/*
* Low-Level PCI Support for the SH7780
*
* Dustin McIntire (dustin@sensoria.com)
* Derived from arch/i386/kernel/pci-*.c which bore the message:
* (c) 1999--2000 Martin Mares <mj@ucw.cz>
*
* Ported to the new API by Paul Mundt <lethal@linux-sh.org>
* With cleanup by Paul van Gool <pvangool@mimotech.com>
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
*/
#undef DEBUG
#include <linux/config.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/errno.h>
#include <linux/irq.h>
#include <linux/delay.h>
#include <asm/machvec.h>
#include <asm/io.h>
#include "pci-sh7780.h"
static unsigned int pci_probe = PCI_PROBE_CONF1;
extern int pci_fixup_pcic(void);
/*
* Direct access to PCI hardware...
*/
#define CONFIG_CMD(bus, devfn, where) (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
/*
* Functions for accessing PCI configuration space with type 1 accesses
*/
static int sh7780_pci_read(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 *val)
{
unsigned long flags;
u32 data;
/*
* PCIPDR may only be accessed as 32 bit words,
* so we must do byte alignment by hand
*/
local_irq_save(flags);
outl(CONFIG_CMD(bus, devfn, where), PCI_REG(SH7780_PCIPAR));
data = inl(PCI_REG(SH7780_PCIPDR));
local_irq_restore(flags);
switch (size) {
case 1:
*val = (data >> ((where & 3) << 3)) & 0xff;
break;
case 2:
*val = (data >> ((where & 2) << 3)) & 0xffff;
break;
case 4:
*val = data;
break;
default:
return PCIBIOS_FUNC_NOT_SUPPORTED;
}
return PCIBIOS_SUCCESSFUL;
}
/*
* Since SH7780 only does 32bit access we'll have to do a read,
* mask,write operation.
* We'll allow an odd byte offset, though it should be illegal.
*/
static int sh7780_pci_write(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 val)
{
unsigned long flags;
int shift;
u32 data;
local_irq_save(flags);
outl(CONFIG_CMD(bus, devfn, where), PCI_REG(SH7780_PCIPAR));
data = inl(PCI_REG(SH7780_PCIPDR));
local_irq_restore(flags);
switch (size) {
case 1:
shift = (where & 3) << 3;
data &= ~(0xff << shift);
data |= ((val & 0xff) << shift);
break;
case 2:
shift = (where & 2) << 3;
data &= ~(0xffff << shift);
data |= ((val & 0xffff) << shift);
break;
case 4:
data = val;
break;
default:
return PCIBIOS_FUNC_NOT_SUPPORTED;
}
outl(data, PCI_REG(SH7780_PCIPDR));
return PCIBIOS_SUCCESSFUL;
}
#undef CONFIG_CMD
struct pci_ops sh7780_pci_ops = {
.read = sh7780_pci_read,
.write = sh7780_pci_write,
};
static int __init pci_check_direct(void)
{
unsigned int tmp, id;
outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */
/* check for SH7780/SH7780R hardware */
id = inl(PCI_REG(SH7780_PCIVID));
if ((id != ((SH7780_DEVICE_ID << 16) | SH7780_VENDOR_ID)) &&
(id != ((SH7781_DEVICE_ID << 16) | SH7780_VENDOR_ID))) {
printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id);
return -ENODEV;
}
/*
* Check if configuration works.
*/
if (pci_probe & PCI_PROBE_CONF1) {
tmp = inl(PCI_REG(SH7780_PCIPAR));
outl(0x80000000, PCI_REG(SH7780_PCIPAR));
if (inl(PCI_REG(SH7780_PCIPAR)) == 0x80000000) {
outl(tmp, PCI_REG(SH7780_PCIPAR));
printk(KERN_INFO "PCI: Using configuration type 1\n");
request_region(PCI_REG(SH7780_PCIPAR), 8, "PCI conf1");
return 0;
}
outl(tmp, PCI_REG(SH7780_PCIPAR));
}
pr_debug("PCI: pci_check_direct failed\n");
return -EINVAL;
}
/***************************************************************************************/
/*
* Handle bus scanning and fixups ....
*/
static void __init pci_fixup_ide_bases(struct pci_dev *d)
{
int i;
/*
* PCI IDE controllers use non-standard I/O port decoding, respect it.
*/
if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE)
return;
pr_debug("PCI: IDE base address fixup for %s\n", pci_name(d));
for(i=0; i<4; i++) {
struct resource *r = &d->resource[i];
if ((r->start & ~0x80) == 0x374) {
r->start |= 2;
r->end = r->start;
}
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases);
/*
* Called after each bus is probed, but before its children
* are examined.
*/
void __init pcibios_fixup_bus(struct pci_bus *b)
{
pci_read_bridge_bases(b);
}
/*
* Initialization. Try all known PCI access methods. Note that we support
* using both PCI BIOS and direct access: in such cases, we use I/O ports
* to access config space.
*
* Note that the platform specific initialization (BSC registers, and memory
* space mapping) will be called via the machine vectors (sh_mv.mv_pci_init()) if it
* exists and via the platform defined function pcibios_init_platform().
* See pci_bigsur.c for implementation;
*
* The BIOS version of the pci functions is not yet implemented but it is left
* in for completeness. Currently an error will be genereated at compile time.
*/
static int __init sh7780_pci_init(void)
{
int ret;
pr_debug("PCI: Starting intialization.\n");
/* Setup the INTC */
ctrl_outl(0x00200000, INTC_ICR0); /* INTC SH-4 Mode */
ctrl_outl(0x00078000, INTC_INT2MSKCR); /* enable PCIINTA - PCIINTD */
ctrl_outl(0x40000000, INTC_INTMSK1); /* disable IRL4-7 Interrupt */
ctrl_outl(0x0000fffe, INTC_INTMSK2); /* disable IRL4-7 Interrupt */
ctrl_outl(0x80000000, INTC_INTMSKCLR1); /* enable IRL0-3 Interrupt */
ctrl_outl(0xfffe0000, INTC_INTMSKCLR2); /* enable IRL0-3 Interrupt */
if ((ret = pci_check_direct()) != 0)
return ret;
return pcibios_init_platform();
}
core_initcall(sh7780_pci_init);
int __init sh7780_pcic_init(struct sh7780_pci_address_map *map)
{
u32 word;
/*
* This code is unused for some boards as it is done in the
* bootloader and doing it here means the MAC addresses loaded
* by the bootloader get lost.
*/
if (!(map->flags & SH7780_PCIC_NO_RESET)) {
/* toggle PCI reset pin */
word = SH7780_PCICR_PREFIX | SH7780_PCICR_PRST;
outl(word,PCI_REG(SH7780_PCICR));
/* Wait for a long time... not 1 sec. but long enough */
mdelay(100);
word = SH7780_PCICR_PREFIX;
outl(word,PCI_REG(SH7780_PCICR));
}
/* set the command/status bits to:
* Wait Cycle Control + Parity Enable + Bus Master +
* Mem space enable
*/
outl(0x00000046, PCI_REG(SH7780_PCICMD));
/* define this host as the host bridge */
word = SH7780_PCI_HOST_BRIDGE << 24;
outl(word, PCI_REG(SH7780_PCIRID));
/* Set IO and Mem windows to local address
* Make PCI and local address the same for easy 1 to 1 mapping
* Window0 = map->window0.size @ non-cached area base = SDRAM
* Window1 = map->window1.size @ cached area base = SDRAM
*/
word = ((map->window0.size - 1) & 0x1ff00001) | 0x01;
outl(0x07f00001, PCI_REG(SH7780_PCILSR0));
word = ((map->window1.size - 1) & 0x1ff00001) | 0x01;
outl(0x00000001, PCI_REG(SH7780_PCILSR1));
/* Set the values on window 0 PCI config registers */
word = P2SEGADDR(map->window0.base);
outl(0xa8000000, PCI_REG(SH7780_PCILAR0));
outl(0x08000000, PCI_REG(SH7780_PCIMBAR0));
/* Set the values on window 1 PCI config registers */
word = P2SEGADDR(map->window1.base);
outl(0x00000000, PCI_REG(SH7780_PCILAR1));
outl(0x00000000, PCI_REG(SH7780_PCIMBAR1));
/* Map IO space into PCI IO window
* The IO window is 64K-PCIBIOS_MIN_IO in size
* IO addresses will be translated to the
* PCI IO window base address
*/
PCIDBG(3,"PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", PCIBIOS_MIN_IO,
(64*1024), SH7780_PCI_IO_BASE+PCIBIOS_MIN_IO);
/* NOTE: I'm ignoring the PCI error IRQs for now..
* TODO: add support for the internal error interrupts and
* DMA interrupts...
*/
#ifdef CONFIG_SH_R7780RP
pci_fixup_pcic();
#endif
/* SH7780 init done, set central function init complete */
/* use round robin mode to stop a device starving/overruning */
word = SH7780_PCICR_PREFIX | SH7780_PCICR_CFIN | /* SH7780_PCICR_ARBM |*/ SH7780_PCICR_FTO;
outl(word, PCI_REG(SH7780_PCICR));
return 1;
}
char * __init pcibios_setup(char *str)
{
if (!strcmp(str, "off")) {
pci_probe = 0;
return NULL;
}
return str;
}
/*
* IRQ functions
*/
static u8 __init sh7780_no_swizzle(struct pci_dev *dev, u8 *pin)
{
/* no swizzling */
return PCI_SLOT(dev->devfn);
}
static int sh7780_pci_lookup_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
int irq = -1;
/* now lookup the actual IRQ on a platform specific basis (pci-'platform'.c) */
irq = pcibios_map_platform_irq(slot,pin);
if( irq < 0 ) {
pr_debug("PCI: Error mapping IRQ on device %s\n", pci_name(dev));
return irq;
}
pr_debug("Setting IRQ for slot %s to %d\n", pci_name(dev), irq);
return irq;
}
void __init pcibios_fixup_irqs(void)
{
pci_fixup_irqs(sh7780_no_swizzle, sh7780_pci_lookup_irq);
}
