_write(struct pci_bus *bus, unsigned int devfn, int where,
int size, u32 value)
{
int offset;
/* On MRST, there is no PCI ROM BAR, this will cause a subsequent read
* to ROM BAR return 0 then being ignored.
*/
if (where == PCI_ROM_ADDRESS)
return 0;
/*
* Devices with fixed BARs need special handling:
* - BAR sizing code will save, write ~0, read size, restore
* - so writes to fixed BARs need special handling
* - other writes to fixed BAR devices should go through mmconfig
*/
offset = fixed_bar_cap(bus, devfn);
if (offset &&
(where >= PCI_BASE_ADDRESS_0 && where <= PCI_BASE_ADDRESS_5)) {
return pci_device_update_fixed(bus, devfn, where, size, value,
offset);
}
/*
* On Moorestown update both real & mmconfig space
* Note: early Lincroft silicon can't handle type 1 accesses to
* non-existent devices, so just eat the write in that case.
*/
if (type1_access_ok(bus->number, devfn, where))
return pci_direct_conf1.write(pci_domain_nr(bus), bus->number,
devfn, where, size, value);
return raw_pci_ext_ops->write(pci_domain_nr(bus), bus->number, devfn,
where, size, value);
}
static int mrst_pci_irq_enable(struct pci_dev *dev)
{
u8 pin;
struct io_apic_irq_attr irq_attr;
pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
/* MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to
* IOAPIC RTE entries, so we just enable RTE for the device.
*/
irq_attr.ioapic = mp_find_ioapic(dev->irq);
irq_attr.ioapic_pin = dev->irq;
irq_attr.trigger = 1; /* level */
irq_attr.polarity = 1; /* active low */
io_apic_set_pci_routing(&dev->dev, dev->irq, &irq_attr);
return 0;
}
struct pci_ops pci_mrst_ops = {
.read = pci_read,
.write = pci_write,
};
/**
* pci_mrst_init - installs pci_mrst_ops
*
* Moorestown has an interesting PCI implementation (see above).
* Called when the early platform detection installs it.
*/
int __init pci_mrst_init(void)
{
printk(KERN_INFO "Moorestown platform detected, using MRST PCI ops\n");
pci_mmcfg_late_init();
pcibios_enable_irq = mrst_pci_irq_enable;
pci_root_ops = pci_mrst_ops;
/* Continue with standard init */
return 1;
}
/*
* Langwell devices reside at fixed offsets, don't try to move them.
*/
static void __devinit pci_fixed_bar_fixup(struct pci_dev *dev)
{
unsigned long offset;
u32 size;
int i;
/* Fixup the BAR sizes for fixed BAR devices and make them unmoveable */
offset = fixed_bar_cap(dev->bus, dev->devfn);
if (!offset || PCI_DEVFN(2, 0) == dev->devfn ||
PCI_DEVFN(2, 2) == dev->devfn)
return;
for (i = 0; i < PCI_ROM_RESOURCE; i++) {
pci_read_config_dword(dev, offset + 8 + (i * 4), &size);
dev->resource[i].end = dev->resource[i].start + size - 1;
dev->resource[i].flags |= IORESOURCE_PCI_FIXED;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_fixed_bar_fixup);
